™
Affinity
Owner's Manual
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE HYDROMASSAGE BATHTUB
WITHOUT ADULT SUPERVISION.
WARNING : TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE BATHTUB
WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE HYDROMASSAGE BATHTUB UNLESS ALL
SUCTION GUARDS ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT.
WARNING: KEEP BODY AND HAIR A MINIMUM OF 6" AWAY FROM SUCTION FITTING AT ALLTIMES WHEN THE
WHIRLPOOL SYSTEM IS OPERATING. HAIR LONGER THAN SHOULDER LENGTH SHOULD BE SECURED CLOSE TO THE
HEAD.
WARNING:
WARNING: RISK OF ELECTRICAL SHOCK; DO NOT PERMIT ELECTRICAL APPLIANCES (SUCH AS HAIR DRYER, LAMP,
TELEPHONE, RADIO OR TELEVISION) WITHIN 60" (1.5 M) OF THIS HYDROMASSAGE BATHTUB.
WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING
THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID UNCONSCIOUSNESS AND POSSIBLE
DROWNING.
WARNING: RISK OF FETAL INJURY; PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT A PHYSICIAN
BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.
WARNING: RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; DO NOT USE A HYDROMASSAGE BATHTUB
EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.
CAUTION; TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODICALLY IN
ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS.
WARNING: RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; WATER TEMPERATURE IN EXCESS OF 100°F (38° C)
MAY BE INJURIOUS TO YOUR HEALTH. CHECK AND ADJUST WATER TEMPERATURE BEFORE USE.
WARNING: RISK OF HYPERTHERMIA; PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE MEDICAL HISTORY
SHOULD CONSULT A PHYSICIAN BEFORE USING A HYRDOMASSAGE BATHTUB EQUIPPED WITH A HEATER.
AN EQUIPMENT GROUNDING TERMINAL IS PROVIDED IN THE FIELD WIRING COMPARTMENT. TO REDUCE THE RISK
OF ELECTRICAL SHOCK, THIS TERMINAL MUST BE CONNECTED TO THE GROUNDING MEANS PROVIDED IN THE
ELECTRICAL SUPPLY PANEL WITH A CONNECTOR EQUIVALENT IN SIZE TO THE CIRCUIT CONNECTORS SUPPLYING
THIS EQUIPMENT.
NEVER DROP OR INSERT ANY OBJECT INTO ANY OPENING.
PRECAUTIONS
Do not operate the whirlpool system unless the bath is filled with water to at least 2" above the highest jet.
Do not use oil-based bath additives in your whirlpool bath.
When cleaning your bath, do not use abrasive substances which will damage the bath's surface.
To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).
The whirlpool system should be purged at least twice a month. For your convenience, we have developed a plumbing system
cleaner (Systems Clean™) specifically for whirlpool baths. For availability call 1-800-288-4002.
Use this unit only for its intended purpose as described in this manual. Do not use attachments not recommended by the
manufacturer.
This unit must be connected only to a supply circuit that is protected by a ground fault circuit interrupter (GFCI). Such a GFCI
should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI should
interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, there is a ground
current flowing, indicating a possibility of an electric shock. Do not use this unit. Disconnect the unit and have the problem corrected
by a qualified electrician before using.
A pressure wire connector is provided on the exterior of the motor to permit connection of an No. 8 AWG (8.4 mm) solid copper
bonding conductor between this unit and all other electric equipment and exposed metal in the vicinity, as needed to comply with
local requirements.
This unit should be installed by a licensed electrician and grounded.
For built-in and drop-in units, install to permit access for servicing.
Note: This is a professional grade product. A knowledge of construction techniques, plumbing
and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool
Bath products. Our warranty does not cover improper installation related problems.
Contents
Specifications & Rough-in Reference _____________________________________________________ 2
Framing and Support _________________________________________________________________ 3
Wall Cutout & CD/Radio Installation ______________________________________________________ 4-5
TV Installation _______________________________________________________________________ 6
Service Access ______________________________________________________________________ 7
Electrical ___________________________________________________________________________ 7
Drain Information and Plumbing _________________________________________________________ 7
Water Supply________________________________________________________________________ 7
Operation __________________________________________________________________________ 8-11
Maintenance ________________________________________________________________________ 12-13
Template ___________________________________________________________________________ 15
Warranty ___________________________________________________________________________ 17-18
Save These Instructions for Future Use.
Owner's Record
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Number ___________________________
1
DIMENSIONS
68" (1727 mm) L
68" (1727 mm) W
22" ( 559 mm) H1
27" ( 686 mm) H2
35-7/8" ( 911 mm) H3
Specifications & Rough-in Reference
68"
68"
DRAIN/OVERFLOW DIMENSIONS
19" (483 mm) A
12" (305 mm) B
TOTAL WEIGHT/FLOOR LOADING
1500 lb
(682 kg)/
47 lb/sq. ft.
