JAI CV-A10CL-A70CL Operation Manual

1019E-1007

CV-S3500E

NTSC/PAL selectable

Progressive scan color video camera

Document Version: Ver.1.0

CV-S3500E_Ver.1.0_Sept2010

User's Manual

CV-S3500E

- 2 -

Notice

The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan
and may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the
use of its product and assumes no responsibility for any errors which may appear or for damages
resulting from the use of the information contained herein. JAI Ltd., Japan reserves the right to
make changes without notice.

Company and product names mentioned in this manual are trademarks or registered trademarks of
their respective owners.

Warranty

For information about the warranty, please contact your factory representative.

Certifications

CE compliance

As defined by the Directive 2004/108/EC of the European Parliament and of the Council, EMC
(Electromagnetic compatibility), JAI Ltd., Japan declares that CV-S3500E complies with the
following provisions applying to its standards.
EN 61000-6-3 (Generic emission standard part 1)
EN 61000-6-2 (immunity)

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.

Warning

Changes or modifications to this unit not expressly approved by the party responsible for FCC

complia nce could void the user’ s authorit y t o operate the equipment.

CV-S3500E

Supplement

The following statement is related to the regulation on “ Measures for the Administration
of the control of Pollution by Electronic Information Products “ , known as “ China RoHS “.
The table shows contained Hazardous Substances in this camera.

mark shows that the environment-friendly use period of contained Hazardous

Substances is 15 years.

功象嶄鯖繁酎慌才忽佚連恢匍何〆窮徨佚連恢瞳麟半陣崙砿尖一隈〇云恢瞳ゞ 嗤蕎嗤
墾麗嵎賜圷殆兆各式根楚燕 〃泌和

嶷勣廣吭並㍻

嗤蕎嗤墾麗嵎賜圷殆兆各式根楚燕



桟隠聞喘豚㍉

窮徨佚連恢瞳嶄根嗤議嗤蕎嗤墾麗嵎賜圷殆壓屎械聞喘議訳周和音氏窟伏翌
亶賜融延、窮徨佚連恢瞳喘薩聞喘乎窮徨佚連恢瞳音氏斤桟廠夛撹冢嶷麟半
賜斤児繁附、夏恢夛撹冢嶷鱒墾議豚㍉。

方忖仝15々葎豚㍉15定。

CV-S3500E

- 3 -

Table of Contents

1. General ............................................................................................................... - 5 -

2. Main Features ....................................................................................................... - 5 -

3. Composition ......................................................................................................... - 5 -

4. Locations ............................................................................................................ - 6 -

4.1. Locations and functions .................................................................................. - 6 -

4.2. LED indication .............................................................................................. - 7 -

4.2.1 Power indication ..................................................................................... - 7 -

4.2.2 LED (LINK) ............................................................................................ - 7 -

4.2.3 LED (ACT) ............................................................................................. - 7 -

5. Pin Assignment ...................................................................................................... - 8 -

5.1. D-SUB 9-pin multi-co n nect or (DC-in/Video/RS-232C) ................................................ - 8 -

5.2. RJ-45 Ethernet Connector ................................................................................. - 8 -

Note: When PoE is used, Cat5 or better cable should be used. .......................................... - 8 -

5.3. Auto iris lens connector ................................................................................... - 8 -

6. Connections ......................................................................................................... - 9 -

6.1. Power ........................................................................................................ - 9 -

6.2. Video output (NTSC or PAL) ............................................................................. - 9 -

6.3. Ethernet connection ...................................................................................... - 9 -

6.3.1 MAC address and IP address ....................................................................... - 9 -

6.3.2 Automatic acquisition of RTC time (SNTP) .................................................... - 10 -

6.3.3 User access ......................................................................................... - 10 -

6.3.4 Setup menu ......................................................................................... - 10 -

6.3.5 Image format through Ethernet interface .................................................... - 10 -

7. Camera configuration – OSD (On Screen Display) .......................................................... - 11 -

7.1. Top menu ................................................................................................. - 11 -

7.2. CAMERA menu tree ..................................................................................... - 13 -

7.3. SET UP menu tree ....................................................................................... - 14 -

7.4. Descriptions of camera functions ...................................................................... - 15 -

8. Camera Configuration – RS-232C .............................................................................. - 16 -

8.1. RS-232SC Interface ...................................................................................... - 16 -

8.2. Download and install CV-S3500E camera control tool ............................................ - 16 -

8.3. Camera control tool ..................................................................................... - 17 -

9. Camera configuration and how to use web browser ...................................................... - 21 -

9.1. Initial settings .............................................................................................. - 21 -

