Page 1
Introduction
We congratulate you on the purchase of your Atmos clock
and thank you for your confidence.
With no battery, electric current or winding, the Atmos clock
has been living on air since 1928. Radiating serenity and
pure design, it invites you to scrutinize the workings of its
gear-trains to try and discover their secret. Its glass cabinet
highlights the sheer genius of its mechanism.
We invite you to consult the operating instructions and we
wish you great pleasure with your Jaeger-LeCoultre clock.
A virtually perpetual movement
Leonardo da Vinci had already demonstrated that perpetual motion was not feasible – if only because of the laws
of physics. But it would have taken more to discourage the
researchers. These researchers included the Neuchâtel engineer Jean-Léon Reutter who, in 1928, designed a completely revolutionary clock drawing its power from variations in
the ambient temperature. It took yet a few more years of
research by our watchmaking firm to transpose this idea into
technical reality and patent it.The result came astoundingly
close to perpetual motion : the Atmos clock was born.
Its principle is amazingly simple. In a hermetically closed capsule is a gaseous mixture which expands when the temperature rises and contracts when it falls. Connected to the driving
spring, the capsule swells like the bellows of an accordion
and winds the clock movement up constantly. Between 15
and 30 degrees Celsius, a temperature fluctuation of a single
degree is enough to ensure an operating autonomy of about
two days.
The Atmos clock is designed so that no excessive resistance opposes this minimum power.The Atmos balance
wheel oscillates slowly, its lung breathing in perfect harmony
with temperaturevariationsanditshear tbeatingquietlytwicea
minute,i.e. 60 times less quickly than that of a traditional clock,
240 times less quickly than a wristwatch movement and
1,966,000 times less quickly than a quartz watch movement.
To get an idea of the delicacy of this minute energy transfer,
consider the fact that 60 million Atmos clocks together would
consume no more energy than a weak 15-watt electric light
bulb.
All the components of the Atmos clock are incredibly precise and dependable, so that it operates virtually without any
wear. It is therefore distinguished by its long service life which
-theoretically -can be as long as 600 years. Because of the
current state of air pollution, however, regular checking and
service are recommended.
The Atmos clock reconciles lovers of technical performance
and those for whom sobriety of shape or feats of craftsmanship are the predominant factors. In this respect, nothing
has changed. No Atmos clock can escape the five weeks of
checking and final adjustments which complete the work of
the Jaeger-LeCoultre master-watchmakers.
A unique gem of horological technology, the Atmos clock is
a timekeeper of distinction for Heads of State and numerous
sovereigns, because in this countr y unique in the world for
the perfection of its watches, it is a tradition to offer guests
of honour this Swiss horological masterpiece. This has been
the case for decades now, and the eminent recipients include
J.F. Kennedy,Winston Churchill,General de Gaulle and Charlie
Chaplin.
Atmos ClAssique
1. Expansion chamber 7. Return spring
2. Brass cover 8. Balance wheel
3. Balance spring (counterweight) 9. Elinvar® wire*
4. Small chain 10. Escapement
5. Mainspring 11. Winding spring
6. Pulley
* The Elinvar® brand does not belong to Jaeger-LeCoultre.
Atmos ClAssique - English 1/6
Page 2
Unique in the world.
Atmos, the clock that lives on air.
Temperature variations are its source of power. Its balance
will oscillate as long as the sun shines. Rises in temperature
dilate the gaseous mixture trapped in the expansion chamber
which then compresses the winding spring. In the event of a
fall in temperature, the reverse occurs. The gas contracts and
the spring relaxes. This imperceptible back-and-forth motion
is sufficient to wind the Atmos clock.
No battery, no electrical power, no winding.
Precise and silent.
Precautions for operation and transpor t
The Atmos clock is a very high-precision instrument manufactured with technologies such as only the master-watchmakers
of Jaeger-LeCoultre are capable of handling.The power needed for this clock to operate is extremely low, which means
that your Atmos clock must be placed on a horizontal support that is completely stable (chest of drawers, console, etc.)
to ensure optimum operating conditions. Once it has been
started, the clock must not be moved : the cabinet or suppor t
must be cleaned without handling or moving the clock.
