Page 1
• J-585
™
• J-575
™
J-500
™
COLLECTION
OWNER’S MANUAL
2530-278D Rev A
Page 2
Attention New Spa Owner!
Congratulations on the purchase of your new Jacuzzi® spa! The following is a
list of automated functions performed by your spa. These functions are listed
below in an attempt to suppress any operational concerns you may have during
the rst 24 hours of ownership! Also listed below are important maintenance
recommendations you should observe on a regular basis to protect your new
investment.
Maintain Healthy Spa Water
Always maintain your spa’s water chemistry within the following parameters:
With CLEARRAY ® Without CLEARRAY ®
pH 7.4-7.6 7.4-7.6
Free chlorine no less than 1.0 ppm 3.0-4.0 ppm
Free bromine no less than 2.0 ppm 2.0-4.0 ppm
Total Alkalinity 100-150 ppm 100-150 ppm
Calcium Hardness 150-250 ppm 150-250 ppm
IMPORTANT: CLEARRAY ® Water Purication System is factory installed. If
the CLEARRAY ® system is altered or is not operating efciently then follow
the “without CLEARRAY ®” water chemistry parameters as dened by the
Association of Pool and Spa Professionals. CLEARRAY ® requires an annual
bulb replacement to properly sanitize your water.
!
TO DECREASE RISK OF INFECTION OR DISEASE! Always maintain
your spa lter as outlined below to ensure healthy spa water. Refer to pages
51-54 (Sec. 13.0) for additional information.
Required Filter Maintenance
Your new spa is equipped with an advanced water ltration system that provides
unsurpassed water quality! To ensure maximum water quality at all times, you
should clean the skimming lter cartridge every 3 months, or as necessary. See
pages 51-54 (Sec. 13.0) for detailed lter cartridge cleaning instructions.
Required Water Replacement
!
TO DECREASE RISK OF INFECTION OR DISEASE! You should
replace the spa’s water every 3 months. The frequency depends on a number
of variables including frequency of use, number of users and attention paid to
water quality maintenance. You will know it is time for a change when you cannot
control sudsing and/or you can no longer get the normal feel or sparkle to the
water, even though the key water balance measurements are all within the proper
parameters. See pages 59-62 (Sec. 14.0) for additional information.
****** Spa operation subject to change without notice ******
©Jacuzzi Hot Tubs, Inc. All Rights Reserved
Page 3
Table of Contents
1.0 Important Spa Owner Information .............................................. 1
2.0 FCC Notice .................................................................................... 1
2.1 Industry Canada (IC) Information .................................................. 1
3.0 Important Safety Instructions for all Spa Owners .................... 2
3.1 Entrapment Risk ............................................................................ 6
3.2 Hyperthermia ................................................................................. 7
3.3 Important CSA safety instructions (Canada only) .......................... 8
4.0 Choosing a Location.................................................................... 8
4.1 Outdoor Location ........................................................................... 9
4.2 Indoor Location ............................................................................ 10
4.3 Location for the ProLink™ Monitoring System ............................ 11
5.0 General Electrical Safety Instructions ..................................... 12
6.0 Electrical Installation Instructions (240V Service) .................. 12
7.0 Power Requirements ................................................................. 16
8.0 Spa Fill Up Procedure ................................................................ 17
9.0 Spa Features .............................................................................. 22
9.1 J-575 Spa Features ..................................................................... 22
9.2 J-575 Massage/Waterfall Selector Diagram ................................ 23
9.3 J-575 Air Controls Diagram.......................................................... 24
9.4 J-585 Spa Features ..................................................................... 25
9.5 J-585 Massage/Waterfall Selector Diagram ................................ 26
9.6 J-585 Air Controls Diagram.......................................................... 27
10.0 Registration and Start-up .......................................................... 28
10.1 Start-up Sequence ....................................................................... 28
10.2 Register Your New Spa................................................................ 28
10.3 ProTouch™ Glass Control Panel ................................................. 30
11.0 Operating Instructions............................................................... 32
11.1 ProTouch™ Glass Control Panel ................................................. 32
11.2 Activating the Jets Pumps ........................................................... 32
11.3 Lights Menu ................................................................................. 33
11.4 Interior Lights ............................................................................... 33
11.5 Exterior Lights .............................................................................. 34
11.6 Experience ................................................................................... 35
11.7 Music Menu ................................................................................. 35
11.8 Bluetooth® Pairing Instructions ................................................... 36
11.9 Audio Settings Menu.................................................................... 37
Page 4
11.10 CLEARRAY on Demand .............................................................. 38
11.11 Adjusting Jet Flow........................................................................ 38
11.12 Adjusting PowerPro™ MX2 Jets.................................................. 38
11.13 Adjusting RX Jets ........................................................................ 38
11.14 Waterfall Control .......................................................................... 38
11.15 Air Controls .................................................................................. 38
11.16 Selecting the Desired Massage Action ........................................ 39
11.17 Optional BLUEWAVE® 2.0 Wireless Audio System ....................39
12.0 Programming Instructions ........................................................ 40
12.1 Programming the Heating Mode .................................................. 41
12.2 Programming the Primary Filter ................................................... 41
12.3 Programming the Secondary Filter .............................................. 43
12.4 Cleaup Cycle ............................................................................... 43
12.5 Blow-Out Cycle ............................................................................ 43
12.6 Water Care Programming ............................................................ 44
12.7 Locking the Spa ........................................................................... 46
12.8 Programming the Time and Date ................................................. 48
12.9 Programming the Language ........................................................ 48
12.10 Wi-Fi Setup .................................................................................. 49
12.11 System Information ...................................................................... 50
13.0 Spa Maintenance ........................................................................ 51
13.1 Cleaning the Filter Cartridges ...................................................... 51
13.2 Draining and Relling................................................................... 55
13.3 Cleaning the Spa Interior ............................................................. 56
13.4 Pillow Care................................................................................... 57
13.5 Maintaining the Synthetic Cabinet ............................................... 57
13.6 Cleaning the Control Panel .......................................................... 57
13.7 Cover Care and Maintenance ...................................................... 57
13.8 Winterizing ................................................................................... 58
13.9 Restarting Your Spa in Cold Weather .......................................... 59
14.0 Water Quality Maintenance ....................................................... 59
14.1 pH Control.................................................................................... 60
14.2 Sanitizing ..................................................................................... 60
14.3 Other Additives ............................................................................ 61
14.4 CLEARRAY ® (Ultraviolet) Water Purication System ................. 61
14.5 CLEARR AY® Bulb Replacement and Quartz
Tube Maintenance .......................................................................... 62
15.0 Error/Display Messages ............................................................ 65
16.0 Troubleshooting Procedures .................................................... 68
Page 5
17.0 Typical Spa Wiring Diagrams .................................................... 70
17.1 Wiring diagram for North American 60 Hz Models Only .............. 70
18.0 Circuit Board Wiring Diagrams ................................................. 71
18.1 Domestic 60Hz Wiring Diagram................................................... 71
18.2 Export 50Hz Wiring Diagram ....................................................... 72
18.3 Dip Switch Settings ...................................................................... 73
18.4 Dual Service 50Hz Connection .................................................... 75
18.5 Single Service 50Hz Connection ................................................. 76
18.6 Three Phase Service 50Hz Connection....................................... 77
Page 6
Page 7
Page 1
1.0 Important Spa Owner Information
Your Jacuzzi® spa is constructed to the highest standards and is capable
of providing many years of trouble-free use. However, because heat reten-
tive materials are utilized to insulate the spa for efcient operation, an
uncovered spa surface and wall ttings directly exposed to sunlight and
high temperatures for an extended period are subject to permanent damage or discoloration. Damage caused by exposing the spa to this abuse
is not covered under warranty. We recommend that you always keep the
spa full of water when it is exposed to direct sunlight and that you keep the
Jacuzzi insulating cover in place at all times when the spa is not in use.
Read and carefully follow the requirements for your spa’s support base
found in the Section 4.0 titled, “Choosing a Location” (page 8).
Jacuzzi® spas constantly strives to offer the nest spas available,
therefore, modications and enhancements may be made which affect
the specications, illustrations and/or instructions contained herein.
2.0 FCC Notice
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1. Rearrange or relocate the receiving antenna;
2. Increase the separation between the equipment and receiver;
3. Connect the equipment into an outlet on a circuit different from the
circuit connected;
4. Consult the dealer or an experienced radio/TV technician for help.
(Changes or modications not expressly approved by the party
responsible for FCC compliance could void the user’s authority to
operate this equipment.)
2.1 Industry Canada (IC) Information
The installer of this radio equipment must ensure that the antenna
is located or pointed such that it does not emit RF eld in excess of
Health Canada limits for the general population; consult Safety Code 6,
obtainable from Health Canada’s website: www.hc-sc.gc.ca.
Page 8
Page 2
3.0 Important Safety Instructions for all Spa Owners
READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY!
This spa was manufactured to meet the standards and specications
outlined in the “Virginia Graeme Baker Pool and Spa Safety Act” (VGB
Safety Act). When installing and using this spa, basic safety precautions
should always be followed, including:
1.
!
DANGER: RISK OF SEVERE INJURY OR DROWNING!
• Extreme caution must be exercised to prevent unauthorized access
by children.
• To avoid accidents, ensure that children do not use this spa unless
supervised at all times. Adult supervision is a critical safety factor in
preventing children from drowning.
• Use the straps and clip tie downs to secure the spa cover when not
in use. This will help discourage unsupervised children from entering
the spa. Keep the spa cover secure in high-wind conditions.
• There is no representation that the cover, clip tie-downs, or actual
locks will prevent access to the spa.
2.
!
DANGER: RISK OF SEVERE INJURY OR DROWNING!
• Keep hair, loose articles of clothing or hanging jewelry away from
suction ttings, rotating jets or other moving components to avoid
entrapment that could lead to drowning or severe injury.
• Never use the spa unless all suction guards, lter, lter lid, or
skimmer assembly are installed to prevent body and/or hair
entrapment.
• Never operate or use the spa if the lter, lter lid, or skimmer
assembly are broken or any part of the skimmer assembly is missing.
Please contact your dealer or nearest service center for service.
• The suction ttings and suction covers in this spa are sized to match
the specic water ow created by the pump(s). If it is necessary to
replace the suction ttings, suction covers or pump(s), be sure that
the ow rates are compatible and are in compliance with the VGB
Safety Act.
• Never replace a suction tting or suction cover with one rated less
than the ow rate marked on the original suction tting. Using
improper suction ttings or suction covers can create a body or hair
suction entrapment hazard that may lead to drowning or severe
injury.
3.
!
DANGER: RISK OF SEVERE INJURY FROM ELECTRIC
SHOCK OR DEATH FROM ELECTROCUTION!
• Install the spa at least 5 feet (1.5m), from all metal surfaces. As an
alternative, a spa may be installed within 5 feet of metal surfaces
if each metal surface is permanently connected (bonded) by a
minimum No. 8 AWG (8.4 mm²) solid copper conductor attached
to the wire connector on the grounding lug, inside the equipment
compartment on the equipment box.
Page 9
Page 3
• A grounding wire connector is provided on this unit to connect a
minimum No. 8 AWG (8.4 mm²) solid copper conductor between
this unit and any metal equipment, metal enclosures of electrical
equipment, metal water pipe, or conduit within 5 feet (1.5m) of the
unit.
• Never permit any electrical appliance, such as a light, telephone,
radio, television, etc. within 5 feet (1.5m) of a spa unless such
appliances are built-in by the manufacturer.
• Never bring any electrical appliances into or near the spa.
• Never operate any electrical appliances from inside the spa or when
you are wet.
• The electrical supply for this product must include a suitably rated
switch or circuit breaker to open all ungrounded supply conductors
to comply with Section 422-20 of the National Electrical Code/USA,
ANSI/NFPA 70. The disconnecting means must be readily accessible
and visible to the spa occupant but installed at least 5 feet (1.5m),
from the spa.
• The electrical circuit supplied for the hot tub must include a suitable
ground fault circuit interrupter (GFCI) as required by NEC Article
680-42.
4.
!
WARNING: RISK OF SEVERE INJURY OR DEATH!
• Extreme caution must be exercised to prevent diving or jumping
into the spa or slipping and falling, which could result in
unconsciousness, drowning, or serious injury. Remember that wet
surfaces can be very slippery.
• Never stand, walk or sit on the top railing of the spa.
5.
!
WARNING: RISK OF HYPERTHERMIA (OVER-HEATING)
CAUSING SEVERE INJURY, BURNS, WELTS OR DEATH!
• Water temperature in excess of 104°F (40°C) may be injurious to
your health.
• Refer to Section 3.2 Hyperthermia for specic causes and symptoms
of this condition.
• The water in the spa should never exceed 104°F (40°C). Water
temperatures between 100°F (38°C) and 104°F (40°C) are
considered safe for a healthy adult.
• Lower water temperatures are recommended for young children
(children are especially sensitive to hot water) and when spa use
may exceed 10 minutes.
• The Consumer Products Safety Commission/USA has stated that the
water temperature in a spa should not exceed 104°F (40°C).
• Always test the spa water temperature before entering the spa.
The user should measure the water temperature with an accurate
thermometer since the tolerance of water temperature-regulating
devices may vary as much as +/- 5°F (2°C).
Page 10
Page 4
6.
!
WARNING: RISK OF SEVERE INJURY OR DEATH!
• Since excessive water temperatures have a high potential for causing
fetal damage during the early months of pregnancy, if pregnant or
possibly pregnant, consult your physician before using a spa.
• Pregnant or possibly pregnant women should limit spa water
temperatures to 100°F (38°C).
• Persons suffering from obesity or a medical history of heart disease,
low or high blood pressure, circulatory system problems, diabetes,
infectious diseases or immune deciency syndromes should consult a
physician before using a spa.
• If you experience breathing difculties in association with using or
operating your spa, discontinue use and consult your physician.
• Persons using medication should consult a physician before using
a spa since some medication may induce drowsiness, while other
medication may affect heart rate, blood pressure, and circulation.
• Persons suffering from any condition requiring medical treatment, the
elderly, or infants should consult with a physician before using a spa.
• The use of alcohol, drugs, or medication before or during spa use may
lead to unconsciousness with the possibility of drowning.
7.
!
WARNING: RISK OF SEVERE INJURY OR DEATH!
• Prolonged immersion in a spa may be injurious to your health.
• Observe a reasonable time limit when using the spa. Exposures at
higher temperatures can cause high body temperature (over-heating).
Symptoms may include dizziness, nausea, fainting, drowsiness, and
reduced awareness. These effects could possibly result in drowning or
serious injury.
• Never use a spa immediately following strenuous exercise. Enter and
exit the spa slowly. Wet surfaces can be slippery.
8.
!
WARNING: TO DECREASE RISK OF INFECTION OR DIS-
EASE!
• To reduce the risk of contracting a waterborne
illness (e.g. an infection,
bacteria or virus) and/or respiratory ailments
, maintain water chemistry
within the parameters listed on the inside cover of this manual and
consult with a licensed engineer regarding proper ventilation if installed
indoors or in an enclosed area.
• People with infectious diseases should not use a spa to avoid water
contamination, which could result in spreading infections to others.
• Always shower before and after using your spa. Maintain water chem-
istry in accordance with manufacturer’s instructions. Failure to do
so may result in contracting a waterborne
illness (e.g. an infection,
bacteria or virus).
Page 11
Page 5
9.
!
WARNING: In addition to maintenance of lters and water
chemistry, proper ventilation is recommended to reduce the risk of
contracting a waterborne
illness (e.g. an infection, bacteria or virus)
and/or respiratory ailments
that could be present in the air or water.
Consult a licensed architect or building contractor to determine your
specic needs if installing your hot tub indoors.
10. CAUTION: TO DECREASE RISK OF PRODUCT DAMAGE.
• Maintain water chemistry in accordance with manufacturer’s
instructions.
• Proper chemical maintenance of spa water is necessary to maintain
safe water and prevent possible damage to spa components.
11.
!
WARNING: RISK OF SEVERE INJURY OR DEATH! The
appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible
for their safety.
12. NOTE: This spa is not intended nor designed to be used in a com-
mercial or public application. The spa buyer shall determine whether
there are any code restrictions on the use or installation of this spa
since local code requirements vary from one locality to another.
Hot Tub Safety Literature
To ensure you have a safe and enjoyable hot tub experience,
learn all you can about hot tub safety and emergency procedures.
