Jasco RM24933 User Manual

Universal
Remote Control
RM24933
INSTRUCTION
MANUAL
Table Of Contents
Button Description 1-2 Battery Installation 2 Programming for TV 4 Programming for VCR 5 Programming for Cable Box or Satellite 6 DVD or AUX Button 7 Code Search 8 Retrieving Codes 9 Television Menu Function 10-11 DBS Menu Function 12-13 Sleep Feature 14 Trouble Shooting 15-16 Warranty 16 Instructions in Spanish 17-31
Button Description
INDICATOR LIGHT The Indicator Light flashes to show that the remote is working.
ON•OFF The ON•OFF button operates the same as your original remote (note: some RCA, GE and ProScan models require you to press the device key to turn the device on and the ON•OFF key to turn the device off).
SETUP Used to program the remote or to search through codes.
TV, VCR, DVD•AUX, CBL•SAT
The TV, VCR, DVD•AUX and CBL•SAT but tons are used to select the device you want to control.
REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE
The REVERSE, PLAY, FORWARD, RECORD, STOP and PAUSE buttons operate the same as on your original VCR remote. You must press the RECORD button twice to begin recording. Buttons also control similar func tions for DVD and CD players.
TV•VCR The TV•VCR button operates the TV•VCR function of your VCR.
-
-
1
ENTER The ENTER button is used to complete channel selection for some brands of TV. It is also used to complete the code entry process.
VOL & CHAN The VOL (Volume) and CH (Channel) buttons increase or decrease channel numbers or volume.
MUTE To MUTE the volume on the TV.
PREV CH PREV CH allows you to go to the previous channel you selected. Operates the same as Last Channel, Go Back or Recall button on your original remote.
0-9 The number buttons operate the same as on your original remote, and are used for enter ing device codes or channel numbers.
MENU The MENU button calls up the TV and DBS set up menus.
-
Battery Installation
Your Universal Remote requires two (2) new AAA alkaline batteries. To install the batteries:
1. On the back of the remote, push and slide the cover off.
2. Match the batteries to the + and
- marks inside the battery case, then insert the batteries.
3. Press and slide the battery cover back into place.
Note: Programmed codes will remain in memory for a short period of time allow­ing for battery replacement. If batteries have been dead for a prolonged period of time, reprogramming may be required.
2
Button Description
3
Programming For TV
1. Manually turn on the TV.
2. Press and hold the
SETUP button until the INDICATOR LIGHT
lights, then release the SETUP button.
3. Press and release the
TV button (the INDICATOR LIGHT will blink then remain lit).
4. Find the three digit
code for your TV in the TV code list, and enter it using the Number Buttons. After your code is entered, the INDICATOR LIGHT will turn off.
5. Aim the remote at your
TV and press the ON•OFF button. Your TV should turn off.
Note: If your TV does not respond, try all the codes for your brand. If the codes do not work, or your brand is not listed, try the Code Search method on page 8.
6. With your TV on, press
CH+. If the TV responds, no further program-
ming is required.
7. Enter your code here
for easy reference.
4
Programming For VCR
1. Manually turn
on the VCR.
2. Press and hold
the SETUP button until the INDICATOR LIGHT lights, then release the SETUP button.
3. Press and release
the VCR button (the INDICATOR LIGHT will blink then remain lit).
4. Find the three digit
code for your VCR in the code list and enter it using the Number Buttons. After your code is entered, the INDICATOR LIGHT will turn off.
5. Aim the remote at
your VCR and press the ON•OFF button. Your VCR should turn off.
Note: If your VCR does not respond, try all the codes for your brand. If the codes do not work, or your brand is not listed, try the Code Search method on page 8.
6. With your VCR on,
press CH+. If the VCR responds, no further programming is required.
7. Enter your code
here for easy reference.
5
Programming For Cable Box or Satellite Receiver
The CBL • SAT button is defaulted to RCA/ GE/ProScan DBS systems, however other DBS systems can be programmed to this button.
1. Manually turn on
the Cable Box.
