™
J-SHA
Whirlpool Bath
Installation / Operating Instructions
II
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE HYDROMASSAGE
BATHTUB WITHOUT ADULT SUPERVISION.
WARNING : TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE
BATHTUB
WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE HYDROMASSAGE BATHTUB
UNLESS ALL SUCTION GUARDS ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT.
WARNING: KEEP BODY AND HAIR A MINIMUM OF 6" AWAY FROM SUCTION FITTING AT ALL TIMES WHEN
THE WHIRLPOOL SYSTEM IS OPERATING. HAIR LONGER THAN SHOULDER LENGTH SHOULD BE SECURED
CLOSE TO THE HEAD.
WARNING: RISK OF ELECTRICAL SHOCK; DO NOT PERMIT ELECTRICAL APPLIANCES (SUCH AS HAIR
DRYER, LAMP, TELEPHONE, RADIO OR TELEVISION) WITHIN 60" (1.5 M) OF THIS HYDROMASSAGE
BATHTUB.
WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE DRUGS OR ALCOHOL BEFORE OR
DURING THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID UNCONSCIOUSNESS AND POSSIBLE DROWNING.
WARNING: RISK OF FETAL INJURY; PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT A
PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.
WARNING: RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; DO NOT USE A HYDROMASSAGE
BATHTUB EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.
CAUTION; TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODICALLY IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS.
WARNING: RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; WATER TEMPERATURE IN EXCESS OF
100°F (38° C) MAY BE INJURIOUS TO YOUR HEALTH. CHECK AND ADJUST WATER TEMPERATURE BEFORE
USE.
WARNING: RISK OF HYPERTHERMIA; PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A HYRDOMASSAGE BATHTUB
EQUIPPED WITH A HEATER.
AN EQUIPMENT GROUNDING TERMINAL IS PROVIDED IN THE FIELD WIRING COMPARTMENT. TO REDUCE
THE RISK OF ELECTRICAL SHOCK, THIS TERMINAL MUST BE CONNECTED TO THE GROUNDING MEANS
PROVIDED IN THE ELECTRICAL SUPPLY PANEL WITH A CONNECTOR EQUIVALENT IN SIZE TO THE CIRCUIT
CONNECTORS SUPPLYING THIS EQUIPMENT.
PRECAUTIONS
Do not operate the whirlpool system unless the bath is filled with water to at least 2" above the highest jet.
Never drop or insert any object into any opening.
Do not use oil-based bath additives in your whirlpool bath.
When cleaning your bath, do not use abrasive substances which will damage the bath's surface.
To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).
The whirlpool system should be purged at least twice a month. For your convenience, we have developed a
plumbing system cleaner (Systems Clean™) specifically for whirlpool baths. For availability call 1-800-288-4002.
Use this unit only for its intended purpose as described in this manual. Do not use attachments not recommended
by the manufacturer.
This unit must be connected only to a supply circuit that is protected by a ground fault circuit interrupter (GFCI).
Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the
test button. The GFCI should interrupt power . Push the reset button. Power should be restored. If the GFCI fails to
operate in this manner, there is a ground current flowing, indicating a possibility of an electric shock. Do not use this
unit. Disconnect the unit and have the problem corrected by a qualified electrician before using.
A pressure wire connector is provided on the exterior of the motor to permit connection of an No. 8 A WG (8.4 mm)
solid copper bonding conductor between this unit and all other electric equipment and exposed metal in the vicinity ,
as needed to comply with local requirements.
This unit should be installed by a licensed electrician and grounded.
For built-in and drop-in units, install to permit access for servicing.
Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does not cover improper installation related problems.
16
Contents
Specifications _______________________________________________________________________ 1
Framing and Support _________________________________________________________________ 2
Rough-in Reference __________________________________________________________________ 2
Electrical and Service Access ___________________________________________________________ 3
Drain Information_____________________________________________________________________ 4
Plumbing and Water Supply ____________________________________________________________ 5
Water Level Sensor___________________________________________________________________ 6
Rapid Heat™ Operation ________________________________________________________________ 6
Operation __________________________________________________________________________ 7-11
Maintenance ________________________________________________________________________ 12-13
Warranty ___________________________________________________________________________ 15-16
Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and
fittings necessary for whirlpool operation. The drain/overflow kit must be installed on the bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been
made. Do not lift the bath by the plumbing at any time; handle by the shell or frame only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the
finish, do not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the
warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good
order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations,
refer to the warranty information.