Especially useful are the brochures listed below:
• Children Aren’t Waterproof
• Pool and Spa Emergency Procedures For Infants and Children
• Layers of Protection
• The Sensible Way to Enjoy Your Spa or Hot Tub
The Association of Pool and Spa Professionals publishes these
brochures. To acquire a brochure:
• Ask your hot tub dealer (they may have copies)
• Go to http://apsp.org
• Conduct your own search on the internet
• Write to the following address:
The Association of Pool and Spa Professionals
2111 Eisenhower Avenue
Alexandria VA 22314
703.838.0083
Page 12
Page 6
3.1 Entrapment Risk
The Consumer Products Safety Commission/USA has reported that
users of pools and spas have become entrapped (stuck) to drain and/or
suction ttings causing death, drowning, or serious injury (see diagram
below). This spa was manufactured to meet the standards and specica-
tions outlined in the “Virginia Graeme Baker Pool and Spa Safety Act”
(VGB Safety Act). Entrapment risk can be minimized if proper precau-
tions are taken.
DANGER: RISK OF PERSONAL INJURY OR DEATH!
Never operate the spa if a suction tting, suction cover,
lter, lter lid or skimmer assembly are broken, damaged or
missing.
!
Note: Suction covers must be replaced every 5 years.
1.
!
DANGER: RISK OF SEVERE INJURY OR DROWNING!
Hair entrapment: May occur if hair is entangled, knotted or snagged
in a drain suction or skimmer assembly. This has been reported in
persons who when submerge themselves underwater, allowing hair
to come close and/or within the reach of the suction fittings, suction
covers or skimmer assembly.
• Keep hair away from suction ttings, suction covers, lter, lter lid or
skimmer assembly.
• Children are at risk for hair entrapment if swimming under water.
• Never allow children to play or get near the suction ttings, suction
covers, lter, lter lid or skimmer assembly.
2.
!
DANGER: RISK OF SEVERE INJURY OR DROWNING!
Limb entrapment: May occur when a limb becomes entrapped,
inserted or sucked into a suction or outlet opening.
• Always keep suction ttings, suction covers, lter, lter lid or skimmer
assembly in place when operating to avoid limb entrapment.
• Never allow children to play or get near the suction ttings, suction
covers, lter, lter lid or skimmer assembly.
Suction Fittings,
Suction Covers
(locations vary
by models)
Filter, Filter
Lid, Skimmer
Assembly
(location and
style vary by
models)
Page 13
Page 7
3.
!
DANGER: RISK OF SEVERE INJURY OR DROWNING!
Body entrapment: May occur when part of the torso becomes
entrapped, inserted or sucked into a suction or outlet opening.
• Never allow children to play or get near the suction ttings, suction
covers, lter, lter lid or skimmer assembly.
4.
!
DANGER: RISK OF SEVERE INJURY OR DROWNING!
Evisceration (disembowelment) entrapment: May occur when the
buttocks becomes entrapped, inserted or sucked into a suction or
outlet opening.
• Never sit on suction ttings, suction covers, lter, lter lid or skimmer
assembly.
• Never allow children to play or get near the suction ttings, suction
covers, lter, lter lid or skimmer assembly.
5.
!
DANGER: RISK OF SEVERE INJURY OR DROWNING!
Mechanical entrapment: May occur when jewelry, swimsuit, or
hair accessories become entangled, knotted or snagged in a drain
suction or skimmer assembly.
• Never allow your jewelry, swimsuit, or hair accessories to come close
to the suction ttings, suction covers or skimmer assembly.
• Never allow children to play or get near the suction ttings, suction
covers, lter, lter lid or skimmer assembly.
3.2 Hyperthermia
Prolonged immersion in hot water may induce hyperthermia (overheating). The use of alcohol or drugs can greatly increase the risk of fatal
hyperthermia in spas. A description of the causes, symptoms, and effects
of hyperthermia are as follows:
Hyperthermia occurs when the internal temperature of the body reaches
a level several degrees above the normal body temperature of 98.6°F
(37°C). The symptoms of hyperthermia include drowsiness, lethargy
(fatigue), and an increase in the internal temperature of the body (feeling
of being too hot). The effects of hyperthermia include:
• Unawareness of impending hazard;
• Failure to perceive heat;
• Failure to recognize the need to exit spa;
• Physical inability to exit spa;
• Fetal damage in pregnant women; and
• Unconsciousness and danger of drowning.
A Warning Sign is provided in your warranty packet. Please install at
a location near your spa, where it is visible to users of the spa. For
additional or replacement Warning Signs please contact your local
Jacuzzi dealer and reference item number #6530-082.
Page 14
Page 8
3.3 Important CSA safety instructions (Canada only)
When using this electrical equipment, basic safety precautions should
always be followed, including the following:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. A green colored terminal or a terminal marked G, Gr, Ground,
Grounding or the symbol* is located inside the supply terminal box
or compartment. To reduce the risk of electric shock, this terminal
must be connected to the grounding means provided in the electric
supply service panel with a continuous copper wire equivalent in size
to the circuit conductors that supply this equipment. *IEC Publication
417, Symbol 5019.
3. At least two lugs marked “Bonding Lugs” are provided on the
external surface or on the inside of the supply terminal box/
compartment. To reduce the risk of electric shock, connect the local
common bonding grid in the area of the spa to these terminals with
an insulated or bare copper conductor not smaller than No. 6 AWG
(10 mm²).
4. All eld-installed metal components such as rails, ladders, drains or
other similar hardware within 10 feet (3m) of the spa shall be bonded
to the equipment grounding buss with copper conductors not smaller
than No. 6 AWG (10 mm²).
5. SAVE THESE INSTRUCTIONS.
4.0 Choosing a Location
IMPORTANT: Because of the combined weight of the spa, water
and users, it is extremely important that the base upon which the
spa rests be smooth, at, level and capable of uniformly supporting this weight, without shifting or settling, for the entire time the
spa is in place. If the spa is placed on a surface, which does not
meet these requirements, damage to the skirt and/or the spa shell
may result. Damage caused by improper support is not covered
under warranty. It is the responsibility of the spa owner to assure
the integrity of the support at all times. We recommend a poured,
reinforced concrete slab with a minimum thickness of 4 inches
(10 cm). Wood decking is also acceptable provided it is constructed
so that it meets the requirements outlined above.
WARNING: For spas that are to rest on balconies, roofs
or other platforms not specically tied into main structural support, consult a professional Structural Engineer
with experience in this type of application.
!
Page 15
Page 9
The spa must be installed in such a manner as to provide drainage away
from it. Placing the spa in a depression without provisions for proper
drainage could allow rain, overow and other casual water to ood the
equipment and create a wet condition in which it would sit in. For spas
which will be recessed into a oor or deck, install so as to permit access
to the equipment, either from above or below, for servicing. Make certain
that there are no obstructions, which would prevent removal of all side
cabinet side panels and access to the jet components, especially on the
side with the equipment bay.
CAUTION: If the spa is indoors or located in an enclosed area,
proper ventilation should be discussed with an Engineer or authority
competent enough to understand the necessary provisions needed
to vent moist or heated air and air associated with chemical odors
outdoors. When the spa is in use considerable amounts of
moisture will escape potentially causing mold and mildew. This
can cause health risk. Over time, this can damage certain surfaces,
surroundings, and equipment.
4.1 Outdoor Location
In selecting the ideal outdoor location for your spa, we suggest that you
take into consideration:
• The proximity to changing area and shelter (especially in colder
weather).
• The pathway to and from your spa (this should be free of debris so
that dirt and leaves are not easily tracked into the spa).
• The closeness to trees and shrubbery (remember that leaves and
birds could create extra work in keeping the spa clean).
• A sheltered environment (less wind and weather exposure can result
in lowered operation and maintenance costs).
• The overall enhancement of your environment. It is preferable not to
place the spa under an unguttered roof overhang since run-off water
will shorten the life expectancy of the spa cover.
• For spas that are to rest on balconies, roofs or other platforms not
specically tied into main structural support, consult a professional
Structural Engineer with experience in this type of application.
• In the unlikely event that you should ever need to access or gain
entry to any portion of the spa for servicing, it is highly recommended
that you plan your outdoor installation to provide full access to the
entire spa. Please take this into consideration when placing the spa
in a deck or enclosed by a surrounding.
• Consider locating your spa away from any reective surface or glass
to prevent any damage to the synthetic skirt.
• Do not shim the spa. To ensure proper support the spa must sit at
on the intended foundation.
!
Page 16
Page 10
4.2 Indoor Location
For indoor installations many factors need to be considered before
installing a spa indoors.
WARNING: In addition to maintenance of lters and water
chemistry, proper ventilation is recommended to reduce the
risk of contracting a waterborne
illness (e.g. an infection, bac-
teria or virus) and/or respiratory ailments
that could be pres-
ent in the air or water. Consult a licensed architect or building
contractor to determine your specic needs if installing your
hot tub indoors.
!
• Proper Foundation: Consult a Structural Engineer when
considering a foundation that will adequately support the spa
the entire time it is in place. Proper support is critical especially
if the spa is to rest on a second story or higher. For spas that are
to rest on balconies, roofs or other platforms not specically tied
into the main structural support, you should consult a professional
Structural Engineer with experience in this type of application.
• Proper Drainage: It is extremely important to have in place
measures to sufciently handle excessive water spillage. Be
sure the ooring in which the spa rests on has adequate drainage
and can handle the entire contents of the spa. Be sure to make
provisions for ceilings and other structures that may be below the
spas installation. Areas around your spa can become wet or moist so
all ooring and subsequent furniture, walls and adjacent structures
should be able to withstand or resist water and moisture.
• Proper Ventilation: Proper ventilation should be discussed with
an Engineer or authority competent enough to understand the
necessary provisions needed to vent moist or heated air and air
associated with chemical odors outdoors. When the spa is in use
considerable amounts of moisture will escape, potentially causing
mold and mildew over time, which can damage certain surfaces and/
or surroundings.
• Sufcient Access: In the unlikely event that you should ever need
to access or gain entry to any portion of the spa for servicing, it is
highly recommended that you plan your indoor installation to provide
full access to the entire spa.
• Warranty: Damage caused by not following these guidelines or any
improper installation not in accordance to local codes or authorities is
not covered under the spas warranty. Please consult your local state
or city building ordinances.
• Do not shim the spa. To ensure proper support the spa must sit at
on the intended foundation.
Page 17
Page 11
4.3 Location for the ProLink™ Monitoring System
IMPORTANT! Choose an installation site with the front control
panel side pointing towards your home’s Wi-Fi router.
CAUTION: You must make sure that the spa control panel side
has a clear unobstructed line-of-site of the home Wi-Fi router. This
action ensures maximum signal strength between the spa and your
home’s Wi-Fi router.
Verify your home router’s Wi-Fi strength at the proposed spa location.
Front control panel side of spa must point towards your home’s Wi-Fi
router in your home as illustrated, Figure 4.3a. Stand near the proposed
front control panel side of the spa with your cell phone, then login to the
internet using your home Wi-Fi router signal (not 3G or 4G) and verify
results as follows:
If the home Wi-Fi router signal is strong (3-4 bars) and Internet access is
stable, the proposed installation site is a good choice.
If the home router’s Wi-Fi signal is weak and Internet access is slow or
produces an error, the proposed installation site is not a good choice.
• It may be necessary to choose another spa installation site.
• Relocate your home Wi-Fi router closer to the spa.
• Install a “repeater” device in the room closest to the spa to boost the
home’s router Wi-Fi signal at the proposed spa installation site.
Home WiFi
Router
J500
Welcome
Rev 1.0
Figure 4.3a
Page 18
Page 12
5.0 General Electrical Safety Instructions
Your new Jacuzzi® spa is equipped with the ProTouch™
system. It contains the most advanced safety and selfprotective equipment in the industry. Nonetheless, this spa
must be installed properly to ensure dependable usage.
Please contact your local Jacuzzi dealer or local building department
should you have any questions regarding your installation.
Proper grounding is extremely important. Jacuzzi spas are equipped
with a current collector system. A pressure wire connector is provided on
the surface of the control box, located inside the equipment door (page
15) to permit connection of a bonding wire between this point and any
ground metal equipment, metal water pipe or conduit within 5 feet (1.5m)
of the spa, or copper clad grounding rod buried within 5 feet (1.5m) of the
spa. Bonding wire must be at least No. 8 AWG (8.4 mm²) solid copper
wire. This is a most important safety assurance feature. Before installing
your spa, check with your local building department to ensure installation
conforms to local building codes.
6.0 Electrical Installation Instructions (240V
Service)
IMPORTANT NOTICE: The electrical wiring of this spa must
meet the requirements of the National Electrical Code/USA
(NEC) and any applicable state or local codes. The electrical circuit must
be installed by a qualied electrician and approved by a local building/
electrical inspection authority.
1.
!
DANGER: TO DECREASE THE RISK OF SHOCK,
PRODUCT DAMAGE OR ELECTRICAL FIRE.
This spa must be permanently connected (hard-wired) to the power
supply. No plug-in connections or extension cords are to be
used in conjunction with the operation of this spa. Supplying
power to the spa, which is not in accordance with these instructions,
will void both the independent testing agency listing and the
manufacturer’s warranty.
2. The power supplied to this spa must be a dedicated circuit with no
other appliances or lights sharing the power provided by the circuit.
3. To determine the current, voltage and wire size required, refer to
Section 7.0 “Power Requirements” (page 16) for your specic spa
model.
• Wire size must be appropriate per NEC and/or local codes.
• We recommend type THHN wire. All wiring must be copper to ensure
proper connections. Do not use aluminum wire.
• When using wire larger than #6 (10 mm²), add a junction box near
the spa and reduce to short lengths of #6 (10 mm²) wire to connect
to the spa.
Page 19
Page 13
4. The electrical supply for this product must include a suitably rated switch
or circuit breaker to open all ungrounded supply conductors to comply
with Section 422-20 of the National Electrical Code/USA, ANSI/NFPA
70. The disconnecting means must be readily accessible to the spa’s
occupant but installed at least 5 feet (1.5m) from spa water.
5. The electrical supply for this product must include a suitably rated
isolating switch and circuit breaker to comply with local electrical
regulations. This RCD/GFCI circuit breaker must be installed at the
power supply in the house electrical box.
6. The electrical circuit supplied for the spa must include a suitable
ground fault circuit interrupter (GFCI) as required by NEC Article
680-42/USA.
7. For Australia/ New Zealand, the spa should be supplied through
a residual current device (RCD) with a rated tripping current not
exceeding 30mA (IEC 60335-2-60).
8. To gain access to the spa’s power terminal block, you will need to
remove the corner and center cabinet panels.
9. Grab one of the corner panels, from the bottom, where it touches the
bottom pan. Then gently pull the panel forward to unsnap it from the
holding clip, Figure 6.0a. Place the corner panel in a safe location
to prevent from damaging it. Repeat the steps to remove the other
corner panel.
10. Now you need to remove the center panel. Grab the sides of the
panel and gently pull the cabinet forward until all the clips have been
release then pull up to remove, Figure 6.0b. Place the panel in a safe
location to prevent from damaging it.
11. Select the power supply entrance you want to use, Figure 6.0c.
Make sure to install a 3/4" electrical tting and conduit through the
large opening provided in the bottom of the control box so you can
feed the cable through to the terminal block.
12. Then remove the door screws for the access door on the control box
(Figure 6.0d).
13. Connect wires to the terminal block (Figures 6.0d-6.0e). ALL WIRES
MUST BE SECURELY CONNECTED or equipment damage could
result!
14. Install the control access box door and reinstall the cabinet side
panels.
Figure 6.0a
Equipment Area
Page 20
Page 14
Figure 6.0b
Equipment Area
Figure 6.0c
Equipment Area
9
9
7
8
2
3
1
5
10
11
6
12
12
PoweronLamp
on
DANGER!
TURN POWER
OFF! DO NOT
LOOK AT LIT BULB.
SEVERE EYE
DAMAGE OR BLINDNESS
CAN OCCUR!
4
13
Note: Equipment location (such as pumps, CLEARRAY system, stereo, drain, heater
etc.) varies by model.
1. ProTouch™ Glass Control
Panel
2. ProTouch™ Control Box
3. Heater
4. CLEARR AY Water
Purication System
5. QuickDrain™
6. Jets Pump
7. Filter/Circulation Pump
8. Jets Pump
9. Power Supply Entrance(s)
10. Spa Drain Valve
11. Pump Drain Plugs(s)
12. BLUEWAVE 2.0 Wireless Stereo
13. Jacuzzi ProLink™ Module
Figure 6.0d
Terminal Block Connection
F1 10A 250VAC
F7 30A
30A
F6
K12
K1
K9
K15
K14
T1
TB1
432
1
K5
J22
N/A
N/A
J43
J2
K13
J65
J51 J3
J52
J4
J61
J62
J49
K11
K10
J59
J44
J48
J39
2A 250VAC
F5
30A
F4
J28
J30
J27
J34
J29
J50
J56
J57
J63
J37
K8K4K6
K7
1/4AT 250VAC
F2
J16
J17
J18
ON
J1
J6
J9
J20
J21
J19 J67
J12
K3
J11
J13 J14
J15
J10
J24
ZONE 2
J25
ZONE 3
J23
ZONE 1
J26
ZONE 4
C58
C57
K2
GFCI
TRIP
J8
Q32
J60
J66
J55
J54
J38
J53
J45
J46
J47
J41
J58
J42
J31
J32
J33
J40
J64
J36
J35
1
2
3
4
S1
J7 J69J68
2 13
1. Main Terminal Block
2. Bonding Lug/Grounding
Terminal
3. Power wires Entrance
(Electrical tting and conduit
must be installed)
Page 21
Page 15
(Export 50Hz 230 VAC
Connection Shown)*
*Wire connections on circuit board must be changed, page 76.