9.1.1 Set IP address manually .......................................................................... - 21 -

9.1.2 Obtain an IP address automatically. ........................................................... - 23 -

9.2. TOP menu .................................................................................................. - 23 -

9.3. View Camera top menu ................................................................................. - 24 -

9.4. SetUp top menu .......................................................................................... - 25 -

9.4.1 SetUp-D Zoom ...................................................................................... - 25 -

9.4.2 SetUp-Camera ...................................................................................... - 25 -

9.4.3 SetUp-capture ...................................................................................... - 26 -

9.4.4 SetUp-Network ..................................................................................... - 26 -

9.4.5 SetUp-Time ........................................................................................ - 27 -

9.4.6 SetUp - Reset ....................................................................................... - 27 -

9.4.7 SetUp-User .......................................................................................... - 28 -

10. External Appearance and Dimens io ns ..................................................................... - 29 -

11. Specifications .................................................................................................. - 30 -

11.1. Spectral sensitivity .................................................................................... - 30 -

11.2. Specifications table .................................................................................... - 31 -

Appendix .............................................................................................................. - 33 -

1. Precautions .................................................................................................. - 33 -

2. Typical Sensor Characteristics ........................................................................... - 33 -

3. Caution when mounting a lens on the camera ........................................................ - 33 -

4. Exportation .................................................................................................. - 33 -

CV-S3500E

- 4 -

5. References .................................................................................................. - 33 -

Change history ....................................................................................................... - 34 -

User's Record ......................................................................................................... - 35 -

CV-S3500E

- 5 -

1. General

The CV-S3500E is a high resolution camera employing 1/3 inch, 1.25-megapixel progressive scan
CCD.
The CV-S3500E has conventional analog video output, such as composite video and Y/C (luminance
and chrominance) signal. It also provides digital compressed video for both moving and still images.
JPEG still image, Motion JEPG, MPEG4 or H.264 is selectable for digital output. The digital data is
transferred through Ethernet, 100BASE-T or 10BASE-T networking. The power is also provided over
Ethernet (PoE).

The CV-S3500E utilizes a CS mount and includes a C-mount adaptor as an accessory for various C
mount lenses.
The CV-S3500E has an on-screen display for setup, as well as RS-232C control and controls
accessible through Ethernet.

The CV-S3500E is suitable for various applications using NTSC or PAL analog output or as an IP
network camera providing high quality images.

2. Main Features

• 1/3 inch progressive scan Bayer mosaic color CCD with 1.25 million effective pixels

• 1280 x960 ( 15 fps ) and 960 x 720 ( 30 fps ) sensor scanning modes

• Dual encoding for JPEG and MPEG4/H.264

• Motion JPEG, MPEG4 or H.264 with 640 x 480 resolution image through Ethernet

• NTSC or PAL output converted from 1280 x 960 resolution or 960 x 720 resolution

• Analog Composite and YC outputs for NTSC or PAL signal

• On-screen menu set up

• Auto iris connector built in (DC or video)

• Auto shutter function

• Gamma selection of 1.0, 0.6 or 0.45

• 2x digital zoom function

• Power over Ethernet or DC 10.8V to DC 26.4 through D-sub 9-pin connector

• RS-232C interface or Ethernet for camera settings

3. Composition

Camera main unit x 1

C Mount adapter x 1

Auto Iris Lens Plug (4pin) x 1
Hexagonal wrench x 1

CV-S3500E

- 6 -

4. Locations

4.1. Locations and functions

①

Lens mount

CS Mount (note1)

②

Flange back adjustment

Screws for flange back adjustment

③

1/4-20 UNC

Camera mount hole

④

Lens connector

For auto iris (DC or Video)

⑤

D-SUB 9 pin connector

For DC+12V,Video out & RS-232C

⑥

LED Power indication

⑦

BNC Composite video output(NTSC or PAL)

⑧

Function keys

For camera configuration

⑨

RJ-45

Ethernet connection (100BASE-T,10BASE-T)

Power over Ethernet

⑩

Holes for RJ-45

Holes for fixing screws of RJ-45 (note 2)

⑪

LED (ACT.)

Network connection (ACT.)

⑫

LED (LINK)

Network connection (LINK)

Fig.1 Locations

Note 1) Use the provided C-mount adapter for C–mount lenses

Note 2) When an RJ -45 cable with thumbscrews is connected to the camera, please do not

excessively tighten screws by using a screwdriver. The RJ-45 receptacle on the

camera might be damaged. For security, the strength to tighten screws is less than

0.147 Newton meter (Nm). Tightening by hand is sufficient in order to achieve this.

④

⑤

⑥

⑦

⑧

⑨

⑩

⑪

⑫

③

①

②

②

CV-S3500E

- 7 -

4.2. LED indication

4.2.1 Power indication

● Green light: Power ON and it is ready to use.

