Jacuzzi FUZION BATH SERIES 7260, FUZION Series, FUZION 7236, FUZION 7260, FUZION 6666 Installation & Operation Instructions
FUZION BATH SERIES
INSTALLA TION / OPERATION INSTRUCTIONS
Save These Instructions for Future Use.
Complete and mail-in the product registration card provided with your unit.
Write and save the model and serial number of your unit below.
Owner's Record
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Number _____________________________________________________________
Model ____________________________________________________________________
Installer: Leave this manual for homeowner.
Homeowner: Read this manual and keep for future reference.
©
2005 Jacuzzi Whirlpool Bath DE99000A 3/06
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
ENGLISH
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, IN-
CLUDING THE FOLLOWING:
DANGER: TO REDUCE THE RISK OF INJURY, DO NOT PERMIT CHILDREN T O USE THIS UNIT UNLESS
THEY ARE CLOSELY SUPERVISED AT ALL TIMES.
WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL. DO
NOT USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURER.
WARNING — NEVER DROP OR INSERT ANY OBJECT INTO ANY OPENING IN THE WHIRLPOOL BATH.
WARNING — DO NOT OPERATE THIS UNIT WITHOUT THE GUARD OVER THE SUCTION FITTING.
WARNING — THIS UNIT MUST BE CONNECTED ONLY TO A SUPPLY CIRCUIT THAT IS PROTECTED BY
A GROUND FAULT CIRCUIT INTERRUPTER (GFCI). SUCH A GFCI SHOULD BE PROVIDED BY THE
INSTALLER AND SHOULD BE TESTED ON A ROUTINE BASIS. TO TEST THE GFCI, PUSH THE TEST
BUTTON. THE GFCI SHOULD INTERRUPT POWER. PUSH THE RESET BUTTON. POWER SHOULD BE
RESTORED. IF THE GFCI FAILS TO OPERATE IN THIS MANNER, THE GFCI IS DEFECTIVE. IF THE GFCI
INTERRUPTS POWER TO THE BATHTUB WITHOUT THE TEST BUTTON BEING PUSHED, A GROUND
CURRENT FLOWING, INDICATING A POSSIBILITY OF AN ELECTRIC SHOCK. DO NOT USE THIS UNIT.
DISCONNECT THE UNIT AND HAVE THE PROBLEM CORRECTED BY A QUALIFIED SERVICE REPRESENTATIVE BEFORE USING.
WARNING: (FOR PERMANENTLY CONNECTED UNITS) A GREEN COLORED TERMINAL (OR A WIRE
CONNECTOR MARKED “G”, “GR”, “GROUND”, OR “GROUNDING”) IS PROVIDED WITHIN THE TERMINAL
COMPARTMENT. TO REDUCE THE RISK OF ELECTRIC SHOCK, CONNECT THE TERMINAL OR CONNECTOR
TO THE GROUNDING TERMINAL OF YOUR ELECTRIC SERVICE OR SUPPLY PANEL WITH A CONDUCTOR
EQUIVALENT IN SIZE TO THE CIRCUIT CONDUCTORS SUPPLY THIS EQUIPMENT.
OPERATING
WARNING — PROLONGED IMMERSION IN HOT WATER MAY INDUCE HYPERTHERMIA. HYPER THER-
MIA OCCURS WHEN THE INTERNAL TEMPERATURE OF THE BODY REACHES A LEVEL SEVERAL
DEGREES ABOVE THE NORMAL BODY TEMPERATURE OF 98.6°F. THE SYMPTOMS OF HYPER THERMIA INCLUDE AN INCREASE IN THE INTERNAL TEMPERATURE OF THE BODY, DIZZINESS, LETHARGY, DROWSINESS AND FAINTING. THE EFFECTS OF HYPERTHERMIA INCLUDE:
A) FAILURE TO PERCEIVE HEAT
B) FAILURE TO RECOGNIZE THE NEED TO EXIT THE SPA OR TUB
C) UNAWARENESS OF IMPENDING HAZARD
D) FETAL DAMAGE IN PREGNANT WOMEN
E) PHYSICAL INABILITY TO EXIT THE SPA OR HOT TUB OR
F) UNCONSCIOUSNESS RESULTING IN DANGER OF DROWNING.
