WHIRLPOOL BATH SERIES
TECHNICAL SPECIFICATIONS MANUAL
HD85000
Jacuzzi® Luxury Bath
14525 Monte Vista Avenue
Chino, CA 91710
1-800-288-4002
www.jacuzzi.com
English
Technical Specifi cations Manual
Page 2
www.jacuzzi.com Technical Specifi cations
Technical Specifi cations Manual
Product Information
Save these instructions for future use. Use the form below to record your model and serial number for future
reference.
Date Purchased
Purchased From
Installed By
Serial Number
Model
Installer: Leave the manual for the homeowner.
Homeowner: Read this manual and keep for future reference.
Technical Specifi cations
Read complete instructions before beginning installation.
English
Each bathtub arrives ready for installation, completely equipped with blower motor, pump/motor assembly, heater, and
plumbing necessary for operation.
Remove the bathtub from the carton. Retain the shipping carton until satisfactory inspection of the product has been
made. Do not lift the bathtub by the plumbing or wiring at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the
fi nish, do not install the bathtub. Damage or defect to the fi nish claimed after the bathtub is installed is excluded from
the warranty.
Jacuzzi Luxury Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the
carrier. Refer any claims for damage to the carrier. For defi nitions of warranty coverage and limitations, refer to the
published warranty information packed with the product.
All bathtub units are factory tested for proper operation and watertight connections prior to shipping.
Prior to installation, the bathtub must be fi lled with water and operated to check for leaks that may have resulted
from shipping damage or mishandling. Jacuzzi Luxury Bath is not responsible for any defect that could have
been discovered, repaired, or avoided by following this inspection and testing procedure.
Technical Specifi cations
www.jacuzzi.com Page 3
Technical Specifi cations Manual
/
16
15
/
16
15
Acero™ Whirlpool Bath
Specifi cations for 6636 and 7242
6636 7242
Letter Description English Metric English Metric
Drain/Motor Location Center drain/Right end motor Center drain/Right end motor
-
English
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
Cutout Template Provided P/N HQ06000
-
64" x 34" Drop-In Cutout
Total Weight 1042 lbs 474 kg 1266 lbs 574 kg
-
Floor Loading 63.4 lb/ft
-
Operating Gallons (Min/Max) 44G/ 78G 166.7L / 295L 57G/104G 216L/394L
-
Product Weight 142 lbs 65 kg 150 lbs 68 kg
-
Outer Length 65¾" 1670mm 72" 1829mm
L
Outer Width 36" 914mm 42" 1067mm
W
Overall Height 25" 635mm 25" 635mm
H
Overfl ow Height 17⅞" 454mm 17⅞" 454mm
A
Long Edge to Drain Center
B
Short Edge to Drain Center 33" 838mm 36" 915mm
C
Drain Shoe Length 7⅞" 200mm 7⅞" 200mm
D
Deck Height 2" 51mm 2" 51mm
E
Deck Width 4" 102mm 4" 102mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 12" x 4" 305mm x 102mm 12" x 4" 356mm x 102mm
I
2
15
/
16
"
11
309 kg/m
303mm
2
Template Provided P/N HQ46000
70" x 40" Drop-In Cutout
2
60.3 lb/ft
15
/
16
11
"
294.4 kg/m
303mm
2
KEY DIMENSIONS
L
Motor
3"
F
Heater
Control Panel
W
(Motor)
H
(Heater)
W
Overfl ow
C
L
(Motor)
(Heater)
Suction
Fitting
I
E
(G) Service
Access
Note: Drain installation
is non-standard. Vertical
overfl ow connection
requires offset.