2. Press and hold the
SETUP button until the INDICATOR LIGHT lights, then release the SETUP button.
3. Press and release
the CABLE button (the INDICATOR LIGHT will blink then remain lit).
4. Find the three digit
code for your Cable Box or Satellite Receiver
in the code list
and enter it using the Number Buttons.
After your code is
entered, the INDICATOR LIGHT will turn off.
5. Aim the remote at
your Cable Box or satellite receiver and press the ON•OFF button. Your Cable Box should turn off.
Note: If your Cable Box does not respond, try all the codes for your brand. If the codes do not work, or your brand is not listed, try the Code Search method on page 8.
6. With your Cable Box
on, press CH+. If the Cable Box or satellite
receiver responds,
no further program-
ming is required.
7. Enter your code here
for easy reference.
6
The DVD•AUX Button
The DVD•AUX button can be used for a DVD player. It can also be assigned to any other type of device (another TV, VCR, DVD, CD Player, or audio receiver).
1. Manually turn on the
the device you wish to assign to the DVD•AUX button (TV, VCR or Cable Box or DVD Player).
2. Press and hold the
SETUP button until the INDICATOR LIGHT
lights, then release the SETUP button.
3. Press and release the
DVD•AUX button. The INDICATOR LIGHT will blink.
4. Find the three digit code
for the device you wish to program in the code list
Enter the code using the
Number Buttons.
After your code is
entered, the INDICATOR LIGHT will turn off.
5. Aim the remote at your
device and press the ON•OFF button. Your device should turn off.
Note: If your device does not respond, try all the codes for your brand. If the codes do not work, or your brand is not listed, try the Code Search method on page 8.
6. With your device on,
press CH+. If the device responds, no further program­ ming is required.
7. Enter your code here
for easy reference.
7
Programming With Code Search
If your TV, VCR, DVD.CD player, satel­lite receiver, or Cable Box does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following the steps below.
1. Turn on the device
you wish to program.
2. Press and hold SETUP
until the INDICATOR LIGHT lights, then release SETUP.
3. Press and release the
device button for the device you are programming. The INDICATOR LIGHT will blink once then remain lit.
4. Press and release
ON•OFF until your device turns off.
Important: You may have to press ON•OFF up to 200 times.
5. When your device
turns off, press the ENTER button, the INDICATOR LIGHT will go off.
8
Retrieving Codes
If you need to find the three-digit code for your TV, VCR, DBS Receiver, or Cable Box after your device is set-up using Code Search, use this procedure.
1. Press and hold SETUP
until the INDICATOR LIGHT lights, then release SETUP.
2. Press and release the
device button for the device’s code you are retrieving . The INDICATOR LIGHT will blink once then remain lit.
3. Press and release
SETUP. The INDICATOR LIGHT
will turn off.
4. Starting with 0 on the
keypad, press the number buttons in order (0-9) until the INDICATOR LIGHT blinks.
5. The number which
causes the INDICATOR
LIGHT to blink is the
first digit of your code.
6. Repeat step 4 until you
have retrieved all three
numbers in the code.
9
Television Menu Function
The TV Menu is used to make changes in the TV settings such as setting color, channels, timers, etc.
Entering the TV Menu Mode:
1. Push the TV button
on the remote.
2. Push the MENU button. This puts the remote in
TV Menu Mode. The TV Menu should now be visible on the television. The INDICATOR LIGHT will blink continuously to indicate the remote is now in TV Menu Mode.
While in TV MENU these buttons will function as follows:
VOL UP/DOWN buttons will operate as CURSOR RIGHT/LEFT
CH+/- keys will operate as CURSOR UP/DOWN.
For RCA, GE, and ProScan TVs, pushing the MENU button will select the highlighted item. The numeric buttons may also be used to select the MENU choice. Note: Not all functions in competitive models and brands of televisions may be fully supported.
10
Exiting the TV Menu Mode:
To exit the Menu Mode
and clear the TV screen push the TV button on the remote. The INDICATOR LIGHT should go out indicating the remote is now out of TV Menu Mode and will revert to it’s normal mode of operation.