(229 kg/sq. m)
OPERATING
GALLONAGE
120 U.S. gal
(455 liters)
PRODUCT
WEIGHT
250 lb
(114 kg)
ELECTRICAL
REQUIREMENTS
BATH
115 VAC 60 Hz.
30 Amp
Single Phase
(Must be Class A GFCI Protected)
The unit must be hard wired (permanent) from
this circuit to the control box.
H3
H2
34"
H1
DRAIN/OVERFLOW
CUTOUT
16" X 4"
8-3/8"
TOP VIEW
DRAIN/OVERFLOW
24"
48"
FRONT VIEW
A
B
11-7/8"
34"
SENSOR FOR
REMOTE CONTROL
ELECTRICAL
REQUIREMENTS
RAPIDHEAT™ HEATER
115 VAC 60 Hz.
15 Amp
Single Phase
(Must be Class A GFCI Protected)
The unit must be hard wired (permanent) from
this circuit to the control box.
66"
33"
46-5/8"
CUTOUT
2
66"
33"
Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and
fittings necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been
made. Do not lift the bath by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the
finish, do not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the
warranty . Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good
order to the carrier. Refer any claims for damage to the carrier . For definitions of warranty coverage and limitations,
refer to the published warranty information packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to
installation, the bath must be filled with water and operated to check for leaks that may have resulted from
shipping damage or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been
discovered, repaired, or avoided by following this inspection and testing procedure.
Framing and Support
The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor.
The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. Refer
to the table under total weight for your model. The unit must be supported from the bottom of the bath and not
from the bath rim or tile flange. If the subfloor is level, no other preparation is necessary . You can proceed to install
the bath. If the subfloor is not level, you MUST level the entire surface prior to installing the bath. The use of
materials that shim or provide a level installation are allowed provided the method used will insure a level bath that
is supported from the bottom. Materials that may be used are a floor leveling compound, mortar, plaster or minimal
expansion structural foam having a density of a minimum of 5 lbs./cubic ft; however the bath must remain level in
order for it to drain properly and the foam feet must make full contact with the leveling material. Both sides of a joint
or splice of subfloor should be level to each other.
The rim of the bath is not designed to support weight. If finish material is to overlap (maximum 1” overlap) or contact
the bath, the added weight must be fully self-supporting.
The protective film liner inside the bath should be left there to prevent damage to the finish from shoes, tools, etc.
during installation and should not be removed until final cleanup.
SPEAKER
FINISHED
WALL
1" X 4" (NOT FOR SUPPORT)
Typical Installation
WALL
CUTOUTS
WIRES
FOR MODELS WITH TV:
AUDIO CABLES, FAN,
AND TV POWER CORDS
3
Wall Cutout and CD/Radio Installation
The installation requires a cutout in the wall. The cutout allows room for the speakers, CD/Radio speaker/power &
TV audio cable wires.
NOTE: CD/Radio must be must be located a minimum of 5' away from the interior of the bath. The cable provided
with the unit is designed for this minimum distance. If a longer distance is desired, cut the cable and splice to the power
cord with leads provided with the CD/radio. Do not exceed 20' as the CD/radio audio performance will be reduced and
damage to the unit can occur.
Before final setting of the bath, locate the CD/radio speaker & power harness, TV audio cable and CD/Radio grounding wire (CD/Radio chassis to control box bonding bar) coiled under the bath rim. Run wires through wall cutout to
CD/Radio build out.
38"
9" MIN.
CUTOUT IN
WALL (SAME
SIDE AS
MOUNTED
CD/RADIO)
TV AUDIO
CABLE
CUTOUT
5' MINIMUM
MAY BE LOCATED ON
CD/RADIO -
OPPOSITE WALL
FINISHED
WALL
1x4 (NOT
FOR SUPPORT)
To allow clearance for the CD/Radio, build-out section of
wall 7-1/2" from back of stud as shown. We recommend
using 1/2" plywood. A template is provided for sleeve
mounting hole on page 13. Keep CD/Radio build-out
away from insulating materials.
NOTE: CD/Radio has been mechanically fastened to
the bottom of the TV shelf. Remove before installing
unit.
CABLE TV OUTLET
4" MIN.
BATH
PERIMETER
JUNCTION BOX
(POWER TO
CONTROL BOX)
JUNCTION BOX
(FOR HEATER)
Before mounting, press control panel release button and
detach control panel
FINISHED WALL
7-1/2"
4
Remove trim plate. Remove sleeve after disengaging sleeve locks. Stand
the unit and insert the 2 handles between the unit and
sleeve to disengage the sleeve locks. When standing
the unit be careful not to damage the fuse on the rear.
