'()*+,-./01+,+
Operation Manual
Jandy® WaterColors LED,
Underwater Large and Small Light
FOR YOUR SAFETY - This product must be installed and serviced by a pro fes sion al pool/spa
builder or service technician. The procedures in this manual must be followed ex act ly. Failure to follow warning notices and instructions may result in property damage, serious injury,
or death. Improper in stal la tion and/or operation will void the war ran ty. Before installing this
product, read and follow all warning notices and instructions that accompany this lter.
!"#"$%""&
WARNING
Table of Contents
2+3)0#
Section 1. Safety Information ...................... 4
Section 2. Jandy WaterColors LED Light
Operating Instructions ............... 5
4560 7.0'()*+,)0,8)09-38,0+/:0;8+/3)0;.<.*=05555$
4540 7.0>)=),0,.0,8)0?)3-//-/30.@0,8)0;.<.*0
A)BC)/D)55555555555555555555555555555555555555555555555555555$
Figures and Tables
L-3C*)0650 >)K.M-/30,8)0F+/:G0H+,)*;.<.*=09-38,0
&==)KN<G0@.*09-38,0I/3-/)0>)(<+D)K)/,0555%
L-3C*)0450 AK+<<09-38,0I/3-/)0O2;?P0>)(<+D)K)/,0
+/:0H-*-/3055555555555555555555555555555555555555555555555555Q
L-3C*)0#50 9+*3)09-38,0I/3-/)0O2;?P0>)(<+D)K)/,0
+/:0H-*-/3055555555555555555555555555555555555555555555555555Q
L-3C*)0E50 ;*.==0A)D,-./0.@0F+/:G0H+,)*;.<.*=09I10
9-38,055555555555555555555555555555555555555555555555555555555555 R
L-3C*)0$50 &<-3/K)/,0.@0,8)09)/=S0L+D)0>-/3S0!.C=-/30
+/:0;<+K(=0@.*0;.<.*09-38,=05555555555555555555555R
L-3C*)0%50 F+/:G09+*3)0H+,)*;.<.*=09I109-38,0
IT(<.:):0U-)V05555555555555555555555555555555555555555555 J
L-3C*)0Q50 F+/:G0AK+<<0H+,)*;.<.*=09I109-38,0
IT(<.:):0U-)V055555555555555555555555555555555555555555 6"
Section 3. Replacing Light Engine (PCB) ... 5
Section 4. Exploded View and Replacement
Parts.............................................9
E560 F+/:G09+*3)0H+,)*;.<.*=09I109-38,055555555555J
E540 F+/:G0AK+<<0H+,)*;.<.*=09I109-38,05555555556"
7+N<)0650 F+/:G0H+,)*;.<.*=09-38,=0A)BC)/D)0555555555$
7+N<)0450 9-38,0A()D-@-D+,-./=0555555555555555555555555555555555555$
2+3)0E
Section 1. Safety Information
IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
READ AND FOLLOW ALL INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the
following:
WARNING
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION.
<-D)/=):0.*0D)*,-@-):0)<)D,*-D-+/0-/0+DD.*:+/D)0V-,80,8)0W+,-./+<0I<)D,*-D+<0;.:)0+/:0+((<-D+N<)0<.D+<0D.:)=0+/:0
.*:-/+/D)=500XK(*.()*0-/=,+<<+,-./0V-<<0D*)+,)0+/0)<)D,*-D+<08+Y+*:S0V8-D80D.C<:0*)=C<,0-/0:)+,80.*0=)*-.C=0-/ZC*G0,.0
(..<0.*0=(+0C=)*=S0-/=,+<<)*=S0.*0.,8)*=0:C)0,.0)<)D,*-D+<0=8.D[S0+/:0K+G0+<=.0D+C=)0:+K+3)0,.0(*.()*,G500>)+:0
+/:0@.<<.V0,8)0=()D-@-D0-/=,*CD,-./=0N)<.V5
78-=0C/:)*V+,)*0<-38,0KC=,0N)0-/=,+<<):0NG0+0
WARNING
?)@.*)0-/=,+<<-/30,8-=0C/:)*V+,)*0<-38,S0*)+:0+/:0@.<<.V0+<<0V+*/-/30/.,-D)=0+/:0-/=,*CD,-./=0+DD.K(+/G-/30,8-=0
