“TO BE REMOVED FOR USE BY THE OCCUPANT.”
Jason International, Inc.
8328 MacArthur Drive
North Little Rock, AR 72118
www.jasoninternational.com
OWNER’S MANUAL
IntegrityTM AirMasseur
INSTALLATION, OPERATION, AND MAINTENANCE
If the carton shows sign of damage, inspect
the product before accepting and describe the
problem on the Bill of Lading.
INSPECTION
Inspect the unit prior to installation. In the event of a problem, DO
NOT install the unit. All components are factory assembled
onto the bath and the unit is water tested and inspected prior
to leaving the factory.
The installer is responsible for inspecting the unit to insure that
it is free from defects and/or shipping damage. The factory
is not responsible for damage that might have been avoided
by inspection or testing prior to installation.
NOTE: Transportation and insurance from Jason’s factory
are the buyer’s responsibility.
Damage sustained in transit i s the responsibility of the
carrier. The owner or installer MUST open, uncrate, and
inspect the unit for damage when it is delivered. Inspect
plumbing and whirlpool surface for missing or damaged
components. Alert the dealer of any discrepancies. If damage
is discovered, immediately notify the carrier in writing and
request that they have a representative inspect the unit. If
the carrier fails to respond, report it to the seller and carrier.
49-1000-211
Date 05/08
Baths
®
Always le a freight claim promptly.
Damage to the unit during installation will not be covered
by warranty and is the responsibility of the installer. ALL
WARRANTY CLAIMS ON ACRYLIC SURFACE DAMAGE MUST BE
MADE PRIOR TO INSTALLATION.
To protect the unit from damage, keep the bath in its carton
until ready for installation.
EQUIPMENT ACCESS
In accordance with Building Codes, service and maintenance
access to all therapy bath equipment, controls, and electrical
connections must be provided during installation. Insufcient
access will hinder repair and maintenance. For the minimum
access, size refer to Table 1 - Specications. Warranty service
will not cover the cost of providing equipment access.
CAUTION: DO NOT LIFT OR HANDLE THE BATH BY ITS PLUMBING.
OWNER’S RECORD
Dealer:
Date Purchased:
Date Installed:
Installer:
Jason International, Inc. • 501.771.4477 Page 1 of 8 Customer Service : 800.255.5766
PLACE SERIAL NUMBER CARD WITH
PRODUCT CONFIGURATION IN THIS BOX
INSTALLATION INSTRUCTIONS
INSTALLATION
See the USER MAINTENANCE INSTRUCTIONS on page 5 for humidity
and mold prevention suggestions prior to Installation.
1. Finish Frame
Construct a nish frame under the bath rim to keep the
bath deck level and insure proper drainage toward the
bath well. This frame is not intended to support the full
bath weight. (See Figure 1 & Figure 2.)
NOTE: If you use a tile ange kit, modify the framing to
support the bath lip as shown in Figure 1.
Jason offers a removable lateral skirt for most baths. The
skirts are available in matching acrylic colors and provide
convenient access to the bath equipment as well as an
excellent nished appearance.
If a lateral skirt is to be used, the bath deck MUST be leveled at
20.5” from the support ooring, or the skirt will not t properly.
If a Jason lateral skirt is not used, an access panel MUST
be provided to enable nal electrical connections and
service. Refer to Table 1 - Specications for the minimum
recommended access panel size.
CAUTION: Make sure the support frame is drilled and/or notched
as needed to assure that the air actuator and air tube are not
bound or pinched.
Apply 100% Silicone with water resistant properties
between the the water-resistant backer board and the
deck of the bath.
2. Rough-in the plumbing for the drain and overow assembly. At this
time also plan for the position and mounting of the faucet
set, as well as all related plumbing. All overow drains,
ll spouts, and valves must be installed according to the
instructions in this manual. If a Jason Double Cascade
TM
is provided, refer to the included instructions and install
at this time.
3. Level the bath and remove packing board:
a. Install the bath level for proper drainage. Jason baths are
designed to be supported under the entire base of the
bath. If the oor is smooth and level, the bath’s Level-
Form™ base will provide proper drainage and support.
