Jacuzzi Plumbing Product User Manual
Neo Angle Shower System
WITHOUT BODY SPRAY OR
WITH BODY SPRAY
INSTALLATION INSTRUCTIONS
BASIC COMPONENTS
• Neo Shower Base
Back Wall
Seat Wall (LH or RH)
Shelf Wall (LH or RH) with accessory bracket
(purchased separately, chrome or brass)
OR
• Neo Shower Base
Body Spray Wall
2 Shelf Walls with accessory brackets
(purchased separately, chrome or brass)
BACK WALL
SHELF WALL
*
DIGITAL
CONTROLLER
ACCESSORY
BRACKET
*OPTIONAL FEATURES
™
• Optica
• Optica
• 6-Port Showerhead
• Dome (clear)
• SteamPro™Steam Generator
• Digital Controller for SteamPro
• Steam/Shower Door
BODY SPRAY WALL
OR
Wall Mount Shower Set
™
300 Shower Mixer Valve
™
DOME (CLEAR)
*
SHOWER
HEAD
*
OPTICA
WALL MOUNT
SHOWER SET
*
OPTICA 300
SHOWER
MIXER VALVE
ACCESSORY
BRACKET
*
STEAM HEAD
& STEAM SHIELD
NOTE: The body spray jets require a minimum operating water pressure of 30 psi.
Illustration shown here features a right hand seat wall unit with all options.
Use installation instructions provided with product. Product specifications are subject to change without notice.
NEO
SHOWER
BASE
SEAT WALL
INSTALLATION INSTRUCTIONS
Important: Read complete instructions before beginning installation.
Review instructions for all optional items being considered for installation before completing rough-in. The
successful installation of the options may require some modifications to be made to the custom shower system
or the rough-in structure before completion.
Check for shipping damage upon receipt of the custom shower system. Jacuzzi Whirlpool Bath is not responsible for
damage sustained during shipping. If damage is evident before unpacking, see instructions regarding shipping claims
on the outside of the carton and immediately file a claim with the carrier.
Once the components have been removed from the carton and before it is permanently installed, check the parts
completely for damage resulting from shipping or handling. All Jacuzzi Whirlpool Bath products are factory tested for fit
and finish prior to shipping. If problems are detected, immediately notify your Jacuzzi Whirlpool Bath dealer or Authorized
Service Agent, or call Jacuzzi Whirlpool Bath, (800) 288-4002, for Warranty Service.
NOTE: Damage or defects which could have been discovered and repaired prior to installation and which are
claimed after final installation of the shower system are excluded from our warranty.
STEP 1. ROUGH-IN FRAMING DETAILS
ROUGH-IN DIMENSION CHART
MODEL A B C D E F
4242N 42-1/8" 42-1/8" 16" 16" 27" 12-3/8"
4848N 48-1/2" 48-1/8" 16" 16" 32-1/4" 16-3/8"
A
E
A
E
D
C
L
C
L
F
C
E
B
C
L
D
F
C
C
L
CROSS
SUPPORT
E
B
SHOWN WITH 2 SHELF WALLS
SHOWN AS A RIGHT HAND SEAT W ALL
STEP 2. ROUGH-IN PLUMBING
A. Install water lines and rough plumbing. Valve should
be located between 36" and 48" from the floor. Use
blocking and secure with pipe straps.
B. If stationary shower is used, install shower riser.
Suggested shower head location is 78" from the floor
(above the endwall).
C. The locations of the valves, mixers, and shower head
should be determined before the walls are placed in
position. Where access to connections is limited, allow
enough flexibility in the supply lines for easier positioning of the valves after the unit is in place.
From stable reference points such as subfloor and
front of the double studs, measure and note the
locations of the valves, shower head arm and connection for body spray jets.
STEP 3
Install Shower Base per Shower Base Instructions.
A. For proper fit and installation of the custom shower
system it is imperative that the shower base is
level on all sides and the wall structure is plumb.
ROUGH-IN PLUMBING DETAILS
BLOCKING
SHOWER HEAD
TO BODY SPRAY
JETS WALL
(IF NEO WALL IS
EQUIPPED
WITH JETS)
OPTICA 300
MIXER AND
TRANSFER
TO
VALVE
12" CLEARANCE
FOR PLUMBING
AT SEATWALL
CENTERLINE
SUPPLY LINES
78"
(FOR FIXED
SHOWER
HEAD)
36" MIN.
48" MAX.
24"
NOTE: Watertight installation of the drain is the installer’s
responsibility. Drain leakage is excluded from the Jacuzzi
Whirlpool Bath warranty of this product. (See “Drain
Installation Instructions” provided with drain.)
SUGGESTED PLUMBING LAYOUT
(REVERSE FOR LEFT HAND SEAT WALL VERSION)
LINE TO WALL
BAR SHOWER
HEAD OR
SHOWER
HEAD
LINE TO BODY
SPRAY JETS
WALL (IF BACK
WALL IS
EQUIPPED
WITH JETS)
OPTICA 300 CONNECTIONS
TO SHOWER HEAD OR HAND HELD SHOWER
MxF ADAPTER (3)
COPPER GASKET (4)
TRANSFER
VALVE
TO BODY
SPRAY W ALL
LEFT-HAND
THREAD TO
SWEAT ADAPTER
OPTICA 300
MIXER/
TRANSFER
VALVE
HOT
WATER
SUPPLY
COLD
WATER
SUPPLY
HOT IN
COPPER PIPE
COLD IN
MIXER VALVE
Loading...