www.jbctools.com
CD-1BC/2BC/9BC
SOLDERING STATION
2
CD-1BC/2BC/9BC - SOLDERING STATION
It is imperative to follow safety guidelines to protect health and prevent electric shock,
injury, fire or explosions.
SAFETY
- The mains cable must be plugged into approved bases.
- The tool should be placed in the stand when not in use. This way the sleep mode will be activated.
- The soldering tip and the metal part of the tool may still be hot even when the station is turned off.
Handle with care.
- The stand can also be hot. To adjust its position, turn the station off and wait until the cartridge
cools down.
- Be careful with the remains of liquid tin. In contact with skin, it can cause burns.
- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation.
- Do not work on electrically live parts. Antistatic handle of soldering irons is electrically conductive.
- Be careful with the smoke produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working
to avoid any damage.
- This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
CAUTION
- Incorrect use of tool may cause fire.
- Be careful when using the tool in areas where inflamable products are stored.
- Heat can cause inflamable products to ignite even when not at sight.
3
T245-A
Handpiece
C245903
C245741
Cartridges
MANUAL
Power Cord
www. jbct ool s.co m
CD-1BC/2BC/9BC
SOLDERING STATION
S0354 Sponge
CL6210 Brass Wool
CD-1C / CD-2C / CD-9C
Control Unit
4
CD-1BC/2BC/9BC - SOLDERING STATION
Power Cord Socket
Main switch
Fuse
Cable collector
Quick Tip Changer
Tip Cleaning System
Process Control
Intelligent Heat Management
Equipotential connection
CONTROL UNIT
T245-A
Handpiece
USB-B connector to PC:
- Update station software
- Create graphs of the soldering process
- Manage and monitor parameters via PC
INSTALLATION
PART NAMES
5
Loosen the tightening knob to adjust the
position of the cable collector.
ADJUSTABLE STAND
CABLE COLLECTOR
The tool stand is easily adjustable. Loosen the tightening knob to adjust the position.
Slide the green piece down to place the wire.
6
CD-1BC/2BC/9BC - SOLDERING STATION
Tap smoothly the cartridge on the wiper profile to
remove the excess of solder.
Provides a deeper cleaning on the tip.
CL6205 Inox Wool
TAPPING WIPING
Full set of clean option: sponge, metal wool and brush
S0331 Sponge S0354 Sponge
Use the slots to wipe any posible particle sticked
on the tip.
More agressive on the tip than the wool.
CL6220 Brushes
The smoothest cleaning method. The sponge has to be kept wet (not soaked) using distilled water.
CLEANING OPTIONS
ø 1
ø 1,5
ø 3,5
A
B
7
Round Chisel Round
bent
Bevel Special
Cartridges
Alignment
B
C
A
Place the handpiece on top of the new
cartridge, press it slightly down and remove
the handpiece from the extractor.
Place the handpiece in the extractor and
remove the cartridge.
C245 cartridge range is the widest one of JBC
with many shapes, sizes and special models.
They are appropriate for general soldering
purposes and they are perfect for both
SMD components or for applications
with high power requirements such
as ground plane soldering.
Please visit our website to see the full range
www.jbctools.com
Press the cartridge into the opening A, B or C:
A. For straight C210 cartridges.
B. For curved C210 cartridges.
C. For C245 cartridges.
QUICK TIP CHANGER
CARTRIDGE RANGE
Important
It is essential to insert the cartridge till the
end for a good connection. Use the mark as
reference.
8
CD-1BC/2BC/9BC - SOLDERING STATION
T245-A Handpiece
These handpieces are perfect for both SMD components and for jobs with high power requirements.
Use C245 cartridge range
HANDPIECE
CONNECTABLE HANDPIECES
T210-A Precision Handpiece
For precision applications with medium power requirements.
T210-PA Precision Blue Handpiece
Used for leaded jobs.
Use C210 cartridge range.
T470-A* Handpiece with screw
It incorporates a screw for securing the cartridges.
T470-SA* Handpiece with screw + long cable (3m)
T470-A* Tri-lobed Handpiece with screw
3-sided handle for easy grip.
T470-FA* Comfort Handpiece with screw
It incorporates a foamed grip of insulating material which
makes you feel more comfortable when working
T470-MA* Comfort Handpiece
with screw + long cable (3m)
T245-PA Blue Handpiece
The blue grip allows the user to differentiate the tool
for leaded jobs from the lead-free ones.
T245-B Soft touch Handpiece
The striated appearance helps you hold the handpiece
for a long time. Use C245 cartridge range
*These handpieces only work with C245 cartridge range for this station.