If, however, your clock had to be moved, it is essential to block
the balance.To do so, push the balance blocking lever to the
right up to the thrust stop. Perform this essential blocking
operation when the balance stops,before starting again in the
opposite direction.
For transport, use the complete original packaging.
For the Atmos Classique only :
Tighten the locking screw under the cabinet; as soon as it is
in contact with the balance nut, do an additional one-quarter
turn while blocking it with your hand.
Special instructions for unpacking the
Atmos Classique Transparente clock
1. Open the outer cardboard packing box.
2. Remove the inner cardboard packing box, taking care with
the protective foam.
3. Remove the start-up instructions placed in the lower protective foam.
4. Remove the internal cardboard packing box (brown).
5. Open the Atmos cardboard packing box (bronze).
6. Remove all the thermoformed foam packaging from the
cardboard box, pulling it by the strap. Make sure to hold
the strap firmly fastened and closed.
7. Turn over all the thermoformed foam packaging on a
stable surface, with the base facing upward.
8. Unscrew and withdraw the 2 fixing screws.
9. Gently turn all the thermoformed foam packaging over to
position it on its base.
10. Release and detach the strap.
11. Remove the thermoformed foam packaging on the front
and rear surfaces, sliding them gently aside.
12. Remove the Atmos clock from its base packaging and
place it on a table.
13. Follow the star t-up instructions.
Important : for any dispatch, use the complete original pac‑
kaging. If necessary, ask your dealer to replace the necessary
parts.
Diagram 1
Diagram 2
Protective foam
Internal and external
protective cardboard boxes
User Manual
Internal protective cardboard
box
Front surface packaging
Rear surface packaging
Base packaging with
2 screws and washers
Atmos ClAssique - English 2/6
Page 3
Atmos ClAssique And
A
tmos ClAssique trAnspArente
Operating precautions
The balance of the Atmos Classique clock, which is sus‑
pended from an extremely thin wire, absolutely must be
blocked before any transport, even when it is just moved
slightly (see section on Precautions for operation and trans‑
port), and to perform adjustments.
A
tmos ClAssique
The Atmos Classique clock has two balance locking systems :
- The first, accessible under the cabinet, should be used for
transport.
- The second, accessible after opening the door, is used
when the clock is moved slightly.
Unlock the first locking system by completely loosening the
screw located under the cabinet.
The second system, consisting of a blocking lever, should be
released only after setting the time (see section on Setting
the time).
A
tmos ClAssique trAnspArente
The Atmos Classique Transparente clock has a balance blocking system, which can be accessed after opening the door
and which must be released only after setting the time (see
section on Setting the time).
To star t the Atmos Classique clock, carry out the following
operations.
Ensuring the clock is level
For your Atmos Classique clock to work correctly, its base
should be perfectly horizontal.
To enable you to stabilise it suitably, it has a spirit level. To
ensure correct operation, the bubble must be perfectly centred in the level.
A
tmos ClAssique
The Atmos Classique clock rests on three feet, one of which
is fixed (at the rear) while the other two are adjustable.When
you have placed your clock in its final location, you can easily
perform level setting by screwing up or unscrewing the two
mobile feet.
A
tmos ClAssique trAnspArente
The Atmos Classique Transparente clock rests on three
height-adjustable feet. Level adjustment can be carried out
under each of the feet. When you have placed your clock in
its final location, you can easily perform level setting by unscrewing each of the feet.
Opening the cabinet
Atmos ClAssique
The Atmos Classique clock has a glazed door at the front,
which can be released by pressing the door button downward
and then pulling it slightly toward you. You can remove it by
raising it.
A
tmos ClAssique trAnspArente
The Atmos Classique Transparente clock has a glazed door at
the front, which can be released by pulling the door button,
and is then removed completely when you pull it towards
you.
Do not slant the door too much when it is still in the groove
of the base, so as to avoid damaging the bottom of the glass
pane.