Note: The remote will automatically exit the TV Menu Mode after 10 sec
­onds of inactivity with no buttons being pushed.
Special Notes:
1. Because of the wide variety of menu formats, some experimenting may be required.
2. SONY: Pressing the ENTER button while in menu mode returns to previ
-
ous menu.
3. ZENITH: Push the menu button a second time to move from the SET-UP MENU to the VIDEO MENU.
11
DBS Menu Function
The DBS Menu is used to navigate thru the Guide screens, to make changes in the DBS settings such as channel lists, passwords, etc.
Entering the DBS Menu Mode:
1. Push the CBL•SAT button on the remote.
2. Push the MENU button. This puts the remote in
DBS Menu Mode. The DBS Menu should now be visible on the television. The INDICATOR LIGHT will blink continuously to indicate the remote is now in DBS Menu Mode.
While in DBS MENU these buttons will function as follows:
VOL UP/DOWN buttons will operate as CURSOR RIGHT/LEFT
CH+/- keys will operate as CURSOR UP/DOWN.
For RCA, GE, and ProScan DBS Systems, pushing the MENU button will select the highlighted item. The numeric buttons may also be used to select the MENU choice.
Note: Not all functions in competitive models and brands of DBS systems may be fully supported.
12
Exiting the DBS Menu Mode:
To exit the Menu Mode
and clear the TV screen push the CBL•SAT button on the remote. The INDICATOR LIGHT should go out indicating the remote is now out of DBS Menu Mode and will revert to it’s normal mode of operation.
Note: The remote will automatically exit the CBL•SAT Menu Mode after 10 seconds of inactivity with no buttons being pushed.
Special Notes:
1. Because of the wide variety of menu formats, some experimenting may be required.
2. SONY: Pressing the ENTER button while in menu mode returns to previ
-
ous menu.
13
Sleep Feature
This feature will turn off your TV at the time you choose from 1 to 99 minutes.
To program Sleep Feature:
1. Press and hold
the SLEEP but ton. INDICATOR LIGHT will stay lit. Release the SLEEP button.
2. Enter time in
minutes using the numeri cal key pad. (Minutes 1 thru 9: press 0 before the actual num ber) (Maximum: 99 minutes)
3. Leave remote aimed at television.
(Sleep Feature will not work unless remote is left aimed at television.)
To turn off the Sleep Timer:
Sleep timer program will be can
celled and reset to zero be wither of the following: Press and hold SLEEP button until INDICATOR LIGHT blinks or press ON•OFF button, turning TV
OFF.
-
-
-
-
14
Trouble Shooting
Problem
Indicator light not blinking when you press any key
The remote does not operate your device
Not performing commands properly
Problems programming a TV/VCR Combo Unit
VCR not recording
Channel up and down do not function on an RCA TV
Solution
A) Replace the batteries
(with fresh, new AAA Alkaline batteries).
B) Check that batteries are
properly installed.
A) Try all the codes listed
for your brand.
B) Try the Code Search
method (page 8).
Start Code Search over again to locate the proper code.
Try the VCR code for your brand. Some combo units, however, may require both a TV and a VCR code for full operation.
As a safety feature on your remote, you must press the REC button twice.
Due to some designs, the original remote will only perform these functions.
Problems chang ing channels
No response after pressing a key
If your original remote
­required ENTER after a chan
nel, press ENTER after you select a channel.
A) Make sure you have
new batteries, and you
are aiming your remote at your devices. B) Check that batteries are
properly installed. See
page 2.
15
-
Sleep feature does not work
Reprogramming may be required after batteries are removed.
Remote must remain aimed at television after sleep is set in order for it to work.
