JACUZZI Stella 6731, Signature 7236, Nova 6042, Elara 6042, Fuzion 7242 Installation Manual
...
OPERATING MANUAL
Pure Air
®
Whirlpool
Salon® Spa
Jacuzzi Luxury Bath
14525 Monte Vista Avenue
Chino, CA 91710
1-800-288-4002
www.jacuzzi.com
LG74000D 06/2019
English
Operating Manual
Table of Contents
General Operation Information. ....................................................................................................................................... 2
Reference Illustration for a Pure Air® System. ................................................................................................................. 3
Pure Air® Operations. ...................................................................................................................................................... 4
Pure Air® Auto-Dri™ Air Channels. .................................................................................................................................. 5
Whirlpool System Reference Illustrations. .................................................................................................................... 6-7
Whirlpool Operations. ................................................................................................................................................... 8-9
Heated Soak Reference Illustrations ........................................................................................................................ 10-11
RapidHeat™. ................................................................................................................................................................. 12
Cleaning. ....................................................................................................................................................................... 13
Maintenance. ............................................................................................................................................................ 13-14
Salon® Spa System Reference Illustrations .................................................................................................................. 15
Salon® Spa Operations. ................................................................................................................................................ 16
Troubleshooting Procedures. ........................................................................................................................................ 17
*For Spanish and French installation instructions, please visit www.jacuzzi.com/baths/support/owners-manuals/.
*Para instrucciones de instalación en español, por favor visite www.jacuzzi.com/baths/support/owners-manuals/.
*Pour directives d'installation en français canadien, veuillez visiter www.jacuzzi.com/baths/support/owners-manuals/.
General Operation Information
All bathtubs manufactured by Jacuzzi Luxury Bath are designed for “ll and drain,” which means the bathtub should be
drained after each use and lled with fresh water by the next bather. This is a health precaution, as these bathtubs are
not designed to hold water continuously like pools or spas.
Close the drain and ll the bathtub until water is at least 1" to 2" (25 mm to 51 mm) above the highest jet or air inlet (see
water line indicated in the illustration - Figure 1). Do not turn on the Whirlpool or Pure Air® system at any time if the jets or
air inlets are not completely immersed in water. Running the Whirlpool or Pure Air® system when there is insufcient water
in the bathtub could result in water spraying outside the bath area.
ATTENTION: When exiting the bathtub, the water level will drop below the jets which could result in water being
sprayed out of the unit. To prevent this, you must turn unit OFF before exiting bathtub.
Page 2 www.jacuzzi.com
Fig. 1
Fill to at least 1" to 2"
above highest jet
Operating Manual
Reference Illustration for a Pure Air® System
These illustrations are for reference only, as the unit comes fully assembled.
DANGER: RISK OF ELECTRIC SHOCK! Before servicing these connections, disconnect all
power supply cables to both 120 VAC services.
J2 Control Panel Pure Air® Schematic Diagram
120 VAC 15A
Fig. 2
CONTROL
PANEL
BLOWER
Dedicated GFCI
Circuit Required
English
J4 Control Panel Pure Air® Schematic Diagram
Fig. 3
120VAC 15A
Dedicated GFCI
Circuit Required
Auto-Dri™
SENSOR
CABLE
BLOWER
CONTROL PANEL
LIGHT CONTROL
CHROMATHERAPY
BOX
Panel
LED Light
LIGHTS 2X
120VAC 15A
Dedicated GFCI
Circuit Required
120 VAC
www.jacuzzi.com Page 3
English
J2 Pure Air® Controls
Fig. 4
Operating Manual
Pure Air® Operations
BLOWER OPERATION
• Press once to turn ON
• Press again to turn OFF
NOTE: The last blower setting used
is remembered by the system and will
automatically resume upon next use.
J4 Pure Air® Controls
Fig. 5
BLOWER OPERATION
• Press to turn ON
• Press again to turn OFF
• Use toggles to control speed
INCREASE TOGGLE
• Press to increase the blower inten-
sity
• Press and hold 5 seconds to set/
cancel daily Auto-Dri™
• Alternately, you can press and hold
the button to increase the intensity
level.
