James Martin 908M29PNK User Manual

J A M E S M A R T I N V A N I T I E S
908-M29-PNK LEVITATE MIRROR
LED Mirror - Installation Instructions
James Martin Vanities always recommends you hire or consult a professional contractor when installing our products
Note: This mirror is not intended for outdoor use
IMPORTANT: Please read all instructions prior to beginning the installation of this mirror
• Make sure the installation area is free of clutter.
• Turn off electricity including wall switch's.
• Always use two or more person when hanging mirrors
Parts included
CA
Wire Nuts X 4pcs
( 10*45)
Screws X 4pcs
( 5*40 )
B
Mounting Bracket X 1pc
FEATURES
• 5mm copper free silver mirror
• High output LED light:1800-1900LM,4000K CCT,IP66
• Touch switch for surface LED
CODES / CERTIFICATIONS
Mirror
Electrical Cord (attached to back of mirror)
UL 2108
UL 8750
U
L
R
Mirror Weight: 44Ibs(20kgs)
908-M29-PNK LEVITATE MIRROR
Mirror Weight: 44Ibs(20kg)
Pre-Installation Notes
• 120 Vac 60Hz wall outlet location - Required for source power
• Mirror hangs in Portrait orientation
• Includes hardware with easy installation via Plug and Hang Systen
cooling vents
29”[737mm]
27 5/8”[703mm]
2 1/4”[57mm]
2”[50mm]
Open area in back cover for electrical cord storage
7 7/8”
[200mm]
9 7/8”[250mm]
7 7/8”[200mm]
Back view
8 3/4”
[222mm]
29 3/4”
[755mm]
X3 magnification
Touch the Sensor switch
Front view
40 5/8”
[1033mm]
42”
[1067mm]
Side view
908-M29-PNK LEVITATE MIRROR
Tools required
Screw driver Drill with 3/8" bit Pencil levelMeasuring Tape Screw driver The hammer
Mirror Weight: 22Ibs(10kgs)
Measure the distance between the bottom
1 2 3
of the mirror and point a.
a
Draw a horizontal line from the point a using a level Draw the points according to the hole
a
BACK OF THE MIRROR
b
A
Attach the mounting braket to the wall. Hang the mirror on the mounting bracket
Drill the holes on the wall and insert
4 5 6
the nuts into the holes.
C
of the mounting bracket
WALL
B
MIRROR
BRACKET
NOTE: Always use two or more
people when hanging mirrors
908-M29-PNK LEVITATE MIRROR
CAUTIONS
DANGER:
breaker or fuse box before attempting any installation procedure.
DANGER:
Observe all local electrical codes and building codes. Wire the mirror in accordance with the electrical codes.
Grounding instructions:
For a grounded, cord-connected product rated max 15 amperes and intended for use on a nominal 12-volt supply circut: This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in sketch A (below). Make sure that the product is connected to an outlet having the same configuration as the plug.
No adapter should be used with this product as illustrated in sketch B and C.
A B C
Risk of personal injury. To avoid possible electrical shock, the electricity must be turned off at the circuit
Risk of personal injury. To avoid possible electrical shock, the mirror must be properly grounded.
Grounded outlet
Adapter
Adapter
Grounded pin
Grounded outlet box
Grounded outlet box
Metal screw
Tab for
grounding screw
908-M29-PNK LEVITATE MIRROR
Care and Cleaning Instructions for Mirrors
CLEANER
• The best and safest cleaner for a mirror is clean, warm water used with a soft cloth. Be careful not to allow
the edges of the mirror to get or remain wet over a period of time. If using a commercial glass or mirror cleaner, be sure to use a standard brand of mirror cleaner that does not contain ammonia or vinegar.
APPLICATION
Never spray any cleaner directly on to a mirror. Instead apply the cleaner to a soft cloth and then wipe the mirror.
CLOTHS
Always use soft, grit-free cloths when cleaning a mirror to reduce chances of scratching the surface.
• FINISH
Be sure to dry all joints and edges thoroughly to be certain no commercial cleaner comes in contact
with the edge and backing.
Loading...