JAI CV-S3300, CV-S3200 User Manual

DSP Color CCD Cameras

CV-S3200/3300

Operation Manual

(Rev.B)

CV-S3200/3300

DECLARATION OF CONFORMITY

AS DEFI NED BY THE COUNCIL DIRECTIVE

89/336/EEC

EMC (ELECTROMAG NETIC COMPATI BILITY)

WE HE R EWITH DECL AR E THAT THIS PRODUCT

COMPLIES WITH THE FOLLOWING PROVISIONS APPLYING TO IT.

EN-50081-1

EN-50082-1

2

Table of Contents

CV-S3200/3300

CE declaration...........................................................................................................

1. General..................................................................................................................

2. Main features........................................................................................................

3. Standard composition...........................................................................................

4. Pin assignment .....................................................................................................

5. Functions and operations .....................................................................................

5.1 SW1 switch on PK8167 board......................................................................

5.2 On-screen-menu ........................................................................................

5.3 RS 232C functions......................................................................................

6. External appearance .............................................................................................

2

4

4

5

5

6
6
7

11

12

7. Specifications .......................................................................................................

8. Appendix ..............................................................................................................

8.1 Precautions ................................................................................................

8.2 Typical CCD Characteristics ........................................................................

8.3 References.................................................................................................

9. Users Record.........................................................................................................

13

14
14
14
14

15

3

CV-S3200/3300

1. General

The CV-S3200/3300 is a new high-resolution color camera series, available in PAL or NTSC
format. The camera series was developed with JAI's new DSP processor, which has remarkable
high signal to noise ratio as well as a high bit flow. The cameras also have built-in RAM, which
together with the DSP enables the camera to produce field integration with 100% horizontal
resolution.

The CV-S3200/3300 series features EXview HAD
1/3")which are extra light sensitive and have enhanced anti-smear and blooming characteristics.

The cameras run on 12V DC and can be gen-locked or use VBS for external synchronization.
There are connections for video control or direct drive lens, and VBS and Y/C video outputs.
Both cameras have CS/C-mount with a variable mounting ring for back focus. The CV-S3300
has screw terminals for power, gen-lock and line-lock. The CV-S3200 comes with D-sub
connector.

The camera set-up can be performed via the JAI software platform and an RS232C port, or from
a new on-screen menu that can be controlled by the three buttons mounted on the rear of the
camera. Both the software and the on-screen-menu can control the following setting:shutter,
integration, gamma, AGC,H/V enhancer, iris-level for direct drive, positive/negative picture,
back-light compensation, and AWB fixed or manual color temperature.

Applications include surveillance, security, medical and a large variety of other industrial
applications.

TM

sensors (CV-S3200:1/2" and CV-S3300:

2. Main Features

1/2" EXview HADTM IT color CCD sensor for CV-S3200,
1/3" EXview HAD

TM

IT color CCD sensor for CV-S3300

NTSC : 768 (h) x 494 (v) , PAL : 752 (h) x 582 (v)
450 TV lines horizontal resolution
Composite VBS and Y/C output
Excellent color reproduction
Field integration mode for higher sensitivity
S/N ratio > 50 dB
White balance automatic or manual
Auto iris and CCD iris for light regulation
Manual shutter up to 1/10,000 sec.
Scanning reversal function (mirror-effect mode)
CS-lens mount with focus adjustment
CV-S3200 employs 9 pin Dsub connector at camera rear panel for single cable solution.
CV-S3300 provides 7 pin terminal at camera rear panel for easy cable installation.