Setting the time
To set your Atmos Classique clock to the right time (and also
for the summer/winter time change), move the minute hand
forward with one finger.
Note : never turn the minute hand in the opposite direction
and never touch the hour hand.
Never perform time setting without first making sure that
the balance is blocked.
Spirit level Height-adjustable feet
Spirit level Height-adjustable feet
Atmos Classique Atmos Classique
Transparente
Step 1 Step 2
Atmos Classique Atmos C lassique Transparente
Atmos ClAssique - English 3/6
Page 4
Starting the clock
Unblock the balance using the blocking lever located at the
front of the clock, under the dial. Lower the lever by pressing
slightly while moving it to the left. Make sure you do not touch
the balance during this operation. Thus released, the balance
begins to oscillate slowly.
If the balance remains motionless :
- Check the level setting.
- Delicately rotate the balance half a turn by hand, then leave
it to resume its own movement by itself.When the balance
is oscillating normally, put the door back in place.
Note : never move an Atmos clock without first blocking
the balance.
Adjusting the gain and loss
Your Atmos Classique clock has been set in the JaegerLeCoultre watchmaking factory located at an altitude of 1000
metres in the heart of the Swiss Jura. If, after about one month’s operation (one month is still needed to ensure that the
balance is completely stabilised), you observe that it is gaining
or losing time slightly, you can correct this using the adjusting
lever which is located at the top of the movement.
The table below shows you by how many graduations the
adjusting lever must be moved depending on the number of
minutes’ time loss or gain on your clock. In accordance with
the information in the table, to correct for time gain, move the
lever to the left towards the «-» sign; to correct for time loss,
move the lever to the right towards the «+» sign.
Once you have started up your Atmos Classique clock, avoid
touching it. It will operate without any intervention by you,
because the Atmos clock simply lives on air.
Gain or loss observed after 1 month
Minutes Correction by moving
per month the adjusting lever by
+ 2,5 min 1/2
+ 5 min 1
+ 7,5 min 1,5
+ 10 min 2
+ 15 min 3
+ 20 min 4
- 2,5 min 1/2
- 5 min 1
- 7,5 min 1,5
- 10 min 2
- 15 min 3
- 20 min 4
graduation(s) to the left
graduation(s) to the right
Gain
Loss
Atmos Classique Atmos C lassique Transparente
Atmos ClAssique - English 4/6
Page 5
This International Guarantee applies to Jaeger‑LeCoultre
products sold or presented for guarantee repairs in all
countries except the United States of America and Canada
(for those two countries, see the Limited Warranty).
The manufacturer’s International Guarantee applies only
to Jaeger-LeCoultre products purchased from authorised
Jaeger-LeCoultre retailers. In addition, all maintenance and
repair works must be carried out either by an authorised
Jaeger-LeCoultre retailer or by an official Jaeger-LeCoultre
Service Centre. If these conditions are not met, the
manufacturer’s guarantee does not apply. For a list of
authorised Jaeger-LeCoultre retailers worldwide, please
contact Jaeger-LeCoultre or its Distributors.
The Jaeger-LeCoultre Atmos clocks
The terms and conditions of the Jaeger-LeCoultre
International Guarantee
The following terms and conditions of the Jaeger-LeCoultre
International Guarantee apply to Atmos clocks sold or
presented for guarantee repairs in all countries except
the United States of America and Canada (for those two
countries, see the Limited Warranty).
Your Jaeger-LeCoultre Atmos clock is guaranteed against
all manufacturing defects for three years from the date of
purchase, subject to the following conditions.
Any part found by our technical services to be defective as a
result of a manufacturing defect will be, at the sole discretion
of Jaeger-LeCoultre, repaired or replaced free of charge.
The Jaeger-LeCoultre International Guarantee is valid only if
the guarantee certificate enclosed with this booklet has been
duly completed, dated, stamped and signed by the authorised
Jaeger-LeCoultre retailer who sold your Atmos clock.