WARNING — THE USE OF ALCOHOL, DRUGS OR MEDICATION CAN GREATLY INCREASE THE RISK
OF FETAL HYPERTHERMIA.
WARNING — DO NOT TAMPER WITH USER-OPERATED CONTROLS OR SUCH DEVICES.
2
Jacuzzi Whirlpool Bath DE99000A 3/06
INSTALLATION
DANGER — RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND
FAULT CIRCUIT INTERRUPTER (GFCI).
CAUTION
PERIODICALLY IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS.
WARNING
USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURERS.
WARNING
WARNING
TIMES WHEN THE HYDROMASSAGE SYSTEM IS OPERATING. HAIR LONGER THAN SHOULDER
LENGTH SHOULD BE SECURED CLOSE TO THE HEAD.
WARNING
DRYER, LAMP, TELEPHONE, RADIO OR TELEVISION) WITHIN 60" (1.5 m) OF THIS HYDROMASSAGE BATHTUB.
WARNING
BEFORE OR DURING THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID
UNCONSCIOUSNESS AND POSSIBLE DROWNING.
WARNING
CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.
WARNING
BATHTUB EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.
WARNING
EXCESS OF 104°F (40°C) MAY BE INJURIOUS TO YOUR HEALTH. CHECK AND ADJUST WATER
TEMPERATURE BEFORE USE.
WARNING
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB
EQUIPPED WITH A HEATER.
WARNING
OF FATAL HYPERTHERMIA.
— TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE
— USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL. DO NOT
— TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE BATHTUB.
— KEEP BODY AND HAIR A MINIMUM OF 6" (15,2 cm) AWAY FROM SUCTION FITTING AT ALL
— RISK OF ELECTRICAL SHOCK; DO NOT PERMIT ELECTRICAL APPLIANCES (SUCH AS HAIR
— RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE DRUGS OR ALCOHOL
— RISK OF FETAL INJURY; PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD
— RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; DO NOT USE A HYDROMASSAGE
— RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; WATER TEMPERATURE IN
— RISK OF HYPERTHERMIA; PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE
— THE USE OF ALCOHOL, DRUGS OR MEDICATION CAN GREATLY INCREASE THE RISK
ENGLISH
FOR BUILT-IN AND DROP-IN UNITS, INSTALL TO PERMIT ACCESS FOR SERVICING.
THIS UNIT SHOULD BE ELECTRICALLY GROUNDED AND INSTALLED BY A LICENSED CONTRACTOR,
ELECTRICIAN, AND PLUMBER.
BUILDING MATERIALS AND WIRING SHOULD BE ROUTED AWAY FROM THE MOTOR/PUMP OR
BLOWER OR OTHER HEAT PRODUCING COMPONENTS OF THIS UNIT.
A PRESSURE WIRE CONNECTOR IS PROVIDED ON THE EXTERIOR OF THE MOTOR/PUMP AND
HEATER TO PERMIT CONNECTION OF AN NO. 8 AWG (8.4 MM) SOLID COPPER BONDING CONDUCTOR BETWEEN THIS UNIT AND ALL OTHER ELECTRIC EQUIPMENT AND EXPOSED METAL IN THE
VICINITY, AS NEEDED TO COMPLY WITH LOCAL REQUIREMENTS.
PRECAUTIONS
••
• Do not operate the hydromassage system unless the bath is filled with water to at least 1" to 2" (25,4 mm to 50,8 mm) above
••
the highest jet.
••
• Do not immerse the control panel by overfilling the bath.
••
••
• Do not use oil-based bath additives in your hydromassage bath.
••
••
• When cleaning your bath, do not use abrasive substances which will damage the bath's surface.
••
••
• To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).
••
••
• Do not use household cleansers on any of the wood surfaces if equipped.
••
NOTE: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. W e recommend
that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does
not cover improper installation related problems.