Figure 6.0e
Terminal Connections
(North American 60Hz 240 VAC
Connection Shown)
BREAKER TERMINAL
CONNECTIONS
A
= Heater/Transformer
B
= Pump 2
C
= Pump 1/all other components
BREAKER TERMINAL
CONNECTIONS
A
= Heater/Transformer
B
= All other components
Red
Black
F1 10A 250VAC
F7 30A
30A
F6
K12
K1
K9
K15
K14
T1
TB1
432
1
K5
J22
N/A
N/A
J43
J2
K13
J65
J51 J3
J52
J4
J61
J62
J49
K11
K10
J59
J44
J48
J39
2A 250VAC
F5
30A
F4
J28
J30
J27
J34
J29
J50
J56
J57
J63
J37
K8K4K6
K7
1/4AT 250VAC
F2
J16
J17
J18
ON
J1
J6
J9
J20
J21
J19 J67
J12
K3
J11
J13 J14
J15
J10
J24
ZONE 2
J25
ZONE 3
J23
ZONE 1
J26
ZONE 4
C58
C57
K2
GFCI
TRIP
J8
Q32
J60
J66
J55
J54
J38
J53
J45
J46
J47
J41
J58
J42
J31
J32
J33
J40
J64
J36
J35
1
2
3
4
S1
J7 J69 J68
BREAKER TERMINAL
CONNECTIONS
A
= All components
SERVICE 1
SERVICE 2
SERVICE 3
Brn (L2)
Brn (L3)
Brn (L1)
Blu (N1)
Single Service
Dual Service
Three Phase Service
Blu
Brn
(N1)
(L1)
TB1
TB3
Green
A
SERVICE 1
SERVICE 2
Brn (L2)
Brn (L1)
Blu (N2)
Blu (N1)
Factory Default
SERVICE 1
Brn (L1)
Blu (N1)
Blu
BluBrn
Brn
Green
(L1)
(L2)
(N1)
(N2)
TB1
TB3
A
B
Blu
BrnBrn
Brn
Green
(L1)
(L2)
(N1)
(L3)
TB1
TB3
A
B C
Page 22
Page 16
7.0 Power Requirements
Jacuzzi® spas are designed to provide optimum performance and
exibility of use when connected to their maximum electrical service.
They are congured at the factory. The most common electrical
connections are listed below. Reference page 73 for dip switch
settings.
• All North American 60 Hz Models only: These models come set for
50A logic. If you prefer, your qualied technician can perform a logic
modication that allows the spas to operate on a different electrical
service.
North American Models (60 Hz)
Voltage: 240 VAC 240 VAC 240 VAC
Max. Current Draw: 32A 40A 48A
Frequency: 60 Hz 60 Hz 60 Hz
Number of Wires: 3 3 3
Circuit Breaker (2-Pole): 40A* 50A** 60A***
*
In 40A conguration, the heater will not operate while either jets
pump is running.
**
In 50A conguration, the heater will operate when one jets pump
is running, but will not operate while both jets pumps are running.
This is the factory setting.
***
In 60A conguration the heater will operate while both jets pumps
are running.
• All Export 50 Hz Models:
Export Models (50 Hz)
Single Breaker Single Breaker
Service 1
(including heater)*
Service 1
(including heater)**
Voltage: 230 VAC 230 VAC
Max. Current Draw: 17A 30A
Wattage: 3,9 kW 6,9 kW
Frequency: 50 Hz 50 Hz
Number of Wires: 3 3
*
In this conguration, the heater will not operate while either jets pump is
running. Only one jets pump will operate at a time.
**
In this conguration, the heater will operate while both jets pumps are
running.
Page 23
Page 17
Export Models (50 Hz)
Dual Service Breakers
Service1/Service 2**
Three Phase Service
Service1/Service 2/
Service 3***
Voltage: 230 VAC 230 VAC
Max. Current Draw: 12A/17A 12A/7A/10A
Wattage: 2,8kW/3,9 kW 2,8kW/1,6kW/2,3kW
Frequency: 50 Hz 50 Hz
Number of Wires: 5 5
**
In this conguration, the heater will operate while both jets pumps are
running. The Service 1 breaker will include connections for the heater
and transformer. The Service 2 breaker will have connections for all other
components. Note: 1x16A/20A is the factory setting.
***
In this conguration, the heater will operate while both jets pumps are
running. The Service 1 breaker will include the connection for the heater
and transformer. The Service 2 breaker (B) will have the connection for
jets pump 2. The Service 3 breaker (C) will have connections for jets pump
1 and all other components.
8.0 Spa Fill Up Procedure
For best results, read each step in its entirety before proceeding with this
procedure. Make sure all drains are closed before you begin, page 14.
1. Prepare The Spa For Filling
• Clear all debris from the spa. (Although the spa shell has been
polished at the factory, you may want to treat it with a specially
formulated spa cleaner.) Consult your authorized Jacuzzi dealer for
additional information prior to lling spa.
• Remove both ProClarity™ and ProClear™ Plus skimmer, polishing
lter lids and lters as illustrated in Section 13.1 (page 51).
2. Fill Spa
• Place the end of your garden hose into empty skimming lter tting
(on your left) as you stand next to the spa. Fill spa half way, then
place the garden hose into the opposite lter tting (on your right)
while adding the remaining ll water.
CAUTION: TO DECREASE BUILD UP ON COMPONENTS AND
MINIMIZE ACRYLIC DAMAGE.
Never ll with water from a water softener. If your water is
extremely “hard,” it is preferable to ll half-way with hard water and
the rest of the way with softened water. Water that is too soft can
be corrosive to metal components.
Page 24
Page 18
•
!
WARNING: TO DECREASE RISK OF INFECTION OR
DISEASE.
Fill hot tub with clean tap water from garden hose, to reduce risk of
contracting a waterborne
illness (e.g. an infection, bacteria or virus)
and/or respiratory ailments
. Fill until water covers all jets but does not
touch the bottom of the lowest headrest (DO NOT OVERFILL!).
IMPORTANT: Always ll your spa through both lter ttings after
draining. Failure to do so may cause air to be trapped in the pumps,
preventing them from circulating water. Remove the hose and
replace both lter cartridges as illustrated in Section 13.1 (page
51).
3. Turn On Power
Turn on power to spa at the home’s circuit breaker. The heater
and lter/circulation pump will automatically activate. If the screen
displays either a “Cool Warning” or “Freeze Protection” error, this is
normal. Normally, at the initial ll, the water tends to be cold. Refer to
page 66 for additional information.
4. Activate Jets Pumps
Turn on jet pumps when adding chemicals in step 5
(see Section 11.2, page 32 to activate jets).
5. Add Start-Up Chemicals
Add the spa water chemicals as recommended by your authorized
Jacuzzi spa dealer. See Section titled “Water Quality Maintenance”
(page 59) for general guidance.
WARNING: RISK OF POISONING OR DEATH.
Never leave chemicals opened and accessible to anyone. Use
chemicals according to the vendor’s instructions. Always store
chemicals in a safe and/or locked location. Keep away from
and out of reach of children.
!
6. Establish A Stable Sanitizer Reading
Establish a stable sanitizer reading of no less than 1.0 ppm free
chlorine or 2.0 ppm bromine. To ensure healthy water conditions,
always maintain a constant sanitizer reading within the levels
recommended on the inside cover of this manual. If sanitizer levels
cannot be stabilized, perform the decontamination procedure steps
1-7 on the following page.
Note: The “Decontamination Procedure” should also be used after the
spa has been “Winterized” (Sec. 13.8, page 58) or has been sitting
without power for an extended period.
1
Page 25
Page 19
7. Set Spa To Heat
To warm spa water to a comfortable temperature, follow these
steps:
• The display on the control panel displays the actual
temperature of the spa water. Tap or to increase or
decrease the water temperature in 1 degree increments.
• The heater will turn off 1 degree above set temperature and turn on 2
degrees below set temperature.
Note: The temperature range for the spa is 65 to 104°F (18.33 to 40°C).
To activate the Extended Temperature feature that allows the spa to
reach 106°F (41°C), see page 67.
Important Heater Details:
• The maximum temperature for which the spa can be set is 104°F
(40°C) and the minimum is 65°F (18.33°C).
• For North American spas: With a 50 amp service, turn off one
of the jet pumps to operate heater. With a 40 amp service, turn
off both jet pumps to operate heater. With a 60 amp service, the
heater will operate with both jet pumps on.
• Setting the thermostat at maximum will not accelerate the heating
process. This will only result in a higher ultimate temperature.
• The heater operates until the water reaches 1 degree above the
programmed “set temperature,” then turns off. The heater will
reactivate after the water cools to approximately 2 degrees below
the “set temperature.”
8. Place Cover On Spa
• Keeping the insulating cover in place anytime the spa is not in
use will reduce the time required for heating, thereby minimizing
operating costs.
• The time required for initial heat-up will vary depending on the
starting water temperature.
DANGER: RISK OF PERSONAL INJURY.
Check water temperature carefully before entering hot tub!
Excessive water temperature can cause burns, welts and
body temperature to rise, hyperthermia (over-heating).
!
Page 26
Page 20
Decontamination Procedure
Steps 1-7 below are only required when sanitizer levels are unstable
after performing Spa Fill Up Procedures steps 1-6. Disregard steps 1-7
below if sanitizer levels remain stable after performing steps 1-6 above
(refer to the inside cover of the manual).
1. Add 2.5 ounces of sodium dichlor for every 100 gallons of water.
Refer to the table below for approximate water ll volume by model.
CAUTION: RISK OF PERSONAL INJURY OR SPA DAMAGE!
Never add chlorine tablets (trichlor) or acid to your hot tub for
any reason! These chemicals may damage components within
your hot tub, burn or irritate your skin, create a rash, and void
the manufacturer warranty for your spa.
!
Water Fill Volume by Model
Average Sodium
Model Fill Volume* Dichlor
J-575................................445 Gal (1,685 L) ................................ 11.0 oz
J-585................................440 Gal (1,666 L) ................................ 11.0 oz
*Use average ll volume for chemical maintenance
2. Leave spa cover open during this step to allow
excessive chemical vapors to exit spa, protecting pillows
and plastic knobs from chemical attack. If spa is indoors,
open doors and windows for proper ventilation. Turn on
all spa jet pumps for 1 hour, open all air controls, and
place all massage selector knob(s) in their center “combo” position.
Note: You will need to activate the jet pumps every 20 minutes since
these functions have an automatic 20-minute time-out that turns them off.
WARNING: RISK OF PERSONAL INJURY!
• To decrease the risk of injury, drowning or entrapment,
never leave your hot tub unattended for any reason while
the cover is open and accessible, especially to small children and animals!
• Precautions should be taken to minimize your exposure
to chemical vapors (that could cause lung, brain, or skin
damage).
!
3. Turn off power to the spa at the circuit breaker, then drain tub as
outlined in Section 13.2 (page 55).
4. Rell spa with clean tap water from garden hose until water covers
all jets but does not touch the bottom of the lowest headrest with all
headrests in their lowest position (DO NOT OVERFILL!)
Page 27
Page 21
CAUTION: TO DECREASE BUILD UP ON COMPONENTS AND
MINIMIZE ACRYLIC DAMAGE.
Never ll with water from a water softener. If your water is extremely
“hard,” it is preferable to ll halfway with hard water and the rest of
the way with softened water. Water that is too soft can be corrosive
to metal components.
5. Consult your authorized Jacuzzi dealer for chemical
recommendations, then add chemicals to hot tub water to achieve
a constant sanitizer reading within the levels recommended on the
inside cover of this manual.
6. Turn on jet pumps when adding chemicals to ensure proper mixing
and leave your hot tub cover open until the sanitizer level becomes
stable to protect pillows and plastic knobs from chemical attack.
Refer to the inside cover of the manual.
WARNING: RISK OF PERSONAL INJURY.
• To decrease the risk of injury, entrapment or drowning,
never leave your hot tub unattended for any reason while
the cover is open and accessible to small children and
animals!
• To decrease the possibility of contracting a waterborne
ill-
ness (e.g. an infection, bacteria or virus) and/or respiratory
ailments, maintain water chemistry within step 6 parameters. If you or other bathers experience such a condition,
discontinue use and seek medical attention.
!
7. Establish a sanitizer reading no less than 1.0 ppm free chlorine
or 2.0 ppm bromine, then allow the hot tub to set undisturbed for
8 hours. Retest water after 8 hours to determine if sanitizer levels
are stable. If sanitizer levels are stable, your spa is ready for use.
To ensure healthy water conditions, always maintain a constant
sanitizer reading within the levels recommended on the inside cover
of this manual. If sanitizer levels are not stable at this time, it will be
necessary to repeat this procedure in its entirety until stable sanitizer
readings are achieved.
IMPORTANT: If the CLEARR AY® water purication system is removed
from the hot tub or is not operating effectively follow the “without
CLEARRAY ®” water chemistry parameters as dened by the Association
of Pool and Spa Professionals.
8. After adequate sanitizer levels are achieved, close all spa air controls
to maximize heat retention when spa is not in use.
Page 28
Page 22
9.0 Spa Features
9.1 J-575 Spa Features
3
3
7
7
4
4
8
8
8
9
8
11
11
11
11
11
14
14
12
17
13
10
16
16
16
17
6
5
5
5
5
2
2
22
19
22
20
15
15
15
15
18
1
21
21 21
21
1. Control Panel
2. Air Control Valves (4 ea.)
Introduce Air to Specied Jet
Groups
3. Waterfall Control Valve (2 ea.)
4. Massage Selectors (2 ea.)
Controls Specied Jet Groups)
5. Pillows
6. Filter/Skimmer Grill
7. Waterfalls (2 ea.)
8. Suction Covers (4 ea.)
9. Underwater Light
10. NX Jets (2 ea.)
11. FX Spinner Jets (14 ea.)
12. FX Jets (6 ea.)
13. RX Jets (6 ea.)
14. FX Directional Jets (2 ea.)
15. PX Jets (8 ea.)
16. FX2-S Jets (6 ea.)
17. MX2 Jets (5 ea.)
18. Gravity Drain/Heater Input/
CLEARRAY Return Fitting
19. Interior Perimeter Lighting
20. Waterfall Filtration Return
21. Optional Audio System
Speakers (4 ea.)
22. Optional BLUEWAVE 2.0
Wireless Stereo Audio System
(located behind cabinet panel)
Spa features subject to change without notice
Page 29
Page 23
Spa operation subject to change without notice
9.2 J-575 Massage/Waterfall Selector Diagram
1
4
4
a b
5
a
b
2
1a
1a
1b
1b
2a
2a
2a
2b
2b
2b
2b
3
3
Massage Selectors (1-2)
• Massage selector 1 diverts jets pump 1 output between jets groups
1a-1b.
• Massage selector 2 diverts jets pump 2 output between jets groups
2a-2b.
Waterfall Selectors (3-4)
• Waterfall selector (3) controls circulation pump output to waterfall (3).
• Waterfall selector (4) controls circulation pump output to waterfall (4).
Jets Without Massage Selector Controls (5)
• Jets (5) are always on when jets pump 1 is running.
Page 30
Page 24
9.3 J-575 Air Controls Diagram
Air Controls Operation
• Toggle air controls 1-4 to add air to designated jet groups.
1 4
3
2
1
1
1
4
4
4
4
3
3
3
2
2
Spa operation subject to change without notice
Page 31
Page 25
9.4 J-585 Spa Features
3
3
7
7
4
4
22
8
8
8
9
8
10
10
13
13
11
10
11
12
12
15
15
15
15
16
16
19
6
5
5
5
5
2
2
2
2
18
20
14
14
17
1
21
21 21
21
Spa features subject to change without notice
1. Control Panel
2. Air Control Valves (4 ea)
Introduce Air to Specied Jet
Groups
3. Waterfall Control Valve
4. Massage Selectors (2 ea.)
Controls Specied Jet Groups)
5. Pillows
6. Filter/Skimmer Grill
7. Waterfalls (2 ea.)
8. Suction Covers (4 ea.)
9. Underwater Light
11. FX Spinner Jets (10 ea.)
12. FX Jets (8 ea.)
13. RX Jets (8 ea.)
14. FX Directional Jets (2 ea.)
15. PX Jets (2 ea.)
16. FX Small Jets (8 ea.)
17. FX2S Jets (5 ea.)
18. MX2 Jets (3 ea.)
19. Interior Perimeter Lighting
20. Gravity Drain/Heater Input/
CLEARRAY Return Fitting
21. Waterfall Filtration Return
22. Optional Audio System
Speakers (4 ea.)