Remove the sleeve. Retain the handles for future use.
Run wires through sleeve. Insert sleeve into build out. When flush, bend appropriate tabs to hold sleeve firmly in
place. Connect the speaker & power connector and TV audio to the CD/radio. Connect the green ground wire to the
CD /radio chassis ground.
Slide Unit into sleeve until locked. Attach trim plate and control panel.
ANTENNA
TV
AUDIO
CABLE
CONTROL
PANEL
GROUND
TERMINAL
FUSE
BUILT OUT
AREA
SPEAKER
& POWER
HARNESS
SLEEVE
CD/RADIO
CHASSIS
TRIM
PLATE
5
TV Installation
Remove back cover by lifting straight upward and then
remove the drip shield. Tighten cable tie and cut off
excess. Tighten cable tie with anchor (not supplied) to
the TV power cord. It is not necessary to attach anchor
to drip shield; the cable tie and anchor are used to
ensure the TV power cord remains in the TV housing.
Locate blackout panel and peel protective backing off
adhesive. Position blackout panel onto TV screen and
press adhesive to TV. Position TV on shelf and hook up
power cord, audio and cable TV cables. Slide TV flush
to front window. Make sure the sensor hole on the
blackout panel aligns with the TV sensor. If they do not
align, adjust the shelf with positioning feet till they are
aligned. Reinstall drip shield. Connect speaker wires to
back cover speakers observing polarity: right speaker
purple + and purple w/black stripe -; left speaker green
+ and green w/black stripe -. Then position back cover
by sliding downward over gasket seal. Make sure
gasket seal did not detach from bath shell (extra gasket
material has been provided). Secure with screws (an
offset screwdriver is provided). An internal fan is provided to cool and ventilate the TV compartment. The fan
will turn on in some instances depending on the thermostat within the TV compartment.
AUDIO
CABLE
DRIP SHIELD WIRING
DRIP SHIELD
FAN
BLACK
RED
TV POWER CORD
TV CONNECTIONS
TO CABLE TV LINE
REAR OF TV
TO STEREO AUDIO
INPUT OF CD/RADIO
CABLE TV
SPEAKER WIRES
POWER, AUDIO AND
CABLE TV/ANT. CABLES
BACK COVER
SCREWS (3)
DRIP SHIELD
VIDEO/AUDIO FROM
EXTERNAL DVD OR VCR
GENTLY PUSH TV AS
FAR FOWARD TO WINDOW
BLACKOUT PANEL
DC INPUT
REMOTE
CONTROL
SENSOR
DOUBLE SIDED TAPE
TOP AND BOTTOM
PEEL PROTECTIVE
BACKING OFF ADHESIVE.
6
Service Access
ELECTRICAL CONNECTION RAPIDHEAT
RAPIDHEAT
TM
JUNCTION BOX
SEPERATE GFCI
PROTECTED CIRCUIT
(TO BATH CONTROL BOX)
SEPERATE GFCI
PROTECTED CIRCUIT
(FOR RAPIDHEAT)
ELECTRICAL CONNECTIONS
RAPIDHEAT
CONTROL BOX
JUNCTION BOX
FROM
POWER
SUPPLY
BLACK
WHITE
GROUND
(GREEN)
TO
RAPIDHEAT
WIRE NUTS
For partially or fully sunken installations, allow for access to service connections. It is the installer's responsibility to provide sufficient service access. See Service Access illustration. Provide adequate ventilation
(minimum 30 square inch opening) for cooling the motor and to supply sufficient air for the jets.
SERVICE ACCESS
Bonding
Connect a #8 guage (10mm2) minimum solid copper
bond wire from the house electrical pannel or an approved local ground to all metal components (i.e. junction box etc.). An approved ground may be an 8 foot long
ground rod (3 meter long earth rod), a plate electrode or
other acceptable bond location. Check your local building code for requirements.
BLOWER
ACCESS
Electrical Connections
Two separate circuits are required for this unit:
Bath
Install a 1 15 V AC 30 AMP dedicated circuit protected by
a Ground Fault Circuit Interrupter (GFCI). The unit must
be hard wired (permanent) from this circuit to the control box. Remove cover of control box and hard wire
from GFCI circuit to terminal block.
DANGER: RISK OF ELECTRIC SHOCK. Connect only
to a circuit protected by a Ground Fault Circuit
Interrupter.
Rapid Heat
Install a 120 VAC 15 AMP dedicated circuit with GFCI
protection. The unit must be hard wired (permanent)
from this circuit to the junction box for the heater (see
below). For operation, refer to the RapidHeat instructions.
DANGER: RISK OF ELECTRIC SHOCK. Connect only
to a circuit protected by a Ground Fault Circuit
Interrupter.
We recommend that a qualified electrician perform this
work.
