JayBird JB-BA-100I User Manual

User Manual

Bluetooth® Adapter for iPod

Bluetooth® Stereo Headset

JB-BA-100i

ENGLISH

Please review your user guide carefully

before using this product

If you need further assistance DO NOT return it to the store where you bought it, please contact us at:

1.866.244.3399

For additional troubleshooting information please visit us on the web at:

www.jaybirdgear.com

and click on “reviews & support”

ENGLISH

Introduction:

The JayBird JB-BA-100i Bluetooth® Adapter for iPod® enables any compatible iPod® (see list below) to transmit stereo audio to your JayBird JB-100 Bluetooth® Stereo Headset (up to a 33 foot range).

The JayBird Bluetooth® Adapter for iPod® is compatible with the following iPod® models:

ENGLISH

The JayBird JB-BA-100i Bluetooth® Adapter for iPod® is powered by the iPod® once connected to the iPod® dock connector, so no batteries are required.

Pairing the adapter with your JayBird Bluetooth® Stereo Headset

1. Before pairing, make sure that your headset is turned off (no ﬂashing blue LED through the right side logo).

2. Put the headset into pairing mode by pressing the POWER/TALK button on the headset for 5 seconds until the LED on the right earpiece begins blinking alternating red and blue colors.

3. Plug the adapter into the iPod your iPod®. The LED and JayBird name should be facing UP (same side as the front of the iPod®)

4. Turn the iPod respond to the streaming music by automatically searching for the JayBird JB-100 Bluetooth® Stereo Headset. The LED on the adapter will be steady blue color while it is in search mode, and then ﬂash blue once it start to pair with the headset.

5. Once the headset ﬁnds and pairs with the adapter, both the adapter and headset LEDs will blink blue (the headset will blink blue every six seconds and the adapter LED will blink blue every 2 seconds). Your headset and adapter are now paired.

on and start playing music. The adapter will activate and

dock connector located on the base of

Listening to Music

1. Once paired, the next time you connect the devices, just turn your headset on by holding the power/talk button for 3 seconds until the LED on the right earpiece ﬂashes blue, then plug the adapter to the iPod® dock connector and play music. You will hear the music through your headset.

2. Adjust the volume by using the UP/DOWN buttons on the headset. Adjusting the volume on the iPod

3. When not using the adapter, it’s a good idea to remove it from the iPod dock connector as it is drawing power from the iPod® and will reduce the iPod® battery play time.

will have no effect.

Using the phone call feature of your JayBird Bluetooth® Stereo Headset

1. The JayBird Bluetooth® Stereo Headset can also be paired with any compatible Bluetooth® enabled mobile phone. For pairing instructions, refer to the user manual that came with your headset.

For a list of compatible A2DP enabled phones please visit www.jaybirdgear.com/phones

ENGLISH

2. Once paired with a mobile phone, you can make and receive phone calls even while listening to music from your iPod® wirelessly using your JayBird Bluetooth® Adapter. When a call comes in, you will hear the phone ring. Answer the call by pressing the TALK button on the headset (or by pressing the answer button on your phone) and the music will turn off automatically and you can then take the call. When you done with the call and the call has been terminated, the headset will switch back to music play. (Refer to your JayBird Bluetooth® Stereo Headset user manual for detailed instructions on making and receiving phone calls)

Technical Speciﬁcations

Protocol

Frequency Band

Tx Power

Range

Audio Format

Music Playing Time

Battery

Charging

Weight: (Grams)

Operating Temp

Storage Temp

AC power supply

No of Paired Device

Pairing passkey

Features

Agency Approvals

Included in Box

Compatibility

1.2, A2DP

Bluetooth

2.4 GHz

Class 2

Bluetooth 10 meters/33 feet 16-bit Stereo

Draws power from iPod

No battery - draws power from iPod

No charging required - draws power from iPod

6.5g 14 F to 113 F (-10° C to 45° C)

-4 F to 131 F (-20° C to 55° C)

Not required - draws power from iPod

1 Not required - automatically pairs with headset

Power and audio line out from iPod®. Status LED FCC, CE

JayBird Bluetooth® Adapter for iPod®, User Manual

• iPod® nano 1st generation 1GB, 2GB, 4GB

5th generation (video) 30GB, 60GB, 80GB

• iPod

nano 3rd generation (video) 4GB, 8GB

• iPod

nano 2nd generation 2GB, 4GB, 8GB

• iPod

classic 80GB, 160GB

• iPod

touch 8GB, 16GB

• iPod

FRANçAIS

Veuillez passer en revue votre guide

d’utilisateur soigneusement avant

d’employer ce produit.

Si vous avez besoin davantage d’d’aide ne la renvoyez pas au magasin où vous l’avez achetée, svp nous contactent à :

1.866.244.3399

Pour l’information de dépannage additionnelle svp rendezvisitenous sur l’Internet à :

www.jaybirdgear.com

et clic sur les “revues et l’appui”

FRANçAIS

Introduction:

L’adapteur de JayBird JB-BA-100i Bluetooth® pour l’iPod permet à n’importe quel iPod® compatible (voir la liste ci-dessous) de transmettre l’acoustique stéréo à votre écouteur stéréo de JayBird JB-100 Bluetooth® (jusqu’à une gamme de 33 pieds).

L’adapteur de JayBird Bluetooth® pour l’iPod est compatible avec les modèles suivants d’iPod®:

+ 15 hidden pages