This international guarantee does not cover defects resulting
from accidents, mishandling, incorrect or abusive use (for
example, knocks, dents, crushing, excessive temperatures,
powerful magnetic fields), unauthorised alteration or repair
or the consequences of normal wear and ageing.
The Atmos clock operates without batteries, electricity
or winding. It is accurate and silent but very sensitive, as it
requires only an extremely low amount of energy to operate.
To ensure that your Atmos clock functions properly, you
must place it on an absolutely stable horizontal surface (chest
of drawers, console table, mantelpiece, etc). We advise you
to keep your Atmos clock away from any magnetic fields
(computer, television, etc), as these may interfere with its
functioning.
The Atmos clock must not be moved once it has been
started. Should you have to transport your Atmos clock, do
not forget to lock the balance beforehand (this operation
must be carried out just as the balance stops and before it
starts moving again in the opposite direction).
In order to use your Atmos clock correctly, please refer
carefully to the attached instructions, in particular before
starting the clock or transporting it.
As a consumer, you may have legal rights under applicable
national legislation governing the sale of consumer goods;
those rights are not affected by this guarantee.
Customer service at Jaeger-LeCoultre
The characteristic feature of the Atmos clock is its long
operating life. It functions with virtually no wear and requires
no particular maintenance or lubrication. It may, however,
need cleaning, because of air pollution. Should your Atmos
clock need servicing or repairs, please send it, together with
its guarantee certificate, to the authorised Jaeger-LeCoultre
retailer who sold it to you.
Alternatively, you may send it to one of the official
Jaeger-LeCoultre Service Centres listed at the end of this
booklet, or to any authorised Jaeger-LeCoultre retailer of
which a list is available on the « www. jaeger-lecoultre.com »
website.
Our official Service Centres employ watchmakers trained at
the Jaeger-LeCoultre Manufacture and possess the tools and
parts necessar y to repair and maintain all Jaeger-LeCoultre
watches and clocks.
In certain cases, especially for operations requiring special
tools and parts, the Service Centre will send your Atmos
clock to the Jaeger-LeCoultre Manufacture in Switzerland to
have the necessary work carried out.
In any case or if you live in a country which is not indicated in
our lists, please do not hesitate to contact directly Manufacture
Jaeger-LeCoultre, Switzerland, Rue de la Golisse 8, 1347 Le
Sentier, telephone +41 21 845 02 02, fax +41 21 845 05 50,
which will inform you of the procedure to follow. We also
invite you to visit our website « www. jaeger-lecoultre.com »
for an updated list of official Jaeger-LeCoultre Service Centres.
We will need to keep your Atmos clock for between 6 and
8 weeks, for servicing or repair. This includes the same 5 week
testing and inspection procedure that new Atmos clocks
undergo before they are offered for sale.
International Guarantee
Atmos ClAssique - English 5/6
Page 6
The following Limited Warranty applies to Jaeger‑LeCoultre
products sold or presented for warranty repairs in the
United States of America and Canada only.
The manufacturer’s Limited Warranty applies only to
Jaeger-LeCoultre products purchased from authorised
Jaeger-LeCoultre retailers. In addition, all maintenance and
repair works must be carried out either by an authorised
Jaeger-LeCoultre retailer or by an official Jaeger-LeCoultre
Service Centre. If these conditions are not met, the
manufacturer’s Limited Warranty does not apply. For a list
of authorised Jaeger-LeCoultre retailers worldwide, please
contact Jaeger-LeCoultre or its Distributors.
The Jaeger-LeCoultre Atmos clocks
The terms and conditions of the Jaeger-LeCoultre
Limited Warranty
The following terms and conditions of Jaeger-LeCoultre
Limited Warranty apply only to Atmos clocks sold or
presented for warranty repairs in the United State of America
and Canada.
Your Jaeger-LeCoultre Atmos clock is guaranteed against
all manufacturing defects for three years from the date of
purchase, subject to the following conditions.
Any part found by our technical services to be defective as a
result of a manufacturing defect will be, at the sole discretion
of Jaeger-LeCoultre, repaired or replaced free of charge.