<-38,50L+-<C*)0,.0@.<<.V0=+@),G0V+*/-/3=0+/:0-/=,*CD,-./=0D+/0*)=C<,0-/0=)M)*)0-/ZC*GS0:)+,8S0.*0(*.()*,G0:+K+3)50
;+<<0OQ"QP0QQ%\R4""0@.*0+::-,-./+<0@*))0D.(-)=0.@0,8)=)0-/=,*CD,-./=5
CAUTION
ITD)(,0V8)/0,8)0F+/:G0H+,)*;.<.*=09I109-38,=0+*)0-/=,+<<):0-/0+/0+*)+0.@0,8)0=V-KK-/30(..<0,8+,0-=0/.,0C=):0
@.*0=V-KK-/30+/:0,8)0<)/=0-=0+:)BC+,)<G03C+*:):0,.0[))(0+/G0()*=./0@*.K0D./,+D,-/30-,S0,8)0<-38,0=8+<<0N)0
-/=,+<<):0-/0.*0./0+0V+<<0.@0,8)0(..<S0V-,80,8)0,.(0.@0,8)0<)/=0.()/-/30/.,0<)==0,8+/06R0-/D8)=0OE$Q0KKP0N)<.V0,8)0
/.*K+<0V+,)*0<)M)<0.@0,8)0(..<
ATTENTION INSTALLER: 078-=0K+/C+<0D./,+-/=0-K(.*,+/,0-/@.*K+,-./0+N.C,0,8)0
-/=,+<<+,-./S0.()*+,-./0+/:0=+@)0C=)0.@0,8-=0(*.:CD,5078-=0-/@.*K+,-./0=8.C<:0N)03-M)/0,.0,8)0
.V/)*].()*+,.*0.@0,8-=0)BC-(K)/,5
NOTICE
78)0F+/:G0H+,)*;.<.*=09I109-38,=0+*)0-/,)/:):0@.*0-/=,+<<+,-./0-/0@*)=80V+,)*0+/:0=+<,0V+,)*0=V-KK-/30(..<=50
X,0-=0-K(.*,+/,0,.0)/=C*)0,8+,0,8)0V),0/-D8)=0-/0V8-D80,8)0<-38,=0+*)0-/=,+<<):0+*)0-/,)/:):0@.*0,8)-*0+((*.(*-+,)0
+((<-D+,-./S0)-,8)*0@*)=80V+,)*0.*0=+<,0V+,)*0(..<=5
SAVE THESE INSTRUCTIONS
2+3)0$
Section 2. Jandy WaterColors
LED Light Operating
Instructions
2.1 To Operate the Light and Change
Colors
Turn the light ON. The time the light is turned on,
the color sequence begins with the Alpine White. To
change the color, turn the light OFF and then ON within
three (3) seconds. Continue turning OFF and ON until
the desired light color mode is reached. See Table 1 for
the color mode sequence.
Table 1. Jandy WaterColors Lights Sequence
Sequence Order Color Modes
6 &<(-/)0H8-,)
4 A[G0?<C)
# ;.N+<,0?<C)
E ;+*-NN)+/0?<C)
$ A(*-/30^*))/
% IK)*+<:0^*))/
Q IK)*+<:0>.=)
R _+3)/,+
J U-.<),
6" A<.V0;.<.*0A(<+=8
66 L+=,0;.<.*0A(<+=8
64 &K)*-D+0,8)0?)+C,-@C<
6# L+,07C)=:+G
6E 1-=D.07)D8
NOTE H8)/0,8)0<-38,0-=0,C*/):0'LL0@.*0K.*)0,8+/0
=)M)/0OQP0=)D./:=S0-,0V-<<0*)K+-/0-/0,8)0D.<.*0=),0
,8+,0-=0DC**)/,<G0+D,-M)50H8)/0,8)0<-38,0-=0,C*/):0
N+D[0'WS0,8)0<-38,0V-<<0N)0./0,8)0=+K)0D.<.*0=),5
2.2 To Reset to the Beginning of the
Color Sequence
Turn the light OFF, wait four (4) to six (6) seconds, then
turn ON, the light will return to the beginning of the
color cycle (Alpine White).
NOTE X@0+/0&BC+9-/[0>A0D./,*.<0=G=,)K0-=0N)-/30C=):0
,8)0D.<.*0=),0D+/0N)0=)<)D,):0C=-/30,8)0-/:..*0
D./,*.<<)*5
Section 3. Replacing Light Engine
(PCB)
WARNING
&<V+G=0:-=D.//)D,0(.V)*0,.0,8)0D.<.*0<-38,0+,0,8)0
D-*DC-,0N*)+[)*0N)@.*)0=)*M-D-/30,8)0<-38,50L+-<C*)0,.0:.0
=.0D.C<:0*)=C<,0-/0:)+,80.*0=)*-.C=0-/ZC*G0,.0-/=,+<<)*S0
=)*M-D)K+/S0(..<0.*0=(+0C=)*=0.*0.,8)*=0:C)0,.0
)<)D,*-D+<0=8.D[5
1. Turn off the main electrical switch or circuit
breaker, as well as the switch, which operates the
underwater light.
2. Be sure to have the following items:
$ A new lens gasket, P/N R0451101 for the large
light or P/N R0400501 for the small light.