All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to
installation, the bath must be filled to the overflow with water and operated to check for leaks that may have
resulted from shipping damage or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could
have been discovered, repaired, or avoided by following this inspection and testing procedure.
Save These Instructions for Future Use.
Owner's Record
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Number ___________________________
J-Sha II Owner's Manual
Specifications
DIMENSIONS
71-3/4" (1822 mm) L
36" ( 914 mm) W
21-1/4" ( 546 mm) H
(914 mm)
MOTOR/PUMP
115 VAC
Single phase
60 Hz.
(456 mm)
36"
18"
FLOOR
LOADING
47 lb/sq. ft.
(229 kg/sq. m)
9-7/16" (240 mm)
OPERATING
GALLONAGE
72 U.S. gal
(273 liters)
71-3/4"
(1822 mm)
PRODUCT
WEIGHT
125 lb
(57 kg)
RAPIDHEAT
ELECTRICAL
REQUIREMENTS
115 VAC 60 Hz.
15 Amp
Single Phase
(Must be GFCI
Protected)
BATH
ELECTRICAL
REQUIREMENTS
115 VAC 60 Hz.
20 Amp
Single Phase
(Must be GFCI
Protected)
5-3/8"
21-1/4"
(540 mm)
TOP VIEW
(137 mm)
2
(51 mm)
SIDE VIEW
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
1
J-Sha II Owner's Manual
Framing and Support
The floor structure beneath the bath must be able to support a total weight of bath, water, and bather.
If the subfloor is level, no other preparation is necessary. You can proceed to install the bath. If the subfloor is
not level, you MUST level the entire surface prior to installing the bath. Use a floor leveling compound. Do not
use mortar, plaster or minimal expansion structural foam to set the bath as this will interfere with bath components
on the bottom of the bath. Both sides of a joint or splice of subfloor should be level to each other.
The rim of the bath is not designed to support weight. If finish material is to overlap or contact the bath, the added
weight must be fully self-supporting.
The protective film liner inside the bath is used to prevent damage to the finish from shoes, tools, etc.
during installation. Before installation, remove liner to inspect for any defects, reapply and do not remove until final cleanup.
TYPICAL INSTALLATIONS
MORTAR OR
ADHESIVE
FLASHING
1" X 4" (NOT FOR SUPPORT)
FLUSH TO WALL
TILE
SEALANT
Rough-in Reference
The drain requires a cutout in the floor.
MORTAR OR
ADHESIVE
SEALANT
SUB-FLOOR
FLASHING
1" X 4" (NOT FOR SUPPORT)
SEMI-SUNKEN
9-7/16"
(240 mm)
(*1822 mm)
*71-3/4"
TILE
FINISHING
MATERIAL
PLASTER
FILLER
FLANGE
NAIL OR
SCREW
STUD
WALL
OPTIONAL TILE FLANGE KIT
MORTAR
CEMENT BOARD
BATH RIM
SILICONE
SEALANT
1" X 4"
(NOT FOR SUPPORT)
457 mm
36"
(900 mm)
*
Add1/4” (6 mm) to this dimension when roughing-in for 3 wall niche.
For semi-sunken installations, floor cutout is 69-3/4" x 34" (1772 mm x 864 mm).
(18")
13" x 4"
DRAIN/OVERFLOW
CUTOUT
18"
(457 mm)
2
J-Sha II Owner's Manual
MOTOR
AREA
A
AREA
B
SERVICE ACCESS
Electrical Connections
Two separate circuits are required for this unit:
1. Whirlpool bath controller.
2. Rapid Heat.
1. J-Sha II
Install a 120 VAC 20 AMP dedicated circuit protected by
a Ground Fault Circuit Interrupter (GFCI).
