Page 1
Auto-Feed Iron
Ref. AL250-B
www.jbctools.com
Page 2
2
Page 3
3
Packing List
The following items should be included:
Auto-feed Iron .......................................... 1 unit
Ref. AL250-B
Allen Key 2,5mm ................................... 1 unit
Ref. 0780493
Manual
Auto-Feed Iron
Ref. AL250-B
ww w. jbctools .com
www .jbc tool s.c om
Page 4
4
Features
Stand
Ref. AL-SD
The AL250-B Auto-feed Iron is compatible only with Auto-feed Soldering station
Power
Socket
Equipotential
connection
Pedal connection
(optional)
Auto-feed Iron
Ref. AL250-B
Page 5
5
1. Loosen the cartridge screw to release it.
Place the new cartridge in the Auto-feed iron.
Alignment
Guide tube
Ref . 0002401 - Ø 0,9 - 1,1 mm
Changing cartridge
For a safe cartridge change, unplug the tool or turn the station off before following these guidelines:
2. Align the tip of the cartridge with the solder Guide tube.
Important: It is essential to insert the cartridge till the end for a good connection. Use the mark as
reference. Tighten the cartridge screw.
3. You must leave a gap of 8-10 mm between the tip and the end of the Guide tube.
4. Loosen the guide screw. Adjust the Guide tube and tighten the screw.
1
3
4
2
ww w. jbctools .com
8-10 mm
Page 6
6
C250-420 C250-401
C250-405
C250-402
C250-406
C250-403
C250-412C250-404 C250-418
C250-409 C250-410
C250-413C250-407 C250-408 C250-411 C250-414 C250-415
The AL250-B Auto-feed Iron works with C250 cartridge range. Find the model that best suits your
soldering needs in www.jbctools.com
Compatible Cartridges
Note: All the cartridges shown are actual size.
ø 0,4
ø 0,6
1,8x0,8
ø 0,8
4,8x1,5
1,2x0,7
3,2x1,5
ø 2,2
2,2 x 1
1,2x0,7
2,2x1
4,8x1,5
ø 2,2
ø 3,8
2,2x1
ø 1,7
ø 1
Page 7
7
Accessories
Fume Extractor
Ref. F4468
Support
Ref. AL-IA
Optional Guide set
Ref. 0002399 - Ø 0,4 - 0,5 mm
0002402 - Ø 0,6 - 0,8 mm
0002843 - Ø 1,1 - 1,5 mm
0013915 - Ø 1,6 - 1,8 mm
ww w. jbctools .com
Page 8
0012317-0115
Warranty
JBC’s 2 year warranty covers this equipment
against all manufacturing defects, including the
replacement of defective parts and labour.
Warranty does not cover product wear due to use
or mis-use.
In order for the warranty to be valid, equipment
must be returned, postage paid, to the dealer
where it was purchased.
This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.
Specifications
Diameter of solder wire: Ø 0,4 - 1,8 mm / 0.02 - 0.07 in
Complies with CE standards
ESD protected housing “skin effect”
www.jbctools.com
Loading...