$ A light engine. See Table 2 for speci cation.
WARNING
>)(<+D)0<-38,0)/3-/)0V-,80,8)0=+K)0,G()50L+-<C*)0
,.0*)(<+D)0,8)0<-38,0)/3-/)0V-,80,8)0=+K)0,G()0V-<<0
:+K+3)0,8)0<-38,0+==)KN<G0+/:0K+G0D+C=)0+/0
)<)D,*-D+<08+Y+*:0*)=C<,-/30-/0:)+,80.*0=)*-.C=0-/ZC*G0
,.0(..<0.*0=(+0C=)*=S0-/=,+<<)*=S0.*0.,8)*=0:C)0,.0
)<)D,*-D+<0=8.D[S0+/:0K+G0+<=.0D+C=)0:+K+3)0,.0
(*.()*,G50?)0=C*)0,8)0(.V)*0-=0=V-,D8):0'LL0N)@.*)0
*)K.M-/30.*0-/=,+<<-/302;?50&<<.V02;?0,.0D..<0N)@.*)0
*)(<+D-/3505
3. To remove the light assembly, unscrew the special
pilot screw at the top of the face ring, remove light
assembly from niche and gently place assembly
on the deck. It is not necessary to drain down the
pool. See Figure 1.
Table 2. Light Speci cations
Model Fixture
Voltage
Jandy WaterColors
Large Light
Jandy WaterColors
Large Light
Jandy WaterColors
Small Light
Jandy WaterColors
Small Light
640U.<,0&; >"EQE"""
64"0U.<,0&; >"EQE6""
640U.<,0&; >"EQ#J""
64"0U.<,0&; >"EQ#J""
Light Engine (PCB)
Part Number
NOTE
7.0=G/D8*./-Y)0D.<.*=0./0KC<,-(<)0F+/:G0
H+,)*;.<.*=09-38,0=G=,)K=0V-*):0,.0=)(+*+,)0
=V-,D8)=S0()*@.*K0,8)0+N.M)0+D,-./=0./0
+<<0.@0,8)-*0=V-,D8)=0=-KC<,+/).C=<G500&<<0
F+/:G0H+,)*;.<.*=09-38,=0V-<<0=G/D8*./-Y)0
+C,.K+,-D+<<G0-@0+D,-M+,):0NG0,8)0=+K)0=V-,D8500
W.0.,8)*0+DD)==.*-)=0+*)0*)BC-*):5
2+3)0%
washer and secure both with the nut. Torque
to 12 in-lbs.
7. Plug in the quick disconnect wire (white
for the 12V and red for the 120V) onto the
terminal (AC1) of the light engine.
8. Plug in the quick disconnect wire (black for
the 12V and blue for the 120V) onto terminal
(AC2) of the light engine.
b. Large Light Engine (PCB) Replacement (120V
and 12V)
1. Remove three (3) nuts and washers.
2. Unplug the quick disconnect terminals from
the PCB.
3. Remove the light engine from the light fixture.
4. Place new light engine into the fixture with the
orientation shown in Figure 3.
5 Secure the new light engine (PCB) with two
(2) nylon washers and two (2) nuts. Torque to
12 in-lbs.
6. Plug in the white quick disconnect wire onto
the terminal (J2) of the light engine.
7. Plug in the black quick disconnect wire onto
terminal (J6) of the light engine for the 12V
models; or terminal (J3) of the light engine for
120V models.
8a. For 12V models, place a nylon washer on the
stud and place the green ground wire terminal
on the nylon washer and secure both with the
nut. Torque to 12 in-lbs.
8b. For 120V models, place the green ground wire
on the stud and secure with the nut. Torque to
12 in-lbs.
a. Loosen the Phillips head screws (six (6) for small
light, eight (8) for large light) to allow the bottom
clamp to be removed from the face ring assembly.
Do not remove the screws or the retaining rings.
The retaining rings prevent the screws from falling
free from the bottom clamp and also aid in ease of
assembly.
b. Remove the bottom clamp, the face ring assembly,
the glass lens, and the gasket from the fixture.
Remove the gasket from the lens. Refer to
Section
4, Exploded View and Replacement Parts
a. 12V Small Light Engine (PCB) Replacement
1. Remove two (2) nuts and two (2) washers.
2. Unplug the quick disconnect terminals from the
light engine.
3. Remove the light engine from the light fixture.
4. Place new light engine into the fixture with
the
orientation shown in Figure 2.
5 Secure the light engine with one (1) nylon washer
and one (1) nut. Torque to 12 in-lbs.