3
Jacuzzi Whirlpool Bath DE99000A 3/06
CONTENTS
Safety Instructions _____________________________________________________________________ 2-3
Contents _____________________________________________________________________________ 4
Specifications _________________________________________________________________________ 5-7
ENGLISH
Roughing-in Reference _________________________________________________________________ 8-11
Drop-in Installation _____________________________________________________________________ 12
Undermount Installation _________________________________________________________________ 13-14
Control Panel Installation_________________________________________________________________ 15
Service Access _______________________________________________________________________ 15
Electrical Connections___________________________________________________________________ 16
Plumbing and Water Supply ______________________________________________________________ 17
Clean-up After Installation _______________________________________________________________ 17
Wood Finish __________________________________________________________________________ 18
Operating Instructions __________________________________________________________________ 18-20
Maintenance Instructions ________________________________________________________________ 21-22
General Troubleshooting Guide ___________________________________________________________ 23
Authorized Service _____________________________________________________________________ 24
Warranty _____________________________________________________________________________ 25-26
NOTE: T o obt ain a referral for a service agent in your area call 800-288-4002. Y ou may also visit our web site at http:/
/www.jacuzzi.com/. To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
Jacuzzi Whirlpool Bath DE99000A 3/06
4
INSTRUCTIONS
DRAIN/OVERFLOW
B
A
B
A
UndermountWith Wood Frame
Important: Read complete instructions before beginning installation.
Each Fuzion whirlpool bath arrives completely equipped with motor/pump assembly , heater , and plumbing necessary for whirlpool operation. Before tub installation can begin, install overflow fitting and pull control panel cord
through control cutout in the tub deck. If unit is equiped with wood frame set frame aside in protective packaging until
final trim installation.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been
made. Do not lift the bath by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell and tub contents before installing. Should inspection reveal any damage or defect in the finish, do not install the bath. Damage or defect to the finish claimed after the bath is installed is
excluded from the warranty . Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the
products in good order to the carrier . Refer any claims for damage to the carrier. For definitions of warranty coverage
and limitations, refer to the published warranty information packed with the product or in the back of this manual.
All bath units are factory tested for proper operation and watertight connections prior to shipping. NOTE: Prior to
installation, the bath must be filled with water and operated to check for leaks that may have resulted from
shipping damage or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been
discovered, repaired, or avoided by following this inspection and testing procedure.
This manual is intended to assist you with the installation of your Fuzion tub.
Specifications for all tubs are combined.
Framing and Support installation instructions are divided into two sections;
drop-in and undermount.
The remaining instructions for all tubs are combined.
SPECIFICATIONS
ENGLISH
RECTANGULAR
SIDE VIEW
W
FUZION 7260 WITH WOOD FRAME SINGLE MOTOR
W
L
(Heater)
(Motor)
FUZION 7236 WITH WOOD FRAME