4

3. Standard compositions

1)

Camera main body

2)

C-mount adaptor (MP-55)

3)

Auto iris lens pulg (E4-191J-100)

4)

Y/C out plug (TCP8040-01-520)

5)

Operation manual

4. Pin assignment

4-1. DC IN/SYNC/RS-232C connector

CV-S3200/3300

x 1
x 1
x 1
x 1
x 1

a) 9 pin D-sub connector for CV-S3200

4-40
UNC Thread

b) 7 pin terminal for CV-S3300

1

:

Ground

2

:

+12V DC input

3

:

Ground

4

:

VBS output

5

:

Sync input

6

:

Y output

7

:

C output

8

:

TXD output

9

:

RXD input

1

:

RXD input

2

:

TXD output

3

:

Ground

4

:

Sync. input

5

:

Ground

6

:

+12V DC input

7

:

Ground

5

4-2. S-VIDEO connector

4-3. LENS connector

CV-S3200/3300

1

:

Ground

2

:

Ground

3

:

Y output

4

:

C output

1

:

+9V / Damp-

2

:

NC / Damp+

3

:

Iris / Drive+

4

:

Ground / Drive-

5. Functions and operations

5-1. SW1 switch on PK8167 board

This switch is to select the type of auto iris. It is located on the CCD board (PK8167), as below.

Up
Down::

Direct drive mode (Passive)
Video controlled (Active)

Note : Factory pre-set is Video controlled.

SW1 switch

6

CV-S3200/3300

5-2. On-screen-menu

On-screen-menu can be controlled by the “UP”, “DOWN” and “FUNC” switches on the rear panel.

5-2-1. Functions

The following functions are adjustable at on-screen-menu.

White balance
Shutter
Gain
Back light compensation
Lens iris
Gamma
Scanning reversal
Sensitive (Field integration)

a) White balance
This function is to adjust the color temperature to make the color of the image correct.

3200 K
4600 K
5600 K
Auto

Manual
One push

For incandescent lamp or halogen lamp.

:

For white fluorescent lamp.

:

For daylight.

:

The TTL system is employed for auto white balance, and it detects the

:

highest video level in objects to recognize a white color.
It is necessary to place the camera in a position where the camera does
not pick up spot lights and fluorescentlights.

To adjust the color temperature between 2700 K to 6700 K.

:

Refer to 5-2-2 (d).

:

Note : Factory pre-set is auto white balance.

7

CV-S3200/3300

b) Shutter
This function is used for “freezing” objects and for light regulations. Nine exposure time settings are
available.

OFF
Selectable shutter
Flicker-less
CCD iris

1/60 sec. (NTSC), 1/50 sec. (PA L)

:

1/125, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10,000 sec.

:

1/100 sec. (NTSC), 1/120 sec. (PA L)

:

Shutter speed changes automatically.

:

(1/60 sec. to 1/10000 sec. (NTSC), 1/50 sec. to 1/10,000 sec.(PAL))

Note : Factory pre-set is OFF.

CAUTION

Under certain unique light conditions, the following may appear.

1.

- Strong smear and/or blooming on highlighted objects.

- Noticeable flicker in the picture.

CCD iris

2.
Continuous variable electronic shutter controls the exposure time of the CCD sensor, depending on the incoming

light level. When this mode is selected, auto or manual iris lens can be used instead of an auto iris lens.

3.

Shutter speed and sensitive mode
In sensitive made the CCD iris does not function.

c) AGC (Auto gain control)
OFF

+12 dB
+24 dB
Manual

:

Gain is fixed at minimum 0 dB

:

AGC ON (0 to +12 dB)

:

AGC ON (0 to +24 dB)

:

Manual gain

Note : Factory pre-set is AGC OFF.

CAUTION

1. Auto iris lens can be used only when the CCD iris is OFF.

8

CV-S3200/3300

d) BLC (Back Light Compensation)
BLC circuit will c0mpensate for extreme highlights in the field of view.

There are three pre-defined patterns that can be selected. These are shown below. The higher
the value, the more backlight compensation.

Patten 1

Patten 2

Patten 3

1 1 0 0 0 0

4 9 4 0 15 0 0 10 0

1 1 0 0 4 4

Note : Factory pre-set is OFF.

CAUTION

The BLC works under the follwing conditions:

1.

