Janam XG100WM Series User Manual
XG100WM User Guide
Version 4
April, 2012
XG100WM User Manual
1
Introduction
Janam’s XG100WM Series has been optimized to meet the unique requirements of mobile workers in
warehouses, distribution centers, loading docks and other operating venues where rugged gun-shaped mobile
computers are deployed. While its center-weighted ergonomic design makes it uniquely balanced and light,
the Microsoft Windows-based XG100WM is a powerful workhorse that delivers state-of-the-art computing
performance in an exceptionally rugged package. Designed for the work at hand, the XG100WM delivers
superior performance and flexibility at a great price.
About the Janam XG100WM
The XG100WM has a light, sleek, highly-functional form factor for intensive barcode scanning. Its unique
center-weighted ergonomics, with battery located in the handle make it light and balanced in the hand. It
features a color, quarter-VGA display, Marvell XScale PXA320 624MHz processor, robust 802.11 b/g
Summit WLAN radio with Cisco’s CCX v4 support. It has an extra-wide keypad area with large, easilydepressed buttons and superior backlighting. The XG100WM meets IP64 sealing requi r ements, withstands
multiple 6’ drops to concrete on all sides across a wide temperature range and 2,000 tumbles in a rotating
test chamber.
Further enhancing its value, the XG100WM features integrated 1D barcode scanning as well as built-in 2D
barcode scanning capability. Janam’s 2D scanning solution enables users to upgrade barcode scanning
capability from 1D to 1D/2D on any device at any time with a simple firmware upgrade. With Adaptus®
Imaging Technology, the XG100WM easily reads all types of barcode symbologies including linear,
stacked and 2D. It offers the flexibility to adapt as business needs change, without the need to invest in
new hardware.
Features
•
Microsoft
•
Full 3.7” color display
•
High-performance 1D and 2D barcode scanning capability
•
Extra-wide keypad area with large, easily-depressed buttons and superior backlighting
•
Emulator keypads insuring compatibility with existing installations
•
Vibrator alert for successful scan feedback
•
Bright-LED tail lights for visual feedback during overhead scanning
•
Superior audio performance and VOIP-ready
•
Integrated Electronic Article Surveillance (EAS) tags for enhanced asset protection
•
256MB DDR SDRAM/ 256MB NAND Flash ROM
•
NAND flash backup of OS, applications and user data
•
User accessible microSD card slot
•
Sealed to IP64 standards
•
Rugged design: Withstands multiple 6’ drops to concrete on all sides across wide temperature range and
2,000 tumbles in a rotating test chamber.
•
Enterprise-class WLAN with WPA security protocols
•
Bluetooth v2.0
•
Full system of accessories
®
Windows® Mobile 6.1.
Janam Technologies LLC
1-1
Hardware Overview
2 Programmable keys
Escape key
Control key
Barcode Scan
Window
Scan Trigger
Front View
XG100WM User Manual
Top View
LCD
Microphone
LED Indicators
Power On/Off
Function key
Navigation keys
Syncing/Charging
Rear View
Syncing/Charging
Connector
Rear LED Indicators
Gun Handle
(Battery
Compartment)
Battery Chamber
Janam Technologies LLC
1-2
Speaker
(on bottom
housing)
Battery
Chamber
XG100WM User Manual
Bottom View
Battery
Battery Lock
MicroSD Card Slot
Compartment
Rear LED Indicators
Upper Handstrap Connectors
Janam Technologies LLC
1-3
XG100WM User Manual
Side View
Scan
Window
Scan
Trigger
Upper Handstrap
Connectors (left and
right side)
Handle/
Battery
Chamber
Lower Handstrap
Connector
Base of Battery &
Battery Release
Plunger
Rear-Bottom Sectional View
MicroSD Memory
Card Door
Upper Handstrap
Connectors
Speaker
MicroSD Memory
Card Door Screws
Syncing/Charging
Connector
Rear Indicator Lights
(Tail Lights)
Janam Technologies LLC
1-4
XG100WM User Manual
Get Started
Unpack your Janam XG100
Make sure you have the following:
• Janam XG100WM mobile computer
• Janam authorized battery
• Handstrap
• Stylus
• Stylus tether
• Charging accessory (one of the following kits ordered/packed separately):
- Single-slot cradle kit
- Four-slot cradle kit
- USB cable with AC adapter
- Serial cable with AC adapter
Recommended Host Computer Configuration/Requirements
IBM-compatible host computer with Pentium 450 MHz processor or higher
Microsoft Windows XP or Microsoft Windows 2000 operating system
128 MB RAM
100 MB available hard disk space
CD-ROM drive
One available serial or USB port
Mouse
Janam XG100 SDK
The Janam XG Series Software Development Kit enables programmers to develop applications for Janam
XG Series rugged mobile computers running the Microsoft® Windows Mobile 6.1 operating system. It
contains all necessary details and instructions for developing applications that access Janam XG Series
libraries, including scanning, imaging and hardware utilities.