(See Figure 3.) Mortar is required when the suboor is
not smooth and level; when additional sound insulation
is desired; or when the bath is installed in a drop-in
application. In alcove installations, a bed of mortar may
also be recommended to aid in leveling the bath. NOTE:
Do not use sand to install or level the bath.
b. Remove the packaing board before installing the bath. The
AirMasseur
is equipped with separate bath and blower
®
support bases which are joined for shipment with a
packing board. Detach the packing board from the bath
and from underneath the blower.
4. Protect the acrylic bath surface from damage during installation
with a suitable material, i.e. cardboard and/or plastic lm.
5. Install the drain and overow assembly onto the bath according
to the instructions provided with the assemblies. Position
the bath in the general area of intended installation.
TABLE 1 - SPECIFICATIONS
Model Overall
Dimension
L x W x H (in.)
B3060 60 x 30 x 20.5 29 1 36 x 17 49.7 lbs
B3260
B3660 60 x 36 x 20.5 37 1 36 x 17 47.2 lbs
B3666 66 x 36 x 20.5 39 1 36 x 17
B3672 72 x 36 x 20.5 45 1 36 x 17 44.8 lbs
B4260 60 x 42 x 20.5 44 1 36 x 17 47.2 lbs
B4272 72 x 42 x 20.5 49 1 36 x 17 42.6 lbs
C6060 60 x 60 x 20.5 54 1 36 x 17 42.1 lbs
D3260 60 x 32 x 20.5 36 1 36 x 17 52.1 lbs
N4260 60 x 42 x 20.5 49 1 36 x 17 48.2 lbs
N4272 72 x 42 x 20.5 52 1 36 x 17 46.3 lbs
V4272 72 x 42 x 20.5 46 1 36 x 17 42.3 lbs
W4266 66 x 42 x 20.5 40 1 36 x 17
60 x 32 x 20.5 32 1 36 x 17 49.1 lbs
Operating
Capacity
GAL
Blower
120V
HP
Min. Size
Access
W x H (in.)
Floor
Loading
lbs/ft
44.4 lbs
42.6 lbs
2
Jason International, Inc. • 501.771.4477 Page 2 of 8 Customer Service : 800.255.5766
Overflow
G RO UN D - GR EE N WI RE
N EU TR AL - W H ITE W IR E
H OT - B LA CK W IR E
D ED IC AT ED
12 0V , 6 0 H z
G FC I P RO TE CT ED
S E RV IC E
AIR SWITCH
C
ONTR OL BOX
A IR SW IT CH
"D RO P LO OP "
F UL L SU PP OR T BA SE
A IR SW IT CH A CT UA TO R
INSTALLATION INSTRUCTIONS (cont.)
S IL ICO N E B EA D
T IL E
D RY WA LL
D RY WA LL
T IL E
O P TI ON AL
T IL E F LA NG E
KIT
O
P TIO NA L
IN TE GR A TE D
T ILE L IP
1 " X 2 "
S U P P O RT
F IG . 2
S C R EW
6. Secure the bottom of the blower mount so that it is level with the
bottom of the bath. Position the bath in the area of intended
installation and cut the blower support strap to allow the
blower mount to rest rmly on the oor. The bottom of the
blower mount must be secured and level with the bottom of the
bath. We recommend securing the blower with removable
fasteners for ease of servicing.
WARNING: Any modication to the equipment is not
recommended and will void the Manufacturer’s warranty.
7. A minimum ventilation opening of 2” x 4” for the blower
is required, and should be designed to draw in indoor
ambient air at a minimum of 22°C (72°F).
Figure 1
REMOTE MOUNTING OF AIR BLOWER
The Jason AirMasseur
following E.T.L. guidelines. During installation, if remote
mounting of the blower and its control box is desired, use the
following procedures:
NOTE: Do not remote mount the blower more than 15 feet away
from the air inlet of the bath. Choose a location as close as
possible to the bath to assure maximum efciency.
1. The installer is to determine the layout of the piping;
exact remote mount location; and service access before
beginning any work. Use 1.5” ABS or PVC plastic tubing.
Locate the control box with the blower in an area accessible
for servicing. NOTE: A 15 foot replacement air switch
tube can be purchased from a Jason dealer, if needed.