DANGER: RISK OF ELECTRIC SHOCK. Connect
only to a circuit protected by a Ground Fault Circuit
Interrupter.
2. Rapid Heat
Install a 120 VAC 15 AMP dedicated circuit with GFCI
protection. For operation, refer to the RapidHeat instructions.
DANGER: RISK OF ELECTRIC SHOCK. Connect
only to a circuit protected by a Ground Fault Circuit
Interrupter.
ELECTRICAL
CONTROL
BOX
CONNECTION
Service Access
For partially or fully sunken installations, allow for
service access as shown. It is the installer's responsibility to provide sufficient service access. Provide
adequate ventilation to cool the motor and to supply
sufficient air for the jets.
PROVIDE SERVICE ACCESS TO
THE THREE SIDES AS SHOWN
In some cases, access may not have been provided
because of the design of the bath environment and
having full understanding that in this case, it may be
necessary to remove the unit for service.
If this is the case, diagnosing a problem may not be
possible without complete access to the plumbing system. This would necessitate the removal of the unit.
Although this practice is not commonly implemented, it
is an acceptable method.
HEATER "ON"
MIN.
WARM
HOT
OVER HEAT
PROTECTION
PUSH TO RESET
TM
RAPID HEAT
SEPERATE GFCI
PROTECTED
CIRCUITS
In some cases access may have been provided in Area
A but service is required in Area B which requires the unit
to be pulled for service and reinstalled.
If service access has not been provided, it is the
home owners responsibility to remove the bath and
provide the required access, should a repair become necessary.
3
J-Sha II Owner's Manual
Drain Information
A drain/overflow assembly must be installed on the bath, water tested, and connected to the sanitary system of the
house. After opening the carton, inspect for damage. A solvent weld type drain is included and must be installed as
shown. The drain solenoid wiring plug must be connected to the control box prior to drain/overflow assembly. The
plug position (Drain Solenid) is shown on the control box. It is recommended that the tail pipe be installed on the drain
before the drain/overflow is installed on the bath. Hand tighten and then use a wrench to tighten until the tail pipe does
not turn. Follow the installation instructions provided with the drain/overflow kit to install the drain/overflow assembly.
Note: the bath must be propped up due to the length of the tail pipe.
NOTE: Watertight installation of the drain is the installer's responsibility. Drain leakage is excluded from the
Jacuzzi Whirlpool Bath warranty of this product.
1-1/2" TO 1-1/4" BUSHING (2)
1-1/4" FLEXIBLE PIPE
60°
1-1/2" RIGID PIPE
(NOT PROVIDED)
SOLENOID WIRING
TO CONTROL BOX
SPRING
CLAMPS
BACK JET MANIFOLD
DRAIN SOLENOID VALVE
4
TO BACK JET
DRAIN HOSE
J-Sha II Owner's Manual
Plumbing
Pump, jets, and suction fittings for the whirlpool system are factory plumbed in a combination of metric and schedule
40 PVC piping. All Jacuzzi Whirlpool Bath products are factory tested for proper operation and watertight connections
prior to shipping.
Before securing the bath to the floor, a test should be made for possible water leaks. Fill the bath until the nozzles
on the back rest are covered. If leaks are detected, notify your Jacuzzi Whirlpool Bath Dealer. Do not install the unit.
BACK REST NOZZLES
Water Supply
Consult local authorities for plumbing code requirements in your area.
IMPORTANT: Proper installation of the fill spout plumbing and compliance with local codes are the
responsibility of the installer. Jacuzzi Whirlpool Bath does not warrant connections of water supply fittings
and piping, fill systems, or drain/overflow systems. Nor is it responsible for damage to the bath which occurs
during installation.
CAUTION: A nonflammable protective barrier must be placed between soldering work and bath unit to prevent
damage to the bath.
21-1/2"
5
J-Sha II Owner's Manual
WATER LEVEL SENSOR
The bath is equipped with a water level sensor. When the water level is below the sensor, the pump/motor can
not be activated. When the water goes above the level sensor, the pump/motor can then be activated. If the
water level drops below the level sensor, the pump/motor will shut off. To restart the pump/motor after the water
level goes above the level sensor, the ON/OFF button must be pressed.