BLC
AGC ON ON OFF OFF
CCD iris ON OFF ON OFF

It is recommended to switch “BLC OFF” when using the camera with pan/tilt head or if the scene illumination

2.
changes rapidly.

: Effective
: Not-effective

3.

With “BLC ON” the regulation speed of the iris is decreased.

e) Iris level
This is to set the video level, when the camera is set at CCD iris, AGC ON and auto iris.

9

CV-S3200/3300

f) Gamma
This function is to set the gamma correction.

0.45

0.6

1.0

Correction

:

Correction

:

Linear

:

Note : Factory pre-set is 0.45.
g) Scanning reversal (mirror-effect mode)

This function can change the horizontal scanning between normal and reverse.
OFF

ON

Normal scanning

:

Reversal scanning

:

Note : Factory pre-set is set at OFF.
h) Field integration

The sensitivity can be set at these pre-set positions.
OFF
2F
4F
8F
16F
32F
64F

:

Standard sensitivity (Exposure time = 1 field)

:

2 times higher than standard sensitivity (Exposure time = 2 fields)

:

4 times higher than standard sensitivity (Exposure time = 4 fields)

:

8 times higher than standard sensitivity (Exposure time = 8 fields)

:

16 times higher than standard sensitivity (Exposure time = 16 fields)

:

32 times higher than standard sensitivity (Exposure time = 32 fields)

:

64 times higher than standard sensitivity (Exposure time =64 fields)

Note : Factory pre-set is OFF.

5-2-2. Operations

Screen display (example)

White balance Manual

Red Blue

Function buttons for on-screen-menu

Up switch
Function switch

Down switch

Rear panel of CV-S3300 (example)

Note : This scroll bar will be displayed when the following
functions are selected.
White balance = manual, AGC = manual, Iris = manual

10

CV-S3200/3300

(a)

(b)

(c)

(d)

To start adjustment, push the “FU NC” button. The menu will appear on the monitor .
(See page 12)

Use “UP” or “DOWN” buttons to choose functions. To select function, press the “FUNC”
button.

After selecting the function, press “UP” or “DOWN” buttons to choose mode. To select
mode, press the “FUNC” button.

To use One Push White Balance.
Go to the next function if needed, and repeat (b) to (c).

1. Change to White Balance mode by Function SW.

2. Change to One-push mode by Up or Down SW.

3. Push Function SW and make it READY.

4. Push Up SW, and One-Push White Balance function starts.

5. Push Function SW to save the data (R.B.Gain) of One-Push White Balance.
If you turn off the power without saving the data, it will return to the original status.

5-3. RS 232C functions

White balance

a)

Electronic shutter

b)

Auto gain control

c)

Back light compensation

d)

Iris level

e)

Gamma

f)

Scanning reversal

g)

Frame integration

h)

:

To adjust the color temperature

:

To adjust the shutter speed

:

OFF, +12dB, +24dB, manual selectable

:

To create your own BLC pattern.

:

To adjust the video level

:

0.45, 0.60, 1.0 selectable

:

To select the scanning direction

:

To select the sensivity

11

6. External appearance

e.g. CV-S3200

CV-S3200/3300

Unit : mm (inches)

e.g. CV-S3300

4-40 UNC Thread

12

7. S7. S

pecificationspecifications

7. S

pecifications

7. S7. S

pecificationspecifications

CV-S3200/3300

Model name
TV standard

Scanning system

CCD sensor

Effective pixels

Cell size

Resolution (horizontal)
Sensitivity
S/N ratio

Video output

Gain
White balance
Gamma
Synchronization

CV-S3200 CV-S3300

NTSC / PAL NTSC / PAL

NTSC : 525 lines, 30 frames/sec.

PAL : 625 lines, 25 frames/sec.