To insure proper functioning of the system, avoid remote
mounting in a location which requires more than six (6)
piping direction changes. A 90° direction change should
be made up of two 45° elbows for maximum efciency.
2. Disconnect the blower from the air bath plumbing by
removing the two (2) screws on the checkvalve outlet and
disconnect the short piece of ex pipe between the check
valve and the elbow by removing the two (2) screws in
the elbow.
system has been factory installed
®
Jason International, Inc. • 501.771.4477 Page 3 of 8 Customer Service : 800.255.5766
Figure2
Figure 3
3. Install the blower and checkvalve in the remote location.
The remote mount locations’ ambient air temperature
should remain at approximately 72°F for optimum air
heating. Make sure the blower is well ventilated. The
blower mount should be attached rmly to the oor. Piping
between the remote blower location and the bath can be
insulated using a minmum of 1/2” thick insulation. Attach
new piping to the elbow of the existing piping.
INSTALLATION INSTRUCTIONS (cont.)
ELECTRICAL
WARNING: Verify the electrical service to match either the 120v or
240v systems. Refer to the Blower label for voltage and frequency
requirements.
NOTE: The bath is designed for indoor use only. The electrical
equipment must not be exposed to direct or indirect water
or moisture contact. The electrical equipment must also be
protected from dust and other airborne debris before, during,
and after installation.
1, Electrical Service: A licensed electrician must provide the
electrical service protected by a dedicated GFCI (Ground
Fault Circuit Interrupter). The location of the GFCI must
be at least ve (5) feet away from the inside surface
of the bath, accessible for regular testing. USE COPPER
CONDUCTORS ONLY.
WARNING: The electrical service to the GFCI must not
be interrupted by any control device. Likewise, the
electrical service from the GFCI to the bath control should
be direct and not interrupted by a switch. Never use a
switch in conjunction with a control device. This will VOID
THE MANUFACTURER’S WARRANTY.
2. GROUNDING IS REQUIRED.
The unit should be installed by a qualied service
representative and properly grounded.
TM
3. Standard Equipment. The Integrity
comes equipped with a heated air blower, an air switch
control box, air switch tubing, and a color coordinated air
actuator. The air switch control must be plugged into a
dedicated 120v(volt), 20 A (amp), 60Hz (hertz) circuit with
a service ground. The air switch tubing must be rmly
attached to the air switch control box and to the air switch
actuator. A small bead of silicone may be added to the
air tubing connections to help prevent the tubing from
disengaging.The air switch tubing must also be installed
to allow for a “drop loop” see Figure 3 on page 3. This will
prevent any moisture from entering the air switch control
box from the tubing. Finally, the blower will plug into the
control box.
4. Control Box. The blower is pre-wired with a 36” cord with a
NEMA plug end. The air switch control box and tubing is
temporarily secured to the bath’s plumbing for shipping.
During installation the tubing must be attached to the bath’s
air switch actuator and the air switch control box. The air
switch control box should be relocated to its dedicated
circuit outlet. Connect only to a dedicated Ground Fault
Circuit Interrupter (GFCI) protected, 120v (volt), 20A (amp),
60Hz (hertz) circuit with a service ground.
DANGER — RISK OF ELECTRIC SHOCK: Connect only to
a circuit protected by a Ground Fault Circuit Interrupter
(GFCI). In the unlikely occurrence of a current imbalance
in the power conductors, the GFCI will interrupt the power
to the bath.
AirMasseur® system
ALL LOCAL AND STATE ELECTRICAL AND PLUMBING CODES MUST
BE OBSERVED. Where there are no local codes the National
Electric Code (NEC) and Uniform Plumbing Code (UPC) shall be
observed. It is the responsibility of the installer/owner to
determine specic code compliance prior to installation of
the product.
NOTE: In the Commonwealth of Massachusetts, installation
is to be done by a Massachusetts licensed plumber.
CLEANING
1. Remove all loose debris. Construction plaster or excess
grout can be removed with the use of a wooden-edged
trowel.
2. Paint or tar stains can be removed with paint thinner,
turpentine, or isopropyl alcohol (rubbing alcohol). Never
allow the cleaner to soak against the acrylic surface for long
periods of time. For general acrylic-surface cleaning, refer
to the USER MAINTENANCE INSTRUCTIONS section
on page 6. Always rinse the surface immediately following
the use of cleaners.