A
Page 4
D
B
Side View End View Drain/Overfl ow
www.jacuzzi.com Technical Specifi cations
Technical Specifi cations Manual
/
16
15
/
16
15
/
16
15
Allusion™ Whirlpool Bath
Specifi cations for 6636, 7236 and 7242
6636 7236 7242
Letter Description English Metric English Metric English Metric
Drain/Motor Location Center drain/Right end motor Center drain/Right end motor Center drain/Right end motor
-
Cutout Template Template provided P/N BY20000 Template provided P/N BY20000 Template provided P/N BY20000
-
Total Weight 1015 lbs 461 kg 1138 lbs 517 kg 1251 lbs 588 kg
-
Floor Loading 61.5 lb/ft
-
Operating Gallons (Min/Max) 56G / 75G 208L / 284L 61G / 83G 231L / 314L 74G / 95G 280L / 360L
-
Product Weight 140 lbs 64 kg 147 lbs 67 kg 160 lbs 73 kg
-
Outer Length 66" 1676mm 72" 1829mm 72" 1829mm
L
Outer Width 36" 914mm 36" 915mm 42" 1067mm
W
Overall Height 26" 660mm 26" 660mm 26" 660mm
H
Overfl ow Height 17⅜" 441mm 17⅜" 441mm 17⅜" 441mm
A
Long Edge to Drain Center
B
Short Edge to Drain Center 33" 838mm 36" 914mm 36" 914mm
C
Drain Shoe Length 6" 152mm 6" 152mm 6" 152mm
D
Deck Height 4" 102mm 4" 102mm 4" 102mm
E
Deck Width 3⅞" 97mm 3⅞" 97mm 3⅞" 97mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 12" x 4" 305mm x 102mm 12" x 4" 305mm x 102mm 12" x 4" 305mm x 102mm
I
2
15
/
16
11
"
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
300 kg/m
302mm
2
63.2 lb/ft
15
/
16
11
2
"
308 kg/m
305mm
2
59.6 lb/ft
15
/
16
11
2
301.1 kg/m
"
English
2
305mm
KEY DIMENSIONS
L
F
Motor
3"
W
Overfl ow
Suction Fitting
4"
L
E
(Motor)
(Heater)
I
Control
Panel
Heater
(G) Secondary
Service Access
H
C
W
(Motor)
(G) Primary
Service Access
Motor Extends
2" Beyond Lip
A
Technical Specifi cations
D
B
Side View End View Drain/Overfl ow
www.jacuzzi.com Page 5
Technical Specifi cations Manual
Bellavista™ Whirlpool Bath
Specifi cations for 6042, 6642 and 7242
6042 6642 7242
Letter Description English Metric English Metric English Metric
-
English
-
-
-
-
-
L
W
H
A
B
C
D
E
F
G
I
Drain/Motor
Location
Cutout Template Template Provided P/N P187000 Template Provided P/N P187000 Template Provided P/N P187000
Total Weight 1041 lbs 473 kg 1113 lbs 506 kg 1233 lbs 560 kg
Floor Loading 60.1 lb/ft
Operating Gallons
(Min/Max)
Product Weight 141 lbs 64 kg 130 lbs 59 kg 142 lbs 65 kg
Outer Length 59¾" 1518mm 66" 1676mm 72" 1829mm
Outer Width
Overall Height
Overfl ow Height
Long Edge to
Drain Center
Short Edge to
Drain Center
Drain Shoe Length
Deck Height
Deck Width
Service Access
Dimensions
Floor Cutout for
Drain
Center drain/Right end motor Center drain/Right end motor
2
63G / 78G 238.5L / 295L 69G / 88G 261.2L / 333L 84G / 95G 318L / 360L
41¾
"
26
"
20
"
11¾
"
32½
"
6
"
2
"
3
"
12
17
" x 18"
" x 4"
305mm x 457mm
432mm x 102mm
2
293 kg/m
1060mm 42" 1067mm 42" 1067mm
660mm 26" 660mm 26" 660mm
508mm
298mm
826mm 35½" 902mm 36" 914mm
152mm
51mm
76mm
57.8 lb/ft
20
"
11¾
6
"
2
"
3
"
12
" x 18"
17
" x 4"
2
"
282 kg/m
508mm
298mm
152mm
51mm
76mm
305mm x 457mm
432mm x 102mm
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
Center drain/Right or Left end motor
2
58.7 lb/ft
20
"
11¾
6
"
2
"
3
"
12
" x 18"
17
" x 4"
2
"
2
286 kg/m
508mm
298mm
152mm
51mm
76mm
305mm x 457mm
432mm x 102mm
KEY DIMENSIONS
Bellavista RH 6042 & 6646
L
F
Motor
W
Suction Fitting
Bellavista RH 6042 & 6646
Side View
Overfl ow
10.5"
L
(Heater)
3"
I
Control
Panel
(G) Secondary