Color 1/2" IT CCD sensor Color 1/3" IT CCD sensor

NTSC : 768 (h) x 494 (v)

PAL : 752 (h) x 582 (v)

NTSC : 8.4 (h) x 9.8 (v)µm

PAL : 8.6 (h) x 8.3 (v)µm

0.4 lux on sensor (AGC ON, 50% video)

>

50 dB (AGC OFF, Gamma=1.0)

VBS 1.0 Vpp at 75 Ohm

Y/C output 1.0 Vpp at 75 Ohm

Off, +12 dB, +24 dB, manual

3200K, 4600K, 5600K, auto, manual,one push

Internal / external sync. or VBS 1.0 Vpp

450 TV line

1.0 - 0.6 - 0.45

NTSC : 6.35 (h) x 7.4 (v)µm

PAL : 6.3 (h) x 6.25 (v)µm

Shutter

Field integration
Back light compensation
Scanning reversal
Serial interface

Rs 232C functions

Operating environment

Power
Lens mount
Dimensions
Weight

Note : Above specifications are subject to change without notice.

OFF (1/60 at NTSC, 1/50 at PAL), 1/125, 1/250, 1/500, 1/1000, 1/2000,

1/4000, 1/10,000, CCD iris, Flicker-less (NTSC : 1/100, PAL : 1/120)

Off, 2F 64F

Off, pattern 1, pattern 2, pattern 3

Off, On

RS 232C

Electronic shutter, CCD iris, Flicker-less, White balance,

Back light compensation, Video reversal, Gamma, Gain, Chroma

Temperature : -5°C to + 45°C

Humidity : 20% to 80% non-condensing

+12 VDC ± 10%, 3.0W

CS-mount

45 x 55 x 110.2 (HxWxD) mm

350 g approx.

13

CV-S3200/3300

8. Appendix

8-1 Precautions

Personnel not trained in dealing with similar electronic devices should not service this camera.
The camera contains components sensitive to electrostatic discharge. The handling of these devices

should follow the requirements of electrostatic sensitive components.
Do not attempt to disassemble this camera.
Do not expose this camera to rain or moisture.
Do not face this camera towards the sun, extreme bright light or light reflecting objects.

When this camera is not in use, put the supplied lens cap on the lens mount.
Handle this camera with the maximum care.

Operate this camera only from the type of power source indicated on the camera.
Power off the camera during any modification such as changes of jumper and switch setting.

8.2 Typical CCD Characteristics

The following effects may be observed on the video monitor screen. They do not indicate any fault of the
CCD camera, but do associate with typical CCD characteristics.

V. Smear

Due to an excessive bright object such as electric lighting, sun or strong reflection, vertical smear may be
visible on the video monitor screen. This phenomenon is related to the characteristics of the Interline
Transfer System employed in the CCD.

V. Aliasing

When the CCD camera captures stripes, straight lines or similar sharp patterns, jagged image on the
monitor may appear.

Blemishes

Some pixel defects can occur, but this does not have en effect on the practical operation.

Patterned Noise

When the CCD camera captures a dark object at high temperature or is used for long time integration,
fixed pattern noise (shown as white dots) may appear on the video monitor screen.

8.3 References

1. This manual and datasheet for CV-S3200/3300 can be downloaded from www.jai.com

2. Camera control software can be downloaded from www.jai.com

14

9. User’s Record

Camera type: CV-S3200/3300

Revision: (Revision B)

Serial No. .................

Users Mode Settings

Users Modifications

CV-S3200/3300

15

2700-21107 E B1 0701

JAI A·S, Denmark

Produktionsvej 1, 2600 Glostrup
Copenhagen, Denmark
Phone [phone]
Fax [phone]
www.jai.com

JAI Corporation, Japan

German Industry Center
1-18-2 Hakusan, Midori-ku
Yokohama,
Kanagawa 226-0006, Japan
Phone [phone]
Fax [phone]
www.jai-corp.co.jp

JAI America, Inc., USA

Suite 450
23046 Avenida de la Carlota
Laguna Hills, CA 92653
USA
Phone [phone]
Fax [phone]
www.jai.com