JAMEASY BPVN01 User Manual

Jameasy Plus

violin

User Guide BPVN01

Thank you for purchasing the Jameasy
Plus. Please read this user guide
before using the device. If this product
will be used by young children, this
manual should be read and explained
to them by an adult.

※ Please read the manual for the
Jameasy application.
(http://jameasy.com ‒ Product ‒ User
manual)

Copyright ⓒ 2015 Jameasy Inc. All rights reserved

Components

This package includes a Jameasy
device and an user guide. The device
contains a non-rechargeable button­type battery (CR2032) already installed.

Power

Battery
cover

Rubber
buffer

※ To turn on the device, press and hold
the power button until 'beep-' sound
and the LED lights up.

button

LED
Status

Clip

Getting Started

1. Search Jameasy app on Google
Play or App Store and download the
app on your smartphone or tablet.

For more information about the
Jameasy app and supported smart
phone models, visit our website at
‘http://jameasy.com’
※ Before following these steps, check
whether data connection is available
and Bluetooth is allowed of your
smartphone.

2. Remove the plastic
insulation tab from your
device and turn it on.

※ The new product
includes a plastic tab to
prevent a battery from
discharging.

3. Connect the device
with your smartphone.

Run the app and go to
device setting screen in
the app. When the device
list is displayed, tap
‘connect’ button.
The Status LED will softly blink yellow
when the device is successfully connect­ed.

Clip the device onto a violin

A scroll of a violin is the recommended
place without corrupting the original
sound of a violin.
To prevent your violin from any physical
damage, please remove the device
after use.

<clip example>

WARNING : CHOKING HAZARD

- Small parts

Not for children under 3 years.

Battery Replacement

When the LED turns red, the battery
(CR2032) should be replaced. Press
the middle part of the device, and slide
and remove the battery cover located
on the head of the device as shown in
illustration below. After removing the
old battery, insert the new battery with
the positive side (+) facing upward.

Power OFF / Sleep Mode

To turn off the device, press the power
button until ‘beep’ sounds. The device
will be turned off automatically when
the device is left without connecting to
the application more than one minute,
or not used more than 10 minutes.

Status LED

Colors and blink period of LED show
the status of the device described as
below.

LED Status

LED off Power off

Yellow, Short blink

Yellow, Soft blink

Yellow, Solid LED

Red

Instructions

Power on, Paring off

Power on, Paring on

Power on, Practice mode

Have to replace battery

Specifications

Jameasy Plus violin

Name

Model Num

Detection

Detection

accuracy

Wireless

technology

Wireless

Environment

Dimension

(W x D x H)

Battery life

BPVN01

B1(41.20 Hz) ‒ B6(1975.54Hz)

range

Better than ± 1cent

Bluetooth v4.2

Approx. 32’(5m), actual range
depends on the surrounding

range

environment.

Power

CR2032(3V DC) Lithium Battery

supply

(non-rechargeable)

Temp. 14℉~104℉(-10℃ ~ 40℃)
Humidity 0 ~ 85%

0.87” x 1.73” x 1.57” /
22 x 44 x 40 mm

0.53 oz/15g(including batteries)

Weight

Approx. 24hours (A4 continuous
input, Bluetooth connected)

Troubleshooting

• LED does not light up

- Make sure the battery is installed
correctly. (→ See Battery Replacement
instructions).

- Try removing the battery and then
re-installing it.

- Try replacing the battery.

• LED does not light off.

- Try removing the battery and then
re-installing it.

• Cannot connect to smart device
(Jameasy application)

- Please check whether there is a
wireless AP or microwave oven near.

• No response when you play the
violin.

- Please check whether the device has
been disconnected from the applica­tion on your mobile device.

- Make sure that the device is attached
well to your violin.

WARNING - BATTERY LEAKAGE

Perchlorate material

- special handling may apply.

More information can be found at
http://www.dtsc.ca.gov/Hazard­ousWaste/Perchlorate/index.cfm
Leakage of battery fluid can cause
personal injury as well as damage to
your accessory. If battery leakage
occurs, thoroughly wash the affected
skin and clothes. Keep battery fluid
away from your eyes and mouth.
Leaking batteries may make popping
sounds.

To avoid battery leakage :

• Do not use any battery other than the
type specified for this product (CR2032).

• Do not attempt to recharge the battery.

• Do not put the battery in backwards.
The positive side (+) should face
outwards when inserted correctly.

• Do not leave the battery in the access­ory for long periods of non-use.

• Do not use damaged, deformed, or
leaking battery.

• Do not dispose of the battery in a fire.

• Do not short-circuit the battery or the
terminals in the battery compartment.

• Do not attempt to disassemble the
battery.

• Do not expose the battery to extremes
of heat or to liquids.

• When the battery has no charge left,
remove it from the accessory and
dispose of properly, following appropri­ate local guidelines and regulations. To
find a battery collection site near you,
please contact your local solid authority
or visit : http://www.call2recycle.org/

If you cannot resolve the problem with
solutions stated above, please contact
us. [e-mail]

THE FCC REGULATION WARN­ING (for USA)

NOTE : This equipment has been
tested and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interfer­ence to radio or television reception,
which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interfer­ence by one or more of the following
measures :

• Reorient or relocate the receiving
antenna.

• Increase the separation between the
equipment and receiver.

※ Specifications and appearance are
subject to change without notice for
improvement of product.

FCC ID : 2ALK7-BPVN01