Janam Technologies XM5WB, XM5WA User Manual
p
Model :
XM5
Originator :
Jinny Cho
Version :
1.0
POINT MOBILE CO., LTD.
B-9F, Kabul Great Valley, 32, Digital-Ro 9Gil
Geumcheon-gu, Seoul, Korea 153-709
www.
Dept.
PC/PE/ID/PM/QA
ointmobile.co.kr
Date :
st
Dec 1
, 2014
XM5
User Manual
The Point Mobile name and logo are trademarks of Point Mobile Co., Ltd. in Korea and many other countries.
All rights reserved. This document and any enclosed documents contain confidential or privileged information
belonging to Point Mobile and/or its affiliates. You are hereby notified that any disclosure, copying, distribution
or the taking of any action based on the contents of this information is strictly prohibited.
CONTENTS
1. INTRODUCTION ················································································· 4
Trademarks
About the XM5 Handy Terminal
Accessories
2. SAFETY REGULATIONS HW ·································································· 5
2.1. General Safety Rules ········································································ 6
2.2. Power Supply ·················································································· 6
2.3. Laser Safety ···················································································· 6
2.4. LED Safety ····················································································· 8
2.5. FCC/ EU RF Exposure ······································································ 8
2.6. CB Scheme ····················································································· 9
2.7. FCC Part 15 Regulation ····································································· 9
2.8. Radio Compliance ············································································ 9
2.9. WEEE Compliance ·········································································· 10
2.10. China Compliance ··········································································· 10
2.11. HAZARODUS Locations (USA&Canada) ·············································· 10
2.12. ATEX Directive (Europe) ··································································· 10
2.13. Canadian Compliance ······································································ 10
······························································································· 4
·································································· 4
······························································································· 4
3. GETTING STARTED ··········································································· 12
3.1. Install the Battery ············································································ 12
3.2. Charge the Batteries ········································································ 13
3.3. LED Indicators ················································································ 14
3.4. Guidelines for Battery Pack Use and Disposal ······································· 15
3.5. Turn Your Device On ······································································· 17
3.6. Desktop ························································································· 17
3.7. Indicator Icons ················································································ 18
3.8. Using the Stylus ·············································································· 18
3.9. Selecting Program ··········································································· 19
3.10. Pop-Up Menus ················································································ 19
3.11. Using Windows Explorer ··································································· 19
4. GET TO KNOW YOUR DEVICE ····························································· 19
4.1. Feature of Your Device ····································································· 19
4.2. XM5 Handy Terminal ······································································· 19
4.3. Front Panel Layout ·········································································· 20
4.4. Display Backlight ············································································· 21
4.5. Keypad Backlight ············································································ 20
4.6. Using Screen Protectors ··································································· 22
4.7. Installing Your Screen Protector ························································· 23
4.8. Back Panel Layout ··········································································· 23
4.9. Left Side Panel Layout ····································································· 26
4.10. Installing Memory Cards ··································································· 25
4.11. Right Side Panel Layout ··································································· 26
4.12. Top Panel Layout ············································································ 26
1
4.13. Bottom Panel Layout ········································································ 27
4.14. Peripherals and Accessories ······························································ 28
4.15. USB ActiveSync Cable ····································································· 28
4.16. Li-ion Battery Packs ········································································· 28
4.17. Battery Power ················································································· 29
4.18. Main Battery Pack ··········································································· 29
4.19. Managing Main Battery Power···························································· 29
4.20. Resetting the Terminal ····································································· 30
4.21. Suspend Mode ··············································································· 31
4.22. Memory Allocation ··········································································· 32
4.23. Care and Cleaning of the Products ······················································ 32
4.24. XM5 Technical Specifications ···························································· 32
5. USING THE KEYPAD ·········································································· 33
5.1. Numeric Keypad Layout ···································································· 34
5.2. Navigation Keys ·············································································· 34
5.3. Basic Keys ····················································································· 34
5.4. Alpha/Numeric Modes ······································································ 35
5.5. Alpha Indicators on the Numeric Keys ·················································· 35
5.6. BLUE Key Combinations ··································································· 36
5.7. Program Buttons ············································································· 36
6. USING THE IMAGE ENGINE ································································ 37
6.1. Overview ······················································································· 38
6.2. Available Image Engines ··································································· 38
6.3. Depth of Field ················································································· 38
6.4. Supported Bar Code Symbologies ······················································ 39
6.5. Activating the Engine ······································································· 40
6.6. Using Demos ·················································································· 40
6.7. Decoding ······················································································· 40
6.8. To Decode a Bar Code ····································································· 41
6.9. Sample Bar Codes ·········································································· 41
6.10. Omni-Directional Scanning Positions ··················································· 41