WATER LEVEL SENSOR
RAPIDHEAT
Operation
Once the heater is installed and the whirlpool pump is operating, the heating function is totally automatic. The
heater will help maintain the temperature of the water in the bath.
Vacuum Switch
The heater is equipped with a preset vacuum switch which will not allow the heater to turn ON if the pump is not
running with water flowing through the whirlpool system.
High-Limit Switch
The heater includes an exclusive High-Limit switch. This safety circuit will not false trip from hot tap water. It will
only turn off the heater if the thermostat fails. To reset, press the button. If the high-limit trips frequently, contact
your dealer.
6
J-Sha II Owner's Manual
Operation
Control Panel
ON
OFF
MIX
+
_
+
025
_
+
_
Control Panel Functions
TIME
_
SPEED
_
INTENSITY
_
TONI C
RELAX
80-130
110 - 15 0
130-220
+
+
+
LEDs
ON
OFF
MIX
ON/OFF Button: Turns system on or off.
BODY JET Button: Turns the body jets on or off.
BACK JET Button: Selects the massage cycle.
MIX Button: Selects both body jets and back jets.
AIR Button: Turns air on and increases air flow.
AIR Button: Decreases air flow. Turns off air.
LIGHT Button: Turns light on or off.
7
J-Sha II Owner's Manual
Control Panel Functions
ROLLING WAVE Button:
Turns on the rolling whirlpool
jet action pattern.
SQUARE WAVE Button:
Turns on the square whirlpool
jet action pattern.
TONIC/RELAX Button: Select either
the Tonic or Relax cycle. The LED will
light to indicate which cycle is selected.
+
_
+
_
+
_
(BODY JET ADJUSTMENT ONLY)
MAXIMUM PEAK Buttons: Increases (+)
or decreases (-) the maximum peak of the
rolling or square whirlpool jet action pattern.
MINIMUM PEAK Buttons: Increases (+)
or decreases (-) the minimum peak of the
rolling or square whirlpool jet action pattern.
FREQUENCY Buttons: Increases (+) or
decreases (-) the frequency or speed of the
rolling or square whirlpool jet action pattern.
TONIC
RELAX
BODY WEIGHT Button: Selects a body
weight range. The LED will light to
indicate which weight range is selected.
TIME Buttons: Increases (+) or decreases (-)
the time of programmed cycle.
SPEED Button: Increases (+) or decreases (-)
the travel (on/off) speed of the back jets.
INTENSITY Button: Increases (+)
or decreases (-) the power of the
back and body jets.
80-130
110 - 15 0
130-220
025
TIME
_
_
INTENSITY
+
SPEED
+
_
+
8
LED scale that
displays the time,
speed or intensity.
J-Sha II Owner's Manual
START UP BACK JETS
ON/OFF BUTTON
& LED
BACK JETS BUTTON
& LED
ON
OFF
MIX
START UP
Press ON/OFF button.
On start-up the J-Sha II will be in the default mode:
BACK JET LED lights up. Back jets operate after
about 2 seconds.
The TONIC indicator will be on. The flow from the
jets is from the bottom upward.
BODY WEIGHT of 110-150 LED will be on.
DURA TION, SPEED and INTENSITY relative indica-
tors will be on.
+
_
+
_
+
_
TONIC
RELAX
80-130
110-150
130-220
025
TIME
_
_
_
+
SPEED
+
INTENSITY
+
TONIC/RELAX BUTTON
& LED
BODY WEIGHT BUTTON
& LEDs
TIME BUTTON
& LED SCALE
SPEED BUTTON
& LED SCALE
INTENSITY BUTTON
& LED SCALE
VARIATIONS FROM DEFAULT SETTINGS
BODY WEIGHT RANGE:
Press the BODY WEIGHT button until the appropriate LED comes on. The duration will automatically
change the length of the cycle and the maximum
power of the jets.