4.2.2 LED (LINK)

● Green light: Connecting with 100BASE-T or 10BASE-T

4.2.3 LED (ACT)

● Orange light: Standby for 100BASE-T connection
 Orange flashing: Comm unicating in 100BASE-T

Note: In case of 10BASE-T connection, LED does not light.

CV-S3500E

- 8 -

5. Pin Assignment

5.1. D-SUB 9-pin multi-connector (DC-in/Video/RS-232C)

Fig. 2. D-SUB 9-pin connector.

5.2. RJ-45 Ethernet Connector

12345678

Fig. 3. Ethernet connector

Note: When PoE is used, Cat5 or better cable should be used.

5.3. Auto iris lens connector

Type: EIAJ RC-5204

1

324

Fig.4 Auto iris connector

Pin no.

Signal

Remarks

1

GND

For DC input

2

+12 V DC input

3

GND

4

Video out (VBS)

*1

5

NC

6

Y output

7

C output

8

RS-232C TXD output

9

RS-232C RXD input

*1 : This video output is the same as BNC. Both outputs

cannot be used simultaneously.

Pin No

10BASE-T/100BASE-T

POE

In/out

1 TX+ Alternative A+

2

TX-

Alternative A+

3

RX+

Alternative A-

4

Not used

Alternative B+

5

Not used

Alternative B+

6

RX-

Alternative A-

7

Not used

Alternative B-

8 Not used Alternative B-

Pin No

DC Control ( Passive )

1 D amp -

2

D amp +

3

Drive +

4 Drive -

CV-S3500E

- 9 -

6. Connections

6.1. Power

Power to the CV-S3500E is supplied through the D-SUB 9 pin or the RJ-45 Ethernet interface. The
power consumption of the CV-S3500E is less than 4.2W.

Fig.5 Power supply

The PoE system in the CV-S3500E is Alternative A, which uses data communication lines as power
supply. For connection details, refer to section 5.2.

6.2. Video output (NTSC or PAL)

The CV-S3500E provides composite video and YC video for NTSC or PAL.
BNC output and D-SUB 9-pin output for composite video cannot be used at the same time.

Fig.6 video output
NTSC or PAL o utput can be selected from the on-screen menu which can be activated by the
functi o n keys on the back of the camera.

6.3. Ethernet connection

The CV-S3500E works as an IP network camera, providing JEPG, MPEG4 or H.264 motion video or
JPEG still pictures. Using a web browser, the camera can be configured for different applications.

Fig.7 Ethernet connection

6.3.1 MAC add ress and IP add ress

When connecting to a net work, please check MAC address and IP address.
MAC address Indicated on the bottom of CV-S3500E

IP address Set in accordance with the connected Network
DHCP can acquire appropriate IP address if DHCP function is set to ON.

The following table shows IP addr ess default settings.

Item

Default

IP Address

192.168.30.30

Subnet Mask

255.255.255.0

Default Gateway

0.0.0.0 (not used)

DHCP

OFF

LINK ACT .

POWER /T R IG

V ID EO OUT

RS -232C/DC IN SYNC/

UP

OD WN

FUNC

100 BASE-TX10 BASE-T/

Pin3 Gnd
Pin4 NTSC or
PAL out
Pin6 Y out
Pin7 C out

D-SUB 9 pin

NTSC or PAL
putput

LINK ACT .

POWER /T R IG

V ID EO OUT

RS -232C/DC IN SYNC/

UP

OD WN

FUNC

100 BASE-TX10 BASE-T/

Pin1 Gnd
Pin2 +12V

D-SUB 9 pin

POE
(Power over Ethernet)

LINK ACT .

POWER /T R IG

V IDEO OU T

RS -232C/DC IN SYNC/

UP

OD WN

FUNC

100 BASE-TX10 BASE-T/

100BASE-T/10BASE-T

CV-S3500E

- 10 -

6.3.2 Automatic acquisition of RTC time (SNTP)

The CV-S3500E can acquire RTC time through the network. Set IP address of the SNTP time

distribution server.

6.3.3 User acc ess

Access via HTTP can be controlled by registered ID and Password. In the default setting,

they are not registered. Three user levels can be set: administrator, operator and viewer.

6.3.4 Setup menu

Checking network addresses, setting DHCP, and other task s can be done through function
keys located on the rear of the camera. Please refer to section 7.3 for the setup menu tree.