6.11. Capturing Images (IT5300SR Engine Only) ··········································· 42
7. USING THE LASER ENGINE ································································ 42
7.1. Overview ······················································································· 42
7.2. Available Laser Engines ··································································· 42
7.3. Depth of Field ················································································· 42
7.4. Supported Bar Code Symbologies ······················································ 43
7.5. Activating the Engine ······································································· 43
7.6. Using Demos ·················································································· 43
7.7. Decoding a Bar Code ······································································· 43
7.8. Sample Bar Code ············································································ 43
7.9. Scanning Positions ·········································································· 44
8. USING SCANWEDGE ········································································· 44
8.1. Overview ······················································································· 44
8.2. Enabling ScanWedge ······································································· 45
2
9. USING CONTROL PANEL ···································································· 46
9.1. System Properties ··········································································· 45
9.2. Power properties ············································································· 46
9.3. Program Button properties ································································ 47
9.4. Backlight Properties ········································································· 49
9.5. Scanner Settings ············································································· 49
10. COMMUNICATION ············································································ 52
10.1. Communication Options ···································································· 52
10.2. Installing Additional Software ····························································· 53
10.3. Connecting the USB ActiveSync Cable ················································ 53
10.4. ActiveSync Communication ······························································· 54
10.5. Communication Type ······································································· 54
10.6. Hardware Requirements for Setup ······················································ 54
10.7. Software Requirements for Communication ·········································· 55
10.8. Setting Up the Host Workstation ························································· 55
10.9. Communicating with the Handy Terminal ·············································· 55
10.10. Synchronizing with the Host Workstation ·············································· 55
10.11. Exploring the Terminal from the Workstation ········································· 55
10.12. Adding Programs via ActiveSync ························································ 56
10.13. Wireless Radios ·············································································· 56
10.14. Connecting the Terminal to a Wireless Network ····································· 57
10.15. WLAN (802.11b/g/n Radio) ································································ 58
10.16. Adding Programs from the Internet ······················································ 58
11. BLUETOOTH HANDLER ······································································ 58
11.1. Enabling the Bluetooth Radio ····························································· 59
11.2. Connecting to Other Devices ····························································· 59
11.3. Pairing Bluetooth Devices ································································· 59
11.4. Setting Up a Bluetooth Printer ···························································· 59
12. SINGLE SLOT DOCKING CRADLE/SINGLE SLOT ETHERNET CRADLE DEVICE ········· 60
12.1. Overview ······················································································· 60
12.2. Battery Charging ············································································· 60
12.3. Power Supply ················································································· 60
12.4. Front Panel ···················································································· 60
12.5. Back Panel ···················································································· 61
12.6. Powering the Single Slot Docking Cradle or Single Slot Ethernet Cradle Device ····· 62
12.7. Charging theBattery ········································································· 62
12.8. Technical Specifications ··································································· 63
13. SINGLE SLOT DOCKING CRADLE/SINGLE SLOT ETHERNET CRADLE DEVICE ········· 63
13.1. Overview ························································································ 64
13.2. Power Supply ················································································· 64
13.3. Front Panel ···················································································· 64
13.4. Back Panel ···················································································· 65
13.5.. Charging theBattery ········································································· 65
13.6 Technical Specifications ··································································· 66
3
1. Introduction
Thank you for purchasing XM5 handy terminal.
This manual generally provides you with the safety information and basic features and operations of
the XM5 device. Please read all safety precautions and this manual carefully before using your handy
terminals and peripherals to ensure safe and proper use.
Trademarks
The official name of Windows XP is Microsoft Windows XP Operating System.
The official name of Windows Vista is Microsoft Windows Vista Operating System.
The official name of Windows 7 is Microsoft Windows 7 Operating System.
Microsoft, Windows, Windows Embedded Handheld 6.5 Pro, ActiveSync, and the brand names and
product names of other Microsoft products ar e trademarks of Microsoft Corporation in the US and
other countries.
Other company and product names given in this manual or displayed in this software may be th e
trademarks of their respective companies.
About the XM5 Handy Terminal
The new XM5 is the latest generation handy terminal device, combining a pocket sized rugged form
factor built on Microsoft Windows Embedded Handheld 6.5 Pro operating system. The XM5 is designed
for retail warehousing and logistics applications where maximum performance and durability is
required in compact Janam device.
The XM5 handy terminal is available in different models depending on the options.
Accessories
Cradles (including DC 5V 4A Adaptor)
CRD-P1-005U (XM5-Single Slot Cradle)
CRD-P1-005E (XM5-Single Ethernet Cradle)
Batteries
4000mAh Battery Pack, Standard Capacity (60-BTSC)
Power Supply
AC Adaptor, INPUT: AC100~240V 50/60Hz, OUTPUT: DC5V 1.8A with MicroUSB type
Cables
MicroUSB ActiveSync Cable
Others
Stylus Pen and tether
Handstrap
XM5 handy terminal contains the following items basically:
4
• Handy terminal
• MicroUSB ActiveSync Cable
• 5V/1.8A AC Adaptor with MicroUSB type
• AC Plugs
• Battery Pack
• Stylus Pen and tether
• Handstrap
• LCD Screen Protection Film
• Quick Start Guide
☞
NOTE:
caused by improper packaging is not covered under the warranty
☞
NOTE:
the battery packs first. See Paragraph 3.2.
Keep the original packaging for use when sending products to the technical assistance center. Damage
Rechargeable battery packs are not initially charged or discharged. Before you begin to use, you must charge
2. Safety Regulations
Symbols in this manual
In this manual, some important items are described with the symbols shown below. Be sure to read
these items before using this equipment.