NOTE: Follow the manufacturers instructions for safe use
of cleaning products. If the surface becomes scratched
or dulled, it may be restored by using a quality plastic
polish, like Novus Plastic Polish No. 2 (available from
the Jason Dealer). It is always preferable to protect the
acrylic surface during installation to minimize cleanup and
prevent surface damage.
WATER TESTING
Before nishing the installation, it is recommended that the
bath be water tested and the plumbing tested for leaks.
1. Before water testing the bath, make sure that the air actuator
hose is securely engaged into the bathside air actuator
and into the controls air switch.
2. Fill and operate the bath. Close the drain and ll the bath
with water to at least ten inches below the bath deck. The
incoming water temperature should not exceed 104°F
(40°C).
3. Momentarily depress the Air Switch to start the blower.
4. Inspect the plumbing for leaks.
5. Turn the blower Off and then drain the water. The bath unit
and its plumbing are designed to drain after each use,
whether used as an AirMasseur
or as a soaking bath.
®
INSTALL SERVICE CONNECTION AT LEAST 6” ABOVE
THE SUB FLOOR. The air switch control box is intended
to be installed in a dry area and is for indoor use only.
DANGER: Do not alter the factory installed wiring. All
bu ilding mate rials a nd wiring s hould be routed
away from the blower body or other heat-producing
components of the unit.
Jason International, Inc. • 501.771.4477 Page 4 of 8 Customer Service : 800.255.5766
OPERATING INSTRUCTIONS, FEATURES, AND CONTROLS
INTRODUCTION
This manual contains all of the information needed for the
proper operation of this Jason IntegrityTM AirMasseur® bath.
The bath has been designed to provide years of relaxing
trouble-free service, provided the unit is maintained and
operated in accordance with these instructions.
WARNING: BEFORE OPERATING, REFER TO THE INSTRUCTIONS
PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS ON THE LAST PAGE OF THIS MANUAL.
Thoroughly clean and disinfect the unit as described
in the CLEANING section of the USER MAINTENANCE
INSTRUCTIONS on page 6 before its rst use and periodically
thereafter.
All Jason IntegrityTM AirMasseur® baths are pre-plumbed at
the factory with standard equipment. Standard equipment
includes a quiet 1 HP, variable-speed blower with integral
heater; 20-minute timer ; and Air switch controls with “On/
Off” and blower speed functions.
FILLING AND DRAINING
Close the drain and ll the bath with water to at least 10”
below the bath deck. The maximum recommended bathing
temperature is 104°F (40°C).
Before starting the blower, ensure that it is plugged into the
air switch control box and that the control box is plugged into
its dedicated electrical service connection.
Turn the blower Off before draining the water. The bath unit
and its plumbing are designed to drain after each use, whether
used as an AirMasseur
or a soaking bath..
®
AIR ON/OFF BUTTON
The Air On/Off button (air switch activator)
allows the user to turn the blower On and Off
and controls the blowers intensity. Momentarily
depress the Air On/Off button to start or to stop
the air blower. A timer will automatically stop
the air blower after 20 minutes of operation if
it is not stopped manually.
NOTE: If the unit fails to operate, check the breaker panel
to insure that the circuit breaker is On. Check the GFCI by
testing and resetting it. If the unit still fails to operate, refer to
the Trouble Shooting Guide section of this manual on page 6.
BLOWER SPEED
Once the blower is On, to decrease the air output, press and
hold the Air On/Off button until the desired intensity is reached,
then release the Air On/Off button. To increase the air intensity,
press and hold the Air On/Off button until the desired intensity
is reached, then release the Air On/Off button.
CONTROL BOX
The blowers Air On/Off button control box is built to plug into
the dedicated GFCI electrical circuit. A 36” powercord with
a plug end is prewired to the blower, which must be plugged
into the control box. A built-in timer shuts the blower off
20-minutes after being activated.
AUTOMATIC PURGE CYCLE
Fifteen minutes after the blower is stopped and the bath is
drained, the blower will automatically start for two (2) minutes
to purge and dry the air channel system.