90 Day Limited Warranty
Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied. Some states do not allow limita tions on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. If unit should prove defective within the war ranty period, return prepaid with dated proof of purchase to:
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK. 73114
-
-
16
Óndice
La Descripción Del Botón 17-18 Instalación De la Batería 18 Programación para la Televisor 20 Programación para el VCR 21 Programación para la Caja Del Cable 22 El Botón de SAT•AUX 23 Programación con Búsqueda del Código 24 Extraer Códigos 25 Función Del Menú De la Televisión 26-27 Función Del Menú De la DBS 28-29 Característica Del Sueño 29-30 Localización de Averías 30-31 Garantia Limitada de Noventa 31
Descripción De Botón
La Luz de Indicador La luz de indicador contellea para mostrar que el remoto está funcionando.
ON•OFF
El botón de ON•OFF funciona igual que su remoto original (nota: algunos modelos de RCA, de la GE y de ProScan requiérale pre sionar el clave del dispositivo para dar vuelta el dispositivo encendido y el clave ON•OFF para dar vuelta al dispositivo apagado).
Buscar Para Códigos
Para programar el remoto o para buscar con códigos.
TV, VCR, DVD•AUX, CBL•SAT
Los botones de TV, VCR, DVD•AUX, CBL•SAT se utilizan para seleccionar el dispositivo que usted desea controlar.
REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE
Los botones de REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE funcionan igual que en su remoto original del VCR. Usted debe presionar el botón "RECORD" dos veces para empiezar un grabación.
TV•VCR
El botón de TV•VCR funciona la función de TV•VCR de su VCR.
17
-
ENTER
El botón de "ENTER" se utiliza para terminar la selección de canal para algunas marcas de la TV. También se utiliza para terminar el proceso de la entrada del código.
VOL & CHAN
Las flechas VOL (volumen) y CH (del canal) aumente o disminuya los números de canal o volumen.
MUTE
Para apagar el volumen en la TV.
PREV CH
El canal anterior permite que usted vaya al canal anterior que usted seleccionó. Funciona igual que acanalan, van por último botón detrás o de memoria en su remoto original.
0-9
Los botones del número funcionan igual que en su telecontrol original, y se utilizan para entrar en códigos de dispositivo o los números de canal.
MENU El botón del MENU llama encima de las menús. TV y de DBS fijado.
SLEEP
El botón del SLEEP permite que usted fije una época de dar vuelta apagado a la TV automáti camente.
-
Instalación De la Batería
Su remoto universal requiere dos (2) acumula­dores alcalinos nuevos del AAA. Para instalar las baterías:
1. En la parte posteriora del remoto, empuje y res bale la cubierta apagado.
2. Corresponda con las baterías a las marcas + y -dentro de la caja de la batería, entonces insertan las baterías.
3. Presione y resbale la cubierta de la batería nue vamente dentro de lugar. Nota: Seguirá habiendo los códigos programa dos en la memoria por un período de la hora corto permitiendo para el reemplazo de la bat ería. Si las baterías han sido muertas por un período del tiempo prolongado, la reprogram ación puede ser requerida.
18
-
-
-
Descripción de Botón
19
Programación para la Televisor
1. Gire manualmente la prensa de la TV
2. Presione y sostenga el botón de SETUP hasta que las luces de INDICATOR LIGHT, después suelta el botón de la SETUP.
3. Presione y soltar el botón de la TV (sigue habiendo INDICATOR LIGHT entonces centelleo se encendió).
4. Encuentre el código de tres cifras para su TV en la lista de código de la TV e incorpórelo que usa los botones del número. Después de que se introduzca su código, INDICATOR LIGHT dará vuelta apagado.
5. Apunte el remoto a su TV y presione el botón de ON•OFF. Su TV debe dar vuelta apagado.
Nota: Si no responde su TV, intente todos los códigos para su marca. Si los códigos no traba jan, o su marca no se enumera, intente el método de la búsqueda del código en la paginación 24.
6. Con su TV encendido, presione CH+. Si responde la TV, se requiere la programación no adicional.
7. Introduzca su código aquí para la referencia fácil
.