6. Place a nylon washer on the other stud and place
the green ground wire terminal on the nylon
WARNING
?)0=C*)0,.0[))(0,8)0=()D-+<0(-<.,0=D*)V0@*.K0,8-=0
C/:)*V+,)*0<-38,5078-=0=D*)V0K.C/,=0+/:0)<)D,*-D+<<G0
3*.C/:=0,8)08.C=-/30=)DC*)<G0,.0,8)0K.C/,-/30*-/30
+/:0V),0/-D8)50L+-<C*)0,.0C=)0,8)0=D*)V0(*.M-:):0
D.C<:0D*)+,)0+/0)<)D,*-D+<08+Y+*:S0V8-D80D.C<:0*)=C<,0
-/0:)+,80.*0=)*-.C=0-/ZC*G0,.0(..<0.*0=(+0C=)*=S0
-/=,+<<)*=0.*0.,8)*=0:C)0,.0)<)D,*-D+<0=8.D[5
4. Pool Clamp Removal.
a. Loosen the Phillips head screws (six (6) for small
light, eight (8) for large light) to allow the bottom
clamp to be removed from the face ring assembly.
Do not remove the screws or the retaining rings.
The retaining rings prevent the screws from falling
free from the bottom clamp and also aid in ease of
assembly.
b. Remove the bottom clamp, the face ring assembly,
the glass lens, and the gasket from the fixture.
Remove the gasket from the lens. Refer to
4, Exploded View and Replacement Parts..
Section
5. Light Engine Replacement
a. 12V Small Light Engine (PCB) Replacement
1. Remove two (2) nuts and two (2) washers.
2. Unplug the quick disconnect terminals from the
light engine.
3. Remove the light engine from the light fixture.
washer and secure both with the nut. Torque
to 12 in-lbs.
7. Plug in the quick disconnect wire (white
for the 12V and red for the 120V) onto the
terminal (AC1) of the light engine.
8. Plug in the quick disconnect wire (black for
the 12V and blue for the 120V) onto terminal
(AC2) of the light engine.
b. Large Light Engine (PCB) Replacement (120V
and 12V)
1. Remove three (3) nuts and washers.
2. Unplug the quick disconnect terminals from
the PCB.
3. Remove the light engine from the light fixture.
4. Place new light engine into the fixture with the
orientation shown in Figure 3.
5 Secure the new light engine (PCB) with two
(2) nylon washers and two (2) nuts. Torque to
12 in-lbs.
6. Plug in the white quick disconnect wire onto
the terminal (J2) of the light engine.
7. Plug in the black quick disconnect wire onto
terminal (J6) of the light engine for the 12V
models; or terminal (J3) of the light engine for
120V models.
4. Place new light engine into the fixture with
orientation shown in Figure 2.
5 Secure the light engine with one (1) nylon washer
and one (1) nut. Torque to 12 in-lbs.
6. Place a nylon washer on the other stud and place
the green ground wire terminal on the nylon
Power
Bonding
cable
Cord
Niche
the
POOL LIGHT
ASSEMBLY
8a. For 12V models, place a nylon washer on the
stud and place the green ground wire terminal
on the nylon washer and secure both with the
nut. Torque to 12 in-lbs.
8b. For 120V models, place the green ground wire
on the stud and secure with the nut. Torque to
12 in-lbs.
POOL WALL
Unscrew pilot screw
and pull top of light
1
assembly away from
pool wall
PILOT SCREW
2
Push up on
bottom of
light assembly
Power
Cord
Bonding
cable
SPA LIGHT
ASSEMBLY
Niche
Figure 1. Removing the Jandy WaterColors Light Assembly for Light Engine Replacement
2+3)0Q
a. If not already done, remove the gasket from the
glass lens and install a new gasket, P/N R0451101
for the large light and R0400501 for the small
light, on the lens. On the small light, remove the
diverger from the lens.
b. While holding the fixture upright, place the glass
lens with the gasket on top of the fixture. Please
note that the lens gasket is not symmetrical.
Therefore, it must be installed correctly so that
the lens can seal to the fixture housing. Place the
gasket on the lens so that the thick molded side
of the gasket will mate with the housing when the
lens is installed.
See Figure 4. On the small light,
replace the diverger by tucking the tabs between
the lens and gasket.
c. Position the lens and gasket on the fixture. Place
the face ring assembly over the lens and align the
pilot screw with the small arrow mark on the face
of the lens. Note that the small arrow mark on the
face of the lens and the pilot screw of the face ring
must be aligned with the arrow located on fixture
label that reads, ]Arrow on this label must line up
with the pilot screw on the Face Ring^. See
Figure 5.
6. Reassemble the xture.
a. If not already done, remove the gasket from the
glass lens and install a new gasket, P/N R0451101
for the large light and R0400501 for the small
light, on the lens. On the small light, remove the
diverger from the lens.