The development kit, which can be downloaded from Janam’s Partnerzone site (login required) is designed
for use with Microsoft® Windows Mobile 6 SDK or Microsoft Visual Studio 2005.
Update your Desktop Software
Microsoft ActiveSync 4.5 or later software is available at the Microsoft web site at
http://www.microsoft.com
2
Janam Technologies LLC
2-1
XG100WM User Manual
Attach the Handstrap to the XG100WM
1. Push the long-looped end of the handstrap through the left- or right-side upper handstrap connector (at
the back of the handheld).
2. Push the metal hook (the other side of handstrap) through the loop that comes through the upper
handstrap connecter in step 1.
3. Pull the entire length of the handstrap through the loop to fasten one end of the handstrap to the device.
4. Clip the metal hook to the lower handstrap connector (near the base of the handle).
Attach the Stylus Tether to the Stylus
1. Push one looped end of stylus tether through the hole at the top of the stylus.
2. Pull the other end of the stylus tether through the first looped end.
3. Pull the entire length of the stylus tether including the silver grommet all the way through the loop to
fasten and secure the tether to the stylus.
Janam Technologies LLC
2-2
XG100WM User Manual
Attach the Stylus Tether to the Handstrap
1. Push the loop of the loose end of the stylus tether through one of the slits in the handstrap adjustment
slider.
2. Push the stylus (now attached to the stylus tether) through the stylus tether’s loop that comes through
the slit on the adjustment slider.
3. Pull the entire length of the stylus tether and the stylus tether’s silver grommet all the way through the
loop to secure the stylus tether to the handstrap’s adjustment slider.
4. When not in use, the stylus can be inserted in the stylus pouch on the handstrap.
Janam Technologies LLC
2-3
XG100WM User Manual
Install the Battery
IMPORTANT Battery Warning!
CAUTION: Use only Janam-approved batteries.
There is the risk of explosion if battery is replaced by an incorrect type.
Always dispose of used batteries according to the instructions.
INSTALLING THE BATTERY:
1. Insert the top of battery into chamber opening and gently slide battery into battery chamber.
Do not force past point of resistan ce.
2. Turn the battery so that th e base of the battery is perpendicular to the device handle.
This aligns the battery notches with the battery chamber which is required to insert the battery. Once the
battery is properly aligned with the handle, press the battery into the battery c hamber.
3. Turn the battery base c lockwise until t he base of t he battery is par allel with the device. The battery re lease
plunger will click and lock the battery into place.
REMOVING THE BATTERY:
1. To remove the battery, fully press the battery re lease p lunger and ho ld while rotating the battery counterclockwise until it stops (battery base will be perpendicular to device hand le).
2. Grip the battery base and pull battery from battery chamber.
CHARGING THE BATTERY:
Important Note: The backup battery must charge at a low current. Initial charge-time for the backup
battery, therefore, is 72-hours. During this period, even though the main battery may indicate full charge,
the device cannot maintain any user data if the main battery is removed. The initial 72-hour charge-time for
the backup battery is required prior to first use or after a full drain of the backup battery.
Full drain of the backup battery will occur when:
▪ The main battery is removed and the device uses the backup battery to sustain its last state of operation for
15 minutes or more.
▪ The main battery’s charge drops below 7% (the backup battery will support continued function for up to 15
minutes).
Janam Technologies LLC
2-4
XG100WM User Manual
To charge the battery using the USB or Serial Cable:
1. Connect the power supply to the USB or serial cable.
2. Connect snap-on end of USB or serial cable to syncing/charging connector at the bottom of device,
making sure the JANAM logo on the connector faces up.
3. Insert appropriate AC adapter and plug in the power supply. Use only easily accessible wall outlets that
are easily reached with the length of supplied power cable.
To charge the battery using the Single-Slot or Four-Slot Cradle:
1. Connect the power supply to the cradle.
2. Connect the line cord to the power supply.
3. Insert appropriate AC adapter and plug in the power supply. Use only easily accessible wall outlets that
are easily reached with the length of supplied power cable.
4. Place the device in cradle. The LED will illuminate to confirm connection (orange indicates charging, green
indicates fully charged and red indicates fault).