6-1/4" (159 mm)
H
6-1/4" (159 mm)
H
(Motor 1)
FUZION 7260 WITH WOOD FRAME DUAL MOTOR
(133 mm)
5-1/4"
(Motor)
W
H
END VIEW
L
(Heater)
SIDE VIEWEND VIEW
L
(Heater 1 & 2)
SIDE VIEWEND VIEW END VIEW
(Motor 2)
L
5" (127 mm)
(102 mm)
L
(Heater)
SIDE VIEW
W
FUZION 7260 UNDERMOUNT SINGLE MOTOR
W
(Motor)
FUZION 7236 UNDERMOUNT
5" (127 mm)
H
4"
(Motor 1)
W
H
END VIEW
L
(Heater)
SIDE VIEWEND VIEW
(Motor 2)
FUZION 7260 UNDERMOUNT DUAL MOTOR
H
(Heater 1 & 2)
(Motor 1)
SIDE VIEWEND VIEW END VIEW
5
Jacuzzi Whirlpool Bath DE99000A 3/06
ENGLISH
SPECIFICATIONS (Rectangular)
MODEL
FUZION 7236
WITH TEAK
LH RH
FUZION 7236
WITH WENGE
LH RH
FUZION 7236
UNDERMOUNT
LH RH
FUZION 7260
WITH TEAK
SINGLE MOTOR
LH RH
FUZION 7260
WITH WENGE
SINGLE MOTOR
LH RH
FUZION 7260
UNDERMOUNT
SINGLE MOTOR
LH RH
FUZION 7260*
WITH TEAK
DUAL MOTOR
FUZION 7260*
WITH WENGE
DUAL MOTOR
FUZION 7260*
UNDERMOUNT
DUAL MOTOR
70-11/16" (1795 mm) L
35-3/8" ( 899 mm) W
22-3/4" ( 578 mm) H
70-11/16" (1795 mm) L
35-3/8" ( 899 mm) W
22-3/4" ( 578 mm) H
70-11/16" (1795 mm) L
35-3/8" ( 899 mm) W
21-1/2" ( 546 mm) H
72" (1829 mm) L
60" (1524 mm) W
22-3/4" ( 578 mm) H
72" (1829 mm) L
60" (1524 mm) W
22-3/4" ( 578 mm) H
72" (1829 mm) L
60" (1524 mm) W
21-1/2" ( 546 mm) H
72" (1829 mm) L
60" (1524 mm) W
22-3/4" ( 578 mm) H
72" (1829 mm) L
60" (1524 mm) W
22-3/4" ( 578 mm) H
72" (1829 mm) L
60" (1524 mm) W
21-1/2" ( 546 mm) H
16-3/4" (425 mm) A
12" (305 mm) B
16-3/4" (425 mm) A
12" (305 mm) B
16-3/4" (425 mm) A
12" (305 mm) B
16-3/4" (425 mm) A
12-1/16" (306 mm) B
16-3/4" (425 mm) A
12-1/16" (306 mm) B
16-3/4" (425 mm) A
12-1/16" (306 mm) B
16-3/4" (425 mm) A
12-1/16" (306 mm) B
16-3/4" (425 mm) A
12-1/16" (306 mm) B
16-3/4" (425 mm) A
12-1/16" (306 mm) B
SPECIFICATIONS
TOTAL WEIGHT/
FLOOR LOADINGDIMENSIONS DRAIN/OVERFLOW CUTOUT HEATER
71" x 35"
(1803 mm x 889 mm)
71" x 35"
(1803 mm x 889 mm)
Template
Provided
P/N
DD42000
71" x 59"
(1803 mm x
1499 mm)
71" x 59"
(1803 mm x
1499 mm)
Template
Provided
P/N
DD44000
71" x 59"
(1803 mm x
1499 mm)
71" x 59"
(1803 mm x
1499 mm)
Template
Provided
P/N
DD44000
1238.8 lb
(563 kg)/
2
68.8 lb/ft
(335 kg/m2)
1238.8 lb
(563 kg)/
2
68.8 lb/ft
(335 kg/m2)
1188.8 lb
(540.4 kg)/
2
66 lb/ft
(321.4 kg/m2 )
1805 lb
(820.5 kg)/
2
60 lb/ft
(293 kg/m2 )
1805 lb
(820.5 kg)/
2
60 lb/ft
(293 kg/m2 )
1730 lb
(786 kg)/
57.6 lb/ft
(281 kg/m2 )
1849 lb
(840.5 kg)/
2
61.6 lb/ft
(300 kg/m2 )
1849 lb
(840.5 kg)/
61.6 lb/ft
(300 kg/m2 )
1774 lb
(806 kg)/
2
59.1 lb/ft
(288 kg/m2 )
Max - 101 U.S. gal
Max - 101 U.S. gal
Max - 101 U.S. gal
Min - 110 U.S. gal
Max - 148 U.S. gal
Min - 110 U.S. gal
Max - 148 U.S. gal
Min - 110 U.S. gal
2
Max - 148 U.S. gal
Min - 110 U.S. gal
Max - 148 U.S. gal
Min - 110 U.S. gal
2
Max - 148 U.S. gal
Min - 110 U.S. gal
Max - 148 U.S. gal
OPERATING
GALLONAGE
Min - 68 U.S. gal
(257 liters)
(382 liters)
Min - 68 U.S. gal
(257 liters)
(382 liters)
Min - 68 U.S. gal
(257 liters)
(382 liters)
(416 liters)
(560 liters)
(416 liters)
(560 liters)
(416 liters)
(560 liters)
(416 liters)
(560 liters)
(416 liters)
(560 liters)
(416 liters)
(560 liters)
PRODUCT
WEIGHT
195 lb
(88.6 kg)
195 lb
(88.6 kg)
154 lb
(70 kg)
274 lb
(125 kg)
274 lb
(125 kg)
199 lb
(90.5 kg)
319 lb
(145 kg)
319 lb
(145 kg)
244 lb
(111 kg)
Factory Installed
(S749000 Heater)
Factory Installed
(S749000 Heater)
Factory Installed
(S749000 Heater)
Factory Installed
(S749000 Heater)
Factory Installed
(S749000 Heater)
Factory Installed
(S749000 Heater)
Factory Installed
(BN60000 Heater)
Factory Installed
(BN60000 Heater)
Factory Installed
(BN60000 Heater)
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
SINGLE MOTOR units:
RapidHeatTM: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 120 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
*DUAL MOTOR units: (2) Two 230 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuits required.