INCREASE TOGGLE
• Press to increase selected
feature
• Press and hold 5 seconds to
set/cancel daily Auto-Dri™
• Press to increase light intensity
• Press to turn ON lights at
last color used from OFF
DECREASE TOGGLE
• Press to decrease the blower intensity
• Alternately, you can press and hold
the button to decrease the intensity
level
NOTE: When switching be-
tween functions, the LED for
the newly selected function
will FLASH once to indicate
selection.
DECREASE TOGGLE
• Press to decrease selected
feature
• Press to decrease light
intensity all the way down
to OFF
CHROMATHERAPY
• Press once to turn lights ON
at white level 2
• Press again to cycle colors
• Press again to stop at the
PULSE FEATURE
• Press to turn Pulse ON
• Press to turn Pulse OFF
• +/- keys can be used to adjust maximum air intensity
current color
• Press again to restart the
cycle
• Color Sequence: White,
Purple, Blue, Turquoise,
STATUS LED
• Relays the current intensity
of selected feature
Green, Yellow, Orange, Red,
Pink, Repeat
Page 4 www.jacuzzi.com
WAVE FEATURE
• Press to turn Wave ON
• Press to turn Wave OFF
• +/- keys can be used to
adjust maximum intensity
Medium
1-2
Low 3-4
Low
High 5-6
High
Medium
7-8
Operating Manual
English
Pure Air® Auto-Dri™ Air Channels
J2 Auto-Dri™ Air Channels
The blower will operate for 20 minutes and then automatically shut off, unless power is manually turned off. In either
case, 20 minutes after the blower has shut off, it will turn ON for a one-minute drying cycle to blow out any water remain-
ing in the air system.
If the bath is used without the blower operating (showering or bathing without using the Pure Air® system), initiate the one-
minute drying cycle manually by use of the ON/OFF switch. Turn the switch ON and OFF again as you exit the bath and
the drying cycle will occur in 20 minutes.
J2 Daily Auto-Dri™ Cycle
To Activate: Holding the button for ve-seconds when the blower is off activates the daily Auto-Dri™ cycle. The blower
will start every day at the same time for one-minute. Once the daily Auto-Dri™ cycle is activated, the blower will come on
for one-second, turn off for two-seconds, come on for one-second and then turn off.
To Deactivate: Holding the button for ve-seconds when the blower is off deactivates the daily Auto-Dri™ cycle. When
the daily Auto-Dri™ cycle is deactivated, the blower will come on for one-second and then turn off.
J4 Auto-Dri™ Air Channels
The Auto-Dri™cycle is automatic and will reduce excessive accumulation of residual water in the air channels.
There are two Auto-Dri™ cycles: drain assisted Auto-Dri™ cycle and daily Auto-Dri™ cycle.
J4 Drain Assist
The Auto-Dri™ cycle is sensor assisted – two sensors (metal dials) are located near the drain of the bathtub. The sensors
detect the presence and absence of water in the bathtub.
To ensure effective and correct operation of the water sensors, it is important to keep them clean and free from block-
age or objects.
After bathing and following the emptying of the bathing well, the sensors detect a “no water” condition. A ve minute wait
time elapses and then the blower is activated. The blower will cycle through a range of speeds for 2 ½ minutes, during
which either 2 or 3 indicator lights will ash at various speeds.
• The Auto-Dri™ cycle will engage even if the blower is not used during bathing.
• The cycle may initiate more than once if the sensors become wet during any part of the Auto-Dri™ operation or during
routine cleaning of the bathtub. This is normal and does not require attention.
•
•
J4 Daily Auto-Dri™ Cycle
Each day, the blower will automatically activate a daily Auto-Dri™ cycle. The blower will operate for one minute on high
power, followed by 15 seconds at ½ power.
To set Auto-Dri™ cycle time: Wait until the time that you desire the daily Auto-Dri™ cycle to activate. With the blower off,
press and hold the plus button for ve seconds. To conrm that you have set the time, the blower will cycle between on
and off two times in a 4 second span.
To cancel daily Auto-Dri™ cycle: With the blower off, press and hold the plus button for ve seconds. To conrm that you
have cancelled the Auto-Dri™ cycle , the blower will come on for 1 second and then stop.