NOTE0 &0/)V0<)/=03+=[),0KC=,0N)0C=):0)+D80,-K)0,8)0
<-38,0-=0*)+==)KN<):500
H8-,)0O64UP
>):0O64"UP
WG<./
H+=8)*
AC1 AC2
WC,
Figure 2. Small Light Engine (PCB) Replacement
and Wiring
^*))/0
?<+D[0O64UP
?<C)0O64"UP
9-38,0
I/3-/)
A)DC*)0
L-*=,
WARNING
Risk of Electrical Shock or Electrocution.0&<V+G=0
-/=,+<<0+0/)V0<)/=03+=[),0V8)/)M)*0:-=+==)KN<-/30
,8)0<-38,0OF+/:G0;.<.*09-38,0^+=[),02]W0>"E$66"60@.*0
<+*3)0<-38,0+/:02]W0>"E""$"60@.*0=K+<<0<-38,P50L+-<C*)0
,.0:.0=.0K+G0()*K-,0V+,)*0,.0<)+[0-/,.0,8)0+==)KN<GS0
V8-D80D.C<:0D+C=)`
O+P00&/0)<)D,*-D+<08+Y+*:0*)=C<,-/30-/0:)+,80.*0=)*-.C=0
-/ZC*G0,.0(..<0.*0=(+0C=)*=S0-/=,+<<)*=S0.*0.,8)*=0:C)0,.0
)<)D,*-D+<0=8.D[S0.*0
ONP00&0K+<@C/D,-./0.@0,8)0F+/:G0H+,)*;.<.*=09-38,S0
V8-D80<-[)V-=)0D.C<:0*)=C<,0-/0=)*-.C=0-/ZC*G0,.0(..<0.*0
=(+0C=)*=S0-/=,+<<)*=S0.*0NG=,+/:)*=S0.*0-/0:+K+3)0,.0
(*.()*,G5
b. While holding the fixture upright, place the glass
lens with the gasket on top of the fixture. Please
note that the lens gasket is not symmetrical.
Therefore, it must be installed correctly so that
the lens can seal to the fixture housing. Place the
gasket on the lens so that the thick molded side
of the gasket will mate with the housing when the
lens is installed.
replace the diverger by tucking the tabs between
the lens and gasket.
NOTE0 ?)0=C*)0,.0@+D)0,8)0:C<<0=-:)0.@0,8)0:-M)*3)*0
:.V/0,.V+*:=0,8)02;?5
c. Position the lens and gasket on the fixture. Place
the face ring assembly over the lens and align the
pilot screw with the small arrow mark on the face
of the lens. Note that the small arrow mark on the
face of the lens and the pilot screw of the face ring
must be aligned with the arrow located on fixture
label that reads, ]Arrow on this label must line up
with the pilot screw on the Face Ring^. See
Figure 5.
See Figure 4. On the small light,
?<+D[
WG<./
H+=8)*
WC,
F%
F4
Figure 3. Large Light Engine (PCB) Replacement and Wiring
^*))/
H8-,)
A)DC*)0
L-*=,
WC,
^*))/
H8-,)
?<+D[
F#
F4
A)DC*)0
L-*=,
64"U0H-*-/364U0H-*-/3
2+3)0R
d. While holding the aligned face ring assembly and
fixture together, turn the assembly upside down
and set it on the old gasket, using the old gasket
as an assembly fixture. This will keep the lens and
gasket assembly from being pushed out of the face
ring while you secure it to the light fixture.
e. Spread the bottom clamp over the electrical cord
and slide it onto the back of fixture to the top
clamp.
f. Tighten the Phillips head screws (eight (8) for
large light and six (6) for small light) on the color
light in alternating cross-pattern. Torque screws to
approximately 20 in-lbs. Do not over-tighten.
g. Discard the old gasket.
a. Coil the extra four (4) feet of cord around the
fixture or into the base of the niche and place the
light assembly into the niche.
b. Engage the retainer tab on the bottom of the face
ring, then pivot the top of the fixture inward and
tighten the special pilot screw.
d. While holding the aligned face ring assembly and
fixture together, turn the assembly upside down
and set it on the old gasket, using the old gasket
as an assembly fixture. This will keep the lens and
gasket assembly from being pushed out of the face
ring while you secure it to the light fixture.
e. Spread the bottom clamp over the electrical cord
and slide it onto the back of fixture to the top
clamp.
f. Tighten the Phillips head screws (eight (8) for
large light and six (6) for small light) on the color
light in alternating cross-pattern. Torque screws to
approximately 20 in-lbs. Do not over-tighten.
g. Discard the old gasket.