23. Optional BLUEWAVE 2.0
Wireless Stereo Audio System
(located behind cabinet panel)
Page 32
Page 26
9.5 J-585 Massage/Waterfall Selector Diagram
1
3
3
4
4
a b
5
a
b
2
1a
1a
1b
2b
2b
2b
2b
2a
2a
Massage Selectors (1-2)
• Massage selector 1 diverts jets pump 1 output between jet groups
1a-1b.
• Massage selector 2 diverts jets pump 2 output between jet groups
2a-2b.
Waterfall Selectors (3-4)
• Waterfall selector (3) controls circulation pump output to waterfall (3).
• Waterfall selector (4) controls circulation pump output to waterfall (4).
Jets Without Massage Selector Controls (5)
• Jets (5) are always on when jets pump 1 is running.
Spa operation subject to change without notice
Page 33
Page 27
Spa operation subject to change without notice
9.6 J-585 Air Controls Diagram
1 4
3
2
1
1
4
4
3
3
3
3
2
2
Air Controls Operation
• Toggle air controls 1-4 to add air to designated jet groups.
Page 34
Page 28
10.0 Registration and Start-up
10.1 Start-up Sequence
During the start-up sequence, the welcome screens will appear, Figure
10.1a. Then a blow out cycle will begin, page 43. After the cycle ends,
the hot tub will either display the Registration Menu or the Home Menu.
Note: The start-up menu will time out after approximately 3 seconds.
10.2 Register Your New Spa
Registering your spa is important in order to validate your warranty, page
29. In order to register you will need to have the spa serial number,
Figure 10.2b, then you will need to register online in order to receive a
passcode (not applicable to export models). A passcode is only given
for North American models only. The passcode must be entered on the
control panel in order to unlock the Registration Lockout screen, Figure
10.2c.
If this option is skipped (North American models only), you will be able
to activate components, but, after 10 minutes, the screen will revert
back to the registration screen. This process will continue until the spa is
registered and the passcode is entered.
Note: The spa will still protect itself if an error is detected.
Figure 10.1a
Welcome
Rev 1.0
Figure 10.2a
Please register your spa at:
www.jacuzzi.com
Once registered, enter your spa serial # and
registration passcode here:
Reminder
enter #
later
Page 35
Page 29
To register your spa you need to have
your spa serial number. The best time
to retrieve the serial number is when the
spa is being connected. You must
register your spa via the internet at
www.Jacuzzi.com.
Follow these steps to register your spa.
1. Using your home computer or other
device, connect to the internet.
2. Go to www.Jacuzzi.com website to register your spa.
3. Click Outdoor Hot Tubs
4. Click For Owners
5. Click Warranty and Manuals
6. Click Warranty Registration
7. Enter your serial number.
8. Once registered you will be given a passcode that will need to be
entered into the control panel (North American models only).
Keep a record of your serial number and passcode for any future
reference. Write that information below.
Serial Number:
Passcode:
After registering your spa online, you can
then enter the registration information into
the control panel.
Note: If a number is entered wrong you can
tap X to move backward.
1. From the registration screen, Figure
10.2a, tap
enter #
to enter the spa
serial number.
2. Input the 9-digit serial number, Figure
10.2c. Use the letters A, D or R if your
serial number begins with a letter.
3. Tap
Set
to enter the information and
proceed to enter the passcode.
4. Now input the 9-digit passcode, Figure
10.2d, that was provided online when you registered
your spa.
5. Tap
Set
to enter the information.
serial
nameplate
PoweronLamp
on
DANGER!
TURN POWER
OFF! DO NOT
LOOK AT LIT BULB.
SEVERE EYE
DAMAGE OR BLINDNESS
CAN OCCUR!
Figure 10.2b
Enter Spa Serial #
321
654
9
A
D
R
0
87
set
X
Enter Passcode #
set
X
321
654
9
A
D
R
0
87
Figure 10.2c
Figure 10.2d
Page 36
Page 30
10.3 ProTouch™ Glass Control Panel
Your Jacuzzi Spa is equipped with a state-of-the-art touch screen control
panel. The control panel complements the contemporary and sleek
design of your spa. Access to all menus can be achieved by using the
touch screen. Programming features can be easily programmed with our
user-friendly design. With the ease of use, there will more time to enjoy
the benets of your spa.
A. Home Menu Control Buttons
The Home Menu, Figure 10.3a, provides access to spa functions and
programming. Operation is made easy by the interactive touch-screen
control panel. If there is no activity for 5 minutes, the LCD display will
time-out into a sleep mode. To reactivate the display, just swipe across
the top from one corner to the other, Figure 10.3b.
NOTE: When a feature is on, the button will have a blue highlight around it.
= Temperature Control: Allows you to adjust the set
temperature of the spa:
• Increase the temperature by tapping
in 1° increments.
• Decrease the temperature by tapping in 1° increments.
Note: The temperature range for the spa is 65 to 104°F (18.33 to 40°C).
To activate the Extended Temperature feature that allows the spa to
reach 106°F (41°C), see page 67.
= Jet Button: Tap to access the menu to operate the jets pump,
page 32.
= Light Button: Tap to access the menu to operate the various
lighting options, page 33.
= Music Button: Tap to access the menu to operate the audio
system and settings, page 35.
Note: If the spa does not have the stereo option, there will not be a
button on the control panel.
= CLEARRAY Button: Tap to activate the CLEARRAY on
demand feature, page 38.
96
6:45 PMON UV
Figure 10.3a
Figure 10.3b
Page 37
Page 31
= Error Indicator Icon: Displays when there is error message
that needs to be addressed. The icon will also appear under
the Temperature reading as a reminder, page 65.
= Invert Button: Tap to invert the display image.
= Settings Button: Tap to access the programming and setting
menus, page 40.
B. Status Bar
The status bar, Figure 10.3c, is located at the top of the Home Screen
menu. When certain components, features or programs are on, their
icons are represented within the Status Bar.
= Heater/Filter Icon: The current programmed heater/
lter setting will appear on the status bar to indicate
what heat mode is enabled, page 41.
= Lock Icon: Displays when one of the lock modes is
enabled, page 46.
= Heat ON Icon: Displays whenever the heater is on and
heating the water, page 41.
= CLEARRAY ON Icon: Displays when the CLEARRAY
system is enabled, page 38.
= Error Indicator Icon: Displays when there is error
message that needs to be addressed. The icon will
also appear under the Temperature reading as a
reminder, page 65.
= Wi-Fi Icon: Displays when there is a Wi-Fi connection
to the home router.
= Time Indicator: The time will always be shown when
the Home Menu is displayed. The appearance will vary
depending on whether the clock is set to a 12-Hour or
24-Hour conguration, page 48. The default setting
is 12-Hour.
Note: The time does NOT automatically adjust for daylight saving time.
The time must be manually adjusted.
Figure 10.3c
6:45 PMON UV
AUTO
ON
UV
6:45 PM
Page 38
Page 32
11.0 Operating Instructions
11.1 ProTouch™ Glass Control Panel
Your Jacuzzi spa is equipped with a ProTouch Glass control panel;
massage selectors, and air control knobs located on the top rim of the
spa (pages 22-27). These controls let you operate many of the
special functions of your Jacuzzi spa.
11.2 Activating the Jets Pumps
From the Home Menu, (Figure 11.2a), tap to enter the Jets Pump
Submenu. The LCD screen will display the Jets Pump Submenu (Figure
11.2b).
Note: Once you enter the Jets Pump Submenu, all the pumps will
activate. You can turn off the jets pump by tapping the jet button 1 or 2.
1 2
JETS
96
6:45 PMON UV
= Jets Pump 1 Button
= Jets Pump 2 Button
= Back Button: Tap to go back to the previous menu.
= Invert Button: Tap to invert the display image.
= Setting Button: Tap to access the programming and setting
menus, page 40.
1. Tap the Jets 1 button to turn the pump #1 on and
off.
2. Tap the Jets 2 button to turn the pump #2 on and
off.
Note: When a jets pump is on, the button will
have a blue highlight.
Auto Turn Off — Anytime a pump has been manually turned on, it will
automatically turn off after approximately 20 minutes. If at this time you
desire more jet operation you may simply turn the pump(s) back on.
Figure 11.2a
Figure 11.2b
1
B
JETS ICON
WHEN OFF
JETS ICON
WHEN ON
1 2
Page 39
Page 33
11.3 Lights Menu
From the Home Menu, (Figure 11.3a), tap to enter the Light
submenus. The LCD screen will display the Light Submenu (Figure
11.3b). From this menu you can control the interior lighting, exterior
lighting and experience effect. When you tap to enter the submenus,
the lights will turn on, if not on already.
Note: The lights automatically turn off after 2 hours. They can be
reactivated if needed.
Interior
>
= Interior Lights Selection: Tap > to enter the
Interior Lights Menu.
Exterior
= Exterior Lights Selection: Tap to change
the intensity of the Exterior Lights.
Experience
>
= Experience Mode Selection: Tap > to enter the
Experience Mode Menu.
= Back Button: Tap to go back to the previous menu.
= Invert Button: Tap to invert the display image.
= Setting Button: Tap to access the programming and setting
menus, page 40.
11.4 Interior Lights
The interior lights consist of the waterfall
lighting, above (perimeter lighting) and
under (footwell lighting), Figure 11.4a.
Each can be independently controlled or
they can be controlled in unison. You can
control 3 aspects of the interior lights.
Tap > or > to scroll through the selections for “Waterfall,”
“Above,” “Under” and “All.” If you choose the “All” option, then the lights
will work in unison and display the same features and colors.
LIGHTS
Interior
Exterior
Experience
>
>
96
6:45 PMON UV
Figure 11.3a
Figure 11.3b
B
Interior
5
waterfall
>
>
bright
speed
Figure 11.4a
Page 40
Page 34
A. To control the intensity of the interior lights follow the steps
below.
1. The “Bright” feature controls the intensity of the interior
lights. Use or to select your intensity level. The
levels range from 5 to 0, as follows: 5 = 100%,
4 = 80%, 3 = 60%, 2 = 40%, 1 = 20% and 0 = 0%.
Note: The default intensity level is 3.
2. This feature is available for the following selections: “Waterfall,”
“Above,” “Under” and “All.”
B. To control the speed of the interior lights follow the steps below.
1. The “Speed” feature controls the speed of the color
blending, measured in seconds. Use or to
select speed rotation. The levels range from 5 to 0, as
follows: 5 = 5 secs, 4 = 10 secs, 3 = 15 secs,
2 = 30 secs, 1 = 60 secs and 0 = single color.
Note: The default speed interval is 0.
2. This feature is available for the following selections: “Waterfall,”
“Above,” “Under” and “All.”
C. To select a solid color for the interior lights follow the steps
below.
1. To make a selection tap the color block on the
display. Colors available are White, Blue, Green,
Yellow, Orange, Red, and Pink.
Note: The default color will always be the last color used.
2. This feature is available for the following selections: “Waterfall,”
“Above,” “Under” and “All.”
11.5 Exterior Lights
The exterior corner lighting has 4 settings
(Figure 11.5a). The lights display a solid
White color only. By continually tapping
you will scroll through the following:
1. OFF: Exterior lights are turned off.
2. MID: Solid White color with a 50% intensity level.
3. ON: Solid White color with a 100% intensity level.
4. AUTO: Solid White color with a 100% intensity
level. Lights are on from 7:00 pm to 12:00 am.
Note: “AUTO” is the default setting.
bright
Figure 11.4b
speed
Figure 11.4c
Figure 11.4d
LIGHTS
Interior
Exterior
Experience
>
>
Figure 11.5a
Page 41
Page 35
11.6 Experience
The lighting experience can be user
enhanced by activating one of the settings
below. Just tap one of the words (Quiet,
Fun, Glow or Joy) to start the experience,
(Figure 11.6a). The default setting is “Glow.”
1. Quiet: All interior lights are a solid Blue
color with a 20% intensity level.
2. Fun: All interior lights cycle through all colors with a 100% intensity
level and speed of 5.
3. Glow: All interior lights are a solid White color with a 100% intensity
level.
4. Joy: All interior lights cycle through all colors with an 80% intensity
level and speed of 3.
11.7 Music Menu
Models equipped with the optional Audio System offer an enhanced spa
experience. The BLUEWAVE 2.0 Wireless Audio System works with most
Bluetooth wireless devices. An auxiliary device can be connected, via a
3.5 mm plug cable, located behind the front cabinet panel, if a Bluetooth
device is not available. These models also include four high delity spa
engineered speakers for unsurpassed sound quality and long-life, and an
integrated powered subwoofer for a superb acoustical sound.
Note: If the spa does not have the stereo option, there will not be a
button on the control panel.
To access the Music Menu, tap , Figure 11.7a. The display will
change to Figure 11.7b. Once you enter the Music Menu, tap the power
button to turn the stereo on. Your connected electronic device, Bluetooth
or auxiliary, provides the audio entertainment.
WARNING: RISK OF ELECTRICAL SHOCK HAZARD
EXISTS AND EQUIPMENT DAMAGE! Never install or
remove electrical devices while hands are wet or while sitting
partially immersed or fully immersed in spa!
96
6:45 PMON UV
Artist
Track name
MUSIC
BT AUX
= Power Button: Tap to turn the stereo on and off.
= Bluetooth Settings: Tap to use your Bluetooth device with
the stereo.
LIGHTS
Experience
quiet
glow joy
fun
Figure 11.6a
Figure 11.7a
Figure 11.7b
BT
Page 42
Page 36
= Auxiliary Settings: Tap to use your auxiliary device with
the stereo. This is the default setting.
= Audio Settings: Tap to access the audio submenu.
= Forward: Tap to advance forward through tracks.
= Rewind: Tap to move back through tracks.
= Pause/Play: Tap to pause and play tracks.
= Volume Slider: Slide from side to side to increase and
decrease the volume level.
Artist
Track Name
= Artist Track: Will display the artist and track information,
if it is available. If the information is not available this part
will be blank. If the information provided is too long, the
maximum number of characters will be display follow by
dots (“...”).
= Back Button: Tap to go back to the previous menu.
= Invert Button: Tap to invert the display image.
= Setting Button: Tap to access the programming and setting
menus, page 40.
If you experience a connection problem with your Bluetooth device, make
sure that the Bluetooth antenna is secure and located at the highest point
within the equipment bay.
11.8 Bluetooth® Pairing Instructions
To pair your Bluetooth® device to the BLUEWAVE®, follow these steps:
1. Tap the music icon on the control panel screen then touch the power
button located on the top right to turn on the stereo.
2. From your Bluetooth device, make sure that the Bluetooth setting is
ON.
3. Follow the pairing instructions for your Bluetooth device and connect
to “BLUEWAVE®” device that appears on your screen.
4. If asked for a password, enter the password “0000” and then
connect.
5. If the pairing process is successful, your Bluetooth device will show
“Connected” right next to “BLUEWAVE®”.
6. Once the connection is established, Bluetooth “BT” icon on the
screen will be highlighted conrming the connection.
Note: The BT icon cannot be selected manually; a Bluetooth connection
must be established with your device.
AUX
or
B
Page 43
Page 37
11.9 Audio Settings Menu
To enter the Audio Settings Menu, tap from the Music submenu,
Figure 11.9a. The display will change to Figure 11.9b. The Audio Settings
menu offers an enhanced audio experience by providing a custom or
preset bass and treble settings.
Bass
Treble
Audio +
ClassicalRock Pop
Artist
Track name
MUSIC
BT AUX
= Level Adjustment Bars: Indicates the adjustment level by
the number of bars lled.
= Bass Adjustment: Slide from side to side to adjust the
Bass range from -5 to 5. This feature can be used to create
a custom sound.
= Treble Adjustment: Slide from side to side to adjust the
Treble range from -5 to 5. This feature can be used to
create a custom sound.
= Rock Preset: Tap
Rock
to activate the “Rock” music audio
setting. “Rock” has a 1 Bass and 3 Treble preset setting.
When not in use it will be grayed out; if it is in use the button
will be highlighted, Figure 11.9b.
= Classical Preset: Tap
Classical
to activate the “Classical”
music audio setting. “Classical” has a 1 Bass and 1 Treble
preset setting. When not in use it will be grayed out; if it is in
use the button will be highlighted, Figure 11.9b.
= Pop Preset: Tap
Pop
to activate the “Pop” music audio
setting. “Pop” has a -1 Bass and -2 Treble preset setting.
When not in use it will be grayed out; if it is in use the button
will be highlighted, Figure 11.9b.
= Back Button: Tap to go back to the previous menu.
= Invert Button: Tap to invert the display image.
= Setting Button: Tap to access the programming and setting
menus, page 40.