TONIC to RELAX:
Press the TONIC/RELAX button. The RELAX LED
comes on. The flow from the jets is now from top to
bottom.
The DURA TION , SPEED and POWER of the back jets
have been preprogrammed for each body weight range.
The duration for 80-130 lbs. is 15 minutes, 110-150
lbs. is 18 minutes and 130 -220 lbs. is 21 minutes.
The speed is the velocity at which water moves up or
down on the back jets. The intensity is the water pres-
sure from the jets.
During the cycle, both speed and intensity gradually
increase to a maximum level determined for each body
weight range.
TIME, SPEED and INTENSITY:
Repeatedly press + or - buttons for each function.
Variations from the standard value are displayed by
the relative LED scales.
NOTE: During the BACK JETS (Shiatsu) cycle, the intensity and speed of the back jets are gradually increased. Any change of these values has an immediate effect.
9
J-Sha II Owner's Manual
WHIRLPOOL OPERATION
ROLLING WAVE BUTTON & LED
MAXIMUM PEAK BUTTONS & LED
ON/OFF BUTTON
& LED
BODY JETS BUTTON
& LED
AIR INCREASE
& DECREASE
BUTTONS & LED
SQUARE WAVE BUTTON & LED
ON
OFF
MIX
WHIRLPOOL
Press BODY JETS button:
The body jets led will come on while the TONIC indi-
cator, 110-150 LED and the SPEED scale will all turn
off. The value on the TIME and INTENSITY scales
will change to preprogrammed values. The duration
of this cycle is about 20 minutes. The intensity of the
jets are held constant and the air is off.
VARIATIONS FROM DEFAULT SETTINGS
TIME or INTENSITY:
Repeatedly press + or - buttons for each function.
Variations from the preprogrammed values are dis-
played by the relative LED scales.
AIR:
The default for body jets is air off. Press the upper
AIR button to turn on the air flow. The LED turns on.
Press the upper button to increase the air flow from
the body jets. Press the lower air flow to decreases
air flow. When the LED goes off, the air is off.
For pulsating air flow, press and hold the upper or
lower air button twice. The LED flashes to indicate
this mode. To turn off press either button once again.
TONIC
RELAX
TIME
_
SPEED
_
INTENSITY
_
80-130
110-150
130-220
+
+
+
+
_
+
025
_
+
_
FREQUECY BUTTONS & LED
ROLLING function:
Press the ROLLING button. The LED comes on. In
this cycle the intensity of the jets is gently modulated
with repeated pulses. The cycle starts with a minimum intensity to a maximum intensity with an immediate drop off toward the minimum. Press again to
return to continuous flow operation.
SQUARE function:
Press the SQUARE button. The LED comes on. In
this cycle the intensity of the jets is energetically modulated with short repeated pulses. The maximum peak
will last for an interval then drop off to the minimum.
Press again to return to continuous flow operation.
FREQUENCY:
The speed of the whirlpool jet action can be increased
or decreased by the use of these buttons. Press + or
- buttons to increase or decrease the frequency of
either the rolling or square pulses. The LED comes
on.
MAXIMUM & MINIMUM PEAKS:
The whirlpool jet action can be made more or less
gentle, or more or less forceful by use of these buttons. Press + or - buttons to increase or decrease
the maximum or minimum peaks of either the rolling
or square pulses. The LEDs comes on.
TIME BUTTON
& LED SCALE
MINIMUM PEAK
BUTTON & LED
INTENSITY BUTTON
& LED SCALE
10
J-Sha II Owner's Manual
MIX OPERATION (BACK AND BODY JETS)
ON/OFF BUTTON
& LED
MIX BUTTON
AIR INCREASE
& DECREASE
BUTTONS & LED
ON
OFF
MIX
MIX
Both back jets and body jets operate in this mode.
+
_
+
_
+
_
TONIC
RELAX
80-130
110-150
130-220
025
TIME
_
_
_
the relative LED scales.