CAUTION: Operating the motor/pump without
enough water in the bath can cause leaking and permanent damage to the pump. Before power is applied to the installation, make sure the switch is in
the OFF position to avoid pump damage.
MOTOR/PUMP
ACCESS
CONTROL BOX
7
Drain Information
2"
FILL TO AT LEAST 2"
ABOVE HIGHEST JET
A drain/overflow assembly must be installed on the bath,
water tested, and connected to the sanitary system of
the house. After opening the carton, inspect for damage and verify that the kit is of the proper finish. In the
Jacuzzi Whirlpool Bath drain/overflow kit, note that the
waste flange, strainer, overflow cover and cover screws
are packaged in a separate package within the kit to
protect the trim finish. Follow the installation instructions provided with the drain/overflow kit.
After the drain is fully installed, test for proper drainage.
If the unit does not drain properly, rectify this condition
before proceeding with the installation. Jacuzzi Whirlpool bath is not responsible for removal and/or reinstallation costs.
NOTE: Watertight installation of the drain is the installer's responsibility. Drain leakage is excluded
from the Jacuzzi Whirlpool Bath warranty of this
product.
Plumbing
Pump, jets, and suction fittings for the whirlpool system
are factory plumbed in schedule 40 PVC piping. All
Jacuzzi Whirlpool Bath products are factory tested for
proper operation and watertight connections prior to
shipping.
Before securing the bath to the floor a test for possible
water leaks must be made. Fill the bath and check for
leaks. If leaks are detected, notify your Jacuzzi Whirlpool Bath Dealer. Do not install the unit.
Water Supply
Consult local authorities for plumbing code requirements
in your area.
IMPORT ANT : Proper installation of the fill spout plumbing and compliance with local codes are the responsibility of the installer. Jacuzzi Whirlpool Bath does not
warrant connections of water supply fittings and piping,
fill systems, or drain/overflow systems. Nor is it responsible for damage to the bath which occurs during installation.
CAUTION: A nonflammable protective barrier must be
placed between soldering work and bath unit to prevent
damage to the bath.
Clean-Up After Installation
To avoid dulling and scratching the surface of the bath,
never use abrasive cleaners. A mild liquid detergent
and warm water will clean soiled surfaces.
Remove spilled plaster with a wood or plastic edge.
Metal tools will scratch the surface. Spots left by plaster or grout can be removed if lightly rubbed with detergent on a damp cloth or sponge.
Paint, tar, or other difficult stains can be removed with
paint thinner, turpentine, or isopropyl alcohol (rubbing
alcohol).
Minor scratches which do not penetrate the color finish
can be removed by lightly sanding with 600-grit wet/dry
sandpaper. You can restore the glossy finish to the
acrylic surface of the bath with a special compound,
Meguiar's #10 Mirror Glaze. If that is not available, use
automotive rubbing compound followed by an application of automotive paste wax.
Major scratches and gouges which penetrate the acrylic
surface will require refinishing. Ask your Jacuzzi Whirlpool Bath dealer for special instructions.
OPERATION
Water Level
Close the drain and fill the bath until water is at least 2"
above the highest jet (see water line indicated in the
illustration). Do not turn on the whirlpool system at
any time if the jets are not completely immersed in
water. Running the whirlpool system when there is in-
sufficient water in the bath could result in water spraying outside the bath area. Running the whirlpool system without water will damage the recirculating pump.
8
Remote Control
POWER
TV MODE
VOLUME UP & DOWN
CD/DVD FUNCTION
BLOWER FUNCTION
The Floating Remote Control is a universal remote control that has been programmed to operate the TV. If the
remote has been deprogrammed the following procedure will reprogram the remote:
For TV
1. Press and release the TV button.
2. Press and hold the BLOWER button. The LED will flash.
3. While holding the BLOWER button, press the POWER button for 2 seconds until the LED lights up. Then
release both buttons.
4. Enter the 5 digit code 12343 using the VOLUME up and down and CHANNEL up and down: Volume up = 1,
Volume down = 2, Channel up = 3 and Channel down = 4.
5. The LED will shut off if the code is accurate and the setting successful. If not, the LED will flash twice and the
procedure must be repeated starting from step 1.
For Bath
1. Press and release the Bath button.
LED INDICA TOR
BA TH MODE
CHANNEL UP & DOWN
JETS FUNCTION
LIGHT FUNCTION
2. Press and hold the BLOWER button. The LED will flash.
3. While holding the BLOWER button, press the POWER button for 2 seconds until the LED lights up. Then
release both buttons.
4. Enter the 5 digit code 24332 using the VOLUME up and down and CHANNEL up and down: Volume up = 1,
Volume down = 2, Channel up = 3 and Channel down = 4.