Service Access
(Motor)
C
Heater
E
H
(G) Primary
Service Access
W
(Motor)
End View
(G) Primary
Service Access
(G) Secondary
Service Access
A
D
B
Drain/Overfl ow
Bellavista LH 7242
Motor
Suction
Fitting
Heater
Control
Panel
Bellavista RH 7242
Bellavista LH 7242
E
(Heater)
(Motor)
L
F
3"
10.5"
L
Side View
I
L
Overfl ow
C
(Heater)
Bellavista RH 7242
W
W
Suction Fitting
E
(Motor)
L
F
Motor
Overfl ow
Heater
3"
I
Control
Panel
10.5"
H
(Motor)
End View
C
W
(Motor)
W
(G) Primary
Service
Access
(G) Secondary
Service
Access
A
D
B
A
H
Drain/Overfl ow
D
B
Page 6
www.jacuzzi.com Technical Specifi cations
Technical Specifi cations Manual
Bellavista™ Whirlpool Bath
Specifi cations for 6060
6060
Letter Description English Metric
Drain/Motor
-
Location
Cutout Template Template Provided P/N P654000
-
Total Weight 1226 lbs 557 kg
-
Floor Loading 49.5 lb/ft
-
Operating Gallons
-
(Min/Max)
Product Weight 160 lbs 73 kg
-
Outer Length 59¾" 1518mm
L
Outer Width 59¾" 1518mm
W
Overall Height 25" 635mm
H
Overfl ow Height
A
Long Edge to
B
Drain Center
Short Edge to
C
Drain Center
Drain Shoe Length
D
Deck Height
E
Deck Width
F
Service Access
G
Dimensions
Floor Cutout for
I
Drain
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
Center drain/Right or Left side motor
2
80G / 92G 302.8L / 348L
18
⅞"
14
"
9
/
16
34 " 879mm
7½
"
2
"
6
"
12
12
" x 18"
" x 4"
305mm x 457mm
305mm x 102mm
242 kg/m
479mm
356mm
191mm
51mm
152mm
2
English
KEY DIMENSIONS
Bellavista RH 6060 Bellavista LH 6060 Bellavista RFM 6060
Heater
(Heater)
Control
Panel
WL
Suction
Fitting
H
Overfl ow
A
B
A
Motor
D
D
B
3"
I
F
3"
Bellavista RFM 6060
C
(G) Service Access
L
E
(Motor)
Control
Panel
H
Control
Panel
L
Overfl ow
Bellavista RH 6060
Bellavista LH 6060
E
(Motor)
Front View Side View Drain/Overfl ow
L
(Heater)
(Heater)
W
(G) Primary
Service Access
Suction
Fitting
Motor
3"
I
(G) Secondary
Service Access
H
(Heater)
C
Heater
W
(Motor)
W
(Motor)
F
3"
E
(Motor)
L
L
Overfl ow
(Motor)
3"
W
(Heater)
Suction
Fitting
Heater
F
I
W
C
Motor
A
D
B
Drain/Overfl ow
Technical Specifi cations
www.jacuzzi.com Page 7
Technical Specifi cations Manual
Cortina™ Whirlpool Bath
Specifi cations for 7272
7272
Letter Description English Metric
Drain/Motor
-
English
Location
Cutout 70" Dia. Drop-In Cutout
-
Total Weight 1485 lbs 674 kg
-
Floor Loading 41.2 lb/ft
-
Operating Gallons
-
(Min/Max)
Product Weight 210 lbs 95 kg
-
Outer Length 72" 1829mm
L
Outer Width 72" 1829mm
W
Overall Height 22¼" 565mm
H
Overfl ow Height 16¾" 425mm
A
Long Edge to
B
Drain Center
Short Edge to
C
Drain Center
Drain Shoe Length 5" 127mm
D
Deck Height 2½" 64mm
E
Deck Width 6½" 165mm
F
Service Access
G
Dimensions
Floor Cutout for
I
Drain
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
Center drain/Right motor
2
201.1 kg/m
87G / 117G 329L / 443L
19¼" 489mm
24½" 622mm
12" x 18" 305mm x 457mm
14" x 4" 356mm x 102mm
2
KEY DIMENSIONS
H
Side View End View Drain/Overfl ow
L
F
Suction
Fitting
Heater
W
L
(Motor)
(Heater)
(Motor)
Overfl ow
(Heater)
3"
I
Control
Panel
C
L
(G) Service
Access
Motor
E
A
D
B
Page 8
www.jacuzzi.com Technical Specifi cations
Technical Specifi cations Manual
Duetta™ Whirlpool Bath
Specifi cations for 6042, 6636, 6642 and 7242
6042 6636 72426642
Letter Description English Metric English Metric English Metric English Metric
Drain/Motor
-
Location