One (1) Heater and (1) Motor/Pump on each 230 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Jacuzzi Whirlpool Bath DE99000A 3/06
6
CORNER BATHS
SPECIFICATIONS
(159 mm)
L
6-1/4"
H
(Motor)
SIDE VIEW END VIEW
FUZION 6666 WITH WOOD FRAME
(127 mm)
L
5"
H
SIDE VIEW END VIEW
(Motor)
FUZION 6666 UNDERMOUNT
SPECIFICATIONS (Corner)
MODEL
FUZION 6666
WITH TEAK
LH RH
FUZION 6666
WITH WENGE
LH RH
FUZION 6666
UNDERMOUNT
LH RH
66" (1676 mm) L
66" (1676 mm) W
22-3/4" ( 578 mm) H
66" (1676 mm) L
66" (1676 mm) W
22-3/4" ( 578 mm) H
66" (1676 mm) L
66" (1676 mm) W
21-1/2" ( 546 mm) H
16-13/16" (427 mm) A
12-1/8" (308 mm) B
16-13/16" (427 mm) A
12-1/8" (308 mm) B
16-13/16" (427 mm) A
12-1/8" (308 mm) B
W
A
A
ENGLISH
(Heater)
B
DRAIN/OVERFLOW
B
UndermountWith Wood Frame
W
(Heater)
PRODUCT
WEIGHT
256 lb
(116.4 kg)
256 lb
(116.4 kg)
184 lb
(83.5 kg)
Factory Installed
(S749000 Heater)
Factory Installed
(S749000 Heater)
Factory Installed
(S749000 Heater)
See
Page 11
See
Page 11
Template
Provided
P/N
DD43000
Min - 124 U.S. gal
2
Max - 176 U.S. gal
Min - 124 U.S. gal
2
Max - 176 U.S. gal
Min - 124 U.S. gal
2
Max - 176 U.S. gal
OPERATING
GALLONAGE
(469 liters)
(666 liters)
(469 liters)
(666 liters)
(469 liters)
(666 liters)
TOTAL WEIGHT/
FLOOR LOADINGDIMENSIONS DRAIN/OVERFLOW CUTOUT HEATER
1923 lb
(874 kg)/
72.6 lb/ft
(354 kg/m2)
1923 lb
(874 kg)/
72.6 lb/ft
(354 kg/m2)
1851 lb
(841 kg)/
69.8 lb/ft
(340 kg/m2)
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
RapidHeatTM: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 120 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
7
Jacuzzi Whirlpool Bath DE99000A 3/06
70-11/16''
Motor
12" H x 18" L
Service Access
Opt. Service Access
35-3/8''
17-11/16''
2''
7''
10-1/4''
12'' x 4"*
Heater (S)
FUZION 7236 RIGHT HAND WITH WOOD FRAME
s
Motor
12" H x 18" L
Service Access
Opt. Service Access
17-11/16''
2''
7''
10-1/4''
12'' x 4"*
Heater (S)
70-11/16''
35-3/8''
FUZION 7236 RIGHT HAND UNDERMOUNT
ROUGHING-IN REFERENCE (RECTANGULAR)
ROUGHING-IN REFERENCE
NOTE: Some of these units have been provided with cutout templates included in shipping carton.