BLOWER
The Jason IntegrityTM AirMasseur® system contains a variable
speed-controlled heated air blower. The blower provided is
factory tested when assembled onto the bath. The blower
must be plugged into the air switch control box, which must
be plugged into its dedicated GFCI electrical service prior
to turning it on.
Jason International, Inc. • 501.771.4477 Page 5 of 8 Customer Service : 800.255.5766
USER MAINTENANCE INSTRUCTIONS
HUMIDITY
Warning: Avoid high humidity levels in your home. Mold, mildew,
fungi, and bacteria which may be harmful to health thrive in areas with
continued high humidity levels; therefore, every precaution should
be taken to make sure your plumbing xtures including bathtubs,
therapy baths, or showers do not become a source of high humidity
due to improper installations or leaks.
To avoid having your plumbing xtures become a source of
unwanted humidity, please make sure the following steps
are taken prior to installation.
1. Make sure the area where the bathtub or shower is
installed is well vented and allows enough ventilation and
air circulation to dry the bathroom environment within a
short time after taking a bath or shower.
2. If your bath or shower unit is tiled-in, use units with an
integral tile ange or make sure a tile ange kit or a similar
mechanical barrier is installed to prevent shower spray,
splash, or overow to leak behind the bathtub.
skin. This phenomenon can be related to the use of a fan for
cooling on a hot day. While the ambient temperature does
not change, the moving air makes you feel cooler. Avoiding
this cold air sensation is among the reasons Jason avoids
placing air jets directly beneath the body. If you experience
a cool air sensation, which is most noticeable during the rst
few minutes of an air bath, simply move your body slightly
away from the closest air jets.
FLUSHING / SANITIZING
Upon start-up and not to exceed 90 days thereafter, ush the
AirMasseur® bath and plumbing system with Jason’s Bath System
Cleaner, available at Jason Dealers, or use an equivalent
cleaner. Follow the cleaning instructions below:
1. Close the bath drain.
2. Fill the bath with warm water to a level at least ten inches
below the bath deck.
3. Pour 16 ounces of Jason’s Bath System Cleaner into the
bath water.
3. Make sure the plumber properly tests the AirMasseur
before it is roughed in to make sure there are no leaks and
it is installed with proper access to bath equipment.
4. Make sure that all of the plumbing and xtures in the
bathroom are in good working order and have no leaks.
5. Do not use carpeting or other materials or furniture, which
can hold moisture, in your bathroom.
6. Use disinfectant to clean any bathroom surfaces, which
are regularly exposed to moisture.
7. Clean and disinfect humidier and dehumidiers as
recommended by the manufacturer. Replace the air lter
on the HVAC unit once a month.
8. Clean moldy surfaces as soon as any mold appears by
using a detergent/soapy solution and appropriate household
cleaner. Always use gloves during cleaning. Dispose of
any sponges or rags used to clean mold.
bath
®
CLEANING
With minimum care, this acrylic-surfaced bath will retain its
high-luster nish for many years. For regular cleaning use
Jason Bath Cleaner or a mild NONABRASIVE liquid detergent
solution (i.e. glass cleaner) and a soft, wet cloth or sponge.
Do not run the air system with foaming cleaners or soaps.
Rinse the bath thoroughly after cleaning.
AIR HEATER AND AIR TEMPERATURE
The air heater incorporated into the air blower is designed
to preheat the incoming air to body temperature, not to heat
the bath water. The air heater automatically turns on when
the air blower is activated.
Even through all Jason IntegrityTM AirMasseur
preheated air, occasionally some people with sensitive skin
might experience a cold air sensation. This sensation is caused
by the swiftly moving heated air bubbles blowing on the wet
baths provide
®
4. Turn on the blower for 10 minutes.
5. Turn off the blower and drain the bath.
6. To rinse, rell the bath with cold water, turn on the blower
for ve minutes, then turn off the blower and drain the
bath.
Note: The bath can be sanitized after each bather without
harming the AirMasseur
bath plumbing.
®
ACRYLIC SURFACE MAINTENANCE
Areas with minor scratches or dull surfaces can be
restored by applying commercially available plastic polish
(i.e. Novus Plastic Polish No. 2, available at your Jason
dealer), followed by an application of acrylic paste wax. Buff
the surface with a clean soft cloth.