Figure 11.9a
Figure 11.9b
Bass
Treble
Rock
Classical
Pop
B
Page 44
Page 38
11.10 CLEARRAY on Demand
The CLEARRAY on demand feature
activates the water purication system
for a period of 1-hour. Tap to turn
the system on. During this time the
circulation pump and the CLEARRAY
unit are on. The button will have a blue
highlight when this feature is on.
Note: When the CLEARRAY system is
on due to a programmed or scheduled setting
the feature cannot be turned off.
11.11 Adjusting Jet Flow
The water ow to certain jets in your spa can be increased or
decreased by rotating the outside jet face.
Note: Always keep at least 6 adjustable jets open at all times.
11.12 Adjusting PowerPro™ MX2 Jets
Tilt PowerPro MX2 Jet nozzle to angle of choice as desired.
Rotate nozzle clockwise to reduce ow volume from jet or
rotate counterclockwise to increase ow volume.
Note: Always keep at least 6 adjustable jets open at all
times.
11.13 Adjusting RX Jets
Rotate the outside jet face clockwise to decrease or
shut off water ow. Turn counterclockwise to turn on or
increase water ow.
Note: Always keep at least 6 adjustable jets open at all times.
11.14 Waterfall Control
Turn waterfall control valve (pages 22-27) from side to side to
increase output, decrease output or turn off the waterfalls.
Note: When the waterfall is in the OFF position, some water
may still ow through. This is considered normal.
11.15 Air Controls
Certain jet systems have their own air control. Each control
introduces air into the water lines that supply that specic jet
group (pages 22-27). Simply press any air control button, Jacuzzi
logo side down, to open or press the opposite side to button to close. To
minimize heat loss, all air controls should be closed when the spa is not
in use.
Note: Certain jets may draw air even though they are closed. This is
considered normal.
96
6:45 PMON UV
Page 45
Page 39
11.16 Selecting the Desired Massage Action
Your Jacuzzi spa is equipped to allow you to customize
the massage action you desire. Each model incorporates a
massage selector that allows you to customize the massage
and performance by diverting water between various jet
systems. Simply turn the massage selector to divert water pressure to
various jet groups.
Note: It is considered normal for sound levels within the valve to vary
between positions due to the large amounts of water owing through
it. For optimum ltration benets, leave the valve in the center position
when the spa is covered.
11.17 Optional BLUEWAVE® 2.0 Wireless Audio System
Jacuzzi models equipped with the optional audio system offer enhanced
hot tub enjoyment with an integrated state-of-the-art audio system. These
models include an integrated Auxiliary or Bluetooth player receiver,
high-quality spa engineered speakers for unsurpassed sound quality
and long-life, and a powered subwoofer for an enhanced acoustical
experience.
Page 46
Page 40
12.0 Programming Instructions
Your Jacuzzi spa is equipped with setting menus that allow you to pro-
gram and activate different components of the spa. With our ProTouch™
Glass control panel, programming your spa has never been easier. In the
sections that follow, we will guide you through the process of program-
ming the spa to t your personal comfort.
Water Care
WiFi
Heat & Filter
SETTINGS
>
>
>
96
6:45 PMON UV
Heat & Filter
= Heat and Filter: Tap > to access the heating and
ltration programming, page 41.
Water Care
= Water Care: Tap > to access the water care
programming, page 44.
Lock
= Lock: Tap > to access the locking programming, page
46.
Time & Date
= Time and Date: Tap > to access the time and date
programming, page 48.
Language
= Language: Tap > access the language programming,
page 48.
Units
= Units: Tap either
Fº
or
Cº
for the temperature
display. Default setting is
Fº
.
WiFi
= Wi-Fi: Tap > to access the Wi-Fi programming, page
49.
= Back Button: Tap to go back to the previous menu.
= Invert Button: Tap to invert the display image.
Figure 12.0b
Figure 12.0a
B
Page 47
Page 41
12.1 Programming the Heating Mode
Your Jacuzzi spa is equipped with 3 modes of heating, Figure 12.1a. An
automatic mode called “Auto,” where the spa’s temperature is maintained
at all times. An energy saving heating cycle called “Econo.” A mode that
will only activate the heater during the daytime called “Day” mode.
Note: The heater will activate when the temperature drops 2° from the
set temperature.
Indicates that the feature is active. Indicates that the feature is not
active.
A. Auto heating:
1. When programmed to “Auto,” the spa
will maintain the water temperature to
the set temperature. Heating will occur
when necessary.
2. To select this mode, tap next to the
“Auto” icon.
B. Econo heating:
1. This is an energy saving heating program that allows the spa to heat
during non-peak hours. When programmed to “Econo,” the spa will
only be allowed to heat the water between 5:00 PM to 7:00 AM every
day of the week. The hours cannot be adjusted.
2. To select this mode, tap next to the “Econo” icon.
C. Day heating:
1. When programmed to “Day,” the spa will only be allowed to heat the
water between 7:00 AM to 5:00 PM every day of the week. The hours
cannot be adjusted.
2. To select this mode, tap next to the “Day” icon.
12.2 Programming the Primary Filter
To access the “Primary Filter” feature, you need to use the Slider Bar to
scroll down to the “Heat & Filter” menu, Figure 12.2a and 12.2b. Once
you scroll down, tap > to enter the “Primary Filter” programming, Figure
12.2c.
Econo
Day
Auto
HEAT & FILTER
Figure 12.1a
Figure 12.2a
Figure 12.2b
Econo
Day
Auto
HEAT & FILTER
Primary Filter
Secondary Filter
HEAT & FILTER
>
>
Page 48
Page 42
During a primary ltration, the circulation pump, CLEARRAY and ozone
unit (if applicable) are activated. The factory default cycle starts at 12:00
AM and last for 8 hours. If you elect to keep this setting, then you can
skip this section.
In extreme bitter cold weather we recommend you program
the circulation pump to run 24 hours. Refer to the "Winterizing"
section on page 58.
Any time the circulation pump runs outside of a program cycle, e.g. for
heating, that run time will be deducted from the next primary lter cycle.
For example, the primary lter cycle is set to 8 hours every 24 hours but
the circulation pump comes on for 2 hours to heat the water after the
cycle has nished. The next primary lter cycle will only be for 6 hours
not 8 hours.
A. To change the default cycle (the
adjustments are made in 1-hour
increments):
1. Tap
Start
to program the start time for
the cycle.
2. Slide your nger up and down to roll
the time scroll wheels to adjust the start
time.
3. Tap
End
to program the end time for the cycle.
4. Slide your nger up and down to roll the time
scroll wheels to adjust the end time.
5. Tap
Set
to save and accept the changes.
Summer Logic: In warm weather, the water temperature in the spa
may exceed the set temperature. This condition may occur due to
heat transference from the lter/circulation pump and jets pumps.
If the water temperature is higher than 95°F (35°C) and rises two
degrees above the set temperature, a “Summer Logic” condition
occurs that deactivates the lter/circulation pump and CLEARRAY ®.
This safety feature cannot be altered! The lter/circulation pump and
CLEARRAY ® will remain off until the water temperature cools to the
set temperature (except between 9am-11am when the lter/circulation
pump runs for it’s mandatory 2 hour cycle.) To help prevent a “Summer
Logic” condition, it may be necessary to reduce lter/circulation pump
cycles run times in warm weather.
Primary Filter
12:00
Start
Set
8 00
8:00
End
pm
Figure 12.2c
Page 49
Page 43
12.3 Programming the Secondary Filter
To enter the Secondary Filter program,
tap > from the heat and lter menu, Figure
12.2b. The display will change to Figure
12.3a. During a secondary ltration, the Jets
Pump 1 is activated. There are 3 cycles you
can select from, Figure 12.3a. The factory
default cycle is “Away Mode.” If you elect to
keep this setting, then you can skip this section.
Indicates that the feature is active. Indicates that the feature is
not active.
A. To change the Secondary Filter cycle:
1. Away Mode: Secondary Filtration is disabled. To activate this mode,
tap next to the “Away” icon.
Note: This is the factory default setting.
2. Infrequent Mode: Activates two cycles at 8:00 PM and 8:00AM
every other day. Each cycle will last 10 minutes for a total of 20
minutes every other day. To activate this mode, tap next to the
“Infrequent” icon. Time and duration cannot be altered.
3. Frequent Mode: Activates two cycles at 8:00 PM and 8:00AM every
day. Each cycle will last 10 minutes for a total of 20 minutes every
day. To activate this mode, tap next to the “Frequent” icon. Time
and duration cannot be altered.
12.4 Cleaup Cycle
The cleanup cycle occurs once per day at 12:00 pm (noon) for two
minutes. This is not user programmable. The Jets Pump 1 and the
Circulation Pump will turn on for one minute and then shut off. Then Jets
Pump 2 will turn on and run for 1 minute then shut off. Turning off the
corresponding jets pump that is running can deactivate the feature.
12.5 Blow-Out Cycle
This cycle will purge the air from the plumbing lines normally caused by
draining and lling the spa. The Jets Pump 1 and the Circulation Pump
will turn on for 1 minute and then shut off. Then Jets Pump 2 will turn
on and run for 1 minute then shut off. Turning off the corresponding jets
pump that is running can deactivate the feature. This cycle will only
occur:
• At start up.
• After exiting a service lock.
Secondary Filter
Away
Infrequent
Frequent
Figure 12.3a
Page 50
Page 44
12.6 Water Care Programming
Water care is crucial to maintaining a healthy and clean spa. The
CLEARRAY water purication system leads the way by sanitizing the
water using a UV light bulb. Your spa can be programmed to remind you
when to check and replace certain components.
From the “Settings” menu, tap > next to “Water Care” to enter the
programming options, Figures 12.6a and 12.6b.
A. Programming the CLEARRAY UV Bulb Timer
The CLEARRAY UV bulb has a life expectancy of 1-year. A timer
activates when power is applied and begins a countdown starting at
365 days. Once the timer expires, an error message will appear of the
display, the UV bulb must be replaced and the timer needs to be reset.
1. When you enter the “Water Care” Menu,
Figure 12.6c, you will able to set the
CLEARRAY UV bulb timer.
2. Slide your nger up and down to roll
the days scroll wheel to adjust the
number of days from OFF to 365. The
adjustments are made in increments
of 10 days. The CLEARRAY UV timer
counts down by days not usage. The days are stored
in memory if the power is interrupted.
Note: It is not recommended that this feature be turned OFF. In order to
continually have the CLEARRAY system effectively preform its function,
it should be program as instructed.
3. Tap
Set
to conrm and save your changes.
4. When the timer expires, a message will appear on the control panel
display, page 67. The CLEARRAY UV bulb must be replaced
(page 62) and the timer must be reset. Tap “reset” and follow the
instructions above to reset the timer. If you tap “snooze” the message
will clear but the error icon will display and the reminder screen
will reappear in 10 days.
Water Care
WiFi
Heat & Filter
SETTINGS
>
>
>
Water Care
set to
365
0 days
CLEARRAY
>
Set
>
Figure 12.6a
Figure 12.6b
Water Care
set to
365
0 days
Set
>
CLEARRAY
>
Figure 12.6c
Page 51
Page 45
B. Programming the ProClarity/ProClear Filter Timer
A programmable lter timer can be set to remind you when to clean or
replace the lters and skimmer bag.
1. When you enter the “Water Care”
Menu, Figure 12.6c, tap > or > until you
reach the “ProClarity” option, Figure
12.6d.
2. Slide your nger up and down to roll
the days scroll wheel to adjust the
number of days from OFF to 180. The
adjustments are made in increments of 10 days. The
days are stored in memory if the power is interrupted.
Note: It is not recommended that this feature be turned OFF. In order to
continually maintain clean and working lters, it should be program as
instructed.
3. Tap
Set
to conrm and save your changes.
4. When the timer expires, a message will appear on the control panel
display, page 67. The lters must be cleaned or replaced. Follow
the instructions above to reset the timer. If you tap “snooze” the
message will clear but the error icon will display and the reminder
screen will reappear in 10 days. Refer to Section 13.1, page 51,
for cleaning instructions.
C. Programming the ProClarity Depth Filter Timer
A programmable lter timer can be set to remind you when to replace the
ProClarity Depth Filter.
1. When you enter the “Water Care”
Menu, Figure 12.6d, tap > or > until you
reach the “ProClarity Depth” option,
Figure 12.6e.
2. Slide your nger up and down to roll
the days scroll wheel to adjust the
number of days from OFF to 90. The
adjustments are made in increments
of 10 days. The days are stored in memory if the
power is interrupted.
Note: It is not recommended that this feature be turned OFF. In order to
continually maintain clean and working lters, it should be program as
instructed.
3. Tap
Set
to conrm and save your changes.
4. When the timer expires, a message will appear on the control panel
display, page 67. Follow the previous instructions to reset the
timer. The lter must be replaced. Refer to Section 13.1, page 51,
for lter location. If you tap “snooze” the message will clear but the
error icon will display and the reminder screen will reappear in 10
days.
Water Care
set to
180
0 days
Set
>
ProClarity
>
Figure 12.6d
Water Care
set to
90
0 days
ProClarity Depth
>
Set
>
Figure 12.6e
Page 52
Page 46
D. Programming the Water Change Timer
A programmable “Water Refresh” reminder can be set to remind you
when to drain and rell the spa.
1. While in the “Water Care” Menu, Figure
12.6e, tap > or > until you reach the
“Water Change” option, Figure 12.6f.
2. Slide your nger up and down to roll
the days scroll wheel to adjust the
number of days from OFF to 180. The
adjustments are made in increments
of 30 days. The days are stored in memory if the
power is interrupted.
Note: It is not recommended that this feature be turned OFF. In order to
continually maintain the water healthy and clean, in addition to chemical
maintenance, it should be program as instructed.
3. Tap
Set
to conrm and save your changes.
4. When the timer expires, a message will appear on the control panel
display, page 67. The water must be drained and replaced with
fresh water. Follow the instructions above to reset the timer. If you
tap “snooze” the message will clear but the error icon will display
and the reminder screen will reappear in 10 days. Refer to Section
13.1, page 51, for lter location.
12.7 Locking the Spa
From the “Settings” menu, tap > next to “Lock” to enter the programming
options, Figures 12.7a and 12.7b. You can prevent users from changing
certain features of the spa. When a lock feature is active, the lock icon
will appear of the status bar. When you enter the “Lock” menu, if one of
the three settings is active, it will be highlighted orange.
Water Care
set to
180
0 days
Water refresh
>
Set
>
Figure 12.6f
Time & Date
Language
Lock
SETTINGS
>
>
>
LOCK
0000
set lock level
lockunlock
temp spa service
Figure 12.7a
Figure 12.7b
Page 53
Page 47
A. Temp Lock:
1. Tap
Temp
to lock the temperature
feature, Figure 12.7c.
2. Use the scroll wheel
0000
to assign a
4-digit lock and unlock code by sliding
your nger to change the numbers.
3. Tap
lock
to activate the locking feature.
4. The adjust temperature feature is
disabled, but the spa will still perform all scheduled
tasks.
5. Tap to return to the Settings Menu.
B. Spa Lock:
1. Tap
Spa
to lock the spa, Figure 12.7c.
2. Use the scroll wheel
0000
to assign a 4-digit lock and unlock code by
sliding your nger to change the numbers.
3. Tap
lock
to activate the locking feature.
4. All activation and adjustment features are disabled but the spa will
still perform all scheduled tasks.
5. Tap to return to the Settings Menu.
C. Service Lock:
1. Tap
Service
to lock the spa, Figure 12.7c.
2. Use the scroll wheel
0000
to assign a 4-digit lock and unlock code by
sliding your nger to change the numbers.
3. Tap
lock
to activate the locking feature.
4. All spa functions are locked to allow for a temporary service mode for
lter cleaning.
5. Tap to return to the Settings Menu.
6. When you exit this lock mode, a blow out cycle will start, page 43.
Note: This mode has a time out of 2 hours. The spa should not be left
in this lock mode for an extended period. Especially in colder climate or
when freezing conditions exist.
D. To Unlock (Figure 12.7c):
1. Enter the Lock menu. The type of lock that is active will already be
highlighted.
2. Tap
0000
(the rst block) to start entering the code. Then move on
to the next number until the four-digit unlock code has been entered.
3. Tap
unlock
to unlock.
4. Tap to exit the menu.
Note: A default passcode can be used in case the original passcode is
lost or forgotten. The code “0772” will unlock the locked setting.
LOCK
0000
set lock level
lockunlock
temp spa ser vice
Figure 12.7c
Page 54
Page 48
12.8 Programming the Time and Date
From the “Settings” menu, tap > next to “Time & Date” to enter the
programming options, Figures 12.8a and 12.8b.
A. To set the time and date:
1. Tap
Time
to program the time, Figure
12.8c.
2. Slide your nger up and down to roll the
time scroll wheels to adjust the time.
The “am” and “pm” will adjust according
as the time is changed.
3. Tap
Date
to program the date, Figure
12.8d.
4. Slide your nger up and down to roll the
date scroll wheels to adjust the date.