5. The LED will shut off if the code is accurate and the setting successful. If not, the LED will flash twice and the
procedure must be repeated starting from step 1.
ACTIVATING THE WHIRLPOOL BATH (aim remote at sensor on bath)
1. Pressing the BATH button allows access to the JETS , LIGHT BLOWER functions.
2. Press the LIGHT button once to activate the lights; press again to deactivate.
3. Press the JETS button once to activate the jets; press again to deactivate.
4. Press the BLOWER button once to activate the blower; press again to deactivate.
NOTE: Jets, light and blower will automatically turn off after 30 minutes.
9
PURGES
Automatic Purge
With all functions off either, manually or by program, a
60 minute timer will be initiated. Once this timer is finished, a 1 minute purge will be activated (blower) to
purge any remaining water in the air channel. If any
key is pressed the purge timer will be reset.
TV
The Floating Remote will control the volume and change
the channels of the TV.
For complete operation of the TV consult the manual
enclosed.
Note: The TV manufacturer’s remote is not intended to
be used in the bath.
Daily Purge
If the user holds the button on the bath control on the
unit for 5 seconds, the program will initiate a 1 minute
purge (start the blower) and will purge every day at the
same time for 1 minute. To cancel the daily purge option simply hold the button for 5 seconds. The daily
purge will not activate if one of the accessaries is on,
but it will have priority on the Automatic purge. This
means that if the program is waiting to Automatic purge
and a Daily purge crosses that time, then the automatic
purge will be cancelled and the daily purge will be
initiated.
BATH CONTROL
CD/DVD FUNCTION (VIDEO INPUTS TO TV)
1. Press TV button, then POWER Button. This will turn
the TV ON.
2. Press CD/DVD to select the applicable input source.
The on-screen display will show VIDEO 1 or VIDEO
2 for any external video components or TV mode.
REMOTE BATTERY REPLACEMENT
The remote is powered by 2 AAA size batteries. To
change the batteries, unscrew and remove the rear
cover. Remove the old batteries and load the new ones
with their polarities (+ and –) aligned properly . Replace
the cover making sure the water proof gasket (screws
and control) is in the proper position.
After the batteries have been replaced, the LED will flash
twice to indicate that the programmed codes are still
memorized. The LED will flash 3 times to indicate the
programmed codes have been erased and will have to
be reprogrammed. You have 3 minutes to change the
batteries before the codes will be erased.
NOTE: Batteries installed with incorrect polarity may
leak and damage the remote control. Do not mix old
and new batteries or carbon types with alkaline types.
BATTERIES (2 AAA)
CD PLAYER/AM/FM SYSTEM
Power On
The CD player and AM/FM system must be activated
from the manufacturers remote control for the CD unit
or manually from the CD player panel. The floating remote does not control CD/AM/FM functions.
AUX-IN Setup
In order to hear the TV audio, CD Player/AM/FM System must be set to AUX-In mode. To perform this setting, follow the instructions of the CD Receiver manual
under AUX IN Mode. If power to the unit is interrupted,
the CD Receiver will have to be reset.
For complete operation of the CD/AM/FM unit consult
the manual enclosed.
Note: The manufacturers remote for the CD/AM/FM unit
is not intended to be used in the bath.
Note: The quality of AM reception will vary by locality.
Jacuzzi Whirlpool Bath is not responsible for the quality
of AM reception.
REAR SIDE
COVER
COVER REMOVED
SUGGESTED LOCATION FOR REMOTE HOLDER
Apply a dab of clear silicone adhesive to the underside of holder and attach where convenient in area
shown.
AREA TO LOCATE
REMOTE HOLDER
10
Controlling Whirlpool Action
The whirlpool action in your bath is influenced by three
factors – direction of flow, force of water, and force of
air.
Direction: To change the direction of the water flow,
swivel the jet nozzle to the desired angle. The jets can
be directed individually toward any location on your body
to provide a hydromassage. The jets can also be adjusted so that they all point in the same direction (clockwise or counterclockwise) to circulate the water in a circular motion around the bath, causing a total whirlpool
effect.
Water Force: The high volume, fully adjustable jets
can be adjusted to control the force of the water coming
into the bath. For robust action, increase the force of
the flow by rotating the jet handles to the left (counterclockwise). For a more gentle effect, rotate the handles
to the right (clockwise). Never run the whirlpool sys-
tem with all the jets closed.
Force of Air: Four knobs located on the bath serve as
controls for the air induction system. The intensity of
the hydromassage whirlpool action is determined by the
amount of air inducted into the water. As the amount of
air is increased, the hydromassage action increases.
For maximum air induction, rotate the control knobs fully
counterclockwise to the largest circles. For fewer air
bubbles, decrease the amount of air induction by rotating the control knob clockwise. When the knobs are
turned to the smallest circles, only water is being
circulated.
