Jasco 19242 User Manual

Page 1
Model 19242
www.jascoproducts.com
Wireless Door Chime Kit
Installation Instructions for Battery Operated Wireless Door Chime Kit
1. Remove the battery cover on the chime.
2. Remove the white Styrofoam block
3. Unplug the red and black wires inside the battery compartment.
4. Remove the battery pack and discard appropriately.
Chime components
Required Tools: Small flat blade screwdriver, drill, 1/16” and 5/32” drill bits, and phillips screwdriver.
Included Hardware:
(2) Plastic screw anchors (2) 4x20mm screws (2) 3x20mm screws (2) Double sided adhesive pads
The wireless door chime Kit has two components:
Styrofoam Block
House Code Door
Try-Me Wires
Page 2
Chime (receiver) Push-Button (Transmitter).
Chime Tune Setting
The chime tune is set by adjusting the dip switches located in the push button. The default setting is “Ding Dong”
The following instructions explain how to change the tune on any wireless push button.
1. Remove the battery from the push button transmitter.
2. Locate the 3 dip switches shown below.
3. Select the desired chime sound from the table below.
ON: Switch On OFF: Switch Off
Page 3
-
Pushbutton Dip Switches and Jumpers
Setting The House Security Code
Each chime component has 4 jumpers for setting the house security code. In most cases you will not need to change the factory settings for the house security code. If your chime activates intermittently or does not work at all, you may be able to solve the problem by changing your security code.
1. Remove power or batteries from the chime.
2. To remove the batteries from the pushbutton, open the pushbutton case as shown below.
3. Locate the House Security Code door and screw located on the
Chime Dip Switches (Ding Dong Shown)
House Code Jumpers
Page 4
back of the chime (See the chime components picture above). Remove the screw and take off the door.
4. Locate the chime and pushbutton jumpers shown below.
Chime and Pushbutton Jumpers
5. To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then test the system for proper operation. The jumpers on the chime and pushbutton must match exactly.
House Code Jumpers
Page 5
Push Button Mounting Instructions
Note: Avoid mounting on metal surfaces, as it may result in a reduced
range of transmission. Do not mount in an area where exposed to direct rain.
a. Removing the back cover
b. Replacing the back cover
1. Push buttons are typically mounted at the same height as the door knob or handle (between 36" and 44" above the floor).
2. Before mounting, choose a mounting location that is not farther than 150 feet from the chime unit location.
Page 6
Not farther than 150 feet
Place push button where you would like to mount and test operation with the chime as close to it’s final location as possible. If it works, mount button here. If it does not work, see TROUBLESHOOTING.
3. Use back cover of push button as a template to mark two screw holes.
4. Drill two holes with 1/16” drill in marked locations.
5. Secure back cover to the mounting surface with the 3x20mm screws.
6. Press front housing onto back cover.
7. Test Operations, if chime does not work, see TROUBLESHOOTING.
Page 7
Chime Unit Mounting Instructions
Note: Avoid mounting on metal surfaces, as it may result in a reduced
range of transmission.
1. Select chime mounting location.
2. Use the supplied chime template to mark mounting holes.
3. Drill 5/32” holes at marked locations.
4. Insert supplied wall anchors into the holes.
5. Insert the 4/20mm screws into the anchors, setting the screw heads extending about 1/4" from mounting surface.
6. Place the chime unit’s keyhole slots over the screws and press down on the chime unit to secure it.
Operation
Page 8
1. Slide power switch to “On” to turn on the chime.
2. Gently press transmitter button to sound chime.
Troubleshooting
Chime doesn't work:
1. Make sure push button switch is depressed and held for at least 1 second.
2. Make sure house code switches 1-4 on chime and push button match exactly.
3. Verify battery orientation in push button.
4. Try fresh batteries.
5. Make sure chime is not farther than 150 feet away from push button.
6. Ensure push button is not mounted on metal, near metal studs, or near the Floor.
7. Try a new location for the chime.
Functional range may be adversely affected by one or more of the following factors: weather, radio frequency interference, low transmitter battery and obstructions between the transmitter and receiver. This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept interference received, including any interference that
may cause undesired operation.
For technical support contact Jasco Products Company at 1-800-654-8483
Page 9
or www.jascoproducts.com
Made in China Hecho en China
Distributed by: Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. www.jascoproducts.com
19242
Loading...