Each setting for month, day and year
can be set independently.
5. The default time setting is a 12-hour
conguration. To choose the 24-hour
conguration, then tap 24, Figure 12.8d,
to change the setting.
6. Tap
Set
to save and accept the changes.
12.9 Programming the Language
From the “Settings” menu, tap > next to “Language” to enter the
language options, Figures 12.9a and 12.9b.
Indicates that the feature is active. Indicates that the feature is not
active.
Time & Date
Language
Lock
SETTINGS
>
>
>
Time & Date
Time
Set
8 00
Date
pm
24
6:45p 01/01/2015
Figure 12.8a
Figure 12.8b
Time & Date
Time
Set
8 00
Date
pm
24
6:45p 01/01/2015
Figure 12.8c
Time & Date
6:45p
Time
Set
1 26 2015
Date
24
01/01/2015
Figure 12.8d
LANGUAGE
English
French
Deutsch
Time & Date
Language
Lock
SETTINGS
>
>
>
Figure 12.9a
Figure 12.9b
Page 55
Page 49
1. There are 4 languages to select from: English, French, Deutsch, and
Spanish. To view the selections, use the scroll wheel to move up and
down. To select a language, tap next to the language you want to
display, Figure 12.9c.
12.10 Wi-Fi Setup
Connecting to your home Wi-Fi network. From the “Settings” menu,
tap > next to “Wi-Fi” to enter the programming options, Figures 12.10a
and 12.10b. Make sure you have downloaded the Wi-Fi App for this
setup.
1. You need to follow the instructions from
the App in order to connect the Wi-Fi.
2. While the system attempts to connect
you will see the, “Spa Wi-Fi Setup
in-progress,” Figure 12.10b. When the
connection is done the display will read,
“Spa Wi-Fi Setup Connection Success,”
Figure 12.10c.
If the Wi-Fi connection setting should need to be updated or connected
to a new router, follow the steps below.
1. From the “Settings” menu, tap
>
next to “Wi-Fi” to enter the menu.
2. Tap
Reset?
. The display will change to “Spa Wi-Fi Setup
In-progress” and the reset button will be highlighted in orange.
3. Tap
Reset?
again. This will clear the current data and allow the spa
to connect to the new data.
4. Recongure and setup your spa by following the instructions from
the app.
Figure 12.9c
LANGUAGE
English
French
Deutsch
LANGUAGE
Spanish
Water Care
WiFi
Heat & Filter
SETTINGS
>
>
>
WiFi Connect
Spa Wi-Fi Setup
In-progress
reset?
Figure 12.10a
Figure 12.10b
WiFi Connect
Spa Wi-Fi Setup
Successfully Connected
reset?
Figure 12.10c
Page 56
Page 50
System and Wi-Fi Router Requirements
a. The hardware for the Jacuzzi ProLink™ communicates over a 2.4
GHz home network supporting 802.11b/g wireless technology. The
hardware does not support 5 GHz networks.
• If you have 2 Wi-Fi networks, one at 2.4 GHz and the other at 5 GHz,
then make sure that your smart phone is connected to the 2.4 GHz
network throughout the setup process. It is recommended that you
turn off your 5 GHz network during the setup process.
NOTE: The system does not support 802.11/ac/n. If your Wi-Fi router
is either 802.11ac or n, it may work with the module if it supports
802.11b/g.
b. Standard wireless setup supports only home network routers
congured to use open (no security) or WEP/WPA/WPA2.
c. Wi-Fi signal strength of -60 dBM or better is highly suggested to
ensure non-interrupted cloud service.
d. The wireless access is not supported on the following systems:
• Guest networks/Hotspots that use a portal page to login.
• Enterprise access points congured to require certicates or some
other form of enterprise authentication (aka “802.1X”, “RADIUS”, or
“WPA/WPA2 Enterprise”).
e. List of compatible routers and access points is published on
Jacuzzi’s website www.jacuzzi.com/hot-tubs/owners-corner/
remote-control/
f. The Wi-Fi module does not prefer any channels (1-11) on the 2.4
GHz band. A Wi-Fi spectrum analyzer can be used to check how
many Wi-Fi networks are operating on different channels on the
2.4 GHz band. If there are too many networks on channel 6 (for
instance), then it is recommended that the customer change the
operating channel of their Wi-Fi network. Most routers auto-change
the channel but there are some routers that may have to be changed
manually.
g. If there are too many devices operating on a customer’s home Wi-Fi
network that may affect the connectivity of the Wi-Fi module (check
the maximum number of devices that can be connected to the
Access Point that the customer is using).
12.11 System Information
This menu will display the current
information for the spa. From the Settings
Menu, tap
Information
to enter the
selection menu, Figure 12.11a. There are
no selections that can be made. The menu
simply provides information.
Informations
-------
Normal
<150 F
81
82
Water Temp
HiLimit Temp
System State
Ambient Temp
DIP Switches
Figure 12.11a
Page 57
Page 51
13.0 Spa Maintenance
Proper and regular maintenance of your spa will help it retain its beauty
and performance. Your authorized Jacuzzi dealer can supply you with
all the information, supplies, and accessory products you will need to
accomplish this.
DANGER: RISK OF SEVERE INJURY OR DROWNING BY
ENTRAPMENT!
• Keep hair, loose articles of clothing or hanging jewelry away
from suction ttings, rotating jets or other moving components to
avoid entrapment that could lead to drowning or severe injury.
• Never use the spa unless all suction guards, lter, lter lid, or
skimmer assembly are installed to prevent body and/or hair
entrapment.
• Never operate or use the spa if the lter, lter lid, or skimmer
assembly are broken or any part of the skimmer assembly is
missing. Please contact your dealer or nearest service center
for service.
• The suction ttings and suction covers in this spa are sized
to match the specic water ow created by the pump(s). If it
is necessary to replace the suction ttings, suction covers or
pump(s), be sure that the ow rates are compatible and are in
compliance with the VGB Safety Act, page 2.
• Never replace a suction tting or suction cover with one rated
less than the ow rate marked on the original suction tting.
Using improper suction ttings or suction covers can create a
body or hair suction entrapment hazard that may lead to drown-
ing or severe injury.
• Owners must alert all spa users to the potential risk of Hair,
Limb, Body, Evisceration (disembowelment), and Mechanical
Entrapment, page 6.
!
13.1 Cleaning the Filter Cartridges
A reminder message appears on the control
panel display after a specied number days
to remind you to clean the skimmer lter and
to check the polishing bag lter. This
reminder must be reset at each lter
cleaning interval. Refer to Section 12.6
(page 45) for additional information and programming details. Your
new spa is equipped with an advanced 2-Stage ltration system. Fine
debris are ltered by the circulation pump drawing water through the
ProClarity™/ProClear™ skimmer and pleated lter cartridges 8 hours
(unless programmed otherwise). Large debris are ltered when jets
pump 1 is running when the spa is in use or during a programmed lter
cycle. These pumps draw water from footwell suction tting and through
a secondary water polishing bag lter and additional lter.
It’s time to clean or replace your ProClarity
and ProClear filters. Contact your autho-
rized dealer if new filters are needed.
Reminder
reset
snooze
Page 58
Page 52
A. Cleaning the lters and lter bag
To ensure optimum performance
1. The ProClarity™ lter cartridge (A) must be
cleaned every month and replaced every 18
months.
2. The ProClarity Depth lter (B) must be replaced
every 3 months.
3. The ProClarity lter canister (C) can be rinsed
when the lters are cleaned.
4. The ProClear II skimming lter cartridge (D) must be
cleaned every month and replaced every 18 months.
5. The ProClarity debris bag (E) should be checked and
emptied monthly.
To accomplish this, refer to the following lter cleaning
procedure. The circulation pump lter goes on the side that
has the wall tting with the grids, Figure 13.1a.
Note: Do not attempt to wash the ProClarity depth lter (B)
and the ProClear/ProClarity debris bag (E) or it will come
apart!
B. Cleaning the Filters/Debris bag:
A
DANGER: TURN POWER TO SPA OFF! TO DECREASE
RISK OF DEATH, DROWNING, OR ENTRAPMENT, NEVER
OPERATE SPA WHEN FILTER IS NOT PROPERLY INSTALLED
OR IF SKIMMER ASSEMBLY IS DAMAGED OR ALTERED!
B
(Spa
Shell)
Lift the cover upward to
access lter cartridges.
C
Remove the ProClarity
debris bag from clips
and then clean out
debris.
D
(Spa Shell)
Rotate each lter
cartridge handle
counterclockwise to
unthread from mating
wall tting.
A
B
C
D
E
Figure 13.1b
Debris
Bag
Page 59
Page 53
E
Lift unthreaded lter
cartridge from skimmer
well.
F
Cartridge 1
If used, remove the
chemical feeder as
instructed prior to rinsing
the lter cartridge. Rinse
debris from lter pleats
using a garden hose and
high-pressure nozzle.
Start at the top and
work downward towards
handle. Repeat until all
pleats are clean.
G
1 1
Remove the lter pins
1
in order to separate
the ProClarity lter and
canister.
H
1
2
3
Once the lter pins are
removed, rotate the
lter cartridge handle
counterclockwise to
unthread from the lter
canister. You can clean
the lter
1
and canister
3
, but you must
replace the ProClarity
Depth Filter
2
every 3
months.
I
Canister
Cartridge 2
Rinse debris from lter
pleats using a garden
hose and high-pressure
nozzle. Start at the top
and work downward
towards handle. Repeat
until all pleats are clean.
Rinse out any debris
from the canister.
J
1 1
Reassemble the
ProClarity Filter.
Remember to replace
the depth lter with a
new one. Once the lter
is assembled, secure it
with the lter pins
1
.
Page 60
Page 54
K
Trapped
Air
Bubbles
Cartridge 1
Cartridge 2
Submerge both lter
cartridges in spa. Tilt
threaded end upward
to remove trapped air
bubbles, then keep
cartridges submerged to
prevent air entrapment
during installation.
L
Place each cartridge
back into skimmer
well, then rotated
each cartridge handle
clockwise to thread back
into wall tting. DO NOT
OVERTIGHTEN!
M
Install clean debris bag
back onto the lter cover
clips as shown (you can
ip the lter skimmer
and use the back side to
extend usage).
N
(Spa
Shell)
Reinstall the skimmer
shield over the lters.
Then turn power to spa
back on.
Debris
Bag
Page 61
Page 55
13.2 Draining and Refilling
About every 3 months, you will want to replace the spa’s water. The
frequency depends on a number of variables including the amount of
use, number of users, attention paid to water quality maintenance, etc.
During this time, it is also recommended that you use Jacuzzi’s Jet Line
Cleaner to clean the internal plumbing lines from buildup and debris.
Note: Jacuzzi chemicals are for use in the U.S. only.
CAUTION! READ THIS BEFORE DRAINING: To prevent damage to the spas components, turn off power to the spa at the circuit
breaker before draining it. Do not turn the power back on until your
spa has been relled.
CAUTION: There are certain precautions to keep in mind when
draining your spa. If it is extremely cold, and the spa is outdoors, freezing could occur in the lines or the equipment (see
“WINTERIZING,” page 58). On the other hand, if it is hot outdoors, do not leave the spa’s surface exposed to direct sunlight.
A. To drain your spa, perform the following steps (standard drain):
1. Turn off power to spa at breaker.
2. Locate the drain valve located on the front
left corner on the black plastic pan. Hold the
larger (rear) drain valve body to prevent it
from turning, then loosen and remove the
front cap to expose the underlying male hose
threads, Figure 13.2a.
3. Attach a garden hose to the exposed threads,
Figure 13.2b.
4. Gently rotate the larger (rear) valve body 1/3 turn
counterclockwise to unlock the drain valve, Figure
13.2c.
5. Pull the larger (rear) body outward as shown
to open drain, Figure 13.2d.
6. After the spa drains, perform steps 2-5 in reverse
order to close the drain prior to relling spa.
After relling, turn on power to the spa and follow the
steps listed under “Spa Fill Up Procedures” (page 17).
Always ll your spa through both lter buckets.
Figure 13.2d
Figure 13.2c
Figure 13.2b
Figure 13.2a
Unlock
Drain
Page 62
Page 56
B. To drain your spa, perform the following steps (QuickDrain):
1. Turn off power to hot tub at the breaker.
2. You must rst remove the corner panels in
order to remove the center panel, Figure
13.2e.
3. Grab one of the corner panels, from the
bottom, where it touches the bottom pan.
Then gently pull the panel forward to
unsnap it from the holding clip. Place the
corner panel in a safe location to prevent
from damaging it. Repeat the steps to
remove the other corner panel.
4. Now you need to remove the center panel.
Grab the sides of the panel and gently
pull the cabinet forward until all the clips
have been release then pull up to remove,
Figure 13.2f. Place the panel in a safe
location to prevent from damaging it.
5. Locate the QuickDrain valve, Figure 13.2g.
6. Unscrew drain valve cap, Figure 13.2h.
Place the cap aside.
7. Screw in the adapter with hose that was included in
the equipment bay; attach it to the QuickDrain, Figure
13.2i. Make sure to direct the hose to an area where
the water will drain properly.
8. Open the drain slice valve by sliding the handle to the
side and pulling up.
9. After the hot tub has drained close the slice valve
by pushing it downward and sliding the handle to the
side. Remove the adapter and reinstall the QuickDrain cap
before relling hot tub.
After relling, turn on power to the spa and follow the steps
listed under “Spa Fill Up Procedures” (page 17). Always ll
your spa through both lter buckets.
13.3 Cleaning the Spa Interior
To preserve the sheen of your spa’s surface, it is crucial that you avoid
using abrasive cleaners or cleaners which have adverse chemical effect
on the surface. If you are not certain as to the suitability of a particular
cleanser, consult your authorized Jacuzzi dealer. We recommend using
Jacuzzi’s Spa All Purpose Cleaner to clean the spa’s interior surface.
Use extreme care to assure that no soap residue is left on the surface.
This could cause severe sudsing when the spa is relled. Jacuzzi
chemicals are for use in the U.S. only.
Figure 13.2e
Figure 13.2f
Figure 13.2g
Figure 13.2i
PoweronLamp
on
DANGER!
TURN POWER
OFF! DO NOT
LOOK AT LIT BULB.
SEVERE EYE
DAMAGE OR BLINDNESS
CAN OCCUR!
Figure 13.2h
Page 63
Page 57
13.4 Pillow Care
Clean the headrests in your spa as needed by wiping them with a
cloth with soapy water. It is not necessary to remove the headrests for
cleaning. To remove headrests for long-term storage or replacement,
grasp both ends of each headrest and gently pull inward towards the
center of the spa. To reinstall, over mounting strip and press down until
headrest mounting bracket emits a “click” sound.
13.5 Maintaining the Synthetic Cabinet
The synthetic cabinet requires little or no maintenance of any kind. To
clean, simply wipe cabinet with mild detergent soap solution and a clean
towel.
13.6 Cleaning the Control Panel
To clean, simply wipe control panel with a micro-ber cloth that is used
for cleaning polycarbonate lenses.
13.7 Cover Care and Maintenance
Certain hot tub covers distributed by Jacuzzi Hot Tubs have a vinyl
or PROLAST™/PROLAST™ Extreme encasement. This vinyl or
PROLAST™/PROLAST™ Extreme encasement also referred to as the
cover “skin” is attractive and durable. Regular monthly cleaning and
conditioning (vinyl) is strongly recommended and may increase the
longevity of your cover. Jacuzzi chemicals are for use in the U.S. only.
A. To Clean and Condition the Cover
1. Use a garden hose to loosen debris and dirt.
2. Using a large sponge or a soft bristle brush, use diluted or mild soap
and scrub the vinyl top.
3. Rinse clean and do not allow soap to dry on cover. Do not use soap
on the underside of the cover.
4. Please check with your Jacuzzi Dealer about purchasing Jacuzzi’s
cover care and conditioning products. Condition using non-petroleum
based conditioners to keep the vinyl supple and threads/stitching
from drying out.
5. Do not use solvents, abrasive cleaners or strong detergents. Do not
use products that contain silicone or alcohol.
B. Additional Care and Maintenance Instructions:
1. Debris can accumulate on the spa cover. Removal of snow or other
debris will help to avoid breakage of the foam cores.
2. Be sure to lock the cover straps to secure the cover from unwanted
or accidental entry.
3. Do not place heavy objects on the vinyl.
4. Do not walk, sit or stand on the cover.
CAUTION: Never spray cabinet with a high pressure garden
hose for any reason since this action may induce an electrical
short in the spa’s electrical equipment.
Page 64
Page 58
5. Do not drag or use the aps/skirt or the cover lock straps to remove
the cover.
6. Use only recommended cover lift systems.
7. Use only chemicals and cleaners recommended by Jacuzzi.
8. Remember to keep spa covered when not in use. Maintaining proper
water levels assures efcient operation and efcient electrical usage.