F3449 Fume Extractor (not included)
Easily clips onto the handpiece and can be quickly removed
for easy maintenance.
ACCESSORIES
0
c
Selected temp.
350 oC
P ow e r 1 0%
350
Main m en u
Coun te rs
Tool s et ti ng s
Exit
1 Reset settings
2
Station settings
3
Tool settings
1
Plugged hours 0
2
Working hours 0
3
Sleep hours 0
1
Fix one temp -----
2
Temp levels set OFF
3
Sleep delay 0 min
4 Counters
5
Program version
4
Hibernation hours 0
5
No tool hours 0
6 Sleep cycles
0
4
Sleep temp 1800C
5
Hibernation delay 30 min
6
Temp adjust + O OC
Tool 245
Tool 245
BackBack
Stat io n se tt in gs
1 Temp unit
Celsius
2
Maximum temp 4000C
3
Minimum temp 2000C
4
Help text OFF
5 Beep ON
6
Change PIN
Back
9
CONTROL SCREEN
SETTINGS MENU
Tip temperature
Decrease &
move down
Increase &
move up
Access Menu &
Confirm Selection
% Instant power supplied
to the tool
Original PIN: 0105
Expected life
(hours)*
Sleep
Temp
Working
Temp
Temp (ºC)
700
600
500
400
300
200
200 225 250 275 300 325 350 375 400 425 450
100
0
10
CD-1BC/2BC/9BC - SOLDERING STATION
JBC stations intelligently manage the tool temperature and it helps to extend the tip life:
Heat management increase tip life which reduces cost of ownership.
HEAT MANAGEMENT
Work mode: Lift tool from the stand and the tool tip heats up to the selected temperature.
Sleep mode: When the tool is in the stand, the temperature reduces (preset sleep temperature is
180ºC / 360ºF).
Hibernation mode: After longer periods of inactivity (pre-set to 30 minutes), the power is cut off and
the tool cools down to room temperature.
11
MAINTENANCE
Prior to maintenance or storage you must unplug
the equipment from the power supply and let it
cool down.
- Use a damp cloth to clean the case and the tool.
Alcohol can be used only to clean the metal parts.
- Check periodically that the metal parts of the
tool/stand are clean in order to have a good
detection when the tool is in the stand.
- Clean the station’s screen with a glass cleaner
or a damp cloth.
Unplug the station. Remove the fuse by pulling
the black cap. Help yourself with a lever tool if
necessary. See the fuse’s technical specifications
on the last page.
Place the new fuse into the holder by pushing
and place it again into the station.
Clean periodically
- Keep the tip surface clean and tinned prior to storage in order to avoid tip oxidation.
Rusty and dirty surfaces reduce heat transfer to the solder joint.
- Periodically check all cables and tubes connected.
- Replace any defective or damaged handpiece or tool.
- Replace the fuse if it is blown according to the following guidelines:
REPAIR
- Repairs should be performed only by a JBC’s authorized technical service.
- JBC offers you a professional after-sales service for your equipment.
- Use original JBC spare parts only. Otherwise this may lead to accidents.
0013840-0214
TECHNICAL SPECIFICATIONS
- Temperature selection from 90°C (190°F) to 450°C (840°F) (±5%).
- Output Peak Power CD-BC: 130W.
- Safety transformer, mains separator and double isolation.
- CD-1BC 120V 50/60Hz. Input fuse: 2A. Output: 23,5V. Control Unit model: CD-1C
- CD-2BC 230V 50/60Hz. Input fuse: 1A. Output: 23,5V. Control Unit model: CD-2C
- CD-9BC 100V 50/60Hz. Input fuse: 2A. Output: 23,5V. Control Unit model: CD-9C
- Total unit weight: 2,6 Kg. (5.7lb)
- Complies with CE standards according to the following directives:
2006/95/CE, 2004/108/CE, 2011/65/EU
- ESD protected housing “skin effect”.
- Equipotential connector and the tool tip are connected to the station’s mains grounding
for ESD protection.
This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.
WARRANTY
JBC’s 2 year warranty covers this equipment against all
manufacturing defects, including the replacement of defective
parts and labour.
Warranty does not cover product wear due to use or mis-use
and shall be void if the equipment has been tampered with by
unauthorised persons.
In order for the warranty to be valid, equipment must be returned,
postage paid, to the dealer where it was purchased enclosing
this form duly filled in.
www.jbctools.com
SERIAL Nº
DEALER’S STAMP
DATE OF PURCHASE
Visit our website to see the updated manuals.
Loading...