5. The battery is fully charged in approximately 5 hours.
6. For Single-Slot cradle only: Charge a spare battery by placing the battery in the spare battery well with
connectors lined up. An LED will illuminate to confirm connection.
Charging a Spare Battery in Single-Slot Cradle Spare Battery Well or Four-Slot
Battery Charger
1. Insert and slide the battery into the charging slot as shown.
2. Press down and forward with index finger to fully seat the battery.
3. The LED will illuminate to confirm connection (orange indicates charging, green indicates fully charged
and red indicates fault).
4. The battery is fully charged in approximately 5 hours.
Turn the XG100WM on
After batteries have been charged for required length of time, press the red
power button located on the keypad to the right of the up/down/left/right
arrow keys.
The first time the device is turned on, calibrate the screen using the stylus.
To calibrate, simply follow the on-screen instructions and remember to save
your settings.
Note:
If your XG100WM came pre-loaded with a custo m soft ware app licatio n, a
welcome utility may not appear. If this hap pe ns, follow the on-sc reen
instructions.
Janam Technologies LLC
2-5
Understanding the Desktop
Command bar
Your XG100WM mobile computer desktop has following features.
What do the Status Icons Mean?
XG100WM User Manual
Janam Technologies LLC
2-6
XG100WM User Manual
3
Set up your Janam XG100WM
Locate Front Panel Controls
1. Power button - Pressing the power button turns the handheld computer on (if it is off) and
returns to the last screen that was displayed. Press the power button to turn the handheld
computer off.
2. Use the backlight to illuminate the screen in low-light conditions.
For 52-Keypad: Press Orange (Function) key and then press “Z” key to turn display backlight
on/off.
For 42-Keypad: Press Orange (Function) key and then press “N” key to turn display backlight
on/off.
3. Use the keylight to illuminate the keypad.
For 52-Keypad: Press Orange (Function) key and then press “X” key to turn keylight on/off.
For 42-Keypad: Press Orange (Function) key and then press “M” key to turn keylight on/off.
4. Janam XG100WM LCD displays the applications and data stored in your handheld computer. It
is touch-sensitive.
Locate Back Panel Components
1. microSD Card Slot (located under microSD card cover) - Remove 2 screws using cross
head screwdriver. Remove the cover and insert a microSD card into the slot. Replace card slot
cover.
2. USB/serial connector - Connects your handheld computer to a PC via a sync/charging USB
cable or by inserting XG100WM into a Janam cradle.
IMPORTANT NOTE!
Always use the stylus for tapping or making strokes on the handheld computer screen.
DO NOT use a pen, pencil or any other object on the touch screen of the XG100WM.
Recalibrate the Screen
The first time you start the Janam XG100WM handheld computer, setup instructions will appear on
screen. These instructions include a calibration screen, or digitizer. Calibration aligns the internal
circuitry of the handheld computer with its touch-sensitive screen so the handheld can detect tapping
selected elements on the screen. You can also recalibrate your screen at any time.
To recalibrate your screen:
1. Tap the Start menu >
Settings > System Tab >
Screen.
2. Select Align Screen button,
and follow the on-screen
instructions, tapping the
screen where indicated.
Janam Technologies LLC
3-1
XG100WM User Manual
Customize the Today Screen
The Today screen can be customized by tapping Start menu >
Settings > Today.
To choose a background/theme:
On the Appearance tab, select the desired theme for the background.
To choose add a custom background image:
1. Select the use this picture as the background check
box, and tap Browse button to view a list of your picture
files.
2. Select the folder that contains the picture you want to use.
3. Select the file type of the picture.
4. Tap the file name of the picture you want to use.
5. Tap OK.
IMPORTANT NOTE!
Pictures can affect the readability of text on the Today screen
.
Janam Technologies LLC
3-2
XG100WM User Manual
To select/change the order of appearance:
1. On the items tab, select the items you want to appear on the
today screen.
2. Change the order by tapping the item and then tap move up or
move down.
Change Language and Regional Settings
Your Janam XG100WM ships with pre-set regional, language and input
settings. To change these settings, follow the directions below.
The style in which numbers, currency, dates and times are displayed is
specified in regional settings. To change these:
1. Tap Start menu > Settings > System tab > Regional Settings.
2. On the Region tab, select your Region and Language.
3. Do one of the following:
• On the Time tab, select the time display options you
want.
• On the Date tab, select the date display options your
want.
4. To customize settings further, tap the appropriate tabs and select
the desired options.
Janam Technologies LLC
3-3
Change the Date and Time Display
To set the time and date:
1. Tap Start menu> Settings > System tab > Clock &
Alarms.