6.3.5 Image format through Ethernet interface

In the CV-S3500E, the CCD is scanned in two modes, one for 1280 x 960 and the other for
960 x 720. Data can be digitized in two scan modes. This is done by selecting the scan
mode.

Image types available through the Ethernet interface are shown in the following table.

Still/Movie

Format

Scan mode

select

Image size

NTSC/PAL

mode

Frame

rate

Bit rate

Still image

JPEG or

Non­Compression

1280 x 960

1280 x 960

- - -

960 x 720 960 x 720 - - -

640 x 480

- - -

Moving

image

Motion JPEG
1280 x 960

1280 x 960

1 to 2

fps

Normal/High/Super

960 x 720 960 x 720

MPEG4
1280 x 960

640 x 480
NTSC

15 fps

PAL

12.5 fps

960 x 720 640 x 480 NTSC 30 fps

PAL

25 fps

H.264
1280 x 960

640 x 480
NTSC

15 fps

PAL

12.5 fps

960 x 720 640 x 480 NTSC 30 fps

PAL

25 fps

Note:

1. The performance of motion video through the network depe nds on the traffic conditions of the

network or graphic performance in the PC.

2. RTP movie transfer uses wideband network bandwidth. Accordingly, there may be limitations

in the network.

3. Using HTTP motion video (1280x960), if the quality is set at “super”, the analog output may be

interrupted.

4. If using RTP JPEG and JPEG still image at the same time, the still image is not activated (no

memory error). If using the JPEG still image, RTP should be set at MPEG4 or H.264.

CV-S3500E

- 11 -

7. Camera configur at ion – OSD (On Screen Display)

The CV-S3500E camera has an on-screen display in order to set up the camera parameters. The
setup function keys are located on the back of the camera.

Fig.8 Functi on keys

No.

Name

Function

1

UP key

Select the item as moving upward

2 FUNC key 1.Press and hold to access th e o n-screen menu

2.Advance through menu items for setting with the UP or DOWN button

3 DOWN key Select the item by moving downwards

7.1. Top menu

When pressing “FUNC” button for a few seconds, 「CAMERA」top menu appears on the screen.
There are three top menus, CAMERA, SET UP and OFF.

Fig.9 CAMERA TOP menu

In order to set “CAMERA”functions, push “FUNC” again. Then, the camera functions described in
section 7.2 appear on the screen.

Push “FUNC” button

CAMERA

Fig.10 To start the set-up of the CAMERA functions

①

②

③

CV-S3500E

- 12 -

If “UP” button is pressed, the menu is changed to “SET UP”.

SET UP

Push “UP” button

Fig.11 Change the menu to “SET UP”

Press “FUNC” button to set up the SET UP functions.

SET UP

Push “FUNC” button

Fig.12 To start the setup of the SET UP functions
In order to set the screen OFF, press “DOWN” button.
Please note that the FUNC button works only to move forward in the menu sequ ence. It can not be

used to move backwards in the menu sequence.
If “OFF” is shown on screen, pressing the “FUNC” button turns the “Menu” OFF.

CV-S3500E

- 13 -

7.2. CAMERA menu tree

CAMERA

WHITE BALANCE

SHUTTER

AGC

BACK LIGHT

IRIS LEVEL

INTEG.

SHARPNESS

GAMMA

AUTO

ONEPUSH

MANUAL

3200K

4500K

5600K

OFF

1/100

1/250

1/500

1/1000

1/2000

1/4000

1/10000

CCD IRIS (AUTO EXPOSURE)

OFF

MANUAL

12dB MAX

24dB MAX

OFF

PAT 1

PAT 2

PAT 3

DARK ------------- LIGHT

OFF

X2

X4

X6

X8

LOW

HIGH

0.45

0.6

1.0

“FUNC”

Button

“UP” or　”DOWN”

Button

Menu OFF

Fig.13 CAMERA menu tree

CV-S3500E

- 14 -

7.3. SET UP menu tree

The following is the menu tree for SET UP settings. The “FUNC” butt on can advance through the
main setting items while the “UP and DOWN” but ton s can be us e d t o select an appropriate setting.

SET UP

SCAN MODE

H-MIRROR

D-ZOOM

TV-SYSTEM

1280 x 960

960 x 720

OFF

ON

NTSC

PAL

IP_ADR

DHCP

SNTP

192.168.30.30

OFF

ON

OFF

ON

OFF

ON

MAC_ADR

00-01-DF-05-XX-XX

Menu OFF

“FUNC” button

“UP” or “DOWN”

button

SUBNET_MASK

255.255.255.0

Fig.14 SET UP menu tree

CV-S3500E

- 15 -

7.4. Descriptions of camera functions

BACKLIGHT

OFF
PAT1
PAT2
PAT3

Back Light Compensation
This is used with auto iris and/or AGC.
OFF : Average photometry
PAT1,PAT2 and PAT3 use weighting on the total image.

