Janam Technologies RFD T1 002UL User Manual
Certification
his device complies with part 15 of the FCC Rules. Operation
“T
is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation. ”
“This equipment has been tested and found to comply with the limits for a Class A digital device,
rsuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
pu
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accorda
nce with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
nterference in which case the user will be required to correct the interference at his own expense.
i
Changes or modifications not expressly approved by the manufacturer (or party responsible) for
compliance could void the user’s authority to operate the equipment.
RF Exposure
This device complies with RF exposure requirement.
For European Community Users
We have included this bulletin to comply with Directive
2012/19/EU OF THE EURPOEAN PARLIAMENT AND OF THE
COUNCIL of 4 July 2012 on Waste Electrical and Electronic
Equipment (WEEE)
This product has required the extraction and use of natural
resources for its production. It may contain hazardous substances
that could impact health and the environment, If not,
properly disposed.
In order to avoid the dissemination of those substances in our
environment and diminish the pressure on the natural resources,
we encourage you to use the appropriate take-back systems for
product disposal.
Those systems will reuse or recycle most of the materials of the
product you are disposing in a sound way.
The crossed out wheeled bin symbol inform you that the
product should not be disposed of along with municipal
waste and invites you to use the appropriate separate
take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling
system, please contact your local or regional waste administration.
You can also contact your supplier for more information on the
environmental performances of this product.
CE Compliance (for EU only)
This product is labeled with the CE mark in
accordance with the provisions of the applicable
RoHS Directive 2011/65/EU for this product and the
electric accessories.
Contents
UHF RFID Sled
Handstrap
US PlugAC/DC Adapter (5V2A)
USB Type-C Cable
Hardware Overview
1. UHF RFID Antenna
2. Trigger
3. Power Key
4. Mode Change Key
5. USB Type-C Connector
6. LED Indicator
UHF RFID Sled for XT2/XT2+
Quick Start Guide
Hand Strap
Charging the UHF RFID Sled
The UHF RFID Sled and XT2/XT2+ are charged individually.
Charge the UHF RFID Sled by inserting the USB Type-C
cable to the connector. The UHF RFID Sled is fully
charged when the charging LED turns solid green.
<Caution>
Use only Janam batteries and recharge batteries using
only Janam approved charging accessories. Follow all
usage, charging and maintenance guidelines in the
Product User Guide. If you have questions, contact Janam.
Technology at Work.
®
Rev.01
LED Indicator
Demo App Installation
Specifications
Item Specifications
Frequency
Protocol
Output
USB
Bluetooth
HID
LED
Button
Buzzer
Configurations
Size
Battery
Battery Charge
Time
Drop
Adaptor
Weight
UHF 900MHz
ISO 18000-63(18000-6C) / EPC global Class 1 Gen 2
Max. 30 dBm(1Watt), 1dBm unit
USB Type C / USB to Serial Communication
Bluetooth v4.1(Classic + Low Energy) / SSP Profile
HID support
LED(Charge / Power / Sync / Status)
Power, Mode
Max, Min, Mute
RFID only or RFID with 2D scanner(Optional)
70 x 139 x 115.8mm(W x H x D)
3,350 mA, 3.6V Li-ion
AC : About 4H(5V/1.4A)
PC USB : About 8H(USB 2.0, 5V/500mA)
1.5M
5V / 2A
350g
1. Charging LED
2. Power LED
3. Mode LED
4. Status LED
Solid Red
Solid Green
Solid Red
Blinking Red
Solid Green
Blinking Green
Solid Orange
Blinking Orange
Red
Green
Orange
Red
Green
Bluetooth Pairing
Battery is charging
Battery is charged
Power is On
Power is low
BT is connected
BT is connected and power is low
USB connected to PC
USB connected to PC and battery is low
BT SPP connected
BT HID connected
Connected to BT pairing app or USB
connected
UHF RFID ready
Barcode scan ready
1. Search ‘UHF RFID Sled’ from the Google Play Store
Install Demo
2.
App
RFID Tag Decoding
1. Pair the UHF RFID Sled with the XT2 or XT2+
using Bluetooth.
2. Launch the UHF RFID Sled Demo App.
1. Aim the device at the RFID tag.
2. Press the trigger to read the RFID tag.
www.janam.com
Technology at Work.
®
Loading...