CAUTION: Do not use sandpaper, steelwool, or abrasive rubbing
compounds.
If scratches are too deep to rub out, or if the damage
penetrates the acrylic surface, consult the dealer for
recommendations on surface repair.
PLUMBING OR ELECTRICAL REPAIR
Refer all plumbing or electrical repair to a qualied service
technician. DO NOT ATTEMPT TO RESOLVE THE PROBLEM.
Attempts to repair plumbing or electrical equipment by a non-
qualied service technician can result in danger of electrical
shock or damage to the unit and will VOID THE WARRANTY.
When contacting the dealer or service representative, always
have the serial number, proof of purchase, and model number
available. This will insure a quick response on warranty
items. The serial number can be found on the front page of
this manual or on the small card adhered to the back of the
bath just above the blower. ALL WARRANTY REPAIRS MUST BE
AUTHORIZED BY THE MANUFACTURER BEFORE WORK IS STARTED.
Jason International, Inc. • 501.771.4477 Page 6 of 8 Customer Service : 800.255.5766
TROUBLESHOOTING GUIDE
If the unit is within the warranty period, contact Jason Customer Service: 1-800-255-5766 with the bath’s Product and Serial
numbers before work is started. The serial number can be found on the front page of this manual or on the small card
adhered to the back of the bath just above the pump.
ALL WARRANTY REPAIRS MUST BE AUTHORIZED BY JASON INTERNATIONAL BEFORE WORK IS STARTED.
FOR SERVICE, ALWAYS CONTACT THE DEALER OR AUTHORIZED SERVICE CENTER.
WARNING: Always turn off power at the main electrical service panel before servicing the bath.
AirMasseur® Bath
SYMPTOMS POSSIBLE CAUSES RECOMMENDED ACTION
a) No power to air bath unit. a) Reset circuit breakers and GFCI if it fails
to trip. Check fuses and replace if bad.
Air bath system won’t
operate.
b) Blower motor or control box is not
plugged in.
c) Air button (air actuator switch)
plastic air tube disconnected or
b) Make sure the control box and blower
motor plugs are fully inserted into their
outlets.
c) Check, reconnect, or replace tubing as
necessary.
broken.
Blower shuts off by itself or
before time elapses.
a) Blower motor overheated
and thermal protection device
deactivated motor (possibly low
voltage).
a) Check that the blower has sufcient
ventilation, and that the intake to the
blower is not blocked. Clear and allow
the motor to cool down. (Check service and
wire size.)
b) GFCI tripped. b) Contact installer/dealer.
a) Defective breaker. a) Change out the breaker.
Circuit breaker trips
repeatedly.
b) Short circuit between bath and
breaker box.
c) Other items are connected to the
b) Contact installer/dealer.
c) Contact installer/dealer.
same circuit.
Blower does not manually
shut off.
a) Defective blower control. a) Contact installer/dealer. Replace blower
control. NOTE: Blower will not manually
shut off during the two-minute purge
cycle.
WARRANTY REGISTRATION: Register your product's warranty online at www.jasoninternational.com.
The Company warrants the products of its own manufacture to be free from defects in
workmanship and material for a period of twelve (12) months from date of installation or
eighteen (18) months from date of manufacture, whichever comes rst. Any merchandise
which upon Company examination proves to be defective under normal use and service
during the warranty period will be at the Company’s option repaired, replaced or credit
issued in the amount of the invoice value of the defective merchandise. All other types
of remedies are excluded. This warranty extends only to the owner of the originally
installed merchandise. The Company is not responsible for labor or other installation
costs for the repair or replacement of defective merchandise. Company reserves the
right to substitute new or improved equipment on any replacements. The repair or
replacement of equipment shall be F.O.B. point of shipment.
This warranty shall not apply to any merchandise which has been subject to accident,
alteration, abuse, misuse, abrasives, corrosion and/or electrolysis, improper voltage
supply, misapplication, careless handling, improper installation, maintenance, abnormal
chemical conditions, nor does this warranty cover stains, discoloration or the fading of
color due to improper use of chemicals or improperly maintained water chemistry.
This warranty shall not apply to any merchandise or parts thereof which were not manufactured by Company. Such product or merchandise manufactured by others shall have
only such warranties, in writing, that may be extended and in force at the time by such
other manufacturer or supplier.
