Jaga JRT-100 Installation, Setup & User Manual

Jaga Room Thermostat JRT-100 installation, setup & user manual

JR T-100

ATTENTION !!

1.5 m

The room thermostat must be installed at approx.

1.5 m above floor and out of reach of external influ­ences such as direct sunlight, draught or other heat
sources as they may impede the correct functioning
of the thermostat. Nearby electric fires, televisions,
wall or table lamps may prevent the thermostat from
working properly.
Ensure that there will be enough space to allow easy
access to the two release locks, located at the bottom
of the wall plate.

1.43.4

6

Mount the JRT-100 Room thermostat on a suitable box
(60.3 mm fixing centers). Minimum depth of 45mm. The
internal size of the wall recess box must be at least
Ø60mm or 50x50mm.

Features

• for 2- and 4-pipe fan coil systems

• (4-pipe): heating and cooling mode

• (2-pipe): heating and cooling mode

• automatic or manual fan speed control

• semi-recessed mounting

• 2 programmable time zones

• 0-10V output

• for valves 24V AC/DC only

• optional external room temperature sensor (order code: 24800.00053032)

• it is possible (at manual control) to allow the fan to run once “set point” is
reached

Technical Data

Power Supply 24V AC/DC

Power Consumption 200 mA

Set Point Range +10 > +40°C

Ambient 0 > +40°C

Relative Humidity 85% max

Back-light

Sensor NTC 10K

Accuracy + 1°C (step control by +0.5°C)

Protection Class IP30

Housing ABS to UL94-5 fire retardant plastic

Product documentation:

• this manual is an integral part of the unit and must be handed over to the user
after the installation of the device is completed in order to comply with applicable
legal requirements.

• please read the manual carefully so that you understand the information in order
to ensure safety during installation, use and maintenance.

• no liability is accepted for damage resulting from non-compliance with the
guidelines in this installation manual.

Dimensions

M

8.6

8.6

6 1.4 3.4

CE-mark

The CE-mark symbolizes the compliance of the device with the following guide­lines:

• EN 61000-6-3:2007+A1:2011

• EN 61000-3-2:2006+A1:2009+A2:2009

• EN 61000-3-3:2008

• EN 61000-6-1:2007

IMPORTANT: This manual will guide you through the installation, setup and use of the Jaga Room Thermostat JRT-100. Keep this manual in a
safe place for future reference.

Deze handleiding in het NEDERLANDS:
Ce manuel en FRANÇAIS:
Dieses Handbuch auf DEUTSCH:
This manual in ENGLISH:

www.jaga.be/downloads/Briza/Manual_JRT100.pdf

25 June 2018, 8:43 - Jaga N.V.

Jaga Room Thermostat JRT-100 installation

Installation

Warning: The installation of the thermostat should be performed by qualified personnel and must comply with the applicable local

and national electrical codes and utility requirements. All wire connections must be tightened and properly arranged to prevent a
shortcircuit. Turn off the power at the electrical panel to prevent electrical shock or product damage;

1.43.4

6

Install appropriate mounting box (60.3 mm
fixing centers).

Carefully remove the front plate:

• locate the (2) release locks on the bottom
edge of the front plate assembly. Use a
small flat head screwdriver to push each of
the release locks up to disengage the lower
clips of the front plate.

Swing the bottom of the front plate slightly
away from the bottom of the back plate.

987654321

Connect the JRT-100 according the wiring
diagrams* on this page.

Mount the thermostat base on the box and
secure it using two mounting screws. Do not
over-tighten.

Close the front plate:

• locate the upper clips into the slots at the
top of the grid plate

• insert the lower clips on the front plate into
the lower slots in the back plate. Press on
the cover plate until it locks

Warning: Turn off the power at the electrical panel to prevent electrical shock or product damage.

* Wiring diagram

2-Pipe 4-Pipe

1 2 3 4 5 6 7 8 9

1 2 3 4 5 6 7 8 9

0...10V

SENSOR

COM

0...10V

SENSOR

COM

24V DC

24V DC

C VALVE

H VALVE

H/C VALVE

L

+ -

N

230 VAC
L1 N

L

+ -

N

230 VAC
L1 N

+

-

+

-

1 2 3 4 5 6 7 8 9

0...10V

SENSOR

COM

24V DC

C VALVE

H VALVE

L

+ -

N

230 VAC
L1 N

+

-

H/C Heating / Cooling GND N

H Heating

Briza / Clima Canal / Quatro Canal ....

C Cooling

Optional external room temperature sensor

25 June 2018, 8:43 - Jaga N.V.

Jaga Room Thermostat JRT-100 setup / user

Programmable Time settings:

• hold the “M” button for 5 seconds to enter “clock setting” ( ) and “day setting”

• enter 5+1+1 programmable mode

• press “+” and “-“ to set the thermostat “on/off time”

• next mode setting: toggle trough the menu with the “M” button. Activate the programmed time: press and hold the “ “ button for 5
seconds.

To deactivate the programmed time: press and hold the “ “ button for 5 seconds

Week

1st time zone 2nd time zone

Turn on Turn Off Turn on Turn Off

Icons

1

2 3 4

2

3 4

3

4

4

12345 (Monday~Friday) 8:30 12:00 14:00 18:00

6(Sat.) 9:00 12:00 15:00 18:00

7(Sun.) 9:00 12:00 15:00 18:00

Control panel:

Programming & week / day Clock

Room temperature

Set temperature

Room temperature
Set temperature

Heating / Cooling Fan speed:

• Low

• Mid

• High

• Auto fan

Temperature / Parameter setting - / +

Fan speed Mode On / Off

Heating

Cooling

Sens or ↓

21/12/2018, 8:43 - Jaga N.V.

Parameter settings

• set Power Off, by pressing the “ ” button

• to access the MENU , press and hold “M” and “+” buttons simultaneously for 10 seconds until “ ” displays. Press “+” and “-“ to change the
settings.

• toggle trough the menu with the “M” button

Menu Description Range

01 Temp. Of fset -8 °C > 8°C

04 Set Point High Limit +10 °C > +40°C

05 Set Point Low Limit +10 °C > +40°C

06 LCD temperature display Room/ Room Set / Set (default Room)

07 Temperature setting / Program +10 °C ~ +20°C

11 Dead Band 0°C~+3°C (default 0,5°C)

12 NTC select Room: internal sensor / Floor: optional external room temperature sensor

13 2-pipes / 4-pipes select 2/4 (default 2 pipes)

14 (0-10V) select dead band or not 0: with dead band 1: without dead band (default 0)

15 Repower memory OFF/LAS T

16 Heating / cooling / heating + cooling heating + cooling default

17 80% - 90% - 100% fan speed 100% default

19 Back to factory settings

Re > press short “

” button

20 Software version

Jaga Room Thermostat JRT-100 setup