PAT 1 uses the center weighting, PAT 2 uses the center

weighting with less weighting on surrounding areas and PAT3
is weighted in the middle and lower part of the picture (refer
to the following drawings).

PAT 1

PAT ２ PAT ３

Large weighting Small　weighting No weighting

Fig.15 Conceptual drawing of weighting pattern of backlight compensation

INTEG. MAX

OFF

Standard mode

X2 Maximum two times integration

X4

Maximum four times integration

X6

Maximum six times integration

X8 Maximum eight times integration

Note: INTEG. MAX is a high sensitivity mode using longer integration times .
If the objects are moving, the images will be blurred.
INTEG. MAX is a maximum for integration time and this is controlled

automaticall y. The integratio n time changes depending on the objects.

D-ZOOM

ON or OFF Digital Zoom

OFF

Factory default

ON

Digital zoom is ON. Two times enlargement for both H and V.

SCAN MODE

Select scanning modes

1280x960 Factory default

CCD scan format is 1280 x 960 @

15 fps frame rate. This

original image is converted to NTSC (30 fps) or PAL (25 fps) or
outputs through Ethernet..

960x720

CCD scan format is 960x720 @ 30 fps frame rate. T his original

image is converted to NTSC (30fps) or PAL (25 fps) or outputs
through Ethernet.

CV-S3500E

- 16 -

H-MIRROR

OFF

Factory default

ON For left and right reversed image

8. Camera Configuration – RS-232C

8.1. RS-232SC Interface

Communication speed

38400 bps

Data length

8 bit

Parity

None

Stop bi t

1 bit

Flow

None

Type

Asynchronous

8.2. Download and i nstall CV-S3500E camera control tool

CV-S3500E camera cont rol tool can be downloaded at www.jai.com.

C l ick CV-S3500_ver100_T0112.msi and follow the screen described below.

After the installation is completed, two tools, “CV-S3500E” and “NetCam Search” are

created.

“CV-S3500E” controls the camera functions b y RS-232C serial communication.
“NetCam Search” is a tool for Netwo rk operation. This is not normally used. It is
for:

 When the IP address set by the DHCP server is needs to be known
 To access the informatio n for MAC_ADR/IP_ADR/Camera Model Name/Firmware

Version

CV-S3500E

- 17 -

8.3. Camera control tool
Connect the CV-S3500E and execute the camera control tool.

The following communication window comes up.

The default setting of port is “AUTO” and the camera control tool automatically searches

for the appropriate port.

Click o n the “Camera” tab to configure the camera settings.

CV-S3500E

- 18 -

Click the “Capture” tab and the screen for setting the RTP and HTTP movie image format
is opened. (Set the data volume and picture quality of the transferred image through
Ethernet)

Settings can only be made on fields that are not “grayed out”.

Click “D -zoom” to set up the digital zoom function.

CV-S3500E

- 19 -

Click “Network” to confirm the current network settings.
When the CV-S3500E is connected to the network, the following is the default setting.
If changes are needed, open the PC’s “Control Panel” and clck on “Network connection”,
“Local area network” , “Property”, “Internet protocol /TCP/IP” and “Property”. In the
property window, set the appropriate IP address and subnet mask for the system.

Click “Time” for setting the date and time. If it needs to be automatically synchronized,
set SNTP server ON.

CV-S3500E

- 20 -

Click “Reset” for camera reset or EPROM reset.
“Reset only” works as camera powers ON or OFF.
Click “EEPROM Preset Default_Reset” and click “Exec” button in order to reset the
EEPROM to the default settings.

Click “User” fo r specific user settings.
This sets the access level and password for users.
The user level is as follows.
Administrator :Full access
Operator :Camera settings and Image viewing
User :Image viewing only

The setting fields must be more than one letter and less than 8 letters.

CV-S3500E

- 21 -

9. Camera configur at ion and how to use web browser

In order to set up the camera configuration and watch the picture, it is necessary to install the
following software.

Quick time player 7.1 & later : To watch the picture
IE 6/7/8 or Firefox 3.0 or Quick time 7.1 & later : To configure the camera

The following explanation describes the procedure using IE and Quick time. If the PC is not
equipped with all the mentioned software, it is necessary to install it.

9.1. Initial settings

IP address setting

Set IP address at the default address of the CV-S3500E.
There are t w o ways to set IP add ress.