WARNING
AVERTISSEMENT Le terme AVERTISSEMENT indique une situation potentiellement dangereuse qui, si elle n'est pas
évitée, peut entraîner la mort, des blessures graves, des dommages importants ou l'incendie d’objets et biens d’équipement
environnants.
Indicates a potentially hazardous situation which, if not avoided, could result in death
serious injury, or serious damage, or fire in the equipment or surrounding objects.
CAUTION
ATTENTION Le terme ATTENTION indique une situation potentiellement dangereuse qui, si elle n'est pas évitée, peut
entraîner des blessures mineures ou modérées, des dégâts partiels à l'équipement, aux objets environnants ou la perte de
données.
☞
NOTE
This section outlines the safety precautions associated with using XM5 handy terminal.
☞
NOTE:
operation. However, as with any electrical equipment, the best way to ensure safe operation is to read this manual
carefully before performing any type of connection to the handy terminal and operate them according to the agency
guidelines described in the manual.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury, partial damage to the equipment or surrounding objects, or loss of data.
Indicates information to which you should pay attention when operating the equipment.
XM5 handy terminals meet or exceed the requirements of all applicable standards organizations for safe
5
2.1.
General Safety Rules
CAUTION
Use only the components supplied by the manufacturer for the specific XM5 being used.
Do not attempt to disassemble the XM5 handy terminal, as it does n ot contain parts that can be
repaired by the user. Any tampering will invalidate the warranty.
When replacing the battery pack or at the end of the oper ative life of the XM5 handy terminal,
disposal must be performed in compliance with the laws in force in your country.
Before using the devices and the battery packs, read this manual carefully.
Do not submerge the XM5 handy terminal in liquid products.
CAUTION
ATTENTION
Utilisez uniquement les composants fournis par le fabricant pour l’utilisation du XM5.
Ne tentez pas de démonter le XM5. Ce produit ne contient aucune pièce ne pouvant être réparée par l'utilisateur. Toute
manipulation fera perdre la garantie au produit.
Lors du remplacement de la batterie ou en fin de vie du terminal portatif XM5, l'élimination et le recyclage doit être effectuée
en conformité avec les lois en vigueur dans votre pays.
Avant d'utiliser les appareils et les batteries, lire attentivement ce manuel.
Ne pas plonger le XM5 dans des produits liquides.
2.2.
Power Supply
The power supply for this device has met applicable KCC/CCC safety requirements.
Please adhere to the following safety instructions per UL guidelines:
• FAILURE TO FOLLOW THE INSTRUCTIONS OUTLINED MAY LEAD TO SERIOUS PERSONAL
INJURY AND POSSIBLE PROPERTY DAMAGE.
• IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS.
WARNING
• DANGER – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE
INSTRUCTIONS.
WARNING
AVERTISSEMENT
DANGER - POUR RÉDUIRE LES RISQUES D'INCENDIE OU DE CHOC ÉLECTRIQUE, VEUILLEZ SUIVRE
ATTENTIVEMENT CES INSTRUCTIONS.
Use only Janam-approved power supply. Use of a non-Janam-approved power supply may be
dangerous and the warranty does not cover damage to the device caused by non-Janam-approved
power supply. The package includes international AC plugs. The AC plu gs must be plugged in the
power supply before the power supply itself is plugged on the wall outlet. The power supply is intended
to be correctly oriented in a vertical or horizontal or floor mount position.
N'utilisez que l'alimentation fournie et approuvée par Janam. L'utilisation de toute autre alimentation peut être dangereuse.
La garantie ne couvre pas les dommages causés à l'appareil par une autre alimentation que celle fournie par Janam.
L’alimentation est livrée avec des adaptateurs AC pour les différentes prises Internationales. Ces prises adaptateur doivent
être installées à l'alimentation électrique avant que cette dernière soit elle-même branchée sur la prise murale. L'alimentation
est destinée à être orientée en position verticale ou horizontale.
2.3.
Laser Safety
CAUTION
6
A Class 2 laser is safe because the blink reflex limit the exposure to no more than 0.25 seconds. It
only applies to visible-light lasers (400–700 nm). Class-2 lasers are limited to 1mW continuous wave,
or more if the emission time is less than 0.25 seconds or if the light is not spatially coherent. Although
staring directly at the laser beam momentarily causes no known biological damage, avoid staring at
the beam as one would with any very strong light source, such as the sun. Avoid that the laser beam
hits the eye of an observer, even though reflective surfaces such as mirrors, etc.
The laser light is visible to the human eye and is emitted from the window indicated in the figure.