+
SPEED
+
INTENSITY
+
TIME BUTTON
& LED SCALE
SPEED BUTTON
& LED SCALE
INTENSITY BUTTON
& LED SCALE
Press MIX button:
BACK JETS and BODY WEIGHT LEDs remain off.
INTENSITY indicator will be completely lit. The dura-
tion of this cycle is about 20 minutes. The back jets
flow is from lower to upper jets with gradually increas-
ing speed.
TONIC/RELAX MODE
VARIATIONS FROM DEFAULT SETTINGS
BODY WEIGHT AND ROLLING OR SQUARE :
Body weight and rolling or square function can not be
set during MIX mode.
TIME, SPEED and INTENSITY:
Repeatedly press + or - buttons for each function.
Variations from the standard value are displayed by
IMPORTANT
When exiting the bath, the water level will drop below the back jets which could result in water being sprayed out of
the unit. To prevent this, you must turn off the unit before exiting the bath.
AIR:
The default for body jets is air off. Press the upper
AIR button to turn on the air flow. The LED turns on.
Press the upper button to increase the air flow from
the body jets. Press the lower air flow to decreases
air flow. When the LED goes off, the air is off.
For pulsating air flow, press and hold the upper or
lower air button twice. The LED flashes to indicate
this mode. To turn off press either button once again.
11
Maintenance
Back Jet Manifold Drainage
When the unit is turned off, the back jet manifold will continue to drain after the bath is empty
Cleaning the J-Sha
To clean your J-Sha whirlpool bath, simply use a mild nonabrasive liquid detergent or commercially prepared bathtub
cleaner. Do not use abrasive cleaners. You can protect and restore the gloss to a dulled surface by applying a polish
specifically designed for use on acrylic finishes. If an acrylic polish is not available, an automotive paste wax can be
used.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the whirlpool system, it is recommended that a whirlpool bath be purged
at least twice a month. For best results, however, we recommend that you purge your whirlpool bath after each use
using our exclusive two-part plumbing system cleaner made specifically for whirlpool baths. Systems Clean ™ is
available through an authorized Jacuzzi Whirlpool Bath Distributor or by calling us direct at 1-800-288-4002.
Instructions for use: Immediately after bathing and exiting the whirlpool bath, leave the bath water in the tub and add
hot water, if necessary, so the water is at least 2" above the highest jet. Turn on the unit without the aerator. Pour
the contents of the Systems Clean Packet 1 (taking care not to get the material on yourself) into the bath near the intake
for the circulation pump. Repeat same process with Systems Clean Packet 2. It is important to use Packet 1 before
Packet 2 to avoid a strong odor. Run the bath for 5 to 10 minutes. Drain completely and rinse any residue.
If you have followed the standard purging instructions above and still have an excess accumulation of bath residue
and desire an alternative cleaning mechanism, we recommend SUPER SYSTEMS CLEAN PLUS manufactured by
Stearns Packaging to rectify this condition. This may be obtained by contacting us at l-800-288-4002. It is
recommended that you follow the instructions provided by the manufacturer with the product. Repeated use may be
necessary. SUPER SYSTEMS CLEAN PLUS does not replace the necessity to regularly purge your whirlpool system
with Systems Clean as recommended.
(For additional information about water content, contact us for a copy of the Jacuzzi Water Quality Primer.)
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.
If you want to use any kind of bath additive, use only a small amount of low-foaming powder or crystal substance; the
whirlpool action intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath additives may increase the level of accumulations of bath residue
in the whirlpool system. If excess accumulations persist, you should discontinue use of these products.
12
Repairs to the Surface
Minor scratches which do not penetrate the color finish (acrylic) can be removed with 600-grit wet/dry sandpaper.
Restore the glossy finish with an acrylic polish or a comparable automotive paste wax. Major scratches or gouges
which penetrate the acrylic surface require refinishing. Ask your dealer for special instructions.
Lamp
When the bulb burns out, replace it from the back of the lamp fitting, on the underside of the shell, by pulling out the
bulb receptacle. Replacement bulbs (7W, 12V) are available from your Jacuzzi Whirlpool Bath dealer.