9. Do not expose your spa to the sun for extended periods of time as
UV rays can damage the interior surface.
10. Use caution when removing cover. Before removing cover, assure all
locks have been released to avoid lock breakage and or cover strap
damage.
13.8 Winterizing
Your Jacuzzi spa is designed to automatically protect itself against
freezing when operating properly. During periods of severe freezing
temperatures, you should check periodically to be certain that the
electrical supply to the spa has not been interrupted. In extreme, bitter
cold weather (less than 0°C) we recommend that the circulation pump is
set for 24-Hour operation (Section 12.2 Programming The Primary Filter
Cycle, page 41) and that auto-heating is selected (Section 12.1 AutoHeating, page 41) to protect against damage to the spa.
If you do not intend to use your spa, or if there is a prolonged power
outage during periods of severe freezing temperatures, it is important
that all water be removed from the spa and equipment to protect
against damage from freezing.
Expert winterization of your spa is highly recommended; contact
your authorized Jacuzzi dealer. In emergency situations, taking the
following steps can minimize damage:
CAUTION: TURN OFF POWER TO SPA.
1. Follow the directions on page 55 for draining the spa.
2. Turn the massage/diverter selector(s) into the middle combo position
to allow the water in the plumbing lines to drain, page 39.
3. Turn the waterfall valve to the open position to allow the water in the
plumbing lines to drain, page 38.
4. As the water level drops below the seats, use whatever means
necessary to get the water out of the recessed seating areas and
into the footwell, such as a wet/dry vacuum.
5. Open all the air controls and leave them open until you resume use
of the spa, page 38.
6. When the water level ceases to drop, use whatever means available
to remove any remaining water from the footwell, such as a wet/dry
vacuum.
7. Remove the equipment-side cabinet panels and locate the drain
plugs in the front of each pump (Figure 6.0a, page 14). Remove
these plugs to allow the water to drain out of the pumps and heater.
Page 65
Page 59
Note: Approximately one to two gallons will be released during this
procedure. Use a wet/dry vacuum or other means to keep this from
ooding the equipment compartment. Replace the drain plugs.
8. Loosen hose clamp at bottom of heater (Figure 6.0a, page 14)
and pull hose off of heater tting (twist the hose back and forth while
pulling downward). Tip hose down and allow it to drain and then
reinstall hose and clamp.
9. Loosen the hose clamp on the circulation pump (if equipped) intake
behind the control box (Figure 6.0a, page 14) and pull the hose off
(twist hose back and forth while pulling outward). Tip hose down and
allow it to drain and then reinstall hose and clamp.
10. Loosen hose clamp at bottom of CLEARRAY ® system and pull hose
off of CLEARRAY tting (twist the hose back and forth while pulling
downward). Tip hose down and allow to drain. Then reinstall hose
and clamp. Remove the cover of the CLEARRAY system to access
the UV bulb and quartz tube. Remove and store the UV bulb in a
safe location. Remove and dry off the quartz tube then reinstall it.
Depending on the length of time, consider replacing the UV bulb
when you resume use of your hot tub.
11. Re-install cabinet side panels and cover spa so that no casual
moisture can enter into it.
Consult your Jacuzzi dealer if you have any questions regarding winter
use or winterizing.
13.9 Restarting Your Spa in Cold Weather
If you want to start up your spa after it has sat empty for a time in
freezing temperatures, be aware that the water remaining in certain
Sections of the piping may still be frozen. This situation will block water
ow preventing the spa from operating properly and possibly damaging
the equipment. We recommend you consult your dealer for guidance
before attempting to restart your spa under these conditions.
14.0 Water Quality Maintenance
To decrease the risk of contracting a waterborne illness (e.g. an infection,
bacteria or virus) and/or respiratory ailments
, m
aintain water quality
within specied limits. This will enhance your enjoyment and prolong
the life of the hot tub’s equipment. Doing so requires regular attention
because the water chemistry involved is a balance of several factors.
Procrastination in regard to water maintenance will result in poor and
potentially unhealthful conditions for soaking and even damage to
your hot tub investment. For specic guidance, on maintaining water
quality, consult your authorized Jacuzzi dealer who can recommend the
appropriate Jacuzzi chemical products. Jacuzzi chemicals are for use in
the U.S. only.
Page 66
Page 60
WARNING: FAILURE TO MAINTAIN WATER QUALITY
WILL:
• Increase risk of contracting a waterborne illness (e.g. an
infection bacteria or virus) and/or respiratory ailments
.
• Damage the equipment, components and spa shell, which
are not covered under the hot tub’s warranty.
!
CAUTION: Never store hot tub chemicals inside the hot tub’s
equipment bay. The equipment bay may reach elevated temperatures, this is where high voltage electronic devices are located. This
area is not intended for storage of any kind.
14.1 pH Control
pH is a measure of relative acidity or alkalinity of water and is measured
on a scale of 0 to 14. The midpoint of 7 is said to be neutral, above which
is alkaline and below which is acidic. In spa water, it is very important
to maintain a slightly alkaline condition of 7.4 to 7.6. Problems become
proportionately severe the further outside of this range the water gets.
A low pH will be corrosive to metals in the spa equipment. A high pH will
cause minerals to deposit on the interior surface (scaling). In addition,
the ability of the sanitation agents to keep the spa clean is severely
affected as the pH moves beyond the ideal range. That is why almost all
spa water test kits contain a measure for pH as well as sanitizer. Jacuzzi
offers products that help you maintain the ideal range. These chemicals
are for use in the U.S. only.
14.2 Sanitizing
To destroy bacteria and organic compounds in the spa water, a sanitizer
must be used regularly. Chlorine and bromine are the two most popular
sanitizers used to date. The “Proclear Mineral Spa Clarier” designed
especially for your hot tub is a benecial product for water maintenance.
Many other additives are available for your spa. Some are necessary
to compensate for out-of-balance water; some aid in cosmetic water
treatment and others simply alter the feel or smell of the water. Your
authorized Jacuzzi dealer can advise you on the use of these additives.
When adding spa shock (chlorine or non-chlorine) or pH balancing
chemicals activate the jet pump(s) and leave the spa cover open for a
minimum of 20 minutes. By doing this you will allow excessive chemical
vapors to exit the spa, protecting pillows and plastic knobs from chemical
attack.
Page 67
Page 61
WARNING: RISK OF PERSONAL INJURY, DROWNING
OR ENTRAPMENT!
Never leave your hot tub unattended for any reason while the
cover is open and accessible, especially to small children and
animals!
CAUTION: RISK OF PERSONAL INJURY OR SPA DAMAGE!
Never add chlorine tablets (trichlor) or acid to your hot tub for
any reason! These chemicals may damage components within
your hot tub, burn or irritate your skin, create a rash and void
the manufacturer warranty for your spa.
!
14.3 Other Additives
Many other additives are available for your spa. Some are necessary
to compensate for out-of-balance water, some aid in cosmetic water
treatment and others simply alter the feel or smell of the water. With our
chemical products your authorized Jacuzzi dealer can advise you on the
use of these additives. Jacuzzi chemicals are for use in the U.S. only.
14.4 CLEARRAY® (Ultraviolet) Water Purification System
CLEARRAY Water Purication System is exclusive
technology utilizing natural ultraviolet technology to
eliminate waterborne bacteria, viruses, and algae in
portable spas. The ultraviolet light otherwise known as
UV-C or germicidal light inactivates the microorganisms
disrupting the DNA so that it cannot reproduce and is
considered lifeless. CLEARRAY is plumbed in-line with
your ltration system. After the water is drawn from the
pump, lter, and heater it is then directed though the CLEARRAY system.
Water passes through an ultraviolet light energy that treats and disinfects
the water. The water is then pumped back into the spa giving you crystal
clear water instantly. The system has a ballast that is the power supply
for the purication system (Figure 14.4a); it has two LED indicator lights.
The “Power On” (red color) indicating incoming power ow and the
“Lamp on” (green color) indicating the system is properly working.
CLEARRAY is standard for all models.
After a year the bulb must be replaced. If the CLEARRAY timer has
been programmed correctly a message will appear on the LCD display
when the time allotted has expired. In order to clear the message, a new
CLEARRAY UV bulb needs to be installed and the timer must be reset,
page 44.
PoweronLamp
on
Figure 14.4a
Page 68
Page 62
WARNINGS:
• Do not operate the UV-C emitter when it is removed from the appli-
ance enclosure.
• This appliance contains a UV-C emitter.
• Unintended use of the appliance or damage to the housing may
result in the escape of dangerous UV-C radiation. UV-C radiation
may, even in little doses, cause harm to the eyes and skin.
• Appliances that are obviously damaged must not be operated.
• Read the maintenance instructions before opening the appliance.
!
14.5 CLEARRAY® Bulb Replacement and Quartz Tube Maintenance
Important: It is MANDATORY that the CLEARRAY UV bulb is replaced
and the quartz tube be cleaned every 12 months to maintain optimum
performance.
!
DANGER: TURN THE SPA BREAKER TO THE OFF
POSITION!
!
WARNING: DRAIN THE SPA IF YOU ARE REPLACING OR
CLEANING THE QUARTZ TUBE!
!
WARNING: ALLOW BULB TO COOL DOWN PRIOR TO
REMOVING FROM QUARTZ TUBE.
!
DANGER: NEVER LOOK AT THE LIT BULB. THIS CAN
CAUSE SEVERE EYE DAMAGE OR BLINDNESS.
UV bulb replacement and quartz tube maintenance:
Note: Location of CLEARRAY System and connection may vary by
model.
1. Turn the breaker to the spa OFF. DRAIN YOUR SPA.
Note: If you are only replacing the UV bulb then the spa does not have
to be drained. You will need to drain it if you are replacing or cleaning the
quartz tube.
1
2
3
4
7
5
8
9
11
12
10
6
#3 shown as reference only.
It is attached to the #10 metal plate.
Figure 14.5a
Page 69
Page 63
2. Once the UV bulb has cooled off remove the
CLEARRAY System enclosure cover (2) by removing
the four screws (1). This will expose the UV bulb and
connections, Figure 14.5b.
DANGER: NEVER REMOVE COVER WITHOUT FIRST
TURNING OFF AT POWER SOURCE AND DRAINING THE
SPA.
!
3. Disconnect UV bulb socket (6) from the power cord socket (4),
Figure 14.5c.
4. Slowly remove the UV bulb (7) out of the quartz tube, Figure 14.5d.
5. Remove the quartz seal compression nut (9) by turning it
counterclockwise, Figure 14.5e. Use a pair of channel-lock pliers if
needed, Figure 14.5f.
6. Now you are ready to clean or replace the quartz tube (8). For
cleaning the quartz tube, follow steps 7 and 8 then proceed from step 9.
For replacing quartz tube, skip steps 7 and 8 and proceed from step 9.
7. Cleaning quartz tube: Clean the quartz tube by wiping, until clear,
using a paper towel or a dry cotton cloth. If needed, a household tub
and shower lime removal product can be used.
WARNING: Do not use abrasive cleaners as they can
scratch the quartz tube surface.
!
8. Rinse the quartz tube with clean water to completely remove any
cleaning products that were used in step 7.
9. Replacing quartz tube: Remove the black o-ring from the quartz
tube and place it on the new tube. Place the new quartz tube (8) into
the water chamber (12) with the domed end rst making sure it is
inserted and seated inside the quartz end holder (11).
10. Reinstall and hand tighten the quartz seal compression nut (9) by
turning it clockwise.
11. Rell your spa.
12. System Test 1: Assure there is no water dripping from the seal
compression nut (9). If water is visible, STOP and tighten the
compression nut (9) using a pair of channel lock pliers to a maximum
of 1/4 turn. If that does not x the leak, then repeat quartz tube
maintenance process from step 1 through step 11. Make sure there
is no water leaking before proceeding to step 13.
Figure 14.5b
Figure 14.5c
Figure 14.5d Figure 14.5e Figure 14.5f
4
6
P
o
w
er
L
a
m
p
O
n
O
n
7
P
o
w
er
L
a
m
p
O
n
O
n
9
Page 70
Page 64
13. System Test 2: Reconnect the CLEARRAY unit to the controller.
Turn breaker back ON. Turn on the pump to circulate the water
through the CLEARRAY System. Wait for 5 minutes and assure no
water is dripping. If water is visible, STOP, x the leak by repeating
quartz tube maintenance process from step 1 through step 12. Make
sure there is no water visible. Turn the pump and breaker OFF
BEFORE proceeding to step 14.
14. Reconnect the UV bulb socket (6) to the power cord socket (4) make
sure you use the latex glove provided when handling the UV bulb.
WARNING: DO NOT TOUCH THE NEW UV BULB WITH
YOUR BARE HAND. Oil on your skin will cause hot spot on
the UV bulb and shorten the life of your UV bulb. Use the provided latex glove to handle the UV bulb.
!
15. Slide the new UV bulb (7) back inside the quartz tube.
16. Reinstall the black bulb boot (5) back over the quartz seal
compression nut (9).
17. Reinstall the enclosure cover (2) and secure with the screws.
18. Properly dispose of the old UV bulb.
WARNING: This CLEARRAY System includes a UV bulb,
which contains mercury. Dispose of the bulb in accordance
with disposal laws. See www.lamprecycle.org.
!
19. Once power is activated you can check the ballast,
Figure 14.5g, to see if the CLEARRAY System is
functioning. The power on (red) light indicates that
the CLEARRAY System is being provided power
and should always be on. The lamp on (green) light
indicates that UV bulb is activated.
Figure 14.5g
PoweronLamp
on
Page 71
Page 65
15.0 Error/Display Messages
There are a number of unique functions designed into your Jacuzzi spa
to protect it from damage and/or to aid in troubleshooting. When an error
occurs the spa will notify you by showing the screen below and an error
code, Figure 15.0a. Following is a listing of all the possible messages
along with their meanings. Always insist on genuine Jacuzzi
replacement parts.
Note: If you tap the display will change to Figure 15.0b. The error
icon will remain on the screen as a reminder. If the error is not taken
care of or xed, the error display will reappear in 2 hours, Figure 15.0a.
1. Open Flow Switch: (Heater is deactivated. The lter/circulation may
also be deactivated.) The ow switch is malfunctioning open, the
circulation pump’s lter cartridge is excessively dirty or an air lock
condition has occurred at the circulation pump intake. Contact your
authorized dealer or service organization.
2. Closed Flow Switch: (Heater is deactivated. The lter/circulation
may also be deactivated.) The ow switch is malfunctioning closed.
Contact your authorized dealer or service organization.
3. Shorted Hi-limit Temp Sensor: The hi-limit temperature sensor is
not functional. Heater is disabled. This must be repaired only by a
qualied authorized service organization or service technician.
4. Open Hi-limit Temp Sensor: The hi-limit temperature sensor is not
functional. Heater is disabled. This must be repaired only by a
qualied authorized service organization or service technician.
5. Shorted Water Temp Sensor: The temperature sensor is not
functional. Heater is disabled. This must be repaired only by a
qualied authorized service organization or service technician.
6. Open Water Temp Sensor: The temperature sensor is not functional.
Heater is disabled. This must be repaired only by a qualied
authorized service organization or service technician.
7. Shorted Ambient Temp Sensor: The temperature sensor is not
functional. Heater is disabled. This must be repaired only by a
qualied authorized service organization or service technician.
Monitors the controller temperature.
Figure 15.0a
Figure 15.0b
The flow switch is malfunctioning open. Heater
is disabled. The circulation pump’s filter is
excessively dirty, or an air lock has occurred at
the circulation pump intake. Contact your
authorized dealer or service organizations.
FLOW ERROR
96
6:45 PMON
Page 72
Page 66
8. Open Ambient Temp Sensor: The temperature sensor is not
functional. Heater is disabled. This must be repaired only by a
qualied authorized service organization or service technician.
Monitors the controller temperature.
9. Closed Flow Switch on Start-up: Flow switch is non-functional.
Closed or shorted ow switch on system start-up (system disabled).
Contact your authorized dealer or service organization.
10. Frozen on Start-up: Flow switch is non-functional. Shorted ow
switch on system start-up (system disabled) and freeze condition
detected. Contact your authorized dealer or service organization.
11. Cool Warning: Spa water is more than
20°F/11°C cooler than the temperature set
point, the circulation pump and heater will
automatically activate to provide freeze
protection. The spa will stay in this mode until the
water temperature reaches 15°F/8°C below the set
temperature. No corrective action is necessary.
Note: The heater icon
ON
will be blinking and the error icon will be
displayed under the temperature.
12. Freeze protection: A potential freeze condition has been detected. No
action is required. Jets pump(s) operate until the spa is out of danger.
No corrective action is necessary. If condition persists, contact your
authorized dealer or service organization.
13. Overheat protection: DO NOT ENTER THE WATER! Water
temperature is above acceptable limits. Heater is deactivated.
Remove spa cover to speed cooling. If condition persists, contact
your authorized dealer or service organization.
