JBA 1646SJT User Manual

Corporate Ofce: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone [phone] • FAX [phone]



Installation Instructions

and Warranty Information

1630S 86-87 Ranger/Bronco II 2.9L
1632S 88-91 Ranger/Bronco II 2.9L Auto
1632S-1 88-90 Ranger/Bronco II 2.9L Manual
1633S-1 90-94 Ranger 4.0L
1634S 95-97 Ranger/Explorer 4.0L
1646S 91-93 Ranger 3.0L/Mazda B3000

CARB EO # D-57-27

Read all instructions carefully before attempting installation.

Rev. 2 2-28-13 DSL

PerTronix© thanks you for choosing JBA HEADERS, the best fitting, highest quality header on the mar­ket. In order to realize the full potential of our good fit, please read and understand these instructions
completely prior to starting work.

Check to make sure you received the proper parts for your application. The header number will be
stamped on the engine flange. If you are unsure you have received the proper parts call before you start
work.

Be sure to work safe! Whenever you work under the vehicle be sure that it is located on level, solid
ground and is supported by adequate safety stands! Remember: Hot asphalt will not support most jack
stands!

Many factors affect the installation of headers, some of which are broken or aftermarket motor mounts,
accidents that impact the configuration of the frame, and/or the installation of different engines or after­market cylinder heads.

Attention Customers breaking in new engines: Due to the extreme heat generated during the break-in
process, the appearance of the ceramic coating may be altered in certain areas. The protection character­istics and thermal barrier properties of the coating is never compromised. It is recommended that a cast
iron manifold or old set of headers be used for this process.
Notice: The coating of these headers can be marred or scratched during installation. If the header needs
to be returned and is damaged, you will be charged for recoat.

JBA uses sealing beads on all its headers. We have found that when installed correctly, the raised bead around
each port increases the pressure exerted on the gasket directly adjacent to the port and effectively prevents leak­ing gaskets. It is normal for the flange to be raised off the cylinder head the thickness of the sealing bead. It is
important when installing the header, to install all bolts loosely, then tighten evenly to ensure the flat installation
of the flange. The torque sequence from one flange to another will vary, but generally every bolt on a header
should be first fit snug, starting from the inside of the flange working out, alternating from top to bottom so
that the bolt connects the flange to the manifold to the point where they barely touch. Second, using the same

inside-out pattern, tighten each bolt until nished. This method will help prevent leakage and will give the user

the best possible performance out of their pair of headers.

1. Place vehicle in a location where the floor is solid and flat, with adequate lighting. Do not attempt to work
on a hot engine. Heat causes metal to expand and makes removal of fasteners difficult at best. Disconnect the
battery cables from the battery. Raise the front of the vehicle to obtain adequate access to the bottom exhaust

manifold anges. Use large-base jack stands to support the vehicle. Do not rely on the jack! Block the tires to

prevent the vehicle from rolling off the jack stands.

2.Disconnect the negative battery cable from the battery.

3. Disconnect the spark plug wires by grasping and gently twisting the spark plug wire boots. Do not pull on the

wires! Brush or blow any debris, which may have collected around the manifolds or spark plugs. This will help

prevent foreign matter from entering the combustion chamber when the manifolds are removed.

4. Apply penetrating oil on all accessible fasteners and fittings before attempting to remove them.

5. Unbolt the muffler assembly from the rear of the catalytic converter. Complete removal of the muffler assem­bly is not required. However, the muffler assembly needs to be dropped to provide clearance to remove the Cata-

lytic Converter assembly. Unbolt the Catalytic Converter assembly from the Y-Pipe. Remove the Catalytic