LIGHT BULB REPLACEMENT
LOCKING NUT
LIGHT BULB
BULB
RECEPTACLE
LIGHT BEZEL
SHELL
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type.
It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of this product. Jacuzzi Whirlpool
Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath National Headquarters
P.O. Drawer J, Walnut Creek, CA 94596 (925) 938-7070
Service Support: Call (800) 288-4002
©1999 Jacuzzi Whirlpool Bath P946000 5/5/03
Printed on Recycled Paper
13
Printed in the U.S.A.
14
Jacuzzi Whirlpool Bath Limited Warranty
Designer Collection Bath Product
WARRANTY COVERAGE
Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer
Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the
unit or its equipment in accordance with the following terms and conditions.
TWO YEAR LIMITED WARRANTY ON BATHS
Our limited warranty on Designer Collection Bath products is for two (2) years. Our warranty covers the unit and factory-installed components (e.g.,
pump, motor) against defects in material or workmanship. Warranty coverage begins on the date the unit was originally purchased by the user.
FIVE YEAR (PARTS ONLY) LIMITED WARRANTY ON PUMP AND MOTOR
Our limited warranty on the pump and motor is for five (5) years for parts only. Warranty coverage begins on the date the unit was originally purchased by the
user.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
Our limited warranty on options and accessories manufactured by the Company is for ninety (90) days for parts only. Our warranty covers options and
accessories manufactured by the Company (e.g., fill spout kits, trim kits, skirts) against defects of material or workmanship. Warranty coverage begins on the
date the option or accessory was originally purchased by the user.
WARRANTY LIMITATIONS
Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other person, or resulting from, without
limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.); modification of any type for any reason (including modification
to meet local codes); improper installation (including installation not in accordance with instructions and specifications provided with the unit); connections
supplied by the installer of the equipment; improper voltage supply or unauthorized electrical modification; misuse; incorrect operation, or lack of proper routine
maintenance; operation of the unit without specified minimum amount of water or at inappropriate water temperature; use of abrasive or improper cleaners; or
acts of God, such as lightning, floods, earthquakes, etc.
In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause
(e.g., water damage to carpet, ceiling, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts when pool and/or spa
chemicals are used in the unit; optional bath equipment not manufactured by the Company but supplied by Dealer, installer or the Company; the unit's prior usage
as an operational display; or defects that should have been discovered before installation. This limited warranty does not include: labor, transportation, or other
costs incurred in the removal and/or reinstallation of the original unit and/or installation of a replacement unit; any costs relating to obtaining access for repair;
or loss of use damage, including loss of sales, profit or business advantage of any kind under any circumstances. Bath units are excluded from any warranty coverage
if any addition, deletion, or modification of any kind whatsoever has been made to the unit (or to any component).
Warranty coverage is provided in the United States of America only.
EXCLUSION OF IMPLIED WARRANTIES
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO
THE FULL EXTENT ALLOWED BY LAW.
NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable
to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not be responsible for
any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature or specifications furnished
by the Company.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above
limitations and exclusions may not apply to you.
RETURN OF WARRANTY CARD
The attached Warranty Registration Card MUST be filled out by the purchaser within thirty (30) days from purchase and mailed to Jacuzzi Whirlpool Bath
in order for this warranty to become effective.
Jacuzzi Whirlpool Bath
P.O. Drawer J
Walnut Creek, CA 94596-9885
RESPONSIBILITIES OF OTHERS
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring
the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of
a problem, the unit must not be installed. The Company is not responsible for failures or damage that could have been discovered, repaired, or avoided by proper
inspection and testing prior to installation.
Damage occurring in transit is the responsibility of the carrier. The user or installer MUST open the crate and inspect the unit for damage when it is delivered.
If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure of the carrier to respond should
be reported to the seller and the carrier. Your freight claims should be filed promptly thereafter.
It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs relating to
obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.
Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the
responsibility of the user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (Options and accessories manufactured by the Company are
warranted for ninety (90) days from the original date of purchase for parts only.)
The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these requirements at the
time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state building codes.