See CUTOUT information for each model on page 6-7.
70-11/16''
ENGLISH
17-11/16''
12'' x 4"*
Motor
Heater (S)
35-3/8''
7''
10-1/4''
2''
Opt. Service Access
12" H x 18" L
Service Access
70-11/16''
17-11/16''
10-1/4''
12'' x 4"*
7''
2''
Heater (S)
Motor
Opt. Service Access
35-3/8''
12" H x 18" L
Service Acces
FUZION 7236 LEFT HAND UNDERMOUNT
NOTE: 1. Unless otherwise specified, units are produced with left or right-hand versions.
2. Service Access dimensions given are minimum size.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. THE OVERALL DIMENSIONS ARE NOMINAL WITH A TOLERANCE OF +0 AND -1/4" (6,4 mm).
Jacuzzi Whirlpool Bath DE99000A 3/06
8
ROUGHING-IN REFERENCE
s
s
ROUGHING-IN REFERENCE (RECTANGULAR)
NOTE: Some of these units have been provided with cutout templates included in shipping carton.
See CUTOUT information for each model on page 6-7.
72"
Motor
12" H x 18" L
Service Access
Heater (S)
60"
Motor
ENGLISH
72"
60"
18-1/2" x 4"
8.47"
12"
24.19"
36"
FUZION 7260 SINGLE MOTOR WITH WOOD FRAME
LEFT HAND MOTOR
72"
Motor
12" H x 18" L
Service Access
Heater (S)
18-1/2" x 4"
8.47"
12"
24.19"
36"
FUZION 7260 SINGLE MOTOR UNDERMOUNT
LEFT HAND MOTOR
60"
18-1/2" x 4"
Heater (S)
8.47"
12"
24.19"
Optional
Service Access
36"
FUZION 7260 SINGLE MOTOR WITH WOOD FRAME
RIGHT HAND MOTOR
72"
Motor
Heater (S)
18-1/2" x 4"
8.47"
12"
24.19"
Optional
Service Access
36"
FUZION 7260 SINGLE MOTOR UNDERMOUNT
RIGHT HAND MOTOR
12" H x 18" L
Service Acces
60"
12" H x 18" L
Service Acces
NOTE: 1. Unless otherwise specified, units are produced with left or right-hand versions.
2. Service Access dimensions given are minimum size.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. THE OVERALL DIMENSIONS ARE NOMINAL WITH A TOLERANCE OF +0 AND -1/4" (6,4 mm).
9
Jacuzzi Whirlpool Bath DE99000A 3/06
ROUGHING-IN REFERENCE
s
ROUGHING-IN REFERENCE (RECTANGULAR)
NOTE: Some of these units have been provided with cutout templates included in shipping carton.
See CUTOUT information for each model on page 6-7.
Optional Service Access
72"
ENGLISH
Heater (S)
Motor
Heater (S)
Optional
Service Access
60"
12" H x 18" L
Service Access
12" H x 18" L
8.47"
12"
12"
12" H x 18" L
Service Access
8.47"
Motor
18-1/2" x 4"
24.19"
36"
FUZION 7260 DUAL MOTOR WITH WOOD FRAME
NOTE: 1. Unless otherwise specified, units are produced with left or right-hand versions.
2. Service Access dimensions given are minimum size.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. THE OVERALL DIMENSIONS ARE NOMINAL WITH A TOLERANCE OF +0 AND -1/4" (6,4 mm).
Heater (S)
Motor
Heater (S)
Optional
Service Access
72"
Optional Service Access
Motor
Service Access
18-1/2" x 4"
24.19"
36"
FUZION 7260 DUAL MOTOR UNDERMOUNT
60"
12" H x 18" L
Service Acces
Jacuzzi Whirlpool Bath DE99000A 3/06
10
ROUGHING-IN REFERENCE
Motor
12" H x 18" L
Service Access
Heater (S)
46.61"
66"
20" X 4"
32.97"
Ref.