You must set the daily Auto-Dri™ cycle upon installation; the default is no pre-set daily Auto-Dri™ cycle.
If a power failure occurs, the system will default to no daily Auto-Dri™ cycle.
www.jacuzzi.com Page 5
English
Whirlpool System Reference Illustrations
Pushbutton Whirlpool Schematic Diagram
Fig. 6
Operating Manual
J2 Control Panel Whirlpool Schematic Diagram
Fig. 7
120VAC 20A
Dedicated GFCI
Circuit Required
CONTROL PANEL
120VAC 15A
Dedicated GFCI
Circuit Required
FOR MODELS
WITH IN-LINE
HEATER
CONTROL BOX
120 VAC
PUMP
PUMP
PUMP/MOTOR
OR
PUMP/MOTOR
Page 6 www.jacuzzi.com
Operating Manual
CONTROL PANEL
AIR VALVE
ASSEMBLY
CHROMATHERAPY
LIGHTS 2X
LEAD CONNECTIONS
4-WHITE-C
3-BLACK-H
2-N/A
1-GREEN-GRD
VIEW A
LEAD CONNECTIONS
4-WHITE-C
3-BLACK-H
2-RED-L
1-GREEN-GRD
VIEW B
CONTROL BOX
120VAC
Pump
Panel
Blower
LED Light
PUMP/MOTOR
ILLUMATHERAPY
LIGHTS 4X
OR
120VAC 15A
Dedicated GFCI
Circuit Required
120VAC 20A
Dedicated GFCI
Circuit Required
SEE VIEW B
SEE VIEW A
OR
PUMP/MOTOR
Air Valve
FOR MODELS
WITH IN-LINE
HEATER
Whirlpool System Reference Illustrations (Continued)
J2 Control Panel Whirlpool with Chromatherapy Schematic Diagram
English
Fig. 8
CONTROL PANEL
120V 15A
Decidated GFCI
Circuit Breaker
CONTROL BOX
CHROMATHERAPY
LIGHTS
FOR MODELS
WITH IN-LINE
HEATER
PUMP/MOTOR
120V 20A
Decidated GFCI
Circuit Breaker
120VAC
PUMP
J4 Control Panel Whirlpool Schematic Diagram
Fig. 9
www.jacuzzi.com Page 7
English
Operating Manual
Whirlpool Operations
Pushbutton Whirlpool Controls
Fig. 10A
Push down on the button to
turn ON the whirlpool system.
Push down on the button to
turn OFF the whirlpool system.
J2 Whirlpool Controls
Fig. 11
ON/OFF Button
Whirlpool Control
Fig. 10B
In the closed position, the
jets massage with only
water.
In the open position, air
mixes with water to create a
deep, wide plume of
massaging bubbles.
• Press once to turn ON.
• Press again to turn OFF.
OPEN Position
CLOSED Position
J2 Whirlpool Controls with Chromatherapy Controls
Fig. 12
CHROMATHERAPY
• Press once to turn lights ON at
white level 2
• Press again to cycle colors
• Press again to stop at the current color
INCREASE TOGGLE
• Press to increase light intensity
• Press to turn ON lights at last
color used from OFF
NOTE: Default lighting color is
white level 2.
• Press again to restart the cycle
• Color Sequence: White, Purple,
Blue, Turquoise, Green, Yellow,
Orange, Red, Pink, Repeat
Page 8 www.jacuzzi.com
• Press once to turn ON.
• Press again to turn OFF.
DECREASE TOGGLE
• Press to decrease light intensity all the way down to OFF
NOTE: Default lighting color is
white level 2.
Operating Manual
J4 Whirlpool Controls
Fig. 13
English
Whirlpool Operations (Continued)
NOTE: When switching be-
tween functions, the LED for
the newly selected function
will FLASH once to indicate
selection.
WHIRLPOOL
• Press to turn ON
• Press again to turn OFF
• Use toggles to control
speed*
* Whirlpool speed available
only for models equipped
with 2-speed motors.
