Jazz DV152 Instruction Manual

0

JJaazzzz DDVV115522

IInnssttrruuccttiioonn MMaannuuaal

l

1

FCC Statement.

FCC part 15.21

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

FCC part 15.105

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

2

Using Your Camcorder

Turn On/Off

1. Press & hold down " " to turn
camcorder on.

2. Press "

" to turn camcorder off.

Note:

Camcorder will power off after 1 minute
if not in used.

Change Mode

Press " " to change mode between
video record, still photo capture and

playback.

Record/Capture

1. Press " " to begin video recording
or take a photo.

2. Press " " again to stop video
recording.

Note:

Insert 2 fresh

AA batteries

and SD (

or MMC

)

card to operate the

cam

era.

Change Resolution

Press " " to change resolution.

Zoom

1. Press " " to zoom in.

2. Press " " to zoom out.

Playback

1. Press " " to enter playback mode.

2. In playback mode, press " " or " " to
select another file.

3. Press " " to begin or to stop playing
video, and press " " or " " to
zoom in/out photo.

4. When zoomed in press " " or " " to
enter PAN Mode to view image

Delete

1. In playback mode, press " " and

“Delete Current?” will appear on
display screen.

2. Press " " again and “Delete All?” will

appear on display screen.

3. Press " " to confirm. Press any

other

button to cancel.

Change Batteries

1. Press “ ” switch to release the
battery cover, slide down the battery
cover to remove it.

2. Remove used batteries.

3. Reinstall two fresh AA batteries,
align “+”, “-” terminals as indicated.

4. Close the battery cover.

3

Tripod nut

SD/MMC

Card Slot

LCD Screen

Lens

Microphone
LED Light

Speaker

Appearance

USB Connector

TV Out Port

USB

ejector

Strap Holder

Battery Cover

4

Note: Please insert two fresh AA batteries and SD card to operate the camera

a) Installing Batteries and Powering ON

Press “ ” switch to release the battery cover. Slide down and remove the battery cover. Insert two new AA

alkaline batteries. Note polarity on battery terminals. Slide and close the battery cover. Press and hold down
the power switch until LCD panel shows that camera is turned ON

b) Installing SD/MMC Card

Turn your camcorder OFF before inserting / removing the SD/MMC Card (maximum 2GB)

Insert the SD Memory card into the SD/MMC Card Slot. Check card’s alignment according to

position diagram on the camera before inserting. Push it down until the card stays latched. Do not

force card during insertion – forcing may damage SD card and camera as well.
Push and release inserted card when you wish to remove or replace the card.

Note that the SD Card has a tiny LOCK switch on the side. Set the switch on the card to un-LOCK;

only this unlocked position will allow you to store recorded videos and still pictures on the SD Memory

Card.

c) Selecting Video / Still Pictures Resolution

You can select High or Low resolution for recording videos or taking still pictures.

Press " " resolution switch selecting desired resolution.

LCD screen will display “Hi” or “Lo” indicating HIGH or LOW resolution selected.