Cutout Template Template Provided P/N DA09000 Template Provided P/N DA08000 Template Provided P/N DA07000 Template Provided P/N DA06000
-
Total Weight 1077 lbs 490 kg 1044 lbs 475 kg 1195 lbs 543 kg 1293 lbs 588 kg
-
Floor Loading 61.6 lb/ft
-
Operating Gallons
-
(Min/Max)
Product Weight 136 lbs 62 kg 136 lbs 62 kg 137 lbs 62 kg 143 lbs 65 kg
-
Outer Length 60" 1524mm 66" 1676mm 66" 1829mm 72" 1829mm
L
Outer Width 42" 1067mm 36" 915mm 42" 1067mm 42" 1067mm
W
Overall Height 26" 660mm 26" 660mm 26" 660mm 26" 660mm
H
Overfl ow Height 18⅜" 467mm 18⅜" 467mm 18⅜" 467mm 18⅜" 467mm
A
Long Edge to
B
Drain Center
Short Edge to
C
Drain Center
Drain Shoe Length 7¼" 183mm 7¼" 183mm 7¼" 183mm 7¼" 183mm
D
Deck Height ½" 13mm ½" 13mm ½" 13mm ½" 13mm
E
Deck Width 3⅞" 98mm 3⅞" 98mm 3⅞" 98mm 3⅞" 98mm
F
Service Access
G
Dimensions
Floor Cutout for
I
Drain
Center drain/Right end motor Center drain/Right end motor Center drain/Right end motor Center drain/Right end motor
2
70G / 83G 265L / 314L 75G / 79G 283.9L / 299L 90G / 97G 340.7L / 367L 97G / 108G 367.2L / 409L
11" 279mm 11" 279mm 11" 279mm 11" 279mm
30" 762mm 33" 838mm 33" 838mm 36" 915mm
12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm
13" x 4" 330mm x 102mm 13" x 4" 330mm x 102mm 13" x 4" 330mm x 102mm 13" x 4" 330mm x 102mm
301 kg/m
2
63.3 lb/ft
2
309 kg/m
2
62.1 lb/ft
2
303 kg/m
2
61.6 lb/ft
2
301 kg/m
English
2
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
KEY DIMENSIONS
Duetta 6042 & 6642
W
Suction Fitting
(Heater)
Side View End View Drain/Overfl ow Side View End View Drain/Overfl ow
L
Motor
(G) Service
Control
Panel
L
(Motor)
I
Heater
3"
F
Overfl ow
C
W
E
(Heater)
H
(Motor)
Access
Motor Extends
3" Beyond Lip
A
D
B
Duetta 6636 & 7242
W
Control
Panel
Suction Fitting
L
(Heater)
L
Motor
(G) Service
Access
I
Overfl ow
E
(Motor)
F
Heater
H
C
Note: Drain installation
is non-standard. Vertical
overfl ow connection
requires offset.
W
(Heater)
(Motor)
Motor Extends
3" Beyond Lip
A
3"
D
B
Technical Specifi cations
www.jacuzzi.com Page 9
Technical Specifi cations Manual
Elara™ Whirlpool Bath
Specifi cations for 6042, 6636 and 7242
6042
Letter Description English Metric English Metric English Metric
Drain/Motor Location End drain/Right or Left end motor End drain/Right or Left end motor End drain/Right or Left end motor
English
-
Cutout Template Provided P/N DQ50000
-
Template Provided P/N DQ51000
58" x 40" Drop-In Cutout
Total Weight 1168 lbs 531 kg 1133 lbs 515 kg 1388 lbs 631 kg
-
Floor Loading 66.7 lb/ft
-
Operating Gallons (Min/Max) 83G/ 94G 314.2L / 356L 78G/ 89G 295.3L / 337L 107G/ 117G 405L / 443L
-
Product Weight 135 lbs 61 kg 142 lbs 65 kg 163 lbs 74 kg
-
Outer Length 60" 1524mm 66" 1676mm 72" 1829mm
L
Outer Width 42" 1067mm 36" 915mm 42" 1067mm
W
Overall Height 26" 660mm 26˝ 660mm 26˝ 660mm
H
Overfl ow Height 18½" 470mm 18½" 470mm 18½" 470mm
A
Long Edge to Drain Center 10⅝" 269mm 10⅝" 269mm 10⅝" 269mm
B
Short Edge to Drain Center 21" 533mm 18" 457mm 21" 533mm
C
Drain Shoe Length 6" 152mm 6" 152mm 6" 152mm
D
Deck Height ½" 13mm ½" 13mm ½" 13mm
E
Deck Width 4¼" 107mm 4¼" 107mm 4¼" 107mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 12" x 4" 305mm x 102mm 12" x 4" 305mm x 102mm 12" x 4" 305mm x 102mm
I
2
325 kg/m
2
68.7 lb/ft
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
6636 7242
64" x 34" Drop-In Cutout
2
335 kg/m
2
Template Provided P/N BZ50000
70" x 40" Drop-In Cutout
2
66.1 lb/ft