66"
37.23"
9.29"
32.97"
40.94"
40.94"
69.68"
FUZION 6666 CORNER UNDERMOUNT
RIGHT HAND MOTOR
ROUGHING-IN REFERENCE (CORNER)
NOTE: Some of these units have been provided with cutout templates included in shipping carton.
See CUTOUT information for each model on page 6-7.
ENGLISH
40.94"
40.94"
69.68"
Ref.
66"
20" X 4"
Motor
32.97"
12" H x 18" L
Service Access
Heater (S)
46.61"
FUZION 6666 CORNER WITH WOOD FRAME
LEFT HAND MOTOR
69.68"
Ref.
Motor
32.97"
12" H x 18" L
Service Access
40.94"
66"
20" X 4"
Heater (S)
46.61"
40.94"
66"
66"
9.29"
32.97"
32.97"
37.23"
9.29"
37.23"
40.94"
40.94"
69.68"
Ref.
66"
20" X 4"
32.97"
Heater (S)
46.61"
FUZION 6666 CORNER WITH WOOD FRAME
RIGHT HAND MOTOR
66"
Motor
32.97"
9.29"
37.23"
12" H x 18" L
Service Access
FUZION 6666 CORNER UNDERMOUNT
LEFT HAND MOTOR
NOTE: 1. Unless otherwise specified, units are produced with left or right-hand versions.
2. Service Access dimensions given are minimum size.
3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
5. THE OVERALL DIMENSIONS ARE NOMINAL WITH A TOLERANCE OF +0 AND -1/4" (6,4 mm).
CORNER CUTOUT
NOTE: Use this cutout for tubs with wood frame ONLY. Undermount
tubs come with a cutout template.
11
67-1/2"
Ref.
65"
65"
DRAIN
32"
32"
48"
FUZION 6666 CORNER CUTOUT
Jacuzzi Whirlpool Bath DE99000A 3/06
DROP-IN TUB INSTALLA TION INSTRUCTIONS
Use these Framing and Support instructions for Fuzion tubs with wood frame.
Framing and Support
The drain/overflow must be installed before beginning this step. See Plumbing and Water Supply for details and
instructions. The drain/overflow tailpiece of the bath extends below the bottom of the bath. Note that this requires a
ENGLISH
cutout in the floor.
The floor structure beneath the bath must be able to support a total weight of bath, water, and bather.
Refer to the table in SPECIFICA TIONS under Total Weight for your model. The unit must be supported from the
bottom of the bath and not from the bath rim. If the subfloor is level and a continuous surface, no other preparation
is necessary . You can proceed to install the bath. If the subfloor is not level, you MUST level the entire surface prior
to installing the bath. The use of materials that shim or provide a level installation are allowed provided the method
used will insure a level bath that is supported from the bottom. Materials that may be used are a floor leveling
compound, mortar , plaster or minimal exp ansion structural foam having a density of a minimum of 5 lbs./cubic feet;
however the bath must remain level in order for it to drain properly and all foam feet must make full contact with the
leveling material. Both sides of a joint or splice of subfloor should be level to each other.
NOTE: Drop-In Bath units are equipped with metal anchor straps. These straps can be used to secure the
unit to the floor or sub-floor to reduce movement after inst allation. If mortar or similar anchoring material is
used, these straps are not necessary.
WARNING: ALL foam feet must cont act the floor . Anchoring strap s and/or other anchoring materials will not
properly anchor unit if ALL foam feet are NOT in contact with a level floor. Operating a unit improperly
installed may cause irreparable damage to the unit.
The rim of the bath is not designed to support weight. If finish material is to overlap or contact the bath, the added
weight must be fully self-supporting.
The wood frame must be attached before beginning these instructions. The drain overflow parts must be as-
sembled and properly installed.
The protective film liner inside the bath is used to prevent damage to the finish during installation. Before
installation, remove liner to inspect for any defects, reapply and do not remove until final cleanup.
Install optional trim parts when all installation has been completed.
