Jaga JRT-200 Installation, Setup & User Manual

Jaga Room Thermostat JRT-200 installation, setup & user manual

Features

• for 2- and 4-pipe fan coil systems

• heating and cooling mode (4-pipe)

• heating and cooling mode (2-pipe)

• automatic or manual fan speed control

• surface-mounting

• 2 programmable time zones

• 0-10V output

• valves 24V AC/DC or 230VAC

• it is possible (at manual control) to allow the fan to run once “set point” is
reached

Technical Data

Power Supply 24V AC/DC

Power Consumption 200 mA

Set Point Range +10 > +40°C

Ambient 0 > +40°C

Relative Humidity 85% max

Backlight Blue

Sensor NTC 10K

Accuracy + 1°C (step control by +0.5°C)

Protection Class IP30

Housing ABS to UL94-5 fire retardant plastic

Product-documentation:

• this manual is an integral part of the unit and must be handed over to the user
after the installation of the device is completed in order to comply with applicable
legal requirements.

• please read the manual carefully so that you understand the information in order
to ensure safety during installation, use and maintenance.

• no liability is accepted for damage resulting from non-compliance with the
guidelines in this installation manual.

Dimensions

M

M

4.25

6.5

3 2.8

9.3

14

9.7

13.4

1.21.4

0.4

CE-mark

The CE-mark symbolizes the compliance of the device with the following guide­lines:

• EN 61000-6-3:2007+A1:2011

• EN 61000-3-2:2006+A1:2009+A2:2009

• EN 61000-3-3:2008

• EN 61000-6-1:2007

IMPORTANT: This manual will guide you through the installation, setup and use of the Jaga Room Thermostat JRT-200. Keep this manual in
a safe place for future reference.

JR T-2 00

ATTENTION !!

1.5 m

The room thermostat must be installed at approx.

1.5 m above floor and out of reach of external influ­ences such as direct sunlight, draught or other heat
sources as they may impede the correct functioning
of the thermostat. Nearby electric fires, televisions,
wall or table lamps may prevent the thermostat from
working properly.
Ensure that there will be enough space to allow easy
access to the two retaining screws, located at the bot­tom of the wall plate.

6

2.8

Mount the JRT-200 Room thermostat on a wall re­cessed box (60.3 mm fixing centers) or direct onto a flat

wall using wall plugs.

Deze handleiding in het NEDERL ANDS:
Ce manuel en FRANÇAIS:
Dieses Handbuch auf DEUTSCH:
This manual in ENGLISH:

www.jaga.be/downloads/Briza/Manual_JRT200.pdf

25 juni 2018, 8:45 - Jaga N.V.

Jaga Room Thermostat JRT-200 installation

Installation

WIRING: Warning: The installation of the thermostat should be performed by qualified personnel and must comply with the applicable

local and national electrical codes and utility requirements. All wire connections must be tightened and properly arranged to prevent
a shortcircuit. Turn off the power at the electrical panel to prevent electrical shock or product damage.

To remove the wall plate, use a Phillips
screwdriver to loosen the two screws from
the bottom of the wall plate

Remove the front panel When not using a recessed conduit box:

• mark out and drill the holes

• screw the device to the wall.
The type of wall, solid or cavity, determines

the type of screw or plug that is used.

24V AC/DC

M

1234567891011

M

M

• flush wiring can enter from the rear
through the aperture in the wall plate

• connect the JRT-200 according the wiring
diagrams** on this page

Reassemble the front panel Tighten the screws with a Phillips screwdriv-

er. (Do not over-tighten.)

Warning: Turn off the power at the electrical panel to prevent electrical shock or product damage.

** Wiring diagram

2-Pipe 4-Pipe

1234567891011

1234567891011

H/C VALVE

0...10V

COM

0...10V

COM

KEY CARD

-

+

L

N

24V / 220VAC

DC 24V

DC 24V

C VALVE

H VALVE

KEY CARD

-

+

++-

-

L

N

24V / 220VAC

1234567891011

0...10V

COM

DC 24V

C VALVE

H VALVE

KEY CARD

-

+

+

-

L

N

24V / 220VAC

H/C Heating / Cooling C Cooling

H Heating GND N

25 juni 2018, 8:45 - Jaga N.V.