AIR INDUCTION CONTROLS
TURN CLOCKWISE TO
REDUCE AIR FLOW
TURN COUNTER-CLOCKWISE
TO INCREASE AI R FLOW
CD/Radio
For operation of the CD/radio consult the manual enclosed.
Note: The remote for the CD/radio is not intended to
be used inside the bath.
Note: For units with AM/FM radios, the quality of AM
reception will vary by locality. Jacuzzi Whirlpool Bath is
not responsible for the quality of AM reception.
TV
For operation of the TV consult the manual enclosed.
NOTE: In order to hear the TV audio, the Pioneer CD
Receiver AUX function must be setup to be ON.
To perform this setting:
• If the unit is on, press SOURCE and hold until the
unit turns off.
• Press FUNCTION repeatedly until AUX appears in
he display
• Select AUX on and of f with . The status will be
displayed: AUX :ON
If power to the unit is interrupted, the CD Receiver will
have to be reset.
Note: The remote for the TV is not intended to be
used inside the bath.
RapidHeat
Once the heater is installed and the whirlpool pump is
operating, the heating function is totally automatic. The
heater will help maintain the temperature of the water in
the bath.
Vacuum Switch
The heater is equipped with a preset vacuum switch
which will not allow the heater to turn ON if the pump is
not running with water flowing through the whirlpool
system.
High-Limit Switch
The heater includes an exclusive High-Limit switch. This
safety circuit will not false trip from hot tap water. It will
only turn off the heater if the thermostat fails. To reset,
press the button. If the high-limit trips frequently, contact your dealer.
JETS
DIRECTIONALLY
ADJUSTABLE
FULLY
ADJUSTABLE
11
HIGH LIMIT RESET
OVER HEAT
PROTECTION
PUSH TO RESET
BATH MAINTENANCE
Cleaning the Bath
To clean your bath, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the
gloss to a dulled acrylic surface by applying Meguiar's
#10 Mirror Glaze, a product specifically designed for
use on acrylic finishes. If Meguiar's is not available, an
acrylic polish of equal quality or automotive paste wax
is acceptable. Never use abrasive household clean-
ers on any Jacuzzi Whirlpool Bath product.
Repairs to the Surface
Minor scratches which do not penetrate the color finish
can be removed by lightly sanding with 600-grit wet/dry
sandpaper. Restore the gloss using Meguiar's Mirror
Glaze or automotive paste wax.
Major scratches and gouges which penetrate the acrylic
surface will require refinishing. Ask your Jacuzzi Whirlpool Bath dealer for special instructions.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE
PURGED AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the
whirlpool system, it is recommended that a whirlpool
bath be purged at least twice a month. For best results,
however, we recommend that you purge your whirlpool
bath after each use using our exclusive two-part plumbing system cleaner made specifically for whirlpool
baths. Systems Clean ™ is available through an authorized Jacuzzi Whirlpool Bath Distributor or by calling us
direct at 1-800-288-4002. Instructions for use: Immediately after bathing and exiting the whirlpool bath, leave
the bath water in the tub and add hot water, if necessary,
so the water is at least 2" above the highest jet. Turn on
the unit without the aerator. Pour the contents of the
Systems Clean Packet 1 (taking care not to get the
material on yourself) into the bath near the intake for the
circulation pump. Repeat same process with Systems
Clean Packet 2. It is important to use Packet 1 before
Packet 2 to avoid a strong odor. Run the bath for 5 to
10 minutes. Drain completely and rinse any residue.
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH
ADDITIVES.
If you want to use any kind of bath additive, use only a
small amount of low-foaming powder or crystal substance; the whirlpool action intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath
additives may increase the level of accumulations of
bath residue in the whirlpool system. If excess accumulations persist, you should discontinue use of these
products.
Spinning Neck Jets
If hair or other kind of debris gets caught in the bearings
of these jets, it could cause them to stop spinning. This
may require disassembly and cleaning. To do this,
simply grab the nozzle and pull straight out of the jet
housing. The roller bearing casing will be attached to the
nozzle. These can be separated by holding the casing
and pushing the nozzle out from the rear of the casing.
After cleaning, reassemble in reverse.
PUSH FROM
REAR TO
REMOVE NOZZLE
NOZZLE
ROLLER BEARING CASING
If you have followed the standard purging instructions
above and still have an excess accumulation of bath
residue and desire an alternative cleaning mechanism,
we recommend SUPER SYSTEMS CLEAN PLUS manufactured by Stearns Packaging to rectify this condition.
This may be obtained by contacting us at l-800-288-
4002. It is recommended that you follow the instructions
provided by the manufacturer with the product. Repeated use may be necessary. SUPER SYSTEMS
CLEAN PLUS does not replace the necessity to regularly purge your whirlpool system with Systems Clean as
recommended.