323 kg/m
2
KEY DIMENSIONS
Elara RH
Motor
(G) Primary
Service
Access
W
Heater
E
(Motor)
(Heater)
L
L
Control
Panel
(G) Secondary
Service Access
I
3"
Suction Fitting
Elara LH
L
C
F
C
Overfl ow
Overfl ow
H
F
Suction Fitting
(Motor)
I
Control
3"
W
Panel
(G) Secondary
Service Access
(Heater)
A
Motor
(G) Primary
Service
W
Access
Heater
Page 10
Side View
D
B
Drain/Overfl owEnd View
www.jacuzzi.com Technical Specifi cations
Technical Specifi cations Manual
Fuzion™ Whirlpool Bath
Specifi cations for 7236 and 7242
7236 7242
Letter Description English Metric English Metric
Drain/Motor Location End drain/Right or Left end motor Center drain/Right end motor
-
Cutout Template Provided P/N DD42000
-
69" x 33" Drop-In Cutout
Total Weight 1210 lbs 550 kg 1324 lbs 602 kg
-
Floor Loading 69.6 lb/ft
-
Operating Gallons (Min/Max) 77G / 99G 291.5L / 375L 82G / 108G 310.4L / 409L
-
Product Weight 135 lbs 61 kg 174 lbs 79 kg
-
Outer Length 70¾" 1797mm 72" 1829mm
L
Outer Width 35½" 902mm 42" 1067mm
W
Overall Height 24" 610mm 24" 610mm
H**
Overfl ow Height 17" 432mm 17" 432mm
A
Long Edge to Drain Center 10¼" 260mm 10¼" 260mm
B
Short Edge to Drain Center 17 " 447mm 36" 914mm
C
Drain Shoe Length 7" 178mm 8½" 216mm
D
Deck Height 4" 102mm 4" 102mm
E**
Deck Width 3" 76mm 3½" 89mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 12" x 4" 305mm x 102mm 18½" x 4" 470mm x 102mm
I
2
11
/
16
340 kg/m
2
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
Template Provided P/N GR23000
70" x 40" Drop-In Cutout
63 lb/ft
2
307 kg/m
2
English
KEY DIMENSIONS
Fuzion LH 7236
C
F
Fuzion RH 7236
(G) Service
Access
W
Heater
Fuzion LH 7236
Overfl ow
I
3"
L
(Motor)
L
Suction Fitting
Motor
Suction Fitting
Control
Panel
Fuzion 7242
(G) Service
Motor
Control
Panel
Heater
L
Overfl ow
I
3"
F
W
E
(Heater)
H**
(Motor)
Access
W
W
C
Overfl ow
E
A
Control
Panel
L
(Heater)
I
(Motor)
L
Motor
(G) Service
Suction
Fitting
3"
F
Heater
C
Note: Drain included.
Non-standard installation,
refer to manual.
W
H**
(Motor)
Access
A
(Motor)
**Height of tub only, optional wood frame adds 1.25"
Technical Specifi cations
D
B
End ViewSide View
Drain/Overfl ow
End View
D
B
Drain/Overfl owSide View
www.jacuzzi.com Page 11
Fuzion™ Whirlpool Bath
Specifi cations for 6666
Letter Description English Metric
Drain/Motor Location Center drain/Right or Left side motor
-
English
Cutout Template Provided P/N DD43000
-
See Drop-In Diagram
Total Weight 1773 lbs 806 kg
-
Floor Loading 59.1 lb/ft
-
Operating Gallons (Min/Max) 119G / 148G 451L / 560L
-
Product Weight 190 lbs 86 kg
-
Outer Length 65¾" 1670mm
L
Outer Width 65¾" 1670mm
W
Overall Height 24" 610mm
H**
13
/
Overfl ow Height 16 " 427mm
A
Long Edge to Drain Center 12 " 308mm
B
Short Edge to Drain Center 40 " 1039mm
C
Drain Shoe Length 9¼" 234mm
D
Deck Height 4" 102mm
E**
Deck Width 3½" 89mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 20" x 4" 508mm x 102mm
I
16
1
/
8
15
/
16
Technical Specifi cations Manual
6666
2
288 kg/m
2
Fuzion 6666 Drop-In Cutout
63 3/4" 63 3/4"
31 9/16"
C
L
45 1/2"
11 1/2"
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
KEY DIMENSIONS
Fuzion RH 6666 Fuzion LH 6666
C
LW
Motor
3"
I
(G) Service
F
Heater
Suction Fitting
L
E
(Motor)
Control
Panel
Overfl ow
Access
(G) Service
Access
(Heater)
W
(Motor)
W
Overfl ow
Control Panel
Motor
3"
I
Heater
H**
C
F
Suction Fitting
L
Note: Drain included.