1. Set IP address manually

2. Obtain an IP address automatically (Use DHCP server)

9.1.1 Set IP address manually

Th e fixed IP address (default) of CV-S3500E is as follows (DHCP is OFF)

IP address : 192.168.30.30
Subnet mask : 255.255.255.0
Default gateway : none

Set IP address of PC in order to communicate between PC and CV-S3500E

1. Set IP add ress in the PC
Follow “Start” →”Control panel” → “Network connections” → ”Local area

connection”
and “Properties”.

2. In the properties screen, check that “Client for Microsoft Network” and “Internet
protocol(TCP/IP)” are selected.

3. Select “Internet protocol (TCP/IP)” and click “Properties”.

Set IP address as follows.

CV-S3500E

- 22 -

 Select “Use the following IP address”.


Start Internet Explorer.
Set URL as http://192.168.30.30

The input window for user name and password will come up on the screen.











Set IP addre s s. As CV-S3500E default IP

address is 192.168.30.30, set 192.168.30.33 as

an example.
Note: Do not use the same IP address in the
network.

 Check Subnet mask.
The default is 255.255.255.0.

 It is not necessary to set Default gateway.
 Click OK.







Input the user name.

The default is “Admin”.
 Input password.

The default is “Admin”.

 Click “OK”.



CV-S3500E

- 23 -

9.1.2 Obtain an IP address automatically.

In order to obtain as IP address from the DHCP server, the following procedure is needed.

1. Follow the procedure in section 9.1.1 to start the camera menu.

2. Click “N etwork” tab in the SetUp menu and check “DHCP” as “ON” .

3. Then, using NetCamSearch, check the IP address.

4. Then, set the IP address using the procedure described in the section 9.1.1.

5. Start Internet Explorer and log in as Administrator.

9.2. TOP menu

Then, the following camera control tool will come up on the screen.
This is the TOP menu. Select View Camera or SetUp Menu tab.

“View Camera”
This is for selecting the image transfer format.

“SetUp Menu”
This is for setting up the network and camera functions.

CV-S3500E

- 24 -

9.3. View Camera top menu

The following is the TOP menu for view camera

Se l ect the item in the sub menu.

Movie-view (RTP)
Movie-view (HTTP-JPEG)
Still capture(JPEG)
Still capture(BMP)

Note: On Movie-view (RTP) mode, It will take time until the QuickTime player p lug in is
initiated. Click the PLAY button, RTP transfer will begin.

Note: When you select both JPEG in RTP and JPEG in General File under Still image, a JPEG
still image cannot be captured. In RTP, MPEG4 or H.264 should be selected.

In this case, the following indication appears on the screen if JPEG/Still is selected．
In the case of an HTTP movie, the movie and still image can be captured at the same time.

Note: Still-capture(YUV422) (YUV422 RAW data) or Still-capture(DNG-YUV422)(YUV422-DNG
data) can also be transferred. The ordinal browsers do not support these formats, t hey
cannot be displayed but data will be transferred for storing. When DNG or YUV is selected,
an additional window will open to ask the user to search for the appropriate software to
watch these files.

CV-S3500E

- 25 -

9.4. SetUp top menu

This is the TOP menu for Setup. Select the items listed acr oss the tab.

9.4.1 SetUp-D Zoom

The following window is to used to set digital zoom ON or OFF, to set zoom position, and
zoom
area.

9.4.2 SetUp-Camera

The foll owing window is used to set up camera parameters, scan format, and TV format.

CV-S3500E

- 26 -

9.4.3 SetUp-capture

This window is used to set up the size and quality of the captured image in order to use
the Network effectively.
RTP:
The compression formats for RTP(Real Time Transport Protocol) are JPEG, MPEG4 and

H.264.

In this case, the imag e size is VGA which is 640 x 480.
Accordingly, the bandwidth (data volume) depends on picture quality (compression rate).
The picture quality can be selected, normal, high or super.
The picture quality becomes better from normal to super, but the data volume will
also increase.

9.4.4 SetUp-Network

This is for setting DHCP, IP address and Subnet mask.

The settings do not become effective until “Reload” is pressed.

When DHCP is used, the IP server address of DHCP, the camera’s IP address and Subnet mask

are automatically set and the settings are indicated.

For setting up the camera’s IP address, follow the procedure described in section 9.1.2.

CV-S3500E

- 27 -

9.4.5 SetUp-Time

This is for setting up the date and time. If the SNTP server can be accessed, input IP address.

After SNTP is ON, reload the new settings data.

9.4.6 SetUp - Reset

Click “Reset” for camera reset or EPROM reset.
“Reset only” works as the camera powers ON or OFF.
Click “EEPROM Preset Default_Reset” and click “Exec” button in order to reset the
EEPROM to its default settings.