(For additional information about water content, contact
us for a copy of the Jacuzzi Water Quality Primer.)
12
Suction Cover/Strainer Maintenance
Clean the suction cover/strainer of hair and debris when
necessary. To do this, remove the center screw and
detach the square cover. Clean the cover by backflushing debris from the holes. Replace the suction cover
immediately after cleaning. When reinstalling, orient
the cover/strainer with the small notch at the bottom.
The gasket must be inserted into the groove of the cover/
strainer before reinstalling onto the suction fitting.
CAUTION: Keep hair a minimum of 6 inches away
from the suction fitting at all times when the whirlpool system is operating. Hair longer than shoulder length should be secured close to the head. Do
not operate the whirlpool system with the suction
cover removed! It is a safety device and must always be in place on the suction fitting to minimize
the potential hazard of hair and body entrapment.
Lamp
When the bulb burns out, replace it from the back of
the lamp fitting, on the underside of the shell, by pulling
out the bulb receptacle. Replacement bulbs (7W, 12V)
are available from your Jacuzzi Whirlpool Bath dealer.
LIGHT BULB REPLACEMENT
LOCKING NUT
LIGHT BULB
SUCTION COVER/STRAINER ASSEMBLY
COVER STRAINER
SCREW
NOTCH
GASKET
BULB RECEPTACLE
LIGHT BEZEL
SHELL
SUCTION
FITTING
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type.
It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of this product. Jacuzzi Whirlpool
Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath
P.O. Box 702168, Dallas, TX 75370-2168
Service Support: Call (800) 288-4002
©2000 Jacuzzi Whirlpool Bath S198000 8/16/04
Printed on Recycled Paper
13
Printed in the U.S.A.
14
182 mm
53 mm
TEMPLATE FOR CD/RADIO MOUNTING SLEEVE
15
Jacuzzi Whirlpool Bath Limited Warranty
Designer Collection Bath Product
Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer
Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the
unit or its equipment in accordance with the following terms and conditions.
TWO YEAR LIMITED WARRANTY ON BATHS
Our limited warranty on Designer Collection Bath products is for two (2) years. Our warranty covers the unit and factory-installed components (e.g.,
pump, motor) against defects in material or workmanship. Warranty coverage begins on the date the unit was originally purchased by the user.
FIVE YEAR (PARTS ONLY) LIMITED WARRANTY ON PUMP AND MOTOR
Our limited warranty on the pump and motor is for five (5) years for parts only. Warranty coverage begins on the date the unit was originally purchased by the
user.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
Our limited warranty on options and accessories manufactured by the Company is for ninety (90) days for parts only. Our warranty covers options and
accessories manufactured by the Company (e.g., fill spout kits, trim kits, skirts) against defects of material or workmanship. Warranty coverage begins on the
date the option or accessory was originally purchased by the user.
Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other person, or resulting from, without
limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.); modification of any type for any reason (including modification
to meet local codes); improper installation (including installation not in accordance with instructions and specifications provided with the unit); connections
supplied by the installer of the equipment; improper voltage supply or unauthorized electrical modification; misuse; incorrect operation, or lack of proper routine
maintenance; operation of the unit without specified minimum amount of water or at inappropriate water temperature; use of abrasive or improper cleaners; or
acts of God, such as lightning, floods, earthquakes, etc.
In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause
(e.g., water damage to carpet, ceiling, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts when pool and/or spa
chemicals are used in the unit; optional bath equipment not manufactured by the Company but supplied by Dealer, installer or the Company; the unit's prior usage
as an operational display; or defects that should have been discovered before installation. This limited warranty does not include: labor, transportation, or other
costs incurred in the removal and/or reinstallation of the original unit and/or installation of a replacement unit; any costs relating to obtaining access for repair;
or loss of use damage, including loss of sales, profit or business advantage of any kind under any circumstances. Bath units are excluded from any warranty coverage
if any addition, deletion, or modification of any kind whatsoever has been made to the unit (or to any component).
Warranty coverage is provided in the United States of America only.
EXCLUSION OF IMPLIED WARRANTIES
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO
THE FULL EXTENT ALLOWED BY LAW.
NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable
to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not be responsible for
any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature or specifications furnished
by the Company.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above
limitations and exclusions may not apply to you.
The attached Warranty Registration Card MUST be filled out by the purchaser within thirty (30) days from purchase and mailed to Jacuzzi Whirlpool Bath
in order for this warranty to become effective.
WARRANTY COVERAGE
WARRANTY LIMITATIONS
RETURN OF WARRANTY CARD
Jacuzzi Whirlpool Bath
P.O. Box 702168
Dallas, TX 75370-2168
RESPONSIBILITIES OF OTHERS
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring
the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of
a problem, the unit must not be installed. The Company is not responsible for failures or damage that could have been discovered, repaired, or avoided by proper
inspection and testing prior to installation.