Non-standard installation,
refer to manual.
A
Side View
**Height of tub only, optional wood frame adds 1.25"
Page 12
D
B
Drain/Overfl owEnd View
www.jacuzzi.com Technical Specifi cations
Technical Specifi cations Manual
Fuzion™ Whirlpool Bath
Specifi cations for 7260
7260
Letter Description English Metric
Drain/Motor Location Center drain/Right or left side motor
-
Cutout Template Provided P/N DD44000
-
70" x 58" Drop-In Cutout
Total Weight 1790 lbs 811 kg
-
Floor Loading 60.1 lb/ft
-
Operating Gallons (Min/Max) 110G/ 148G 417L / 560L
-
Product Weight 207 lbs 94 kg
-
Outer Length 71¾" 1822mm
L
Outer Width 59¾" 1518mm
W
Overall Height 24" 610mm
H**
Overfl ow Height 16¾" 425mm
A
Long Edge to Drain Center 12 " 306mm
B
Short Edge to Drain Center 36" 915mm
C
Drain Shoe Length 8½" 216mm
D
Deck Height 4" 102mm
E**
Deck Width 3½" 89mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 18½" x 4" 470mm x 102mm
I
2
1
/
16
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
293 kg/m
2
English
KEY DIMENSIONS
Fuzion RH 7260
W
3"
I
F
Overfl ow
Fuzion RH 7260
E
Control
Panel
Side View Drain/Overfl ow
L
Heater
L
(Heater)
Motor
Suction
Fitting
Fuzion LH 7260
(G) Secondary
Service Access
L
(G) Primary
Service Access
(G) Primary
Service Access
(G) Secondary
C
Service Access
(Motor)
H**
(Heater)
W
F
Overfl ow
W
(Motor)
End View
Heater
Motor
I
3"
Suction
Fitting
Control Panel
C
Note: Drain included.
Non-standard installation,
refer to manual.
A
D
B
**Height of tub only, optional wood frame adds 1.25"
Technical Specifi cations
www.jacuzzi.com Page 13
Technical Specifi cations Manual
Fuzion™ Whirlpool Bath
Specifi cations for 7260 DUAL ZONE
7260
Letter Description English Metric
Drain/Motor Location Center drain/Right and left side motor
-
English
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 230V 20A 60HZ (2X)
Heater 120V 15A 60HZ (2X)
Cutout Template Provided P/N DD44000
-
70" x 58" Drop-In Cutout
Total Weight 1825 lbs 829 kg
-
Floor Loading 61.3 lb/ft
-
Operating Gallons (Min/Max) 110G/ 148G 417L / 560L
-
Product Weight 242 lbs 110 kg
-
Outer Length 71¾" 1822mm
L
Outer Width 59¾" 1518mm
W
Overall Height 24" 610mm
H**
Overfl ow Height 16¾" 425mm
A
Long Edge to Drain Center 12 " 306mm
B
Short Edge to Drain Center 36" 915mm
C
Drain Shoe Length 8½" 216mm
D
Deck Height 4" 102mm
E**
Deck Width 3½" 89mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 18½" x 4" 470mm x 102mm
I
2
1
/
16
299.1 kg/m
2
KEY DIMENSIONS
Fuzion Dual 7260
E
Side View Drain/Overfl ow
(G) Primary
Service Access
L
(Heater)
W
(Motor)
Overfl ow
(G) Secondary
Service Access
L
Heater
Motor
Motor
3"
Suction
H**
(Heater)
Fitting
Heater
C
W
(Motor)
End View
I
F
Control
Panel
(G) Secondary
Service Access
(G) Secondary
Service Access
Note: Drain included.
Non-standard installation,
refer to manual.