2. Select the correct Time Zone, and change the Date or
Time.
3. Choose Alarms tab to set regular reminders.
4. Choose More tab to add/remove the clock on the title
bar in all programs and the sound alarm even when the
device is set to silent or vibrate.
Note: During synchronization, the time on your device is
updated with the time on your PC.
To set the time and date for a different location:
1. Tap Start menu > Settings > System tab > Clock & Alarms.
2. Tap Visiting.
3. Select the correct time zone, and change the time or date.
XG100WM User Manual
Janam Technologies LLC
3-4
XG100WM User Manual
Owner Identification and Password Protection
1. Tap Start menu > Settings > Personal tab > Owner
Information.
2. On the identification tab, enter your personal information.
To display owner information on the today screen:
1. Tap Start menu > Settings > Personal tab > Owner Information.
2. On the Options tab, select the identification information check box.
3. On the Options options tab, select the notes check box if you want additional text
displayed, such as: Reward if found.
4. On the Notes tab, enter the additional text.
Janam Technologies LLC
3-5
XG100WM User Manual
To protect your device with a password:
1. Tap Start menu > Settings > Personal tab > Lock.
2. Select the Prompt if device unused for check box, and select
the option from the dropdown menu.
3. In the password type box, select the type of password you
would like to use – Simple PIN or Strong alphanumeric. Enter
the password and key in the same password to confirm the
password.
4. On the Hint tab, enter a phrase to help you remember your
password. The hint displays after the wrong password is entered
four times.
5. Tap OK. You will be prompted to enter your password the next
time you turn on your Janam XG100WM.
IMPORTANT NOTE!
Each time a wrong password is entered, the time the device takes to respond will get longer and
longer until the device appears to be not responding. If you forget your password, you must reset
your device.
To change your password:
1. Tap Start menu > Settings >
Personal tab > Lock. Enter your
current password.
2. In the password box, enter your
new password.
3. On the Hint tab, enter a phrase to
help you remember your new
password. The hint displays after the
wrong password is entered four
times.
4. Tap OK.
Backlight and Brightness Preferences
To change backlight preferences:
1. Tap Start menu > Settings > System tab > Backlight.
2. Select Battery Power tab and make your changes in:
• Turn off backlight if device not used for
• Turn on backlight when a button is pressed or the screen
is tapped.
3. Select External Power, and make your changes in:
• Turn off backlight if device not used for
• Turn on backlight when a button is pressed or the screen
is tapped.
4. Click OK.
Janam Technologies LLC
3-6
Battery Power
To make the battery last longer:
1. Tap Start menu > Settings > System tab > Power.
2. On the Advanced tab, specify when your device turns off to
conserve battery power. For optimum conservation, specify 3
minutes or less. Default value is 1 minute.
3. Use the AC adapter to plug your device into external power
whenever possible.
4. Adjust the backlight settings using keypad.
To check the main battery and
backup battery status:
1. Tap Start menu > Settings >
System tab > Power.
2. On the Battery tab, Main Battery
status and Backup Battery status are
shown in bar chart from 0% to
100%.
3. Battery status can also be found in
Start menu > Settings > System
tab > XG100 Panel > Battery tab.
XG100WM User Manual
Button Assignment and Scrolling Speed
To program buttons:
1. Tap Start menu > Settings > Personal tab > Buttons >
Program Buttons tab.
2. First, select a button from the list, then assign a program
from the dropdown menu to that button.
Janam Technologies LLC
3-7
To adjust the speed for scrolling:
1. Tap Start menu > Settings >
Personal tab > Buttons >
Up/Down Control tab.
2. Do one of the following:
• Under delay before first
repeat, move the slider to
shorten or lengthen the
time that elapses before
scrolling begins.
• To change the time it takes
to scroll from one item to
the next, under repeat
rate, move the slider to
adjust the speed.
Volume Control
1. Tap the on the top command bar.
2. Move the indicator up or down to adjust volume.
3. Click off to turn volume off completely.
4. Click on the handheld’s background to close the popup.
5. Alternatively, user can use keypad to adjust the volume. On 52-
key keypad, <Func + H> keys for volume up and <Func + M>
keys for volume down.
XG100WM User Manual
Enable Sounds and Notifications
1. Tap Start menu > Settings > Personal tab > Sounds & Notifications > Sounds tab.
2. Tap or select the events and programs to enable sounds.
3. Select the Notifications tab to assign notifications to specific events.
4. Select the Event in the dropdown menu, tap Play sound checkbox and choose sound.
5. Click ok.
Janam Technologies LLC
3-8
Loading...