Jaypro Sports FSG67910 User Manual
FSG67910
FUTSAL GOAL
ASSEMBLY INSTRUCTIONS
3 m
118 1/8 in(
2 m
78 3/4 in(
)
)
1 m
39 3/8 in(
)
TOOLS REQUIRED:
7/32 in Allen Wrench
9/16 in Socket Wrench or Comination Wrench
Rubber Mallet
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER
CONNECTING HARDWARE AND STRUCTURAL INTEGRITY.
REPLACE DAMAGED OR MISSING HARDWARE IMMEDIATELY.
2) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
3) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
FRONT
VIEW
PHONE:
800.243.0533 (TOLL FREE)
860.447.3001 (LOCAL)
JAYPRO SPORTS, LLC, 976 HARTFORD TURNPIKE, WATERFORD, CT 06385 USA
DESCRIPTION
www.jaypro.com
SIDE
VIEW
FAX:
860.444.1779 (SALES)
860.440.0628 (ENG.)
FUTSAL GOAL CUSTOMER ASSEMBLY INSTRUCTIONS
3/25/2011
DWN BY
DONL
REV
CHKD BY
WVB
SHEET
1 5
A
OF
PART NUMBER
FSG67910
SIZE
SCALE
A
THIS DRAWING IS THE SOLE PROPERTY OF JAYPRO SPORTS INC. AND MAY
NONE
NOT BE REPRODUCED WITHOUT WRITTEN PERMISSION OR CONSENT
DATE
2
1
FSG67910 FUTSAL GOAL
ASSEMBLY INSTRUCTIONS
1) UNPACK ALL PARTS AND CHECK AGAINST PARTS LIST TO ENSURE THAT ALL PARTS
HAVE BEEN INCLUDED
2) INSPECT FOR DAMAGE. REPORT ALL DAMAGES TO TRUCKING COMPANY.
3) LAY PARTS OUT ON CLEAN DRY FLOOR AS SHOWN IN FIGURE 1
4) ASSEMBLE CORNER (ITEM 7) WITH UPRIGHT (ITEM 4) DO NOT ADD HARDWARE AT THIS
TIME. SEE DETAIL A
B B
5) INSTALL END CAP USING RUBBER MALLET TO BOTTOM BACKSTAY (ITEM 1 & 2) SEE
DETAIL B
6) ASSEMBLE THE BACKSTAY (ITEM 6) INTO THE HUB OF THE CORNER FITTING (ITEM 7)
USING 2-1/2" LONG SCREW
7) ASSEMBLE BOTTOM BACKSTAY (ITEM 1) TO ASSEMBLED CORNER AND UPRIGHT. SEE
DETAIL C, DO NOT ADD HARDWARE
8) WITH THE HELP OF A SECOND PERSON ASSEMBLE THE BACKSTAY (ITEM 6) YOU MAY
NEED TO LIFT UP ON THE BOTTOM BACKSTAY TO FIT TOGETHER. NOW ADD THE BOLTS,
WAHSERS OR NUTS AS SHOWN IN DETAILS A, C, AND D; DO NOT TIGHTEN HARDWARE
COMPLETELY YET
9) REPEAT STEPS 4, 5, 6 AND 7 TO ASSEMBLE UPRIGHT ON OPPOSITE SIDE
10) SLIDE TOP CROSSBAR (ITEM 5) INTO CORNER AND INSTALL HARDWARE SHOWN IN
DETAIL E, DO NOT TIGHTEN BOLTS COMPLETELY.
11) ASSEMBLE OPPOSITE UPRIGHT TO CROSSBAR WITH HARDWARE SHOWN IN DETAIL E
AND AGAIN DO NOT TIGHTEN BOLTS COMPLETELY
12) WITH THE HELP OF A SECOND PERSON ASSEMBLE THE SQUARE BOTTOM CROSSBAR
(ITEM 3) TO THE BOTTOM BACKSTAYS USING HARDWARE SHOWN. SEE DETAIL F AGAIN
DO NOT TIGHTEN THE HARDWARE COMPLETELY.
13) CUT AND APPLY ANTI-SKID PAD TO BOTTOM SURFACES OF UPRIGHT, BOTTOM
BACKSTAYS AND SQUARE BOTTOM CROSSBAR.
14) WITH THE HELP OF A SECOND PERSON STAND THE GOAL UP-RIGHT
15) SQUARE THE FRAME AND TIGHTEN ALL HARDWARE. START BY ALIGNING THE
CORNER PIECE WITH THE UPRIGHT EXTRUSION AND CLOSING ANY GAP BETWEEN THE
CORNER AND THE UPRIGHT. NOW TIGHTEN THE TWO SCREWS FURTHEST FROM THE
CORNER HUB. ONCE THEY ARE SECURE YOU CAN TIGHTEN THE BOLT CLOSEST TO THE
CORNER HUB. FOLLOW THIS SAME PROCEDURE FOR SECURING THE CROSSBAR TO THE
CORNER PIECE. ONCE THE CORNERS ARE SECURED THE REST OF THE GOAL
HARDWARE CAN BE TIGHTENED DOWN.
16) LAYOUT NET AND IDENTIFY CORNERS. DRAPE NET OVER OR UNDER FRAME AND
ATTACH USING VELCRO STRIPS CUT AT 12 INCHES LONG EACH AND SPACED
A A
APPROXIMATLEY 12 INCHES APART
AS AN OPTION
17) TO MINIMIZE THE AMOUNT OF SAG
ACROSS THE BACK OF THE NET, WEAVE THE
CORD (SUPPLIED WITH THE ASSEMBLY KIT)
THROUGH THE MESH AND SECURELY TIE IT
OFF ALONG THE CORNER ELBOW OF EACH
BACKSTAY.
2
PHONE:
800.243.0533 (TOLL FREE)
860.447.3001 (LOCAL)
JAYPRO SPORTS, LLC, 976 HARTFORD TURNPIKE, WATERFORD, CT 06385 USA
DESCRIPTION
FUTSAL GOAL CUSTOMER ASSEMBLY INSTRUCTIONS
PART NUMBER
FSG67910
SIZE
SCALE
A
THIS DRAWING IS THE SOLE PROPERTY OF JAYPRO SPORTS INC. AND MAY
NOT BE REPRODUCED WITHOUT WRITTEN PERMISSION OR CONSENT
N/A
DATE
www.jaypro.com
3/25/2011
1
DWN BY
DONL
REV
A
FAX:
860.444.1779 (SALES)
860.440.0628 (ENG.)
CHKD BY
WVB
SHEET
2 5
OF
Loading...