ATTENTION
Un laser de classe 2 reste inoffensif pour les yeux. Le réflexe de clignement de l’œil limite l'exposition à 0,25 secondes au
plus. Ceci s’applique uniquement aux lasers de lumière visible (400-700 nm). Les Lasers de Classe 2 sont limités à 1 mW
(onde continue), ou davantage si le temps d'émission est inférieur à 0,25 secondes ou encore si la lumière n'est pas
cohérente dans l'espace. Bien que le fait de regarder directement le faisceau laser ne cause pas de dommage biologique
momentané, il est conseillé d’éviter de regarder le faisceau ainsi que n'importe quelle source de lumière très forte, comme
le soleil. Évitez également que le faisceau laser frappe l'œil d'un observateur, ainsi que toutes surfaces réfléchissantes
environnantes, telles que des miroirs, etc
La lumière laser est visible pour l'œil humain et est émise à partir de la fenêtre indiquée sur la figure.
Laser output window
Laser Light Label
Flash window
Camera window
S/N label
7
If the above laser light label is attached to your device, it indicates the product contains a
laser engine or laser aimer that emits the laser light. The following information is provided to
comply with the rules imposed by international authorities and refers to the correct use of
XM5 handy terminal.
Laser Safety Statement
This product has been tested in accordance with and complies with CDRH 21 CFR 1040.10 and
1040.11 and IEC 60825-1 Ed 2 (2007) except for deviations pursuant to Laser Notice No 50, dated
June 24, 2007. LASER LIGHT. DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCTS. 1 mW MAX
OUTPUT: 650nm.
For installation, use and maintenance, it is not necessary to open the device.
WARNING:
any part of the optics cavity by unauthorized personnel may violate laser safety regulations. The optics system
is a factory only repair item.
Do not attempt to open or otherwise service any components in the optics cavity. Opening or servicing
AVERTISSEMENT : Ne tentez pas d'ouvrir ou d’intervenir de quelque manière que ce soit sur les composants de la
cavité optique. L'ouverture ou l'entretien d'une partie de la cavité optique par des personnes non autorisées pourrait
enfreindre les règlementations liées aux normes de sécurité laser. La réparation du système optique ne peut être
prise en charge que par le personnel qualifié du fabricant.
WARNING:
result in exposure to hazardous visible laser light.
AVERTISSEMENT : Toute manipulation, réglage, ou l'exécution des procédures autres que ceux spécifiés ici
peuvent entraîner une exposition dangereuse à la lumière visible du laser.
WARNING:
microscopes, eye glasses and magnifying glasses.
AVERTISSEMENT : L'utilisation du scanner avec des systèmes optiques tels que jumelles, microscopes, lunettes
de vue et autres loupes, augmente les risques de dommages pour les yeux.
2.4.
The LED output on this device has met IEC62471 LED safety and certified to be under the limits of a
CLASS 1 LED product.
2.5.
LED Safety
FCC/EU RF Exposure
Body effects
This device complies with FCC/EU RF exposure guidelines set forth for an uncontrolled environment.
For body worn operation, this device has been tested and meets the RF ex posure guidelines for use
with an accessory that contains no metal and the positions the handset a minimum of 1.0 cm (0.39
inch) from the body. Use of other enhancements may not ensure compliance with RF exposure
guidelines. If you do not use a body-worn accessory and are not holding the device at the ear, position
the handset a minimum of 1.0 cm (0.39 inch) from your body when the device is switched on.
Belt-clips, holsters, and similar accessories containing metallic components from others manufacturers
should not be used.
Accessories worn close to the body, without keeping a minimum distance of 1 cm (0.39 inch) between
the user's body and the device, and that have not been tes ted for typical body operation, may not
comply with FCC's RF exposure limits and should be avoided.
.
Use of controls or adjustments or performance of procedures other than those specified herein may
Use of optical systems with the scanner will increase eye hazard. Optical instruments include binoculars,
8
2.6.
This device complies with CB Scheme IEC 60950-1
CB Scheme
2.7.
Pursuant to part 15 of the FCC Rules, you are cautioned that changes or modificati ons not expressly
approved by Janam could void your authority to operate the XM5 handy terminal.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or tel evision
reception, which can be determined by turning the equipment off and on, the user i s encouraged to
try to correct the interference by one or more of the following measures:
2.8.
XM5 RF terminals are in conformity with all essential requirements of the R&TTE Directive (1999/5/EC).
FCC Part 15 Regulation
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Conn ect the equipm ent into an outlet on a cir cuit different fr om that to which the re ceiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
In accordance with FCC 15.21, changes or modifications not expressly approved by the party
responsible for compliance could void the user‘s authority to operate the equipment.
The antenna(s) must not be co-located or operating in conjunction with any other antenn a or
transmitter. To maintain compliance with FCC/EU RF exposure guidelines for body-worn
operation, do not use accessories that contain metallic components. .
Radio Compliance
This device is marked with in accordance with the Class II product requirements
specified in the R&TTE Directive, 1999/5/EC. The device is intended for use throughout the European
Community; PAN European Frequency Range: 2.402 ~ 2.480 GHz.
Restrictions for use in France are as follows:
• Indoor use: maximum power (EIRP*) of 100 mW for the entire 2.400 ~ 2.4835 GHz
• Outdoor use: Maximum power (EIRP*) of 100 mW for the 2.400 ~ 2.454 GHz band and
maximum power (EIRP*) of 10 mW for the 2.454 ~ 2.483 GHz band.