20
-
Programación para el VCR
1. Gire manualmente la prensa del VCR.
2. Presione y sostenga el botón de SETUP hasta que las luces INDICATOR LIGHT, después suelta el botón de SETUP.
3. Presione y soltar el botón del VCR (sigue habiendo INDICATOR LIGHT entonces centelleo se encendió).
4. Encuentre el código de tres cifras para su VCR en la lista de código e incorpórelo que usa los botones del número. Después de que se introduzca su código, INDICATOR LIGHT dará vuelta apagado.
5. Apunte el remoto a su VCR y presione el botón de ON•OFF. Su VCR debe dar vuelta apagado.
Nota: Si no responde su VCR, intente todos los códigos para su marca. Si los códigos no trabajan, o su marca no se enumera, intente el método de la búsqueda del código en la pagi nación 24.
6. Con su VCR encendido,
presione CH+. Si responde el VCR, se requiere la programación no adicional.
7. Introduzca su código
21
-
aquí para la referencia fácil.
Programación para la Caja Del Cable
El botón de CBL•SAT se omite los sistemas de RCA/ GE/Proscan DBS, sin embargo,otros sistemas de DBS se pueden programar a este botón.
1. Gire manualmente
La caja del cable.
2. Presione y sostenga
el botón de SETUP hasta que las luces de INDICATOR LIGHT, después suelta el botón de SETUP.
3. Presione y soltar el
botón del CABLE (sigue habiendo INDICATOR LIGHT entonces centelleo seencendió).
4. Encuentre el código
de tres cifras para su caja del cable en la lista de código e incorpórelo que usalos botones del número. Después de que se introduzca su código, INDICATOR LIGHT dará vuelta apagado.
5. Apunte el remoto a
su caja del cable/receiver de satellite y presione
el botón de ON•OFF. Su caja del cable debe dar vuelta apagado.
Nota: Si no responde su caja del cable/receiver de satellite, intente todos los códigos para su marca. Si los códigos no trabajan, o su marca no se enumera, intente el método de la búsqueda del código en la paginación 24.
6. Con su caja del cable
encendido, presione CH+. Si responde la caja del cable receiver de satellite, se requiere la programación
22
no adicional.
7. Introduzca su código
aquí para la referencia fácil.
El Botón de DVD•AUX
El botón de DVD•AUX omite los sistemas de RCA/ GE/ProScan DBS. El botón de DVD•AUX permite que usted asigne otra TV, VCR, o caja del cable. To asigna otro dispositivo al botón de DVD•AUX:
1. Gire manualmente
el dispositivo que usted desea asignar al botón de DVD•AUX (caja de la TV, del VCR o del cable o sistema de DBS).
2. Presione y sostenga
el botón de SETUP hasta que las luces de INDICATOR LIGHT, después suelta el botón de SETUP.
3. Presione y soltar el botón
de DVD•AUX. La luz de indicador centelleo.
4. Encuentre el código de
tres cifras para el dispositivo que usted desea programar en la lista de código. Entra el código usando los botones del número. Despues que se introduce su código, INDICATOR LIGHT dará vuelta apagado.
5. Apunte el telecontrol a
su dispositivo y presione el botón de ON•OFF. Su dispositivo debe dar vuelta apagado.
Nota: Si no responde su dispositivo, intente todos los códigos para su marca de fábrica. Si los códigos no trabajan, o su marca no se enumera, intente el método de la búsqueda del código en la paginación
24.
6. Con su dispositivo
encendido, presione CH+. +. Si responde la caja del cable, se requiere la programación no adicional.
23
7. Introduzca su código
aquí para la referencia fácil.
Programación con Búsqueda del Código
El botón de DVD•AUX se puede utilizar para un jugador de DVD. Puede también ser asignado a cualquier otro tipo de dispositivo (otra TV, VCR, DVD, jugador de CD, o receptor audio)..
1. Gire el dispositivo
que usted desea programar.
2. Presione y sostenga
SETUP hasta que las luces de INDICATOR LIGHT después suelta SETUP.
3. Presione y soltar
el botón del dispositivo para el dispositivo que usted está programando. Una vez entonces sigue habiendo INDICATOR LIGHT centelleo se encendió.