LEFT AIR VALVE CONTROL
• Press to activate the left air
valve
• Use toggles to control air
mix
CHROMATHERAPY
• Press once to turn lights
ON at white level 2
• Press again to cycle
colors
• Press again to stop at the
current color
• Press again to restart the
cycle
• Color Sequence: White,
Purple, Blue, Turquoise,
Green, Yellow, Orange,
Red, Pink, Repeat
INCREASE TOGGLE
• Press to increase selected
feature
• Press to increase light intensity
• Press to turn ON lights at last
color used from OFF
RIGHT AIR VALVE CONTROL
• Press to activate the right air
valve
• Use toggles to control air mix
STATUS LED
• Relays the current intensity of
selected feature
DECREASE TOGGLE
• Press to decrease the
selected feature
• Press to decrease light
intensity all the way
down to OFF
WAVE FEATURE
• Press to turn Wave ON
• Press to turn Wave OFF
• +/- keys can be used to
adjust maximum intensity
www.jacuzzi.com Page 9
English
CHROMATHERAPY
Heated Soak System Reference Illustrations
J2 Control Panel Heated Soak Schematic Diagram
Fig. 14
CONTROL PANEL
Operating Manual
120VAC 15A
GFCI
PUMP/MOTOR
CONTROL BOX
120 VAC
Pump
J2 Control Panel Heated Soak with Chromatherapy Schematic Diagram
Fig. 15
120VAC 15A
GFCI
Page 10 www.jacuzzi.com
LIGHT
CONTROL PANEL
CONTROL BOX
Panel
LED Light
Pump
PUMP/MOTOR
120 VAC
Operating Manual
Heated Soak System Reference Illustrations (Continued)
J2 Heated Soak Controls
Fig. 16
English
• Press once to turn ON.
• Press again to turn OFF.
J2 Heated Soak with Chromatherapy Controls
Fig. 17
• Press once to turn ON.
• Press again to turn OFF.
CHROMATHERAPY
• Press once to turn lights ON at
white level 2
• Press again to cycle colors
• Press again to stop at the current color
• Press again to restart the cycle
• Color Sequence: White, Purple,
Blue, Turquoise, Green, Yellow,
Orange, Red, Pink, Repeat
www.jacuzzi.com Page 11
INCREASE TOGGLE
• Press to increase light intensity
• Press to turn ON lights at last
color used from OFF
NOTE: Default lighting color is
white level 2.
DECREASE TOGGLE
• Press to decrease light intensity all the way down to OFF
NOTE: Default lighting color is
white level 2.
English
Operating Manual
Whirlpool Operations (Continued)
Controlling Whirlpool Direction & Flow
CAUTION: Never run the whirlpool system with all the jets closed.
To adjust the direction of the jets:
• To change the direction of the water ow, swivel the jet nozzle to the desired angle (Figure 18).
To adjust the water ow to the jets:
• Increase the force of the ow by rotating the nozzle or jet face to the left (counterclockwise). Decrease the force of the
ow by rotating the nozzle or jet face to the right (clockwise). Reference Figure 19.
Fig. 18 Fig. 19
Controlling Waterfall (Applicable Models Only)
Turning ON... Turning OFF...
The waterfall can only be activated when the whirlpool
pump is in operation.
Fig. 20
The more the waterfall control knob is turned in a counter-
clockwise direction, the ow of water will increase. Reference
Figure 20.
Turning the Waterfall Control knob
counter-clockwise will turn on the waterfall
Turning the Waterfall Control knob
clockwise will turn off the waterfall
To remove accumulations of bathtub residue from the system, it is recommended that a bathtub be cleaned at least twice
a month. For best results, however, we recommend that you clean your bathtub after each use using Systems Clean™,
our exclusive two-part plumbing system cleaner made specically for bathtubs. Systems Clean™ is available through an
authorized Jacuzzi Luxury Bath distributor, by calling 1-800-288-4002 or may be purchased online at www.jacuzzi.com.
RapidHeat™
RapidHeat™ (Standard on Salon® Spa Models)
The heater turns ON automatically any time whirlpool operation is active. Heater
operation is not displayed on the control panel. There is a visible indicator light on the
heater itself that signies the heater is operating (Figure 21). The heater will help main-
tain the temperature of the water in the bathtub. It is not intended to heat the water to a
desired temperature.
