Jademar Lighting Jadipm User Manual
For All JADIPM Series Product
- read these instructions completely and carefullyBefore you begin
JADIPM Architectural Transparent Direct/Indirect
Suspended Single & Continuous Run Series
INSTALLATION INSTRUCTIONS
WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK
•Turn power off before inspection, installation, or
removal.
•Properly ground electrical enclosure.
RISK OF FIRE
•Follow all NEC and local codes.
•Use only UL or IEC approved wire for input/ output
connections. Minimum size 18 AWG (0.82mm
0.0013inch)
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
Each luminaire is to be used with inside driver kit.
Wiring to be performed by a qualified electrician only.
Define Distance Between Canopy Sets
RISQUES DE DÉCHARGES ÉLECTRIQUES
•Coupez l’alimentation avant d’’inspecter, installer ou
déplacer le uminaire.
•Assurez-vous de correctement mettre à la terre le
boîtier d’alimentation électrique.
RISQUES D’INCENDIE
•Respectez tous les codes NEC et codes locaux.
•N’utilisez que des fils approuvés par UL ou IEC pour
les entrées/sorties de connexion. Taille minimum
18 AWG (0.82mm
= 0.0013inch
Example: To install five units in a series, the distance between canopy sets for the 1st (left) and 5th (right) luminaire is 44.8 inches, and the distance between canopy sets for the 2nd, 3rd, and 4th (middle) luminaires is 47.2 inches.
Unit Installation
1.Open the package and check the luminaire and accessories. Wear work gloves to prevent dirt and oil from being transferred to the luminaire.
2. Take off the wire cover plate at INPUT side (FIG.1) and connect AC input cable (FIG.2), then bundle the cable at the bottom.
FIG.1 FIG.2
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468
WWW.JADEMAR.COM
Revised 04/2020
Page 1
JADIPM Architectural Transparent Direct/Indirect
Suspended Single & Continuous Run Series
INSTALLATION MANUAL
Unit Installation (Continued)
3.Plug the female connector of the luminaire input sides onto the male connector of the AC input cable (FIG.3) (Black wire with B, Ground wire
with the middle, and white wire with the last one). Dimming wires connect according to the same wire color.
4.Put the wires into the fixture and lock wire cover.
5. Tighten the suspended kits screw nut with panel screw and connect the top side on the ceiling (FIG.4). Adjust the height of the luminaire
according to your needs (FIG.5).
FIG.3 FIG.4 FIG.5
6. Turn off power.
7.Connect AC input cable (the other side) into J-box. (Black wire with L, while wire with N, Green wire with Ground, Purple wire with dimmer + ,
Gray wire with dimmer).
8.Bundle the AC input cable with suspension wire.
Optional Mounting Method - Connecting Suspended Fixtures In Series
1.For multiple units installed in a series, only the first canopy sets will have an AC Input cable.
2. Combines the two suspension wires and tighten one suspended kits screw nut with panel screw, another one to the next luminarie. Connect
top side on the ceiling (FIG.6).
3.Plug the male connector of the first luminaires input side onto the female connector of the next luminaires input side. Also connect the
dimming wires.
4.Put the wires into luminaires and lock them by the connect plate (FIG.7).
5. Adjust the height according to your requirement.
FIG.6 FIG.7
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468
WWW.JADEMAR.COM
Revised 04/2020
Page 2
Loading...