Jason International, Inc. • 501.771.4477 Page 7 of 8 Customer Service : 800.255.5766
JASON INTERNATIONAL INC. LIMITED WARRANTY
To obtain warranty service, you must contact the retailer from which the merchandise
was purchased or Company’s distributor in your area. Written notice of warranty defects
must be given to the company within thirty (30) days from the occurrence thereof. Written
permission must be obtained by the retailer or distributor from the Company before any
equipment claimed defective is returned for inspection.
EXCEPT AS PROVIDED HEREIN, COMPANY MAKES NO WARRANTIES EITHER
EXPRESSED OR IMPLIED, AS TO ANY MATTER WHATSOEVER INCLUDING THE
CONDITION OF THE MERCHANDISE, ITS MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. ANY WARRANTIES IMPLIED BY LAW AND NOT EFFECTIVELY EXCLUDED BY THIS WARRANTY, ARE LIMITED TO THE DURATION
AND REMEDIES OF THIS WARRANTY. IN NO EVENT SHALL THE COMPANY BE
LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damages, so the above limitations
may not apply to you.
This warranty gives you specic legal rights and you may also have other rights that
vary from state to state.
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS.
WARNING: When using this unit, basic precautions should always be followed, including
the following:
This manual contains information and instructions for proper operation and maintenance of your AirMasseur® bath. Failure
to follow these instructions could result in personal injury, electrical shock, or re.
READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
DANGER: TO REDUCE THE RISK OF INJURY FOLLOW THESE PRECAUTIONS:
A. Do not permit children to use this product unless they are closely supervised at all times.
B. Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the
manufacturer.
C. The water in an AirMasseur® bath should never exceed 40°C (104°F). Water temperatures between 38°C (100°F)
and 40°C (104°F) are considered safe for a healthy adult. Use time should be limited to approximately 30 minutes, followed
by a shower to cool down. Longer exposures may result in hyperthermia. The symptoms of this condition are nausea,
dizziness, and fainting, and it can be fatal. Lower water temperatures are recommended for extended use (exceeding
10 -15 minutes) and for young children.
D. Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy,
pregnant or possibly pregnant women should limit AirMasseur® water temperatures to 38°C (100°F).
E. The use of drugs or alcoholic beverages before or during AirMasseur® use may lead to unconsciousness with the
possibility of drowning. Never use the AirMasseur® bath while under the inuence of alcohol, anticoagulants, stimulants,
antihistamines, vasoconstrictors, vasodilators, hypnotics, narcotics, or tranquilizers.
F. Persons with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes
should consult a physician before using an AirMasseur® bath.
G. Persons using medication should consult a physician before using an AirMasseur® bath since some medication may
induce drowsiness while other medications may affect heart rate, blood pressure, and circulation.
DANGER: To reduce the risk of injury, enter and exit the bath slowly.
WARNING: Never operate electrically connected devices in or near the bath. Never drop or insert any object into any
opening.
This unit must be connected to a supply circuit that is protected by a GFCI. Such a device should be installed by a licensed
electrician and should be tested on a regular basis (at least monthly). To test the GFCI push the TEST button. The GFCI
should interrupt the power. Push the RESET button and the power should be restored. If the GFCI fails to operate in this
manner, there is the possibility of an electric shock. DO NOT USE. Disconnect the unit and have the problem corrected by a
qualied service technician.
To avoid the possibility of personal injury and discoloration of the acrylic surface, the inlet water temperature should not
exceed 40°C (104°F). The bath should be drained after each use. Each bather should start their bath with fresh water. Do
not use oil base additives in your whirlpool bath.
CAUTION: Do not use harsh abrasives or solvents for cleaning this unit.
INSTALLER/OWNER BEARS ALL RESPONSIBILITY TO COMPLY WITH ALL STATE
AND LOCAL CODES WHEN INSTALLING THIS PRODUCT.
SAVE THESE INSTRUCTIONS
Jason InternatIonal, Inc.
8328 MacArthur Drive • North Little Rock • Arkansas • 72118
www.jasoninternational.com
Jason International, Inc. • 501.771.4477 Page 8 of 8 Customer Service : 800.255.5766
Loading...