WARNING
a=)0./<G0,8)0=()D-+<0(-<.,0=D*)V0(*.M-:):0V-,80,8-=0
C/:)*V+,)*0<-38,5078-=0=D*)V0K.C/,=0+/:0)<)D,*-D+<<G0
3*.C/:=0,8)08.C=-/30=)DC*)<G0,.0,8)0K.C/,-/30*-/30
+/:0V),0/-D8)50L+-<C*)0,.0C=)0,8)0=D*)V0(*.M-:):0
D.C<:0D*)+,)0+/0)<)D,*-D+<08+Y+*:S0V8-D80D.C<:0*)=C<,0
-/0:)+,80.*0=)*-.C=0-/ZC*G0,.0(..<0.*0=(+0C=)*=S0
-/=,+<<)*=0.*0.,8)*=0:C)0,.0)<)D,*-D+<0=8.D[5
8. If pool is empty, ll the pool until the underwater
light is completely submerged in water before
operating the light for more than 10 seconds. Turn
on main switch or circuit breaker, as well as the
switch, which speci cally operates the underwater
light, to check for proper operation.
7. Reinstall the Jandy Light into niche xture.
a. Coil the extra four (4) feet of cord around the
fixture or into the base of the niche and place the
light assembly into the niche.
b. Engage the retainer tab on the bottom of the face
ring, then pivot the top of the fixture inward and
tighten the special pilot screw.
78-D[0K.<:):0
=-:)0.@0,8)0
3+=[),0KC=,0
K+,)0V-,80
,8)0N.:G0.@0
,8)08.C=-/3
WARNING
W)M)*0.()*+,)0,8-=0C/:)*V+,)*0<-38,0@.*0K.*)0,8+/0
6"0=)D./:=0C/<)==0-,0-=0,.,+<<G0=CNK)*3):0-/0V+,)*50
H-,8.C,0,.,+<0=CNK)*=-./S0,8)0<-38,0+==)KN<G0V-<<03),0
)T,*)K)<G08.,S0V8-D80K+G0*)=C<,0-/0=)*-.C=0NC*/=0.*0-/0
:+K+3)0,.0,8)0<-38,5078-=0K+G0*)=C<,0-/0=)*-.C=0-/ZC*G0
,.0(..<0.*0=(+0C=)*=S0-/=,+<<)*=S0.*0NG=,+/:)*=0.*0-/0
:+K+3)0,.0(*.()*,G5
Figure 4. Cross Section of Jandy WaterColors LED
Light
&<-3/0+**.V0.@0,8)0
<)/=0V-,80,8)0(-<.,0
=D*)V
Figure 5. Alignment of the Lens, Face Ring, Housing and Clamps for Color Lights
&<-3/0(-<.,0=D*)V0V-,80
,8)0+**.V0<.D+,):0./0
,8)00T,C*)0<+N)<
Section 4. Exploded View and Replacement Parts
4.1 Jandy Large WaterColors LED Light
$
R
64
#$E%Q
2+3)0J
Q
Figure 6. Jandy Large WaterColors LED Light Exploded View
DWG # Part # Description Field Replaceable
6 W]& H+,)*;.<.*=09-38,0!.C=-/3 NO - Purchase New Light
4 >"EQE""" 9-38,0I/3-/)02;?S064U09+*3)09I109-38,0V]09-38,0A8+(-/301-M)*3)* YES
4 >"EQE6"" 9-38,0I/3-/)02;?S064"U09+*3)09I109-38,0V]09-38,0A8+(-/301-M)*3)* YES
# >"E$66"6 A-<-D./)0^+=[), YES
E >"E$"%"6 ^<+==09)/= YES
$ >"E$"Q"6 ;<+K(0&==)KN<G YES
% >"E$"R"6 L+D)0>-/3S0A,+-/<)==0A,))<0OAAP YES
% >"E$"R"4 L+D)0>-/3S02<+=,-DS0H8-,) YES
% >"E$"R"# L+D)0>-/3S02<+=,-DS0?<+D[ YES
% >"E$"R"E L+D)0>-/3S02<+=,-DS0^*+G YES
% >"E$"R"$ L+D)0>-/3S02<+=,-D0A), YES
Q >"E$"J"6 2-<.,0AD*)VS0V-,80>),+-/)* YES
