J A M E S M A R T I N V A N I T I E S
880-M28-BKO CRAWFORD MIRROR
LED Mirror - Installation Instructions
James Martin Vanities always recommends you hire or consult a professional contractor when installing our products
Note: This mirror is not intended for outdoor use
IMPORTANT: Please read all instructions prior to beginning the installation of this mirror
• Make sure the installation area is free of clutter.
• Turn off electricity including wall switch's.
• Do not modify wires in anyway
• Always use two or more person when hanging mirrors
Parts included
CA
Wire Nuts X 4pcs
( 10*45)
B
Mounting Bracket X 1pc
Screws X 4pcs
( 5*40 )
FEATURES
• 5mm copper free silver mirror
• High output LED light:1800-1900LM,4000K CCT,IP66
• Touch switch for surface LED
Mirror
Electrical Cord
(attached to back of mirror)
CODES / CERTIFICATIONS
•
UL 2108
UL 8750
•
U
L
R
880-M28-BKO CRAWFORD MIRROR
Mirror Weight: 29.7Ibs(13.5kgs)
Pre-Installation Notes
• 120 Vac 60Hz wall outlet location - Required for source power
• Mirror hangs in Portrait orientation
• Includes hardware with easy installation via Plug and Hang Systen
3”[77mm]
cooling vents
5 7/8”
[150mm]
5 7/8”[150mm]
[257mm]
5 7/8”
[150mm]
10 1/8”
25 1/2”
[647mm]
27”[685mm]
24 1/2”[621mm]
2 3/4”[70mm]
47 1/4”
[1200mm]
29 5/8”
[753mm]
Open area in back cover
for electrical cord storage
Back view Front view Side view
Touch the Sensor switch
880-M28-BKO CRAWFORD MIRROR
Tools required
Screw driver Drill with 3/8" bit Pencil levelMeasuring Tape Screw driver The hammer
Mirror Weight: 29.7Ibs(13.5kgs)
Measure the distance between the bottom
1 2 3
of the mirror and point a.
a
Draw a horizontal line from the point a using a level Draw the points according to the hole
BACK
OF THE
MIRROR
Center line
Drill the holes on the wall and insert
4 5 6
the nuts into the holes.
A
b
Attach the mounting braket to the wall. Hang the mirror on the mounting bracket
a
C
of the mounting bracket
WALL
B
MIRROR
BRACKET
NOTE: Always use two or more
people when hanging mirrors
880-M28-BKO CRAWFORD MIRROR
CAUTIONS
DANGER: Risk of personal injury. To avoid possible electrical shock, the electricity must be turned off at the circuit
breaker or fuse box before attempting any installation procedure.
DANGER: Risk of personal injury. To avoid possible electrical shock, the mirror must be properly grounded.
Observe all local electrical codes and building codes. Wire the mirror in accordance with the electrical codes.
Grounding instructions:
For a grounded, cord-connected product rated max 15 amperes and intended for use on a nominal 12-volt supply circut:
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in sketch A (below).
Make sure that the product is connected to an outlet having the same configuration as the plug.
No adapter should be used with this product as illustrated in sketch B and C.
A B C
Grounded pin
Grounded outlet
Grounded
outlet box
Adapter
Metal screw
Grounded
outlet box
Adapter
Tab for
grounding screw
880-M28-BKO CRAWFORD MIRROR
• Care and Cleaning Instructions for Mirrors
• CLEANER
The best and safest cleaner for a mirror is clean, warm water used with a soft cloth. Be careful not to allow
the edges of the mirror to get or remain wet over a period of time. If using a commercial glass or mirror
cleaner, be sure to use a standard brand of mirror cleaner that does not contain ammonia or vinegar.
APPLICATION
•
Never spray any cleaner directly on to a mirror. Instead apply the cleaner to a soft cloth and then wipe the
mirror.
CLOTHS
•
Always use soft, grit-free cloths when cleaning a mirror to reduce chances of scratching the surface.
• FINISH
Be sure to dry all joints and edges thoroughly to be certain no commercial cleaner comes in contact
with the edge and backing.
Loading...