4. Presione y soltar
ON•OFF hasta su dispositivo da vuelta apagado.
Importante: Usted puede tener que pre sionar ON•OFF hasta 200 veces.
5. Cuando su dispositivo
da vuelta apagado, presione el botón ENTER, la luz de Indicador se apagará.
24
-
Extraer Códigos
Si usted necesita encontrar el código tridigi­tal para su caja de la TV, del VCR o del cable después de que su dispositivo set-up usando CODE SEARCH, utilice este procedimiento.
1. Presione y sostenga
SETUP hasta que las luces de INDICATOR LIGHT, después suelta SETUP.
2. Presione y soltar el
botón del dispositivo para el código de dispositivo que usted está extrayendo. Una vez entonces sigue habiendo INDICATOR LIGHT centelleo se encendió.
3. Presione y soltar SETUP
hasta que INDICATOR LIGHT dará vuelta apagado.
4. Comenzando con 0 en
el telclado numérico, presione los botones del número en la orden (0-9)hasta que INDICATOR LIGHT centelleo.
5. El número que hace INDICATOR LIGHT cen telleo es el primer dígito de su código.
6. Relance el paso de progresión 4 hasta que usted ha extraído los tres números en el código.
25
-
Función Del Menú De la Televisión
El menú de la TV se utiliza para realizar cambios en las configuraciones de la TV tales como fijar color, los canales, los temporizadores, el etc.
Entrar en el modo del mede la TV:
1. Empuje el botón de la
TV en el telecontrol.
2. Empuje el botón del
MENU. Esto pone el telecontrol en modo del menú de la TV. El menú de la TV debe ahora ser visible en la televisión. La luz de Indicador centelleo continuamente para indicar que el telecontrol ahora está en modo del menú de la TV.
Mientras que en MENU de la TV estos botones funcionarán como sigue:
Los botones VOL UP/DOWN ascendente o los botones funcionará como CURSOR RIGHT/LEFT
CH+ / - los claves funcionarán como CURSOR UP/DOWN
Para RCA, la GE, y ProScan TVs, empujando el botón del MENU seleccionarán el item destacado. Los botones numeric se pueden también utilizar para seleccionar la opción del MENU.
Nota: No todas las funciones en modelos
26
competitivos y las marcas de televisiones pueden serutilizadas completamente.
Dar salida al modo del menú de la TV:
Para salir del modo y del claro del menú la pantalla de la TV empuja el botón de la TV en el remoto. La luz de Indicador debe salir indicando que el remoto ahora está fuera de modo del menú de la TV y que invertirá
al
modo de operación.
Nota: El remoto dará salida automáticamente al modo del menu de la TV después de 10 segundos de inactividad sin los botones que son empujados. Notas Especiales:
1. Debido a la variedad
amplia de formatos del menú, algunos que experimentan pueden ser requeridos.
2. SONY : Presionar el botón mientras
que en menú el modo vuelve al menú anterior.
3. ZENITH: Empuje el botón del menú
una segunda vez de moverse desde el " MENÚ de la DISPOSICIÓN " al " MENÚ VIDEO ".
27
Función Del Menú De la DBS
Entrar en el modo del mede la DBS:
1. Empuje el botón
de la CBL•SAT en el telecontrol.
2. Empuje el botón
del MENU. Esto pone el telecontrol en modo del menú de la DBS. El menú de la DBS debe ahora ser visible en la televisión. La luz de Indicador centelleo continuamente para indicar que el telecontrol ahora está en modo del menú de la DBS.
Mientras que en MENU de la DBS estos botones funcionarán como sigue:
Los botones VOL UP/DOWN ascendente o los botones funcionará como CURSOR RIGHT/LEFT
CH+ / - los claves funcionarán como CURSOR UP/DOWN
Para RCA, la GE, y ProScan TVs, empujando el botón del MENU seleccionarán el item destacado. Los botones numeric se pueden también utilizar para seleccionar la opción del MENU.
