Jaypro Sports FBSC-240EB User Manual

--- FBSC-240 & FBSC-240EB ---

(OFFICIAL SOCCER / FOOTBALL GOAL)

Installation Instructions

Call Jaypro Sports Equipment at 1-800-243-0533

during regular business hours for technical support.

www.jaypro.com

Rev: A Page 1 of 8

JAYPRO SPORTS

FBSC-240 & FBSC-240EB COMBO GOAL

IMPORTANT NOTICE:

1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.

2) NEVER ALLOW ANYONE TO CLIMB OR HANG ON THE NET OR GOAL
FRAME. AS SERIOUS INJURY OR DAMAGE TO THE EQUIPMENT MAY
OCCUR.

3) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.

4) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.

TOOLS REQUIRED:

(1) Socket and / or Box Wrench Set
(1) Electric Drill with 1/4” Socket Bit or Driver
(1) Step Ladder, 12 FT
(1) Rubber Mallet

 Unpack all parts and check against parts list to ensure that all have been included.
 Inspect all parts for damage. Report any damages to the trucking company.

ITEM DESCRIPTION FBSC-240 FBSC-240EB

1 FRONT RIGHT CORNER WELDMENT 2 2
2 FRONT LEFT CORNER WELDMENT 2 2
3 4" DIA UPRIGHT EXTRUSION x 116" LONG 4 4
4 4" DIA CROSSBAR EXTRUSION x 278" LONG 2 2
5 FOOTBALL CROSSBAR x 278" LONG 2 2
6 FOOTBALL UPRIGHT x 120" LONG or 240” LONG 4 4
7 1.66" DIAMETER BACKSTAY BRACE 4 N/A
8 2-1/2" DOME CAP, AL. 4 4

9 GROUND STAKE 4 N/A
10 3/8"-16 x 3" HEX HEAD CAP SCREW ZP 8 8
11 3/8"-16 x 4-1/2" CARRIAGE BOLT, ZP 8 8
12 3/8" FLAT WASHER, SS 48 68
13 3/8"-16 THIN HEX HD LOCKNUT, ZP 20 24
14
15 1.66” DIA EUROPEAN STYLE BACKSTAY N/A 4
16 EUROPEAN BACKSTAY LOWER HUB N/A 4
17 7/8” x 5” LONG BACKING BAR N/A 4
18 3/8" MEDIUM SPLIT LOCK WASHER, ZP 16 28
19 3/8"-16 x 1 1/4" BUTTON HEAD, SS 16 28
20 3/8”-16 x 2 1/2” HX HEAD CAP SCREW, ZP 4 16
20 EC-824 (Optional if purchased) 2 2
21 NET (Optional if purchased) 2 2
22 Ground Sleeves (Optional if purchased PN: SGP-445G) 4 4

QTY (PAIR)

#8 x 3/4" HEX HEAD FLANGE SELF DRILL SCREW, ZP

8 8

Rev: A Page 2 of 8

Site prep:

1. Determine the proper location for the goal uprights on the playing field. The spacing
between uprights is 24’-4” center to center. Dig the footing holes to the dimensions as
shown on the illustration below. These are minimum suggested dimensions for
average soil conditions.

2. For best results assemble the lower goal frame; uprights and crossbar assembly on the
ground prior to placing in the footing.

6” of crush stone, block or concrete footing.

These are suggested dimensions for average soil conditions,
consult local building codes.

Semi-permanent installation: SGP-445G ground sleeve sold separately

1. Note: Whenever goal is removed from ground sleeves for maintenance or storage,
always cover the open end of the sleeve using the top cap provided.

2. Install ground sleeves as shown in drawing SGP-445G. Ground sleeves may be
installed with or without using the goal frame itself.

3. If using goal frame to install sleeve in. Slide the sleeves onto the bottom of each
upright and lower the assembled goal into the footing. Be careful to ensure that
concrete does not enter the sleeve – recommend wrapping tape around goal upright &
top of sleeve. Make sure the distance between the underside of the soccer crossbar
and the playing surface measures 8 FT. Brace the structure to assure that it doesn’t
shift during curing process.

4. Wait for the concrete to fully cure according to the manufacturer’s instructions. (A
minimum of 48 hours)

Permanent installation:

1. Lower the assembled goal (see frame assembly instructions) into the footing. Pay
special attention to proper orientation with regards to the face side. Block beneath and
around each upright, plumb the structure and pour the concrete. Check that the
distance between the playing surface and the crossbar of the upright is 8’. Brace the
structure to assure that it does not shift during the footing curing process.

2. Wait for the concrete to fully cure according to the manufacturer’s instructions. (A
minimum of 48 hours)

Rev: A Page 3 of 8