Note:
• As a safety measure, the red lights of the spa will ash on and off as
an indication that the spa is an overheat condition.
• The heater icon
ON
will be blinking and the error icon will be dis-
played under the temperature.
14. Watchdog Protection: DO NOT ENTER SPA! Water temperature is
above acceptable limits. Your spa is deactivated. Remove spa cover
to speed cooling. If condition persists, contact your authorized dealer
or service organization.
Note: The heater icon
ON
will be blinking and the error icon will be
displayed under the temperature.
96
6:45 PMON
Figure 15.0c
WARNING: RISK OF HYPERTHERMIA (OVER-HEATING)
CAUSING SEVERE INJURY, BURNS, OR WELTS.
!
WARNING: RISK OF HYPERTHERMIA (OVER-HEATING)
CAUSING SEVERE INJURY, BURNS, OR WELTS.
!
Page 73
Page 67
15. Watchdog Freeze Protection: Spa water is below 40°F/4.4°C. Jet
pumps operate until the spa is out of danger. Contact your authorized
dealer or service organization.
Note: The heater icon
ON
will be blinking and the error icon will be
displayed under the temperature.
16. Controller Overheat Protection: Controller temperature has exceeded
acceptable limits. If condition persists, provide shade for equipment
side of spa. Contact your authorized dealer or service organization.
Note: The heater icon
ON
will be blinking and the error icon will be
displayed under the temperature.
17. Panel Com Error: The topside controller is having trouble
communicating to your spa. Contact your authorized dealer or
service organization.
18. Stereo Com Error: The stereo is having trouble communicating to
your spa. Contact your authorized dealer or service organization.
19. CLEARRAY Replacement Reminder
This message will appear when the CLEARRAY
bulb reminder time has expired (Figure 15.0d).
The CLEARRAY bulb must be replaced.
20. ProClarity/ProClear Filter Reminder
This message will appear when the lter reminder
time has expired (Figure 15.0e). Remove the
ProClarity/Proclear lters and lter/debris bag for
cleaning or replacement.
21. ProClarity Depth Filter Reminder
This message will appear when the lter reminder
time has expired (Figure 15.0f). The ProClarity
Depth lter must be replaced.
22. Water Refresh Reminder
This message will appear when the “Water
Refresh” timer has expired (Figure 15.0g). The
water needs to be drained and relled with fresh
water.
23. Extended Temperature Activated:
The spa is set to go up to 104°F (40°C), but it can be set to reach
106°F (41°C). To access the extended temperature you need press
and hold your nger over the temperature reading for about 5
seconds. The temperature reading will start to blink to indicate the
system is ready. Tap to raise the temperature up to 106°F (41°C).
Note: The heater icon
ON
will be blinking to indicate that the feature is
active.
It’s time to replace your CLEARRAY bulb.
Contact your authorized dealer for replace-
ment parts.
Reminder
reset
snooze
Figure 15.0d
It’s time to clean or replace your ProClarity
and ProClear filters. Contact your autho-
rized dealer if new filters are needed.
Reminder
reset
snooze
Figure 15.0e
It’s time to replace your ProClarity Depth
Filter. Contact your authorized dealer for a
new filter.
Reminder
reset
snooze
Figure 15.0f
Your spa needs to be drained and refilled
with fresh water. Refer to your owner’s
manual for draining procedure.
Reminder
reset
snooze
Figure 15.0g
Page 74
16.0 Troubleshooting Procedures
In the unlikely event your spa is not working the way you believe it
should, please rst review all the installation and operating instructions in
this manual and check the message on the panel display; second, if you
are still not satised it is working properly, please follow the appropriate
troubleshooting instructions.
PROBLEM PROCEDURE
NONE OF THE
COMPONENTS
OPERATE (i.e.
pump light)
Check the control panel lights.
1. If there are letters or symbols displayed on the
screen, refer to the previous Section 15.0 to
determine the meaning and action required.
2. If nothing appears on the screen:
A. Check the household circuit breaker.
B. Contact you dealer or authorized service
center.
PUMP DOES
NOT OPERATE
Activate the “JETS”:
1. If no sound is detected or if a “buzzing” sound
is detected, turn off power to the spa and
contact your dealer or service center.
2. If motor operates but no water ows to jets:
A. Pump may not be properly primed. See
instructions below.
B. Contact dealer or authorized service center.
Pump Priming Instructions:
1. Turn off power to the spa.
2. Remove the handle from the massage selector supplied by the pump
you are priming.
3. Loosen the massage selector’s cap slightly (counterclockwise),
listening for the air to seep out.
4. Tighten the cap nger-tight, replace the handle and turn the hot tub’s
power back on.
Note: This method must be used for the jet’s pumps because these
pumps are not connected to the main lter system in any way.
CAUTION: If freezing conditions exist and pump is not operational,
take measures to protect the system from freeze damage. See
Section 13.8 titled “Winterizing” (page 58).
Page 68
Page 75
Page 69
POOR JET ACTION 1. Make certain the jets pump is turned on.
2. Check position of massage selectors.
3. Open air control for selected jet system.
4. Check for adequate water level.
5. Check for dirty lter (page 51).
WATER IS TOO HOT 1. Reduce thermostat setting.
2. Switch hot tub to “Economy” mode to turn
heater on only during pre-programmed
time (page 41).
3. Make sure the pumps are turned off and
not constantly running.
NO HEAT 1. Check thermostat setting.
2. Keep the cover in place while heating.
3. If heater indicator is displayed, but no
temperature increase is experienced after
a reasonable period of time, contact your
dealer or authorized service center.
FILTER/CIRCULATION
PUMP OFF
1. Verify lter/circulation pump is
programmed to run 8 hours a day (page
41).
2. Make sure there are no errors preventing
the pump from turning on.
3. Hot tub water is warmer than 95°F (34°C)
and two degrees warmer than the set
temperature. The “Summer Logic” safety
feature has activated. See note on page
42 for details.
Jacuzzi builds the best spas in the industry. Nonetheless, we are always
striving to improve the quality and features of our products. Your input
as a Jacuzzi spa owner is a cherished part of this process. If you have
any comments or suggestions, or if you wish to be informed on any new
products for your spa, please write to us.
CONGRATULATIONS on your good taste and welcome to the happiest
and most relaxed family in the world!
Page 76
Page 70
17.0 Typical Spa Wiring Diagrams
17.1 Wiring diagram for North American 60 Hz Models Only
Red (L2)
Pigtail
Neutral Bus
Ground
Black (L1)
Green
Main
Service
Panel
with
GFCI
2-Pole
GFCI
Breaker
Ground/Bonding Lug**
2-Pole Circuit Breaker with 2-Wire Grounded Load Connection
(3 Wires to Hot Tub, 2-Hot (L1-L2), 1-Ground)
White (N)
Black (L1)
Red (L2)
240 VAC
No Load Neutral Wire
Note: service disconnect not
shown in this diagram.
Red (L2)
Red (L2)
Pigtail
Neutral Bus
Ground
Black (L1)
Black (L1)
Green
GFCI Sub Panel*
Main Panel*
2-Pole
GFCI
Breaker
Ground/Bonding
Lug**
No Load Neutral Wire
Main Panel with Secondary GFCI Shut-Off Box Using a
2-Pole GFCI Breaker with 2-Wire Grounded Connection
(3 Wires to Hot Tub, 2-Hot (L1-L2), 1-Ground)
White (N)
Green (Ground)
*GFCI Sub Panel commonly
used when recommended GFCI
does not install in Main Panel.
Note: service disconnect not
shown in this diagram.
B
A
240 VAC
Page 77
Page 71
18.0 Circuit Board Wiring Diagrams
18.1 Domestic 60Hz Wiring Diagram
F1 10A 250VAC
F7 30A
F6 30A
K12
K1
K9
K15
K14
T1
3
2
TB1
4
3
2
1
K5
J22
MAIN PANEL CONNECTIONS
N/A
AV
UV
PUMP 2
N/A
FAN
J43
FUSE PUMP2/AV/UV
FUSE PUMP3
RED
BLK
240V
SINGLE SERVICE
5.5 kW HEATER
J2
K13
J65
J51 J3
J52
J4
J61J62
J49
K11
K10
J59
J44
J48
J39
F5 2A 250VAC
F4 30A
FUSE PUMP1
J28
J30
PUMP 1
OZONE
CIRC PUMP
J27
J34
J29
J50
J56
J57
J63
J37
K8K4K6
K7
F2 1/4AT 250VAC
WATER
TEMP
SERIAL ADCM
PHOTO
FLOW
WATER LEVEL
SENSORS
HI-LIMIT
TEMP
AUX SENSORS
J16
J17
J18
ON
J1
J6
J9
J20
J21
J19 J67
J12
K3
J11
J13 J14
J15
J10
J24
ZONE 2
J25
ZONE 3
J23
ZONE 1
1
2
3
4
5
6
7
8
9
10
J26
ZONE 4
C58
C57
K2
GFCI
TRIP
J8
Q32
HEATER
J60
J66
J55
J54
J38
J53
J45
J46
J47
J41
J58
J42
J31
J32
J33
J40
J64
J36
J35
1
2
3
4
S1
FUSE CIRC/OZONE
STATUS
INDICATOR
GRN
J7 J69 J68
WI-FI
CONTROL PANEL
FLOW SENSOR
WATER
SENSOR
FOOTWELL
LIGHT
BLUEWAVE
STEREO
(OPTIONAL)
CLEARRAY
STEREO POWER
SUPPLY (OPTIONAL)
PUMP 2
LIGHTING
EXPANSION
PUMP 1
CIRC PUMP
HI-LIMIT
SENSOR
240 VAC 32A/40A/48A
3-WIRE CONNECTION
60 Hz 1-PHASE SERVICE
see section 18.3
for dip switch
settings
Page 78
Page 72
18.2 Export 50Hz Wiring Diagram
Dual service shown.
F1 10A 250VAC
F7 30A
F6 30A
K12
K1
K9
K15
K14
T1
3
2
TB1
4
3
2
1
K5
J22
MAIN PANEL CONNECTIONS
N/A
AV
UV
PUMP 2
N/A
FAN
J43
FUSE PUMP2/AV/UV
FUSE PUMP3
LINE 1 BLU
LINE 2 BRN
LINE 1 BLU
LINE 2 BRN
DUAL SERVICE
2.7KW HEATER
J2
K13
J65
J51 J3
J52
J4
J61J62
J49
K11
K10
J59
J44
J48
J39
F5 2A 250VAC
F4 30A
FUSE PUMP1
J28
J30
PUMP 1
OZONE
CIRC PUMP
J27
J34
J29
J50
J56
J57
J63
J37
K8K4K6
K7
F2 1/4AT 250VAC
WATER
TEMP
FLOW
WATER LEVEL
SENSORS
HI-LIMIT
TEMP
AUX SENSORS
J16
J17
J18
ON
J1
J6
J9
J20
J21
J19 J67
J7
J69 J68
J12
K3
J11
J13 J14
J15
J10
J24
ZONE 2
J25
ZONE 3
J23
ZONE 1
J26
ZONE 4
C58
C57
K2
GFCI
TRIP
J8
Q32
HEATER
J60
J66
J55
J54
J38
J53
J45
J46
J47
J41
J58
J42
J31
J32
J33
J40
J64
J36
J35
1
2
3
4
S1
FUSE CIRC/
OZONE
STATUS
INDICATOR
230 VAC 1X16A/1x20A,
(1X20A, 1X32A
NEEDS JUMPER
ADJUST PER TABLE)
GRN
PUMP 1
CIRC PUMP
4-WIRE CONNECTION
50HZ 2-PHASE SERVICE
HI-LIMIT
SENSOR
L2L1
BROWN
BRAUN
BRUN
L1
BLUE
BLAU
BLEU
BLUE
BLAU
BLEU
L2
BROWN
BRAUN
BRUN
L1 (BLU)L2 (BRN) L2 (BRN) L1 (BLU)
WI-FI
CONTROL
PANEL
FLOW SENSOR
WATER
SENSOR
FOOTWELL
LIGHT
BLUEWAVE
STEREO
(OPTIONAL)
LIGHTING
EXPANSION
CLEARRAY
STEREO POWER
SUPPLY (OPTIONAL)
PUMP 2
SERVICE 2
SERVICE 1
see section 18.3
for dip switch
settings
1
2
3
4
5
6
7
8
9
10
Page 79
Page 73
18.3 Dip Switch Settings
The dip switches are at the S1 location on the board.
A. Switch settings for Domestic 60Hz Models
BREAKER
DIP SWITCH NUMBER
1 2 3 4 5 6 7 8 9 10
40A OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
50A* OFF OFF ON OFF OFF OFF OFF OFF OFF OFF
60A OFF OFF OFF ON OFF OFF OFF OFF OFF OFF
*50A is the factory default setting
B. Switch settings for Export 50Hz Models
BREAKER
DIP SWITCH NUMBER
1 2 3 4 5 6 7 8 9 10
1x20A ON OFF OFF ON ON OFF OFF OFF OFF OFF
1x16A/
1x20A*
ON OFF ON OFF ON OFF OFF OFF OFF OFF
1x32A ON OFF ON ON OFF OFF OFF OFF OFF OFF
3x16A ON OFF OFF ON OFF OFF OFF OFF OFF OFF
*1x16A/1x20A is the factory default setting
DOMESTIC DIP SWITCH SETTINGS
S1 LOCATION
40A
50A
(factory default)
60A
1
2
3
4
5
6
7
8
9
10
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ONOFF
1
2
3
4
5
6
7
8
9
10
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ONOFF
1
2
3
4
5
6
7
8
9
10
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ONOFF
EXPORT DIP SWITCH SETTINGS S1 LOCATION
1x20A 1x16A/1x20A
(factory default)
1x32A
1
2
3
4
5
6
7
8
9
10
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ONOFF
1
2
3
4
5
6
7
8
9
10
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ONOFF
1
2
3
4
5
6
7
8
9
10
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
ONOFF
3x16A
1
2
3
4
5
6
7
8
9
10
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ONOFF
Page 80
Page 74
Single Service
1x20A This setting will turn the heater off any time either one of
the pumps are activated.
1x32A This setting is for all two pump model spas. Both pumps
and the heater will be allowed to operate at the same
time.
Dual Service (default setting)
1x16A/1x20A This setting is for all two pump model spas. Both pumps
and the heater will be allowed to operate at the same
time.
Three Phase Service
3x16A This setting is for all two pump model spas. Both pumps
and the heater will be allowed to operate at the same
time.
Page 81
Page 75
18.4 Dual Service 50Hz Connection
The factory setting for export models is for dual service breakers. The
jumper wiring is shown below. The extra White wire is not used for this
setting.
TB1
4
3
2
1
BLU
BRN
BRN
DUAL SERVICE
PARTIAL VIEW OF THE CIRCUIT BOARD
J65
J51 J3
J52
J49
J59
J44
J48
J28
J30
J37
J60
J66
J55
J54
J38
J53
J45
J46
J47
J41
J58
J42
J31
J32
J33
J40
J64
J36
J35
BLU
Heater/Transformer (Service 1)
All other components (Service 2)
1
2
A
A
B
B
3
Terminal Breaker at location:
GRN
JUMPER WIRING
Two Phase Connection Wiring
Wire From To
1 J33 J51
2 J59 J38
3 J37 J53
Page 82
Page 76
18.5 Single Service 50Hz Connection
An optional setting for export models is for a single service breaker. The
jumper wiring is shown below. Additionally, the included extra White wire
(1*) must be installed.
TB1
4
3
2
1
BLU
BRN
SINGLE
SERVICE
PARTIAL VIEW OF THE CIRCUIT BOARD
J65
J51 J3
J52
J49
J59
J44
J48
J28
J30
J37
J60
J66
J55
J54
J38
J53
J45
J46
J47
J41
J58
J42
J31
J32
J33
J40
J64
J36
J35
1*
2
3
4
All components (Service 1)
A
A
Terminal Breaker at location:
JUMPER WIRING
Single Phase Connection Wiring
Wire From To
1* J33 J47
2 J59 J41
3 J36 J37
4 J46 J51
*Extra connection must be made
Page 83
Page 77
18.6 Three Phase Service 50Hz Connection
Optional three-service breaker for export models. The jumper wiring is
shown below. The extra White wire is not used for this setting.
TB1
4
3
2
1
J51
J3
J49
J59
J44
J37
J38
J53
J60
J66
J45
J46
J47
J41
J58
J42
J31
J32
J33
J40
J64
J36
J35
1
2
3
4
GRN
BRN
BRN
BLU
BRN
THREE SERVICE
J65
J4
1
2
3
Heater/Transformer (Service 1)
Pump 1 and all other components (Service 3)
Pump 2 (Service 2)
AB C
Terminal Breaker at location:
A
B
C
JUMPER WIRING
Two Phase Connection Wiring
Wire From To
1 J38 J51
2 J59 J41
3 J36 J37
Page 84
Page 78
Loading...