Fig. 21
Vacuum Switch
OVER HEAT
The heater is equipped with a preset vacuum switch which will not allow
PROTECTION
the heater to turn ON if the pump is not running and water is not owing
through the whirlpool system.
PUSH TO RESET
IMPORTANT NOTE:
Heater will only work when
the water temp is 77°F or
above. You should always fill
the tub with warm water.
High Limit
Reset
HEATER ON
Heater
On
High-Limit Switch
The heater includes an exclusive High-Limit switch (Figure 21). This safety circuit will not false trip from hot tap water. It
will only turn OFF the heater if the thermostat fails. To reset, press the button. If the high-limit trips frequently, please contact us at www.jacuzzi.com, or at 1-800-288-4002.
Page 12 www.jacuzzi.com
Operating Manual
English
Cleaning
Systems Clean™
To remove accumulations of bathtub residue from the whirlpool system, it is recommended that a Whirlpool bathtub be
cleaned at least twice a month. For best results, we recommend that you clean your Whirlpool bathtub after each use using Systems Clean™, our exclusive two-part plumbing system cleaner made specically for Whirlpool bathtubs. Systems
Clean™ is available through an authorized Jacuzzi Luxury Bath distributor by calling us direct at 1-800-288-4002, or may
be purchased online at www.jacuzzi.com/baths.
Bathtub Additives
CAUTION: Do not use oil or oil-based bathtub additives. Never use abrasive or caustic household cleaners on any
Jacuzzi Luxury Bath product.
If you want to use any kind of bathtub additive, use only a small amount of low-foaming powder or crystal substance; the
whirlpool action intensies the foaming properties of soaps.
The use of certain bathtub oils, bubble baths, and bathtub additives may increase the level of accumulations of bathtub
residue in the Whirlpool system and may cause false reading of the water level sensors. If excess accumulations persist,
you should discontinue use of these products.
To remove accumulations of bathtub residue from the Whirlpool system, it is recommended that a bathtub be cleaned
regularly. For best results, we recommend that you clean your Whirlpool bathtub after each use using Systems Clean™,
our exclusive two-part plumbing system cleaner made specically for Whirlpool bathtubs. Systems Clean™ is available
through an authorized Jacuzzi Luxury Bath distributor, or by calling 1-800-288-4002 or may be purchased online at
www.jacuzzi.com.
To clean your bathtub, simply use a mild, non-abrasive liquid detergent solution. You can protect and restore the gloss to a
dulled acrylic surface by applying Meguiar’s #10 Mirror Glaze, a product specically designed for use on acrylic nishes. If
Meguiar’s is not available, use a ne grade automotive rubbing compound followed by an application of clear automotive
paste wax.
Minor scratches which do not penetrate the color nish can be removed by lightly sanding with 600-grit wet/dry sandpaper.
Restore the gloss using Meguiar’s Mirror Glaze or automotive paste wax. Major scratches and gouges which penetrate
the acrylic surface will require renishing. Call Jacuzzi Luxury Bath to nd a service agent in your area.
Maintenance
Spinning Jet Maintenance
If hair, or other types of debris, get caught in the bearings of these jets, it could cause
them to stop spinning (Figure 22). This may require disassembly and removal. To do this,
simply grab the nozzle and pull it straight out of the jet housing. The bearing casing will be
attached to the nozzle. These two items can be separated by holding the casing and push-
ing the nozzle out from the rear of the casing. After the cleaning is complete, reassemble
and reinstall.
Fig. 22
www.jacuzzi.com Page 13
English
Maintenance (Continued)
Whirlpool Suction Cover/Strainer Maintenance
Operating Manual
Clean the suction cover/strainer of hair and debris when necessary (Figure 23).
1. Remove the center screw and detach the suction cover.
2. Clean the cover by back ushing debris from the holes.
3. Replace the suction cover immediately after cleaning.
WARNING! When reinstalling, orient the cover/strainer with the small
notch at the bottom. The gasket must be inserted into the groove of the
cover/strainer before reinstalling onto the suction tting.
Fig. 23
DANGER: RISK OF SEVERE INJURY OR DROWNING! Keep hair a
minimum of 6 inches (152 mm) away from the suction tting at all times when the whirlpool system is operating. Hair
longer than shoulder length should be secured close to the head, or a bathing cap should be worn.