R >"E$6""6 ;<+K(0AD*)V=0OR0AD*)V=0+/:0R0>),+-/)*=P YES
2+3)06"
4.2 Jandy Small WaterColors LED Light
Q
J
64
E
#
R
$
%
Q
R
Figure 7. Jandy Small WaterColors LED Light Exploded View
DWG # Part # Description Field Replaceable
6 W]& H+,)*;.<.*=09-38,0!.C=-/3 NO - Purchase New Light
4 >"EQ#J"" 9-38,0I/3-/)S064U]64"U0AK+<<09I109-38, YES
# >"EQE4"" 1-M)*3)*S09-38,0A8+(-/3S0AK+<<09I109-38, YES
E >"E""$"6 A-<-D./)0^+=[), YES
$ >"E""%"6 ^<+==09)/= YES
% >"E$64"6 ;<+K(0&==)KN<G YES
Q >"E$6#"6 L+D)0>-/3S0A,+-/<)==0A,))<0OAAP YES
Q >"E$6#"4 L+D)0>-/3S02<+=,-DS0H8-,) YES
Q >"E$6#"# L+D)0>-/3S02<+=,-DS0?<+D[ YES
Q >"E$6#"E L+D)0>-/3S02<+=,-DS0^*+G YES
Q >"E$6#"$ L+D)0>-/3S02<+=,-D0A), YES
R >"E$"J"6 2-<.,0AD*)VS0V-,80>),+-/)* YES
J >"E$6E"6 ;<+K(0AD*)V=0O%0AD*)V=0+/:0%0>),+-/)*=P YES
W.,)=
2+3)066
LIMITED WARRANTY
78+/[0G.C0@.*0(C*D8+=-/30F+/:G000(..<0+/:0=(+0(*.:CD,=50F+/:G02..<02*.:CD,=S0X/D50V+**+/,=0+<<0(+*,=0,.0N)0@*))
000 000 0 0 0 00 00 00
@*.K0K+/C@+D,C*-/30:)@)D,=0-/0K+,)*-+<=0+/:0V.*[K+/=8-(0@.*0+0()*-.:0.@0./)0O6P0G)+*0@*.K0,8)0:+,)0.@0*),+-<
00000000000000000
(C*D8+=)S0V-,80,8)0@.<<.V-/30)TD)(,-./=`
c
0&BC+9-/[
b
0W)M)*09CN)
b
0&BC+2C*) I<)D,*./-D0;8<.*-/)0^)/)*+,.*0I<)D,*.<G,-D0;)<<=0D+**G0+0@-M)0O$P0G)+*0<-K-,):0V+**+/,G0./0+0(*.*+,):0N+=-=5
b
0>A0C/-,=0-/=,+<<):0V-,80F+/:G0AC*3)02*.,)D,-./0d-,=0V-<<0N)0D.M)*):0@.*0,V.0O4P0G)+*=5
c
0M+<M)=0+*)0V+**+/,):0@.*0,8)0<-@)0.@0(..<0+/:].*0=(+0./0V8-D80,8)G0V)*)0.*-3-/+<<G0-/=,+<<):5
c
78-=0V+**+/,G0-=0<-K-,):0,.0,8)0 @-*=,0*),+-<0 (C*D8+=)*S0-=0/.,0,*+/=@)*+N<)S0+/:0:.)=0/.,0+((<G0,.0(*.:CD,=0,8+,08+M)0
N))/0K.M):0@*.K0,8)-*0.*-3-/+<0 -/=,+<<+,-./0 =-,)=5078)0<-+N-<-,G0.@0F+/:G02..<02*.:CD,=S0X/D50=8+<<0/.,0)TD)):0 ,8)0
*)(+-*0 .*0 *)(<+D)K)/,0 .@0 :)@)D,-M)0 (+*,=0 +/:0 :.)=0 /.,0 -/D<C:)0 +/G0D.=,=0 @.*0 <+N.*0 ,.0*)K.M)0 +/:0 *)-/=,+<<0 ,8)0
:)@)D,-M)0 (+*,S0 ,*+/=(.*,+,-./0 ,.0 .*0 @*.K0 ,8)0 @+D,.*GS0 +/:0 +/G0 .,8)*0 K+,)*-+<=0 *)BC-*):0 ,.0 K+[)0 ,8)0 *)(+-*5078-=0
V+**+/,G0:.)=0/.,0D.M)*0@+-<C*)=0.*0K+<@C/D,-./=0*)=C<,-/30@*.K0,8)0@.<<.V-/3`
650L+-<C*)0,.0(*.()*<G0-/=,+<<S0.()*+,)0.*0K+-/,+-/0,8)0(*.:CD,O=P0-/0+DD.*:+/D)0V-,80.C*0(CN<-=8):0X/=,+<<+,-./S
'()*+,-./0+/:0_+-/,)/+/D)0_+/C+<=0(*.M-:):0V-,80,8)0(*.:CD,O=P5
45078)0V.*[K+/=8-(0.@0+/G0-/=,+<<)*0.@0,8)0(*.:CD,O=P5
#50W.,0K+-/,+-/-/30+0(*.()*0D8)K-D+<0N+<+/D)0-/0G.C*0(..<0+/:].*0=(+0e(!0<)M)<0N),V))/0Q540+/:0Q5RS07.,+<