CV-S3500E

- 28 -

9.4.7 SetUp-User

Set the ID and password for the Default Administrator.

For users 1 through 5, the Acces s level can be set .
Administrator All operating functions are accessible
Operator Possible to operate camera
Viewer Can only view images
One letter to 8 letters can be used for the name and password.

CV-S3500E

- 29 -

10. External Appearance and Dimensions

40

LENS

29

LINK ACT.

V IDEO OUT

UP

ODWN

FUNC

55

55

CS Mount

(12.7)

100BASE-TX10BASE-T/

27.5

30.5

(91.7)

2-U1/4-20

2-M2.6 79

(1)

/DC IN YC OUT RS-232C/

POWER

Outside size tolerance：±0.3mm

CV-S3500E Outside drawing

Fig.16 Outline

CV-S3500E

- 30 -

11. Specifications

11.1. Spectral se nsitivity

0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1

400 500 600 700 800

Relative Camera Sensitivity

Wavelength ( nm)

Rch

Gch

Bch

Fig.17 Camera spectral sensitivity

CV-S3500E

- 31 -

11.2. Specifica tions table

Specifications CV-S3500E

Camera

TV system

NTSC or PAL

CCD

Image size

1/3 interline transfer CCD

Total pixels

1348(H) x 976 (V)

Effective pixels

1296(H) x 966(V)

Active pixels 1280(H) x 960(V)

Image size

4.8mm(H) x 3.6mm(V)

Cell size 3.75um(H) x 3.75um(V)

Clock frequency 36 MHz

Scanning system

NTSC

PAL

CCD scanning Progressive Scan

Full pixels:15 fps

Center ROI：960 x 720：30 fps

Progressive Scan

Full pixels:12.5 fps

Center ROI：960 x 720：25 fps

Vertical resolution

480 TV lines

580 TV lines

Horizontal resolution

520 TV lines

520 TV lines

Sensitivity

1280lx (AGC OFF,f/8)

1080 lx (AGC OFF,f/8)

Minimum illumination

1.4 lx (+24dB, 50% video)

1.2 lx (+24dB, 50% video)

S/N

More than 50dB (AGC off）
Output scan system 2:1 interlace
Horizontal frequency 15.734kHz 15.625kHz
Vertical frequency 59.94Hz 50Hz
Electronic shutter OFF, 1/100, 1/250, 1/500, 1/1000,1/2000,1/4000,1/10000

& Auto shutter

Video output（BNC） Composite Video ：1Vp-p 75Ω

Video output

（D-sub 9pin）

Y/C Component ：Y 1Vp-p 75Ω

C 0.3Vp-p 75Ω

and Composite Video ：1Vp-p 75Ω

(Can not be used together with BNC output )
Image output
（Ethernet 100Base）

MPEG4 or H.264 or JPEG

Synchronization

Internal

Gamma

0.45, 0.6, 1.0 selectable

White balance

Auto/One Push Auto(2800 to 6700K)

Manual（3000K～7800K）

Pre-set （3200K, 4600K, 5600K）

Gain

AGC Max12dB /AGC Max 24dB/ Manual range from 0dB to 24dB

Setup level

7.5IRE

50 mV

White clip

Adjusting range 700～763mV

Back light compensation

OFF, Pattern1, Pattern 2, Pattern 3

Horizontal Mirror

ON/OFF

Note: Only for analog output

Electronic zoom

X2 with ON/OFF, In any place in the image

Note: Only for analog output and RTP movie

High sensitivity mode

OFF, 2X, 4X, 6X, 8X

Lens mount

CS mount (C mount adapter provided as an accessory)

Lens Auto iris drive

DC drive or video iris ( Selectable by DIP switch)

Back focus mechanism

Built-in

CV-S3500E

- 32 -

General

Communication Interface

OSD and rear button switch or Ethernet (web browser) or RS-232C

Power supply

DC 10.8V to DC 26.4V D-sub or Power over Ethernet

Power consumption

Less than 4.2W

Operating Temperature

-5°C to +45°C

Operating humidity

20% to 80% （non-condensing）
Regulations CE(EN61000-6-2, EN61000-6-3), FCC Part15 Class B
Dimensions 55(w) x 55(h) x 78(d)mm (excluding protrusions)
Weight Less 350 g

Network part

Still image

File format

JPEG, BMP, RAW Data, DNG

Compression JPEG, Non-compression

Format

Y, Cb, Cr 4:2:0

Pixel Size 1280 x 960, 960 x 720, 640 x 480

Compression rate

Normal/High/Super

Note: Normal is highest compression rate.