A
D
B
**Height of tub only, optional wood frame adds 1.25"
Page 14
www.jacuzzi.com Technical Specifi cations
Technical Specifi cations Manual
Mio™ Whirlpool Bath
Specifi cations for 6636 and 7242
6636
Letter Description English Metric English Metric
Drain/Motor Location Center drain/Right end motor Center drain/Right end motor
-
Cutout Template Template Provided P/N HQ96000 Template Provided P/N HR36000
-
Total Weight 961 lbs 436 kg 1125 lbs 511 kg
-
Floor Loading 58.2 lb/ft
-
Operating Gallons (Min/Max) 48G/ 70G 181.7L / 265L 54G/ 87G 204L/ 329L
-
Product Weight 128 lbs 58 kg 150 lbs 68 kg
-
Outer Length 66" 1676mm 72" 1829mm
L
Outer Width 36" 915mm 42" 1067mm
W
Overall Height 25" 635mm 25" 635mm
H
Overfl ow Height 17⅞" 454mm 17⅞" 454mm
A
Long Edge to Drain Center 13 " 340mm 13 " 340mm
B
Short Edge to Drain Center 33" 838mm 36" 915mm
C
Drain Shoe Length 6⅞" 173mm 6⅞" 173mm
D
Deck Height 2" 51mm 2" 51mm
E
Deck Width 6⅝" 168mm 6⅝" 168mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 12" x 4" 305mm x 102mm 12" x 4" 305mm x 102mm
I
2
7
/
16
284 kg/m
2
53.6 lb/ft
7242
2
7
/
16
261.5 kg/m
English
2
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
KEY DIMENSIONS
L
Motor
W
Suction Fitting
L
I
C
E
Heater
3"
F
Control Panel
Overfl ow
W
(G) Service
Access
Motor Extends
3" Beyond Lip
Note: Drain installation
is non-standard. Vertical
overfl ow connection
requires offset.
Side View Drain/Overfl ow
Technical Specifi cations
(Heater)
(Motor)
H
(Motor)
End View
A
D
B
www.jacuzzi.com Page 15
Reàl™ Whirlpool Bath
Specifi cations for 7242
Letter Description English Metric
Drain/Motor Location Center drain/Right end motor
-
English
Cutout 70" x 40" Drop-In Cutout
-
Total Weight 1180 lbs 536 kg
-
Floor Loading 56.2 lb/ft
-
Operating Gallons (Min/Max) 84G/ 95G 318L / 360L
-
Product Weight 139 lbs 63 kg
-
Outer Length 72" 1829mm
L
Outer Width 42" 1067mm
W
Overall Height 26" 660mm
H
Overfl ow Height 20" 508mm
A
Long Edge to Drain Center 14" 356mm
B
Short Edge to Drain Center 36" 914mm
C
Drain Shoe Length 8¾" 222mm
D
Deck Height 2" 51mm
E
Deck Width 3" 76mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 18" x 4" 457mm x 102mm
I
Technical Specifi cations Manual
7242
2
274 kg/m
2
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
KEY DIMENSIONS
L
F
W
Suction Fitting
L
Overfl ow
E
Motor
3"
I
Heater
Control
Panel
C10.5"
(G) Primary
Service Access
(G) Secondary
Service Access
W
Page 16
(Motor)
(Heater)
Side View End View
H
(Heater)
(Motor)
www.jacuzzi.com Technical Specifi cations
A
Drain/Overfl ow
D
B
Technical Specifi cations Manual
Sabella™ Whirlpool Bath
Specifi cations for 7247
7247
Letter Description English Metric
Drain/Motor Location Center drain/Right end motor
-
Cutout Template Template Provided P/N P187000
-
Total Weight 1320 lbs 600 kg
-
Floor Loading 56.2 lb/ft
-
Operating Gallons (Min/Max) 97G / 109G 368L / 413L
-
Product Weight 162 lbs 74 kg
-
Outer Length 72" 1829mm
L
Outer Width 47" 1194mm
W
Overall Height 26½" 673mm
H
Overfl ow Height 20" 508mm
A
Long Edge to Drain Center 14" 356mm
B
Short Edge to Drain Center 36" 915mm
C
Drain Shoe Length 6¾" 171mm
D
Deck Height 2" 51mm
E
Deck Width 3" 76mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 18" x 4" 457mm x 102mm
I
2
274 kg/m
English
2
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
KEY DIMENSIONS
L
F
W
3"
I
Overfl ow
C
L
10.5"
Motor
Suction
Fitting
Control Panel
Heater
W
(G) Service
Access
Technical Specifi cations
(Heater)
(Motor)
E
H
(Heater)
(Motor)
A
D
B
Drain/Overfl owEnd ViewSide View
www.jacuzzi.com Page 17
Salerno™ Whirlpool Bath
Specifi cations for 6636 and 7242
6636
Letter Description English Metric English Metric
Drain/Motor Location Center drain/Right end motor Center drain/Right end motor
-
English
Cutout Template Template Provided P/N GX46000 Template Provided P/N HA76000
-
Total Weight 920 lbs 418 kg 1160 lbs 527 kg
-
Floor Loading 55.8 lb/ft
-
Operating Gallons (Min/Max) 59G / 62G 223.3L / 235L 84G / 89G 318L / 337L
-
Product Weight 154 lbs 70 kg 169 lbs 77 kg
-
Outer Length 66" 1676mm 72" 1829mm
L
Outer Width 36" 915mm 42" 1067mm
W
Overall Height 25" 635mm 25" 635mm
H
Overfl ow Height 17 " 443mm 17 " 443mm
A
Long Edge to Drain Center 11 " 294mm 11 " 294mm
B
Short Edge to Drain Center 33" 838mm 36" 915mm
C
Drain Shoe Length 6½" 165mm 6½" 165mm
D
Deck Height 3" 76mm 3" 76mm
E
Deck Width 5" 127mm 5" 127mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 12" x 4" 305mm x 102mm 12" x 4" 305mm x 102mm
I
2
7
/
16
9
/
16
272 kg/m
2
55.3 lb/ft
7
/
16
9
/
16
2
7242
270 kg/m
Technical Specifi cations Manual
2
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
KEY DIMENSIONS
L
Motor
Control
H
Panel
3"
F
Heater
W
(Heater)
W
Overfl ow
C
L
(Motor)
(Heater)
Suction
Fitting
E
I
(G) Service
Access
Motor Extends
3" Beyond Lip
Note: Drain installation
is non-standard. Vertical
overfl ow connection
requires offset.