The CE mark on the device indicates that the system has been tested to and confirm with the
provisions noted within the 2004/108/EC Electromagnetic Compatibility Directive and the
2006/95/EC Low Voltage Directive,
1999/5/EC (R&TTE), and 2011/65/EU (RoHS)
.
9
Janam shall not be responsible for use of our product with equipment (i.e., power supplies,
personal computers, etc.) that is not CE mar ked and does not comply with the Low Voltage
Directive.
2.9. WWAN
In radio systems configured with mobile computers and access points , the frequencies to be used
must be allowed by the spectrum authorities of the specific country in which the installation takes
place. Be absolutely sure that the system frequencies are correctly set to be compliant with the
spectrum requirements of the country. The Radio modules used in this product automatically adapt
to the frequencies set by the system and do not require any parameter settings .The TYPE field shows
the correspondence between XM5 types and radio modules:
HSPA
HSPA, or Evolved High-Speed Packet Access, is a technical standard for wireless, broadband
telecommunication. HSPA enhances the widely used WCDMA (UMTS) based 3G networks with higher
speeds for the end user.
2.10. WEEE Compliance
Information for the user in accordance with the European Commission Directive
2012/19/EU of the European Parliament and of the Council of 4 July 2012 on Waste
Electrical and Electronic Equipment (WEEE)
This product has required the extraction and use of natural resources for its production. It may contain
hazardous substances that could impact health and the environment, if not properly disposed. In
order to avoid the dissemination of those substances in our en vironment and diminish the pressur e
on the natural resources, we encourage you to reuse, recycle and recover the product. If the product
is disposed according to the Directive, it will avoid potentially negative consequences to the
environment and human health which otherwise could be caused by incorrect disposal.
The product marked with crossed out wheeled bin must be disposed separately from municipal
waste.
For more detailed information about disposal, reuse, and recycle system, contact your local or regional
waste administration.
2.11.
HAZARODUS Locations (USA&Canada)
XM5 terminals are in conformity with all essential requirements of the HAZARODUS Locations.
According to definitions in the
and
60079-10
result from the presence of:
Flammable gases, vapors or liquids (known as Class I)
Combustible dusts (Class II)
Ignitable fibers or flyings (Class III)
North American Hazardous Location Approval
CENELEC EN 60079-10,
Canadian Electrical Code, U.S. National Electrical Code, IEC
hazardous locations are defined when fire or explosion may
10
The following information applies when operating this equipment in hazardous locations:
XM5 marked “Class I, Division 2, Groups A, B, C and D” are suitable for use in Class I Division 2 Groups
A, B, C, D, Hazardous Locations and nonhazardous locations only. XM5 is supplied with markings on the
rating nameplate indicating the hazardous location temperature code. When combining products within a
system, the most adverse temperature code (lowest “T” number) may be used to help determine the
overall temperature code of the system. Combinations of equipment in your system are subject to
investigation by the local Authority Having Jurisdiction at the time of installation.
2.12. ATEX Directive (Europe)
The ATEX requirements
The ATEX directive requires the following major elements to be met in order to apply the ATEX marking:
The CE mark - The CE mark is a self-declaration marking indicating that your equipment conforms
to applicable technical provisions and ATEX requirements and other directives.
Essential health and safety requi rements - Annex II of the ATEX directive, requires that you
establish principles of integrated explosion safety from all electrical and non-electrical ignition
sources. You can demonstrate compliance to these requirements by following the harmonized
European standard series
EC Type Examination Certificate - For Category 1 (electrical and mechanical) and Category 2
(electrical) equipment, a Notified Body will need to verify that your equipment has met the relevant
applicable provisions of the ATEX directive in order to receive an EC Type Examination Certificate.
For Category 3 equipment, an EC Type Examination Certificate is not required,
however, manufacturers must ensure that your products comply with ATEX by following the
appropriate conformity route.
Quality Assessment - The facility(s) producing your equipment must undergo a Quality
Assessment of
Notification (QAN).
EN13980
EN 60079
which will result in a Notified Body issuing you a Quality Assurance
.
2.13. Canadian Compliance
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed
below with the maximum permissible gain and required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated
for that type, are strictly prohibited for use with this device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p) is not more than that necessary for successful communication.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
11
(1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les typesd'antenne énumérés cidessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non
inclus dans cette liste,ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un
type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques
de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
3. Getting Started
3.1. Install the Battery
The HANDY TERMINAL is shipped with the battery packaged separate from the unit. Follow the
steps below to install the battery.
1. Remove the battery compartment door by moving the Battery door’s locks up.
Rib of
hanging
Battery door lock Up
2. Insert the battery well with the battery cells facing top.
12
1
3. Replace the battery door to start from bottom to top door’s lock downwards.
2
2
1
☞
NOTE:
☞
NOTE:
AVERTISSEMENT : Utilisez uniquement des batteries Lithium-Ion approuvés par Janam. Toute autre batterie peut
entraîner des dommages non couverts par la garantie.
3.2.
Two points of Battery guide stopper must be pertinently inserted to rear cover battery guide stopper hole
The battery door must be installed prior to booting the unit.
WARNING:
covered by the warranty.