WARRANTY SERVICE
For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such firms are not agents
or representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered
by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the
problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure
occurred or was discovered within the warranty period; an authorized independent service person or Company representative has been permitted to inspect the
unit during regular business hours within a reasonable time after the problem was reported by the user.
In order to obtain warranty service, consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service Agent. Describe
the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service.
If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:
Jacuzzi Whirlpool Bath
Warranty Service Department
P.O. Drawer J
Walnut Creek, California 94596
Call: (800) 288-4002
To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied by the Company,
call or write the above. Provide a description of the problem and proof of purchase. You will be instructed how to obtain replacements and where to return, at
your expense, the failed component(s), option(s), or accessory(ies).
All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender terminates the
Company's warranty obligation.
©1998 Jacuzzi Whirlpool Bath P946000 5/5/03
Limited Warranty
Accessory(ies)
Ninety-Day
Parts Only
On
Limited Warranty
Accessory(ies)
Ninety-Day
Parts Only
10.Approximately how long have you lived in this home? ___________
12.Was your purchase process?
13.How technically aware were you of the patented Jacuzzi® jet system
( ) $40,000 to $49,999 ( ) $150,000 and Above
( ) Very easy ( ) Easy ( ) Difficult ( ) Very Difficult
prior to your puchase?
( ) Not aware ( ) Somewhat aware ( ) Very aware
11.Please indicate, approximately, the total annual income of your
( ) 1 month-2 months
household.
( ) Up to $24,999 ( ) $50,000 to $74,999
( ) $25,000 to $29,999 ( ) $75,000 to $99,999
( ) $30,000 to $39,999 ( ) $100,000 to $149,999
9. How long did you shop before purchasing unit?
Please estimate $ _______________________________________
( ) Eljer ( ) Lasco ( ) Price Pfister ( ) Aqua Glass
( ) Kohler ( ) American Standard ( ) Sterling
( ) Other (Specify) _____________________________________
( ) 1 day ( ) 2 months-6 months
( ) 2-7 days ( ) 6 months-1year
( ) 1 week-2 weeks ( ) 1 year-2 years
( ) 2 weeks-4 weeks ( ) +2 years
6. What is the current market value of this property?
7. What is the age of the head of the household? _____________ years
8. What other manufacturers did you consider?
4. Who finally decided which product you would buy?
5. Who installed? ( ) Already installed/New Home
( ) Self ( ) Spouse ( ) Self and Spouse Together
( ) Other Family Member ( ) Designer/Architect
( ) Builder/Plumber/Remodeler ( ) Already Installed
( ) Contractor/Plumber when remodeling
( ) Self/Spouse when remodeling
( ) Other _____________________________________________
3. What was the main reason for purchase?
( ) Styling ( ) Warranty Service ( ) Product Features
( ) Brand Name ( ) Price ( ) Hydrotherapy
( ) Home Resale _______________________________________
( ) Other _____________________________________________
2. Who first gave you specific information about this product (specifications,
( ) Word of Mouth . . . Friend/Relative/Acquaintance
( ) Other (Please Describe)_______________________________
prices, etc.)?
( ) Dealer/Plumbing Supplier ( ) Builder ( ) Remodeler
( ) Plumbing Contractor ( ) Retailer/Home Center Store
( ) Decorator/Architect ( ) Already Installed
1. How did you first hear about this Jacuzzi® product?
( ) Advertisement ( ) Article in Magazine/Newspaper
( ) Visited Dealer/Plumbing Supplier ( ) Yellow Pages
( ) Builder/Plumber/Remodeler ( ) Decorator/Architect
( ) Visited Retailer/Home Center Store
Model Name _____________________________________________
Serial Number ___________________________________________
Dealer's Name ___________________________________________
Dealer's Address__________________________________________
On
This card must be filled out and returned to the address printed on the other
side within thirty (30) days from date of purchase in order for this warranty to
be come effective.
Purchaser's Name ________________________________________
Purchaser's Address _______________________________________
City _____________________________ State _____ Zip ________
Date of Purchase _________________________________________
P946000
5/5/03
Warranty
Registration Card
Loading...