A
Page 18
Side View
(Motor)
D
B
Drain/Overfl owEnd View
www.jacuzzi.com Technical Specifi cations
Technical Specifi cations Manual
Sia™ Whirlpool Bath
Specifi cations for 6636 and 7242
6636
Letter Description English Metric English Metric
Drain/Motor Location Center drain/Right end motor Center drain/Right end motor
-
Cutout Template Provided P/N GU50000
-
64" x 34" Drop-In Cutout
Total Weight 1033 lbs 470 kg 1312 lbs 596 kg
-
Floor Loading 62.6 lb/ft
-
Operating Gallons (Min/Max) 65G/ 76G 246.1L / 288L 89G/ 102G 337L / 386L
-
Product Weight 150 lbs 68 kg 162 lbs 74 kg
-
Outer Length 66" 1676mm 72" 1829mm
L
Outer Width 36" 915mm 42" 1067mm
W
Overall Height 24" 610mm 24" 610mm
H
Overfl ow Height 17¾" 451mm 17¾" 451mm
A
Long Edge to Drain Center 11½" 292mm 11½" 292mm
B
Short Edge to Drain Center 33" 838mm 36" 915mm
C
Drain Shoe Length 6½" 165mm 6½" 165mm
D
Deck Height 2" 51mm 2" 51mm
E
Deck Width 5" 127mm 5" 127mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 14" x 4" 356mm x 102mm 14" x 4" 356mm x 102mm
I
2
305 kg/m
2
Template Provided P/N GU50000
62.5 lb/ft
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
7242
70" x 40" Drop-In Cutout
2
305 kg/m
2
English
KEY DIMENSIONS
L
Side View End View Drain/Overfl ow
W
(Heater)
(Motor)
Overfl ow
L
(G) Service
Motor
3"
I
C
E
6"
Suction
Fitting
F
Control
Panel
(Heater) (Motor)
H
Heater
W
Access
A
D
B
Technical Specifi cations
www.jacuzzi.com Page 19
Venicia™ Whirlpool Bath
Specifi cations for 7242
Letter Description English Metric
Drain/Motor Location Center drain/Right end motor
-
English
Cutout Template Template Provided P/N P187000
-
Total Weight 1198 lbs 545 kg
-
Floor Loading 57 lb/ft
-
Operating Gallons (Min/Max) 85G / 97G 322L / 368L
-
Product Weight 140 lbs 64 kg
-
Outer Length 72" 1829mm
L
Outer Width 42" 1067mm
W
Overall Height 26" 660mm
H
Overfl ow Height 20" 508mm
A
Long Edge to Drain Center 14" 356mm
B
Short Edge to Drain Center 36" 915mm
C
Drain Shoe Length 6⅞" 175mm
D
Deck Height 2" 51mm
E
Deck Width 5" 127mm
F
Service Access Dimensions 12" x 18" 305mm x 457mm
G
Floor Cutout for Drain 18" x 4" 457mm x 102mm
I
2
7242
278 kg/m
Technical Specifi cations Manual
2
Electrical Specifi cations Each component requires a seperate, dedicated GFCI protected circuit
Motor/Pump 120V 20A 60HZ
Heater 120V 15A 60HZ
KEY DIMENSIONS
L
F
Motor
W
3"
I
Overfl ow
L
E
10.5"
Suction
Fitting
Control
Panel
Heater
W
(G) Service
Access
Page 20
Side view
(Heater)
(Motor)
H
(Heater)
(Motor)
A
D
B
Drain/Overfl owEnd View
www.jacuzzi.com Technical Specifi cations
Loading...