2.4 GHz Wireless
5-Button Optical Mouse
Instruction Manual
98543
For technical support contact Jasco Products at
1-800-654-8483 or www.jascoproducts.com.
TABLE OF CONTENTS
PACKAGE CONTENTS .........................................................................................3
SYSTEM REQUIREMENTS ..................................................................................3
BATTERY INSTALLATION ...................................................................................3
MOUSE INSTALLATION ......................................................................................4
TROUBLE SHOOTING .........................................................................................4
TWO YEAR LIMITED WARRANTY ...................................................................5
FCC STATEMENT ...................................................................................................5
Package Contents
• 2.4 GHz Wireless 5-Button Optical Mouse
• 2 AA Batteries
• Instruction Manual
• USB Nano Receiver
System Requirements
• Windows® 2000 or higher
• Available USB Port
Battery Installation
1) Using your thumb, gently pry open the battery
compartment door on the bottom of the mouse.
2) Remove the old batteries.
3) Insert 2 AA batteries, being sure to match the polarity
of the battery with the polarity marking inside the battery
compartment.
4) Re-attach the battery door.
Mouse Installation
Please keep these directions in a safe place.
1) Slide the USB receiver out of the bottom of the mouse.
2) Insert the USB receiver into an available USB port
3) Squeeze the “Connect” button on the receiver and hold for
three seconds; a red light will begin flashing.
4) Push the “Connect” button on the bottom of the mouse.
This will ensure the mouse and receiver are properly
paired together.
Storing the receiver
To help conserve batteries and enhance portability, the USB nano
receiver is designed to store inside the mouse. To do this, simply
unplug the receiver from your USB port and slide it into the
compartment underneath the mouse. Once the receiver is in
place, the power will automatically shut off.
Trouble Shooting
• Mouse does not work properly
-Check that your batteries are in the mouse properly.
• Reconnect your mouse to the receiver.
-Press the link button on the receiver. Press the link button on
the bottom of your mouse.
• Mouse does not move on screen
-Reconnect your mouse to the receiver.
-Change the batteries in your mouse.
-Make sure that your USB receiver is fully plugged into your
USB port.
Two Year Limited Warranty
Jasco Products Company warrants this product to be free from
manufacturing defects for a period of two years from the original
date of consumer purchase. This warranty is limited to the repair
or replacement of this product only and does not extend to
consequential or incidental damage to other products that may
be used with this unit. This warranty is in lieu of all other warranties express or implied. Some states do not allow limitations on
how long an implied warranty lasts or permit the exclusion or
limitation of incidental or consequential damages, so the above
limitations may not apply to you. This warranty gives you specific
rights, and you may also have other rights which vary from state
to state. If unit should prove defective within the warranty period,
return prepaid with dated proof of purchase to:
Jasco Products Company
10 East Memorial Rd
Oklahoma City, OK 73114
FCC Statement
Notice: Federal Communications Commission (FCC) requirements, Part 15.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
CAUTION: Any changes of modifications not expressly approved
by the grantee of this device could void the users authority to
operate the equipment. This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
Distributed by Jasco Products Company
10 E Memorial Rd
Oklahoma City, OK 73114
www.jascoproducts.com
Loading...