Use only Janam-approved Li-Ion battery packs. Unauthorized battery may result in damage not
Charge the Batteries
Handy Terminals ship with only main battery pack significantly charged of power. Charge the main
battery pack with the Handy Terminal charging cable for a minimum of 4 or 6 hours depending
on your battery before initial use.
1. Attach the appropriate plug adapter to the plug of the power cable.
2. Insert the plug into the appropriate power source.
Plug the Handy Terminal power cable into the USB Jack on the side end of the unit.
13
WARNING:
cables, or power adapters may cause batteries to explode or damage your device.
DO NOT attempt to charge damp/wet handy terminals or batteries. All components must be dry before connecting
to an external power source.
Batteries must be charged at a temperature ranging from 0~45℃ (±3℃). If you don’t follow the guide, it might
have a harmful effect on the battery life.
AVERTISSEMENT : Veillez à n’utiliser que les périphériques approuvés par Janam (câbles d'alimentation et
adaptateurs électriques). Tout périphérique non autorisé (câble ou adaptateur) peut provoquer l’explosion de la
batterie ou endommager votre appareil.
NE PAS tenter de recharger les terminaux ou les batteries encore humides lorsqu’ils ont été mouillés. Tous les
composants doivent être impérativement séchés avant la connexion à une source d'alimentation externe.
Les batteries doivent être chargées à une température allant de 0~45°C (± 3°C). Le non-respect de ces
recommandations pourrait avoir un effet néfaste sur la durée de vie de la batterie.
CAUTION:
that plug in use, it is possible to break the power code.
ATTENTION: Après une période de charge de la batterie, veillez à débrancher le connecteur du chargeur. Une
utilisation prolongée de celui-ci risquerait d’endommager le cordon d’alimentation.
Use only Janam-approved peripherals, power cables, and power adapters. Unauthorized peripherals,
After the battery has been charged, disconnect the DC Power Jack from the terminal. If you stay on
☞
NOTE:
them.
☞
NOTE:
charged battery pack before the battery completely discharges.
Rechargeable battery packs are not initially charged. Therefore the first operation to perform is to charge
If you remove the battery pack or it completely discharges, you have 30 minute window of time to insert a
3.3.
LED Indicators
The red LED is ON while charging the battery and the green LED is ON when the battery is fully
charged.
14
Alternatively, it is also possible to recharge the battery pack by using the single slot cradle, the single
Ethernet cradle or the 4-slot battery charger.
During the charging process the LED positioned at the upper side of the display is red constant. Once
the charging process has been completed this LED is green constant.
If the battery pack is removed from the handy terminal, it can be r echarged by inserting it into the
rear slot of the single slot cradle, the single Ethernet cradle or the 4-slot battery charger.
3.4.
Guidelines for Battery Pack Use and Disposal
The following are general guidelines for the safe use and disposal of batteries:
Store the terminal and the spare batteries between 20 to 30 ºC (68 to 86 ºF) in order to
maintain optimal battery performance.
Standard batteries must be charged at a temperature ranging from 0 to 45℃ (±3℃).
The battery level may not be displayed correctly for some minutes after the disconnection if
the handy terminal is disconnected from power supply before the charging cycle is completed.
The handy terminal could get warm during charging. This is normal and does not mean a
malfunction.
To achieve the best battery life, turn off the radios not in use.
Rechargeable battery packs is not initially charged. Therefore the initial operation to perform is
to charge them. See below.
By default, the battery pack is disconnected at the factory to avoid damage due to excessive
draining. Annual replacement of rechargeable battery pack avoids possible risks or
abnormalities and ensures maximum performance.
WARNING:
before connecting to an external power source.
AVERTISSEMENT : NE PAS tenter de recharger les terminaux ou les batteries encore humides lorsqu’ils ont été
mouillés. Tous les composants doivent être impérativement séchés avant la connexion à une source d'alimentation
externe.
WARNING:
to local guidelines.
AVERTISSEMENT : Ne jetez pas une batterie usagée à la poubelle. Elle contient des métaux lourds et doit être
recyclée conformément aux directives locales.
WARNING:
avoided.
Only in case of long storage, in order to avoid deep discharge of the battery, it's recommended to partially
recharge the battery every two-three months to keep the charge status at a medium level.
AVERTISSEMENT : Le stockage des batteries (à pleine charge ou complètement déchargée) pendant de longues
durées doit être évité.
Pour éviter une décharge profonde de la batterie en cas de stockage de longue durée ; il est recommandé de
recharger partiellement la batterie tous les deux à trois mois pour maintenir l'état de charge à un niveau moyen.
WARNING:
this manual.
The battery pack may get hot, explode, ignite, and/or cause serious injury if exposed to abusive conditions.
If the battery pack is replaced with an improper type, there is risk of explosion.
DO NOT attempt to charge damp/wet handy terminals or batteries. All components must be dry
Never throw a used battery in the trash. It contains heavy metals and should be recycled according
Storage of batteries for long time at fully charged status or at fully discharged status should be
Installing, charging and/or any other action should be done by authorized personnel and following
15
Do not place the battery pack in or near a fire or heat; do not place the battery pack in direct sunlight, or use or
store the battery pack inside unventilated areas in hot weather; do not place the battery pack in microwave ovens,
dryer, high pressure containers, on induction cookware or similar device. Doing so may cause the battery pack to
generate heat, explode or ignite. Using the battery pack in this manner may also result in a loss of performance
and a shortened life expectancy.