The Jaeger-LeCoultre Limited Warranty is valid only if the
warranty cer tificate enclosed with this booklet has been
duly completed, dated, stamped and signed by the authorised
Jaeger-LeCoultre retailer who sold your Atmos clock.
This Limited Warranty does not cover defects resulting from
accidents, mishandling, incorrect or abusive use (for example,
knocks, dents, crushing, excessive temperatures, powerful
magnetic fields), unauthorised alteration or repair or the
consequences of normal wear and ageing.
The Atmos clock operates without batteries, electricity
or winding. It is accurate and silent but very sensitive, as it
requires only an extremely low amount of energy to operate.
To ensure that your Atmos clock functions properly, you
must place it on an absolutely stable horizontal surface (chest
of drawers, console table, mantelpiece, etc). We advise you
to keep your Atmos clock away from any magnetic fields
(computer, television, etc), as these may interfere with its
functioning.
The Atmos clock must not be moved once it has been
started. Should you have to transport your Atmos clock, do
not forget to lock the balance beforehand (this operation
must be carried out just when the balance stops and before
it starts moving in the opposite direction).
In order to use your Atmos clock correctly, please refer
carefully to the attached instructions, in particular before
starting the clock or transporting it.
Except insofar as prohibited by applicable law, this limited
warranty shall be the exclusive manufacturer warranty.
Neither this limited warranty nor any other warranties,
wether express or implied, including , but not limited to, any
implied warranty of merchantability or of fitness for any
particular purpose, shall extend beyond the period of three
years from the date of purchase.
The liability of Jaeger‑LeCoultre is limited solely and
exclusively to repair or replacement under the terms and
conditions stated herein. Jaeger‑LeCoultre shall not be
liable, by virtue of this limited warranty or otherwise, for
any loss or damage arising out of the use of or inability to
use this Atmos clock nor for any incidental or consequential
damages relating in any way to this clock. Some States,
Provinces and Territories do not allow limitations on how
long an implied warranty lasts, or the exclusion or limitation
of incidental or consequential damages so the above
limitations or exclusions may not apply to you.
This limited warranty grants you specific legal rights, in
addition to which you may have other legal rights which
vary from one Country, State, Province or Territory to
another.
Customer service at Jaeger-LeCoultre
The characteristic feature of the Atmos clock is its long
operating life. It functions with virtually no wear and requires
no particular maintenance or lubrication. It may, however,
need cleaning, because of air pollution. Should your Atmos
clock need servicing or repairs, please send it, together with
its warranty cer tificate, to the authorised Jaeger-LeCoultre
retailer who sold it to you.
Alternatively, you may send it to one of the official JaegerLeCoultre Service Centres listed at the end of this booklet,
or to any authorised Jaeger-LeCoultre retailer of which a list is
available on the « www. jaeger-lecoultre.com » website.
Our official Service Centres employ watchmakers trained at
the Jaeger-LeCoultre Manufacture and possess the tools and
parts necessar y to repair and maintain all Jaeger-LeCoultre
watches and clocks.
In certain cases, especially for operations requiring special
tools and parts, the Service Centres will send your Atmos to
the Jaeger-LeCoultre Manufacture in Switzerland to have the
necessary work carried out.
In any case or if you live in a country which is not indicated in
our lists, please do not hesitate to contact directly Manufacture
Jaeger-LeCoultre, Switzerland, Rue de la Golisse 8, 1347 Le
Sentier, telephone +41 21 845 02 02, fax +41 21 845 05 50,
which will inform you of the procedure to follow. We also
invite you to visit our website « www. jaeger-lecoultre.com »
for an updated list of official Jaeger-LeCoultre Service Centres.
We will need to keep your Atmos clock for between 6 and
8 weeks, for servicing or repair. This includes the same 5 week
testing and inspection procedure that new Atmos clocks
undergo before they are offered for sale.
Limited Warranty
Atmos ClAssique - English 6/6
Loading...