Damage occurring in transit is the responsibility of the carrier. The user or installer MUST open the crate and inspect the unit for damage when it is delivered.
If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure of the carrier to respond should
be reported to the seller and the carrier. Your freight claims should be filed promptly thereafter.
It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs relating to
obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.
Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the
responsibility of the user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (Options and accessories manufactured by the Company are
warranted for ninety (90) days from the original date of purchase for parts only.)
The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these requirements at the
time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state building codes.
WARRANTY SERVICE
For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such firms are not agents
or representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered
by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the
problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure
occurred or was discovered within the warranty period; an authorized independent service person or Company representative has been permitted to inspect the
unit during regular business hours within a reasonable time after the problem was reported by the user.
In order to obtain warranty service, consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service Agent. Describe
the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service.
If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:
Jacuzzi Whirlpool Bath
Warranty Service Department
P.O. Box 702168
Dallas, TX 75370-2168
Call: (800) 288-4002
To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied by the Company,
call or write the above. Provide a description of the problem and proof of purchase. You will be instructed how to obtain replacements and where to return, at
your expense, the failed component(s), option(s), or accessory(ies).
All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender terminates the
Company's warranty obligation.
©2000 Jacuzzi Whirlpool Bath S198000 8/16/04
Limited Warranty
Accessory(ies)
Ninety-Day
Parts Only
On
Limited Warranty
Accessory(ies)
Ninety-Day
Parts Only
10.Approximately how long have you lived in this home? ___________
12.Was your purchase process?
13.How technically aware were you of the patented Jacuzzi® jet system
( ) $40,000 to $49,999 ( ) $150,000 and Above
( ) Very easy ( ) Easy ( ) Difficult ( ) Very Difficult
prior to your purchase?
( ) Not aware ( ) Somewhat aware ( ) Very aware
11.Please indicate, approximately, the total annual income of your
( ) 1 month-2 months
household.
( ) Up to $24,999 ( ) $50,000 to $74,999
( ) $25,000 to $29,999 ( ) $75,000 to $99,999
( ) $30,000 to $39,999 ( ) $100,000 to $149,999
9. How long did you shop before purchasing unit?
Please estimate $ _______________________________________
( ) Eljer ( ) Lasco ( ) Price Pfister ( ) Aqua Glass
( ) Kohler ( ) American Standard ( ) Sterling
( ) Other (Specify) _____________________________________
( ) 1 day ( ) 2 months-6 months
( ) 2-7 days ( ) 6 months-1year
( ) 1 week-2 weeks ( ) 1 year-2 years
( ) 2 weeks-4 weeks ( ) +2 years
6. What is the current market value of this property?
7. What is the age of the head of the household? _____________ years
8. What other manufacturers did you consider?
4. Who finally decided which product you would buy?
5. Who installed? ( ) Already installed/New Home
( ) Self ( ) Spouse ( ) Self and Spouse Together
( ) Other Family Member ( ) Designer/Architect
( ) Builder/Plumber/Remodeler ( ) Already Installed
( ) Contractor/Plumber when remodeling
( ) Self/Spouse when remodeling
( ) Other _____________________________________________
3. What was the main reason for purchase?
( ) Styling ( ) Warranty Service ( ) Product Features
( ) Brand Name ( ) Price ( ) Hydrotherapy
( ) Home Resale _______________________________________
( ) Other _____________________________________________
2. Who first gave you specific information about this product (specifications,
( ) Word of Mouth . . . Friend/Relative/Acquaintance
( ) Other (Please Describe)_______________________________
prices, etc.)?
( ) Dealer/Plumbing Supplier ( ) Builder ( ) Remodeler
( ) Plumbing Contractor ( ) Retailer/Home Center Store
( ) Decorator/Architect ( ) Already Installed
1. How did you first hear about this Jacuzzi® product?
( ) Advertisement ( ) Article in Magazine/Newspaper
( ) Visited Dealer/Plumbing Supplier ( ) Yellow Pages
( ) Builder/Plumber/Remodeler ( ) Decorator/Architect
( ) Visited Retailer/Home Center Store
Model Name _____________________________________________
Serial Number ___________________________________________
Dealer's Name ___________________________________________
Dealer's Address__________________________________________
On
This card must be filled out and returned to the address printed on the other
side within thirty (30) days from date of purchase in order for this warranty to
be come effective.
Purchaser's Name ________________________________________
Purchaser's Address _______________________________________
City _____________________________ State _____ Zip________
Date of Purchase _________________________________________
Jacuzzi Whirlpool Bath
S198000
8/16/04
Warranty
Registration Card
Loading...