Use only a Janam approved power supply. The use of an alternative power supply will void the product warranty,
may cause product damage and may cause heat, explode or ignite.
The area in which the units are charged should be clear of debris and combustible materials or chemicals.
Do not use the battery pack in any other manner outside its intended use in Handy Terminal and peripherals.
AVERTISSEMENT : L’installation, la charge et/ou de toute autre action doit être effectuée par du personnel autorisé
après lecture de ce manuel.
En cas d'utilisation dans des conditions abusives, la batterie peut chauffer, exploser, s'enflammer et/ou causer des
blessures graves.
L’utilisation d’une batterie inappropriée peut résulter un risque d’explosion
N’exposez pas la batterie au feu ou près d’une source de chaleur; ne placez pas la batterie en plein soleil.
Par temps chaud, n’utilisez ou ne stockez pas la batterie dans des zones non ventilées.
Ne placez pas la batterie dans un four à micro-ondes, un sèche-linge, un conteneur à haute pression, sur une
batterie de cuisine à induction ou tout dispositif similaire. La batterie pourrait chauffer, exploser, s'enflammer ou
entraîner une perte de performance avec pour conséquence une espérance de vie réduite.
N’Utilisez que le bloc alimentation fourni et approuvé par Janam. L'utilisation de tout autre alimentation pourrait
engendrer des dommages au produit et provoquer une surchauffe, allant jusqu’à l’explosion ou l'enflammement, et
causer la perte de la garantie.
Le local dans lequel les terminaux sont rechargés doit être propre et sans aucune présence de matériaux
combustibles ou de produits chimiques.
Ne pas utiliser la batterie en dehors de l’utilisation prévue pour le terminal portable.
WARNING
Do not short-circuit the battery pack contacts connecting the positive terminal and negative terminal. This might
happen, for example, when you carry a spare battery pack in your pocket or purse; accidental short–circuiting can
occur when a metallic object such as a coin, clip, or pen causes direct connection of the contacts of the battery
pack (these look like metal strips on the battery pack). Short–circuiting the terminals may damage the battery pack
or the connecting object.
Do not apply voltages to the battery pack contacts.
Do not pierce the battery pack with nails, strike it with a hammer, step on it or otherwise subject it to strong
impacts or shocks.
Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The battery pack contains safety and
protection devices, which, if damaged, may cause the battery pack to generate heat, explode or ignite.
In case of leakage of liquid from the battery, avoid contact with liquid the skin or eyes. If the contact occurs,
immediately wash the affected area with water and consult a doctor.
Do not solder directly onto the battery pack.
Do not expose the battery pack to liquids.
Avoid any knocks or excessive vibrations. If the device or the battery is dropped, especially on a hard surface,
you should take it to the nearest Authorised Repair Centre for inspection before continuing to use it.
Do not replace the battery pack when the device is turned on.
Do not remove or damage the battery pack’s label.
Do not use the battery pack if it is damaged in any part.
Battery pack usage by children should be supervised.
Collect and recycle waste batteries separately from the device in comply with European Directive 2006/66/EC,
2011/65/EU, 2012/19/EU and subsequent modifications, US and China regulatory and others laws and regulations
about environment.
AVERTISSEMENT : Ne mettez pas les contacts de batterie en court-circuit en connectant la borne positive et la
borne négative. Cela peut se produire, par exemple, lors du transport d’un pack de batterie de rechange dans votre
poche ou un sac. Un court-circuit accidentel peut se produire si un objet métallique provoque la connexion directe
des contacts de la batterie. Un court-circuit risque d'endommager la batterie ou l'élément de connexion.
Ne pas appliquer de tension sur les contacts de batterie.
16
Ne pas percer la batterie avec des objets pointus, la soumettre à l’écrasement ou à des chocs violents.
Ne pas démonter ou modifier la batterie (en la pliant, l’écrasant ou la déformant). Celle-ci contient des dispositifs
de sécurité et de protection, qui, s'ils sont endommagés, peuvent entraîner un échauffement excessif allant jusqu’à
provoquer, son explosion ou son enflammement.
En cas de fuite du liquide contenu dans la batterie, évitez tout contact sur la peau ou les yeux. Si toutefois un
contact se produit, lavez immédiatement la zone affectée avec de l'eau et consulter un médecin.
Ne pas souder directement sur la batterie.
Ne pas exposer la batterie à des liquides.
Eviter les chocs et les vibrations excessives. En cas de chute du terminal ou de sa batterie, en particulier sur une
surface dure, il est instamment demandé de contacter le centre de réparation agréé le plus proche pour inspection
et vérification de son état normal de fonctionnement.
Ne pas remplacer la batterie lorsque l'appareil est allumé.
Ne pas retirer ou endommager l'étiquette de la batterie.
Ne pas utiliser la batterie si elle est endommagée d’aucune manière que ce soit.