&<[+<-/-,G0O7&P0N),V))/0R"0,.064"0((KS07.,+<01-==.<M):0A.<-:=0O71AP0<)==0,8+/04"""0/.,0-/D<C:-/30=+<,0((Kf5
E50&NC=)S0+<,)*+,-./S0+DD-:)/,S0@-*)S0@<..:S0<-38,/-/3S0*.:)/,=S0-/=)D,=S0/)3<-3)/D)0.*0+D,=0.@0^.:5
$50AD+<-/3S0@*))Y-/3S0.*0.,8)*0D./:-,-./=0D+C=-/30-/+:)BC+,)0V+,)*0D-*DC<+,-./5
%50'()*+,-/30,8)0(*.:CD,O=P0+,0V+,)*0@<.V0*+,)=0.C,=-:)0,8)0(CN<-=8):0K-/-KCK0+/:0K+T-KCK0=()D-@-D+,-./=5
Q50a=)0.@0/./\@+D,.*G0+C,8.*-Y):0(+*,=0.*0+DD)==.*-)=0-/0D./ZC/D,-./0V-,80,8)0(*.:CD,O=P5
R50;8)K-D+<0D./,+K-/+,-./0.@0D.KNC=,-./0+-*0.*0-K(*.()*0C=)0.@0=+/-,-Y-/30D8)K-D+<=S0=CD80+=0-/,*.:CD-/3
=+/-,-Y-/30D8)K-D+<=0C(=,*)+K0.@0,8)08)+,)*0+/:0D<)+/)*08.=)0.*0,8*.C380,8)0=[-KK)*5
J50'M)*8)+,-/3g0-/D.**)D,0V-*)0*C/=g0-K(*.()*0)<)D,*-D+<0=C((<Gg0D.<<+,)*+<0:+K+3)0D+C=):0NG0@+-<C*)0.@0'\>-/3=S
1I03*-:=S0.*0D+*,*-:3)0)<)K)/,=g0.*0:+K+3)0D+C=):0NG0*C//-/30,8)0(CK(0V-,80-/=C@@-D-)/,0BC+/,-,-)=0.@0V+,)*5
c
LIMITATION OF LIABILITY:
78-=0-=0 ,8)0./<G0V+**+/,G03-M)/0NG0F+/:G02..<02*.:CD,=S0X/D50W.0./)0 -=0+C,8.*-Y):0,.0K+[)0+/G0.,8)*0V+**+/,-)=0
./0 N)8+<@0 .@0 F+/:G0 2..<0 2*.:CD,= S0 X/D50 THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF FITNESS
FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. JANDY POOL PRODUCTS, INC. EXPRESSLY
DISCLAIMS AND EXCLUDE S ANY LIABILIT Y FOR CONSEQUENTIAL , INCIDEN TAL, INDIREC T OR
PUNITIVE DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY.078-=0V+**+/,G03-M)=0
G.C0=()D-@-D0<)3+<0*-38,=50h.C0K+G0+<=.08+M)0.,8)*0*-38,=0,8+,0M+*G0NG0=,+,)0.*0(*.M-/D)5
WARRANTY CLAIMS:
L.*0(*.K(,0V+**+/,G0D./=-:)*+,-./S0D./,+D,0G.C*0:)+<)*0+/:0(*.M-:)0,8)0@.<<.V-/30-/@.*K+,-./`0(*..@0.@0(C*D8+=)S0
K.:)<0 /CKN)*S0 =)*-+<0 /CKN)*0 +/:0 :+,)0 .@0 -/=,+<<+,-./50 78)0 -/=,+<<)*0 V-<<0 D./,+D,0 ,8)0 @+D,.*G0 @.*0 -/=,*CD,-./=0
*)3+*:-/30,8)0D<+-K0+/:0,.0:),)*K-/)0,8)0<.D+,-./0.@0,8)0/)+*)=,0:)=-3/+,):0=)*M-D)0D)/,)*50X@0 ,8)0 :)+<)*0 -=0 /.,0
+M+-<+N<)S0 G.C0 D+/0 <.D+,)0 +0 =)*M-D)0 D)/,)*0 -/0 G.C*0 +*)+0 NG0 M-=-,-/30 VVV5Z+/:G5D.K0 .*0 NG0 D+<<-/30.C*0 ,)D8/-D+<0
=C((.*,0 :)(+*,K)/,0 +,0 OQ"QP0 QQ%\R4""0 )T,)/=-./0 4%"50 &<<0 *),C*/):0 (+*,=0 KC=,0 8+M)0 +0 >),C*/):0 _+,)*-+<0
&C,8.*-Y+,-./0/CKN)*0,.0N)0)M+<C+,):0C/:)*0,8)0,)*K=0.@0,8-=0V+**+/,G5
F+/:G02..<02*.:CD,=S0X/D5
!"#"$%""&
%"""0;./:.*01*-M)S0_..*(+*[S0;&S0aA&0J#"4600b00Q"Q5QQ%5R4""00L&i0Q"Q5Q%#5QQR$
L.*0,)D8/-D+<0=C((.*,0D+<<0Q"Q\QQ%\R4""S0)T,504%"
9-,8.0-/0a5A5&50j04""R0F+/:G02..<02*.:CD,=S0X/D50"R"4
Loading...