DANGER: RISK OF SEVERE INJURY OR DROWNING! Do not operate the Whirlpool system with the suction
cover/strainer removed! It is a safety device and must always be in place on the suction tting to minimize the potential
hazard of hair and body entrapment.
Page 14 www.jacuzzi.com
Operating Manual
Salon® Spa System Reference Illustrations
J4 Control Panel Salon® Spa Schematic Diagram
Fig. 24
240VAC/20A
Dedicated GFCI
Required
AIR VALVE
ASSEMBLY
CONTROL
PANEL
CONTROL BOX
Air Valve
Blower
FUSE
Panel
HEATER
FUSE/JUNCTION
BOX
FUSE
FUSE
FUSE
PUMP/MOTOR
ILLUMATHERAPY
LIGHTS 4
240VAC
LED Light
Pump
OR
LEAD CONNECTIONS
4-WHITE-C
3-BLACK-H
2-N/A
1-GREEN-GRD
VIEW A
SEE VIEW A
CHROMATHERAPY
LIGHTS 2X
BLOWER
120VAC 15A
Dedicated GFCI
Required
English
AUTO-DRI™
SENSOR CABLES
J5 Control Panel Salon® Spa Schematic Diagram
Fig. 25
240VAC/20A
Dedicated GFCI
Required
AIR VALVE
ASSEMBLY
CONTROL
FUSE/
JUNCTION BOX
FUSE
FUSE
FUSE
PANEL
CONTROL BOX
Air Valve
RS232
Panel
FUSE
Blower
PUMP/MOTOR
Inside
Inside
Ambient
Light 1
Light
Light 1
3
Ambient
Inside
Inside
Light
Light
Light
2
4
2
TEMPERATURE
SENSOR
Temp
Sensor
240VAC
LOGO
Light
Pump
SEE VIEW A
LEAD CONNECTIONS
4-GREEN-(GRD)
4
3-RED-(L)
3
2
2-BLACK-(H)
1
1-WHITE-(C)
VIEW A
CHROMATHERAPY
LIGHTS 2X
120VAC 15A
Dedicated GFCI
Required
HEATER
ILLUMATHERAPY
LIGHTS 4X
OR
BLOWER
AUTO-DRI™ SENSOR CABLES
www.jacuzzi.com Page 15
English
J4 Salon® Spa Controls
Fig. 26
Operating Manual
Salon® Spa Operations
NOTE: When switching be-
tween functions, the LED for
the newly selected function
will FLASH once to indicate
selection.
WHIRLPOOL
• Press to turn ON
• Press again to turn OFF
• Use toggles to control
speed
LEFT AIR VALVE CONTROL
• Press to activate the left air
valve
• Use toggles to control air
mix
CHROMATHERAPY
• Press once to turn lights
ON at white level 2
• Press again to cycle
colors
• Press again to stop at the
current color
• Press again to restart the
cycle
• Color Sequence: White,
Purple, Blue, Turquoise,
Green, Yellow, Orange,
Red, Pink, Repeat
INCREASE TOGGLE
• Press to increase selected
feature
• Press and hold 5 seconds to
set/cancel daily Auto-Dri™
• Press to increase light intensity
• Press to turn ON lights at last
color used from OFF
RIGHT AIR VALVE CONTROL
• Press to activate the right air
valve
• Use toggles to control air mix
STATUS LED
• Relays the current intensity of
selected feature
DECREASE TOGGLE
• Press to decrease the
selected feature
• Press to decrease light
intensity all the way
down to OFF
WAVE FEATURE
• Press to turn Wave ON
• Press to turn Wave OFF
• +/- keys can be used to
adjust maximum intensity.
PURE AIR® FEATURE
• Press to turn ON
• Press again to turn OFF
• Use toggles to control
intensity
Pure Air® and Auto-Dri™ Air Channels
For complete operating instructions reference page 5.
J5 Salon® Spa Controls
Main Menu
POWER
Optional J5 Luxury LCD Control Panel: Operation instructions for this panel are
outlined in the supplemental guide provided in your warranty pack. Refer to this
document for complete operation details (P/N GU47000).