Moving image

Compression

Motion JPEG, MPEG4, H.264

Format

Y, Cb, Cr 4:2:0

Pixel Size

Still Motion JPEG : 1280 x 960, 960 x 720

MPEG4, H.264, RTP, Motion JPEG : 640 x 480

Frame rate

(Note)

Still Motion JPEG : 1 to 2 fps

MPEG4, H.264, RTP Motion JPEG:15/30 fps, 12.5/25fps

Bit rate

Normal / High / Super

Note: Normal is lowest bit rate.

Network

Network interface

10 BASE-T, 100BASE-T auto/fixed

PoE

Hardware base

Network protocol

IPv4,ICMP,IGMP,ARP,TCP,UDP,RTP/RTCP

Access control Users Max 6(Def Admin 1 + User 5)

3 User Levels Admin/Operator/Viewer

Compression and

pixel size

JPEG : 1280 x 960, 960 x 720, 640 x 480

JPEG/MPEG4, H.264 : 640 x 480 RTP

Compression and

transfer protocol

Motion JPEG, MPEG4, H.264 (RTP)

JPEG (HTTP)

BMP (HPPT)

YUV422-Raw (HPPT) (YUV 422 raw data)

YUV422-DNG (HTTP) (Developed by Adobe systems)

Camera Control Web Browser

(IE6/7/8, Firefox3, QuickTime 7.1)

RTP moving image QuickTime Player ver.7.1 and after

HTTP moving image

IE6.0 and after

Note:

1. DHCP works as a client

2. HTTP works as a server

CV-S3500E

- 33 -

Appendix

1. Precautions

Personnel not trained in dealing with similar electronic devices should not service this camera.
The camera contains components sensitive to electrostatic discharge. The handling of these
devices should follow the requirements of electrostatic sensitive compo nent s .
Do not attempt to disassemble this camera.
Do not expose this camera to rain or moisture.
Do not face this camera towards the sun, extreme bright light or light reflecting objects.
When this camera is not in use, put the supplied lens cap on the lens mount.
Handle this camera with the maximum care.
Operate this camera only from the type of power source indicated on the camera.
Power off the camera during any modification, such as changes of jumper and switch settings.

2. Typical Sensor Characteristics

The following effects may be observed on the video monitor screen. They do not indicate any
fault of the camera, but are associated with typical sensor characteristics.

V. Aliasing

When the CCD camera captures stripes, straight lines or similar sharp patterns, a jagged image
may appear on the monitor.

Blemishes

All cameras are shipped without visible image sensor blemishes.
Over time some pixel defects can occur. This does not have a practical effect on the operation of
the camera. These will show up as white spots (blemishes).
Exposure to cosmic rays can cause blemish es to appear on the image sensor. Please take care to
avoid exposure to cosmic rays during transportation and storage. It is recommended using sea
shipment instead of air flight in order to limit the influence of cosmic rays on the camera. Pixel
defects/blemishes also may emerge due to prolonged operation at elevated ambient temperature,
due to high gain setting, or during long time exposure. It is therefore recommended to operate
the camera within its specifications.

Patterned Noise

When the sensor captures a dark object at high temperature or is used for long time integration,
fixed pattern noise may appear on the video monitor screen.

3. Caution when mounting a lens on the camera

When mounting a lens on the camera dust particles in the air may settle on the surface of the lens
or the image sensor of the camera. It is therefore important to keep the protective caps on the
lens and on the camera until the lens is mounted. Point the lens mount of the camera downward
to prevent dust particles from landing on the optical surfaces of the camera. This work should be
done in a dust free environment. Do not touch any of the optical surfaces of the camera or the
lens.

4. Exportation

When exporting this product, please follow the export regulation of your own country.

5. References

1. This manual and datasheet for the CV-S3500E can be downloaded from www.jai.com

2. Camera control tool can be downloaded from www.jai.com

CV-S3500E

- 34 -

Change history

Date

Revision

Changes

Sept. 2010

Ver.1.0

New release

CV-S3500E

- 35 -

User's Record

Camera type: CV-S3500E
Revision: ……………..
Serial No. ……………..
Firmware version. ……………..

For camera revision history, please contact your local JAI distributor.

User's Mode Settings.

User's Modifications.

Company and prod uct na mes me nti on ed in this manual are trademarks or registered trademarks of their respective owners.
JAI A-S cannot be h el d responsible for any technical or typographical errors and reserves the right to make changes to products
and documentation without prior no tification.

Europe, Middle East & Africa Asia Pacific Americas

Phone [phone]
Fax [phone]

Phone [phone]
Fax [phone]

Phone (toll-free) [phone]
Phone [phone]

Visit our web site at www.jai.com