Page 1
www.jbctools.com
Reference Guide
BD
SOLDERING
STATION
JBC stations intelligently manage the tool temperature:
Work mode: When the tool is used, pre-set work temperature is 350º C.
Sleep mode: When the tool is in the stand, the temperature goes down to 220º C.
Hibernation mode: After longer periods of inactivity (pre-set i.e 30 minutes), the power is cut off and
the tool cools down to room temperature.
The advantage of this heat management is lifespan increase which ensure low cost of ownership.
HEAT MANAGEMENT
Page 2
2
BD / SOLDERING STATION
CONTENTS
CONTROL UNIT
HANDPIECE
T210-A
CARTRIDGES
C210001
C210008
CARTRIDGES
C245003
C245007
MANUAL
POWER CORD
HANDPIECE
T245-A
MANUAL
SUPPLIED WITH
BD-2SA / BD-1SA
SUPPLIED WITH
BD-2BA / BD-1BA
www.jbctools.com
Reference Guide
BD
SOLDERING
STATION
JBC stations intelligently manage the tool temperature:
Work mode: When the tool is used, pre-set work temperature is 350º C.
Sleep mode: When the tool is in the stand, the temperature goes down to 220º C.
Hibernation mode: After longer periods of inactivity (pre-set i.e 30 minutes), the power is cut off and
the tool cools down to room temperature.
The advantage of this heat management is lifespan increase which ensure low cost of ownership.
HEAT MANAGEMENT
Page 3
CABLE COLLECTOR
Use the cable collector for
keeping workplace clear of
cable
CABLE ASSEMBLY
CARTRIDGE
EXTRACTOR
STAND
3
SETUP
Power Cord
Socket
Main switch
Equipotential
connector
CABLE POSITION
Page 4
WARRANTY
JBC’s 2 years warranty guarantees this equipment against all manufacturing defects, covering the replacement of defective parts and
all necessary labour. Warranty does not cover product wear due to use or mis-use.
In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased enclosing this
fully completed form.
SERIAL Nº
DATE OF PURCHASE
STAMP OF DEALER
press SELECT key 2
seconds to enter Menu
DEFAULT PIN: 0105
SELECT
CHANGE STATION
PARAMETERS S
Language?
ENGLISH S
Tool Select
T245/T210 S
Total Hours
00000 S
Temperature Unit
CELSIUS/FAHRENHEIT S
Fix Temp. Levels
OFF/ON S
Work Hours
00000 S
Max. T= [400oC] S
Min. T= 200oC
Sleep Dealy Time
0 MINUTES S
Sleep Hours
00000 S
Max. T= 400oC
Min. T= [ 200oC] S
Power Limit
130W S
Popup
ENABLED/DISABLED S
Sleep Temperat.
220 oC/oF S
Hibern. Hours
00000 S
Change PIN
YES/NO
Hibernation
30 MINUTES S
Sleep Cycles
00000 S
Temperat. Adjust
+/- 0 oC/oF S
Save Changes?
NO YES
Save Changes?
NO YES
CHANGE TOOL
PARAMETERS S
COUNTERS READ
S
RESET PARAMETERS
S
EXIT SETUP
S
MENU SETTINGS
0008802-0610
4
TECHNICAL SPECIFICATIONS
- Temperature selection from 90 to 450°C (±5%).
- Power: 75W.
- Safety transformer, mains separator and double isolation, with temperature protection fuse.
- BD-2BA / BD-2SA 230V control unit. Input: 230V 50Hz. Output: 24V.
- BD-1BA / BD-1SA 120V control unit. Input: 120V 60Hz. Output: 24V.
- Total weight of unit: 2,6 Kg.
- Complies with CE standards on electrical safety, electromagnetic compatibility and ESD protected housing
“skin effect”.
- RoHS compliant.
- Equipotential connector and the tool tip are connected to station mains ground supply for ESD protection.
This product should not be
thrown in the garbage.
Loading...