CLICK
JAGAUK cocoon 03.03
INSTALLATION INSTRUCTIONS
COCOON
Contents:-
Chrome
blank plug
Air Vent
Screws
Washers
Rawl Plugs
Always retain label
with element until installation
is complete. This will assist in
casing pack selection (see fig. 6)
Number of brackets
required for casing
lengths:-
40cm to 120cm = 2
140cm to 220cm = 3
240cm to 300cm = 4
Cut away ends of shrink wrap, remove fitting
kit and push fit brackets onto end element plate.
Illustration shows brackets fitted for right hand
connections.
Fit central
support feet
if unit is
140cm long
or above, see
instructions
packed with
feet.
H = 20.5cm (205mm)
from finished floor
H = 20.5cm (205mm)
from finished floor
Offer up unit and mark wall fixings,
positioning underside of heat exchanger
205mm above finished floor level
Number required for
casing lengths:-
40cm to 120cm = 0
140cm to 220cm = 1
240cm to 300cm = 2
FITTING PACK
POSITIONING DETAILS
RIGHT HAND CONNECTIONS LEFT HAND CONNECTIONS
HEATING ELEMENT
FIXING BRACKETS CENTRAL SUPPORT
FEET
(Kit is located within shrink
wrap of element)
Fig. 1
Drill 8mm holes, fit Rawl plugs
and screw unit to wall.
Fig. 4
Fit valves and connect pipe
work. Units can now be filled
and tested, but do not fit TRV
head at this point.
If top valves are being used
refer to instructions packed
with valve kits.
Fig. 5
Each front panel is 10cm high.
4 bracket nibs = 40cm plus
20cm to floor = casing height
required 60cm (600mm)
Element Label L50, Type 10
Casing pack
required 60. 50. 10.
HLD
When fixing and pipe work complete. Assemble casings as overleaf
Fig. 6
Fig. 2 Fig. 3
Alternatively,
if you need
left hand
connections –
turn bracket
through 180°
before clicking
onto heat
exchanger
205mm
Example. Casing pack selection.
INSTALLATION INSTRUCTIONS
COCOON CASING ASSEMBLY
See supplement sheet for 40cm length casings
Identification e.g. 60. 50. 10
60cm high
50cm length
10cm depth (type)
Top grille
Top panel
(chamfered
top edge)
Front panel
Lay front grille flat, fins facing
downwards. Position a front plate either
side, position with notches at bottom.
Clip together the three parts using front grille clips as
shown.
1. Press down centre of clip onto grille ensuring
tube grips locate correctly either side of grill tube.
2.3. then press ends of clip over lips of front panels
IMPORTANT! 40cm length casings use different style
of clip. See supplement sheet for figs 8 and 8A
Refer to section 8A for clip positions BEFORE assembly
Hang sub assembly
onto bottom nibs of
bracket.
Remember to remove
any remaining element
shrink wrap at this
point.
Assemble
remaining front
and top panels
Position each side
panel over the
lowest front panel
ensuring
protruding nib
hooks into notch.
Continue pressing
side panel
upwards until
your hear it
clearly snap into
place in the notch
in the top panel
Now fit the grille. The
double fasteners on the
underside of the plastic
corner piece, must be
pressed over the side
panel until you hear it
click into the slots in
the side panel.
Fit Phillips screws and
tighten them.
TRV head should now
be fitted together with
trims and blank plug.
Front grille clip
End panel blank plug
TRV aperture split rim
Top grille screw fasteners
Front grille
Side
Fig. 7
Fig. 8
Fig. 9
Fig. 11 Fig. 12
Fig. 10
CASING PACK
CASING COMPONENTS FITTINGS
CLICK
Once the casing is correctly
assembled, it will remain in
one piece and can be removed
and refitted as an assembly.
For further technical assistance telephone 01531 631533
Fig. 8A
Grille clips must be fitted in these positions.
View is from rear of grille when face down.
L.H. connections Casing Lengths R.H. connections
50cm
60cm
All longer lengths
on lengths
over 120cm
fit a 3rd
centre clip
IMPORTANT: 40cm length casings use different grille clip see
supplimentary sheet.
3
2
1
Loading...