L’utilisation d’une batterie rechargeable par des enfants doit être supervisée par un adulte.
La Collecte et le recyclage des piles et batteries doit être faite en conformité avec la directive européenne 2006/66
/ CE 2011/65 / UE 2012/19 / UE et ses modifications ultérieures. Elle doit également répondre aux lois et
réglementations sur l’environnement, en vigueur aux Etats-Unis et en Chine
☞NOTE:
terminal checks the battery energy level. If the battery is not sufficiently charged, handy terminal does not turn on.
In this case, either substitute the battery pack with a charged one (sufficiently charged) or insert handy terminal into
a powered cradle or plug it into the direct power supply.
In order to guarantee an adequate operating autonomy, when replacing the battery pack the handy
3.5. Turn Your Device On
If you apply the power to your device, it turns on by itself. Do NOT press any keys or interrupt while
turning on process.
When the process is complete, the Desktop appears, and the terminal is ready for use.
3.6. Desktop
☞NOTE:
Desktop on the popup menu
Tap the touch screen once to zoon in the upper menu
You can access the Desktop any time by tapping the Change Views icon in the command bar and selecting
17
3.7.
Indicator Icons
The command bar, located at the upper of application screens, provides access to many system
functions and programs.
Icons Meaning
Open the start menu
Access the Wireless Manager
Open the Scanner option menu
Indicates the Keypad value
Shows phone signal mode
Shows the volume
Indicates the Battery Control Panel (CPL)
Indicates Clock & Alarm CPL
zoom in/ out
Access the Bluetooth radio
Left and right arrows are used to scroll through additional icons
Icon Meaning
Indicates AC connection mode
Indicates WAN (Phone) connection mode
Indicates Sound connection mode
Indicates LAN / Bluetooth mode
Indicates Keypad mode
3.8.
Using the Stylus
18
The terminal comes with a stylus included in a loop on the Lanyard. Use this stylus (or your finger)
to select or enter information on the touch screen. The stylus functions as a mouse; generally, a tap
is the same as a click.
Tap Tap the touch screen once to open menu items and select options.
Drag Hold the stylu s on the screen and drag across the screen to select text and images.
Tap & hold Tap and hold the stylus on an item and a pop-up menu appears. On the pop-up menu, tap
the action of the task you want to perform.
WARNING:
panel and may cause damage not covered by the warranty.
AVERTISSEMENT : L'utilisation d'objets, tels que trombones, crayons, stylos à encre sur l'écran tactile peut
l’endommager et causer des dommages non couverts par la garantie.
3.9.
Tap Start -> Programs. To open a program, tap the icon on the menu.
3.10.
You can quickly choose an action for an item using the pop-up menus.
1. Tap and hold the stylus on the item name. The pop-up menu appears.
2. Lift the stylus and tap the action you want to perform.
The contents of pop-up menus change according to the program you are using.
Selecting Program
Pop-Up Menus
Use of objects, such as paper clips, pencils, or ink pens on the touch screen can damage the input
3.11.
Use Windows Explorer to navigate through the files on your system. Start menu -> File explorer
Move files by tapping and holding on the file, and then tapping Cut, Copy or Paste on the pop-up
menus that appear.
Using Windows Explorer
4. Get to Know Your Device
4.1.
The following list outlines a few of the feature included in your device.
4.2.
Operating Systems: Microsoft Windows Embedded Handheld 6.5 Pro
Micro Processor: Cortex-A8 1GHz
RAM Memory: 512MB
FLASH Memory: 1GB
Feature of Your Device
XM5 Handy Terminal
19
3.5” VGA Display: 480x640 Transmissive TFT
Industrial Grade Touch Screen
Keyboards: Numeric, Qwerty
Micro SDHC Expansion Memory Card Interface: Support up to 32 GB
Power Supply : MicroUSB power adaptor
Scan Engine:
Battery: Li-ion battery, 3.7V/4000mAh/14.8Wh
IP65 certified enclosures
Audio: Integral Microphone, Earpiece, Loud Speaker, 3.5pi 4pole Jack for Ear-Mic headset
BT: Bluetooth Radio 2.1+EDR with Internal Antenna
WLAN: 802.11 a/b/g/n Radio with Internal Antenna
Notification LEDs
Notification Vibration Motor
Camera : 5M pixel CMOS camera with AutoFocus and LED flash
Sensors : Proximity sensor and Acceleration sensor
GSM/GPRS/EDGE : Quad band, 850/900/1800/1900MHz
UMTS/HSPA: Five band, 800/850/900/1900/2100MHz
GPS: Assisted GPS
NFC : 13.56MHz HF, ISO14443A, ISO14443B & ISO15693 are supportive
Interfaces : Micro-USB connector : USB 2.0 High Speed
HandyLink connector: USB 2.0 High speed Client, Host (USB Host for Ethernet Cradle),
4.3.
Charging
• 1D engine: N4313
• 2D engine: N560X
1) Power indications, 2) Scan reading indications & OS notifications
Front Panel Layout
Proximity sensor
LED
Receiver
Touch screen
display
Scan key
Keyboard
(32-key numeric)
20
Loading...