J5 Control Panel
Controlling Whirlpool Direction and Flow
For complete operating instructions reference page 12.
Page 16 www.jacuzzi.com
Operating Manual
Troubleshooting Procedures
PROBLEM PROBABLE CAUSES REMEDY
Pump/motor does not start • No power to pump/motor
• Pump/motor not plugged in
• Pump/motor faulty
Pump/motor operates but no fully
adjustable jets are functioning
Pump/motor operates but air is not
injected into the water
Water leakage from pump unions • Overtightened, O-ring may be pinched or improp-
Pump/motor shuts off by itself before
time elapses
Chromatherapy lights do not operate • Connector has come loose • Contact Jacuzzi Luxury Bath @ 800-288-4002
• Jets are closed
• Suction cover/strainer may be clogged
• Air valves are closed • Open air control valves
erly seated, undertightened
• Motor thermal protection has deactivated pump/
motor due to overheating (supply voltage low)
• GFCI tripped
• Inadequate supply wiring
• Reset GFCI
• Insert plug securely into outlet
• Ensure control panel is connected to control box
• Contact Jacuzzi Luxury Bath @ 800-288-4002
• Open jets by rotating counter-clockwise
• With the motor turned OFF, remove the suction
cover/strainer and remove any debris. Replace the
suction cover before operating
• Loosen unions, check and reseat O-ring. If O-ring
has been pinched out of shape, replace (refer to
number below). When tightening union nuts, hand
tighten only
• Let motor cool; thermal protection will reset. Check
for proper ventilation (check supply voltage)
• Reset GFCI; if it continues to trip, do not use this
unit. Disconnect the unit and have the problem cor-
rected by a licensed electrician before using
• Consult a licensed electrician to correct the wiring
unit
English
Blower does not start • No power to pump/motor
• Blower not connected
• Blower faulty
Blower operates but NO air is exiting
the holes
Blower operates but air is not exiting
all of the holes
Blower shuts off unexpectedly • 20 minute timer has elapsed
Drain assist Auto-Dri™ cycle comes
on multiple times
Drain assist Auto-Dri™ does not
come on 5 minutes after bathtub is
drained out completely
Water not maintaining temperature • High limit switch on heater has tripped • Press Reset button on heater
• Check valves are stuck in the closed position • Contact Jacuzzi Luxury Bath @ 800-288-4002
• Blower intensity is not sufcient
• Obstructed air holes
• GFCI tripped
• Inadequate supply wiring
• Improper ventilation
• Connector has come loose
• Water sensors detect multiple wet and dry conditions
• Water sensors not connected and not detecting
water being drained out of the tub
• Faulty control box
• Reset GFCI and/or breaker
• Ensure plug is fully in outlet
• Ensure control panel is connected to control box
• Ensure control box is connected to control panel
• Contact Jacuzzi Luxury Bath @ 800-288-4002
• Increase the blower intensity. NOTE: The system is
designed such that all air channels operate at the 4th
blower setting.
• Remove debris with a toothpick or tooth brush
• Turn on blower
• Reset GFCI; if it continues to trip, do not use the unit
• Consult a licensed electrician to correct
• Contact Jacuzzi Luxury Bath @ 800-288-4002
• If during a Auto-Dri™ cycle, water is coming in
contact with both sensors, the system is working as
designed and will continue to Auto-Dri™ until excess
water is expelled
• Remove any washcloth or toy that may be covering
the sensors
• Contact Jacuzzi Luxury Bath @ 800-288-4002
Waterfall not working • Whirlpool function not on
• Waterfall control knob is in the OFF position
• Debris in waterfall outlet
• Turn on whirlpool
• Turn waterfall control knob counter-clockwise until
water ow is at the desired ow
• Use a thin, rigid and non-abrasive material (ie. credit
card) and gently swipe back and forth until debris is
cleared away from the waterfall opening
If the unit is within the warranty period, contact Jacuzzi Luxury Bath Service Support at 1-800-288-4002 with your
bath’s serial number before work is started. The serial number is located on the Specication/Serial Number
Plate.
www.jacuzzi.com Page 17
Loading...