Nota: No todas las funciones
28
en modelos competitivos y las marcas de televisiones pueden serutilizadas completamente.
Dar salida al modo el menú de la DBS:
Para salir del modo y del claro del menú la pantalla de la TV empuja el botón de la CBL•SAT en el remoto. La luz de Indicador debe salir indicando que el remoto ahora está fuera de modo del menú de la DBS y que invertirá al modo de operación. Nota: El remoto dará salida automáti­camente al modo del menu de la TV después de 10 segundos de inactividad sin los botones que son empujados.
Notas Especiales:
1. Debido a la variedad amplia de forma
tos del menú, algunos que experimentan pueden ser requeridos.
2. SONY : Presionar el botón mientras
que en menú el modo vuelve al menú anterior.
Característica Del Sueño
Esta característica dará vuelta apagado a su TV cuando usted elige a partir 1 a 99 minutos.
Para programar La Característica Del Sueño:
1. Presione y sostenga el
botón del SLEEP. La luz de Indicador permanecerá se
encendió. Suelta el botón del sueno.
2. Incorpore el tiempo en
minutos usando la
29
-
pista dominante numérica. (minutos 1 a 9: presione 0 antes del número real) (máximo: 99 minutos)
3. Dejan la televisión
dirigida alejada. (La característica del sueño no traba
jará a menos que el remoto se deje la
television dirigida.)
Para dar vuelta Apagado Al Temporizador Del Sueño:
El programa del temporizador del sueño será­cancel do y restauración a cero por cualquiera del siguiente: Presione y sostenga el botón del sueno hasta que la luz de Indicador centelleo o presiona el botón de ON•OFF, dando vuelta a la TV APAGADO.
Localización de Averías
Problema
Luz de indicador que no centelleo cuando usted presiona cualquier clave
El remoto no funciona su dispositivo
No realizándose
Solución
A) Substituya las
baterías (con los acumuladores alcalinos frescos, nuevos del AAA).
B) Controle que las
baterías están instaladas
correctamente.
A) Intente todos los
códigos enumera dos para su marca.
B) Intente el método
de la búsqueda del código (paginación
24).
Comience la búsqueda del código encima otra vez para localizar el código apropiado.
Intente el código del VCR para su marca. Algunas unidades combo, sin embargo, pueden requerir una TV y un código del VCR para la operación completa.
-
-
30
ordena correctamente
Problemas que programan una unidad combo de TV/VCR
VCR que no registra
El canal hacia arriba y hacia abajo no funciona en un RCA TV
Problemas que cambian los canales
Ninguna respuesta después de presionar un clave
La característica del sueño no trabaja
Como característica de seguridad en su remoto, usted debe presionar el botón de REC dos veces.
Debido a alguno diseña, el remoto original real izará solamente estas funciones.
Si su remoto origi nal requerido ENTER después de un canal, la prensa ENTER después de que usted seleccione un canal.
A) Se cercioran de
usted tener baterías nuevas, y usted están apuntando su remoto a sus dis positivos.
B) Controle que las
baterías están instaladas cor rectamente. Vea la paginación 3.
El remoto debe seguir siendo televisión dirigi da después de que el sueño se fije en la orden para que trabaje.
-
-
-
-
-
La reprogramación puede ser requerida
después de que se quiten las baterías.
Garantia Limitada de Noventa
Jasco Products Company garantiza este producto por un periodo de noventa días desde la fecha de la compra original, como libre de defectos de fabricación. Esta garantía está limitada a la reparación o reemplazo de este producto y no se extiende a daños consecuentes o incidentales en otros productos que puedan ser usados con esta unidad. Esta garantía es en vez de cualquier otra expresa o implícita. Algunos estados no permite limitacíones al tiempo de limitada o permite el exclusión o limitaciones del daños incidental o consiguiente, así el
31
Distributed for THOMSON INC.
by Jasco Products Company,
311 N.W. 122nd Street,
Oklahoma City, OK 73114.
www.jascoproducts.com
Loading...