Jaga Room Thermostat JRT-200 setup / user

Control panel

Clock

Programming & week / day On / Off

Room temperature

Set temperature

M

1 2 3 4 5 6 7

h

ROOM

SET

°C

1 2 3 4

Temperature /
parameter setting

Fan Speed setting

Fan speed:

Temperature /
parameter setting

Heating / cooling

• Low

• Mid

• High

• Auto fan

Heating

Cooling

Programmable Time setting

• press the “M” button for 5 seconds to enter clock setting ( ) and day setting

• enter 5+1+1 programmable mode

• press “+” and “-“ to set the thermostat on/off time

• next mode setting: toggle trough the menu with the “M” button. Activate the programmed time: press and hold the “ “ button for 5
seconds.

To deactivate the programmed time: press and hold the “ “ button for 5 seconds

Week

1st time zone 2nd time zone

Turn on Turn Off Turn on Turn Off

Icons

1

2 3 4

2

3 4

3

4

4

12345 (Monday~Friday) 8:30 12:00 14:00 18:00

6(Sat.) 9:00 12:00 15:00 18:00

7(Sun.) 9:00 12:00 15:00 18:00

21/12/ 2018, 8:45 - Jaga N.V.

Wiring connections

Disconnect the power supply before making wiring connections, to prevent electrical shock and equipment damage.

Jaga Room Thermostat JRT-200 installation manual

2-Pipe system 4-Pipe system

Briza
Clima Canal
Quatro Canal

....

- 24 VDC

+ 24 VDC

0..10 V

L

+ -

N

230 VAC
L1 N

+-

+-

1234567891011

H/C VALVE

COM

KEY CARD

L

N

24V / 220VAC

DCV24

0...10V

Briza
Clima Canal
Quatro Canal

....

- 24 VDC

+ 24 VDC

0..10 V

L

+ -

N

230 VAC
L1 N

Briza
Clima Canal
Quatro Canal

....

- 24 VDC

+ 24 VDC

0..10 V

L

+ -

N

230 VAC
L1 N

+-

+-

+-

+-

1234567891011

H/C VALVE

COM

KEY CARD

L

N

24V / 220VAC

24V DC

1234567891011

C VALVE

H VALVE

0...10V

KEY CARD

L

N

24V / 220VAC

DCV24

COM

0...10V

H/C Heating / Cooling C Cooling

H Heating GND Ground

Parameter settings

• set Power Off, bij pressing the “ ” button

• to access the MENU , press and hold “M” and “+” buttons simultaneously for 10 seconds until „ “ displays. Press “+” and “-“ to change the
settings.

• toggle trough the menu with the “M” button

Menu Description Range

01 Temp. Offset -8 °C > +8°C, in steps of 0.5 ° C

03 Set Point High Limit +10 °C > +40°C, in steps of 0.5 ° C

04 Set Point Low Limit +10 °C > +40°C, in steps of 0.5 ° C

05 Display setting Room/Set (default Room)

06 Dead Band 0°C > +3°C (default 0,5°C)

07 Programmable Time setting: temperature +10 °C > +20°C, in steps of 0.5 ° C

09 Key-card select NO/NC (default NO)

10 Re-power status keep (default 1) 0:non keep 1:keep

11 2-pipes/4-pipes select 2/4 (default 4)

12 Fan output (0-10V) select dead band or not 0: with dead band 1: without dead band (default 0)

13 Heating / Cooling / Heating + Cooling Heating + Cooling default

14 80% - 90% - 100% fan speed 100% def ault

15 Back to factory settings

Select 0 or 1 (recovery) with the + and - buttons. After selecting “1”,
press the “

” button to go to the startup screen. Recovery is success-

ful.

16 Software version 107D