
Copyright 2010 Janam Technologies LLC. All rights reserved.
Products or services mentioned may be trademarks or registered trademarks of their respective companies.
Janam Technologies LLC assumes no responsibility for any damage or loss resulting from, or in connection with the use
or application of any product. Janam Technologies LLC assumes no responsibility for any loss or claims by third parties
which may arise through the use of this product. Janam Technologies LLC assumes no responsibility for any damage or
loss caused by deletion of data as a result of malfunction, dead battery or repairs. Be sure to make backup copies of all
important data on other media to protect against data loss.
Contents of this guide are subject to change. For the most current version, visit www.janam.com
+1.877.JANAM.99
www.janam.com
Four-Slot Cradle Kit Quick Start Guide

To help you get started with your Four-Slot Cradle Kit (CKT-P4-00#U), this guide features:
- Hardware Overview
- Getting Started
- Regulatory Information
For additional product details, visit www.janam.com
Content and Additional Resources

3
1
4
5
6
7
Four-Slot Cradle Kit Hardware Overview
1. Cradle (CRD-P4-00#U)
2. Power Supply (PS-XP-4)
3. Line Cord*
4. USB Cable*
5. Power Receptacle
6. USB Type B Port
7. Synch Button (not shown)
8. Cradle Cups
* Comes with cradle kit.
Not separately orderable.
8

Getting Started
A. SET UP
We recommend you turn your computer off before connecting the cradle. After following the steps below, turn
the computer back on.
1. Connect the power supply and line cord.
2. Plug the power supply into the power supply receptacle on the cradle.
3. Connect the USB cable to the cradle.
4. Plug the USB cable into one of your computer’s USB ports.
5. Plug the cradle’s power supply into a power outlet.
C. INSERTING A DEVICE INTO THE CRADLE
Place a mobile device in a cradle cup. The device will automatically seat and join with cradle connectors.

Regulatory Information
For European Community Users
Janam Technologies complies with Directive 2002/69/EC of THE EUROPEAN PARLIAMENT AND OF THE COUNCIL
OF 27 January 2003 on waste electrical and electronic equipment (WEEE).
Waste Electrical and Electronic Equipment Information
This product has required the extraction and use of natural resources for its production. It may contain hazardous
substances that could impact health and the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment and to diminish the pressure on
the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those
systems will reuse or recycle most of the materials of the product you are disposing in a sound way.
The crossed out wheeled bin symbol informs you that the product should not be disposed of along with
municipal waste and invites you to use the appropriate separate take-back systems for product disposal.

The four-slot cradle was evaluated to the following standards and found to be in compliance with the standard
requirements.
UL 60950-1:2003
CSA C22.2 60950-1:2003
EN 60950-1
EN 55022:2006 Class B
EN 55024
EN 61000-3-2:2000 + A2: 2005
EN 61000-3-3:1995 + A1: 2001
EN 61000-4
EN 61000-4-2
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These rules are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy, and if not installed and used
in accordance with the instructions, may cause harmful interference with radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-8
IEC 61000-4
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-11
IEC-003, Issue 4: 2004 Class B