TYPICAL INSTALLATION
MORTAR OR
ADHESIVE
TILE
CEMENT
BOARD
SUB-FLOOR
SEALANT
FLASHING
SEMI-SUNKEN
1" X 4" (NOT FOR SUPPORT)
ANCHOR
STRAP
NAIL OR SCREW
THROUGH
ANCHOR STRAP
INTO FLOOR
FLOOR
Jacuzzi Whirlpool Bath DE99000A 3/06
12
UNDERMOUNT TUB INSTALLA TION INSTRUCTIONS
T
Use these Framing and Support instructions for Fuzion undermount tubs.
UNDERMOUNT INSTALLATION OPTIONS
The undermount gives the opportunity to be flexible in the design and location of the bath. Examples are shown for
possible installations.
CORNER NICHE
Installation
A typical installation will have these construction characteristics.
Unit Protection
If protective film has been removed, reapply film. For added protection, place a drop cloth or other material in the
bottom of bath for protection. Be careful not to scratch the bath surface.
FREE STANDING
COUNTER
MORTAR*
*MORTAR MUST BE IN CONTACT WITH ALL FOAM FEE
ENGLISH
Counter Preparation
Locate the tub in the position for the installation. The
drain overflow parts MUST be assembled and properly
installed. See Plumbing and Water Supply.
Position the template so that the cutout aligns with the
tub's rim edge.
With bath and template in this position, using a grease
pencil, mark on the bath the center line positions through
the cut out. Remove template. Measure from marked
center lines to a fixed point such as a wall.
B
A
TEMPLATE
COUNTER
C
D
TEMPLATE
ALIGN
BATH RIM
B
A
D
MEASURE FROM
CENTERLINE
MARKS TO WALL
STUD WALL
C
Transfer these measurements to counter and mark
center lines positions. Position template and cut
counter for the desired offset including control panel
cutout.
After cutting is complete, perform any needed
routing, edge work or polishing to the counter.
13
Jacuzzi Whirlpool Bath DE99000A 3/06
COUNTER
BATH
Control Panel
cord
COUNTER
BATH
COUNTER
BATH
WEIGHTS
UNDERMOUNT TUB INSTALLA TION INSTRUCTIONS
Position the counter on top of the bath to ensure
correct fit and appearance. Make any adjustments that
may be necessary. Remove the counter.
ENGLISH
Adhering Counter to Bath
Ensure control panel cord (from underneath) is routed
up through the control panel cutout in the counter and
secured before gluing counter to tub.
Clean any dirt or debris from the bath rim. Do not use
abrasive cleaners.
Where the counter will make contact with top of the
bath rim, apply a bead of silicone sealant (not provided).
CAUTION: Do not use an adhesive or adhesive
sealant to secure the counter to the bath rim. If
maintenance or remodelling is required the counter
may have to be removed. Adhesive will permanently
bond the counter to the bath. This will make removal
difficult and costly and may cause damage to the
counter or bath.
Carefully position the counter onto the bath rim. The
counter will need to be held in place while the sealant
cures. Follow the manufacturer's instructions to determine time required for curing.
Apply a continuous bead of silicone sealant around
the entire seam between the counter and bath rim. Allow
sealant to skin over or cure before cleaning the counter
or bath.
COUNTER
APPLY
SILICONE
BATH RIM
HERE
Jacuzzi Whirlpool Bath DE99000A 3/06
14
SERVICE ACCESS
INST ALLA TION INSTRUCTIONS
Control Panel Installation
For drop-in and undermount installations, install the control panel as shown below.
The control panel cutout opening in the assembled wood frame and tub and in the assembled counter and tub
must be clear and free of adhesive.
Control panel and wire to be free of defects. Insert wire into panel connector.
ENGLISH
Apply adhesive sparingly around base of control panel.
Apply sparingly to
avoid squeeze out
Adhesive
Connect Blower
wire here
(Grey wire)
Connect Control Box
wire here
(Black wire)
Thread wire through cutout and to control box. Orientate control panel so that the Jacuzzi logo is read from the inside
of the tub. Lower control panel in cutout and press firmly to embed adhesive.
Connect wire to control box.
Inside of tub
Inside of tub
Service Access
For partially or fully sunken installations, allow for access to service connections. It is the installer's responsibility to provide sufficient service access. The recommended minimum dimensions allowable for service to
the bath are shown in the "Service Access" illustration.
The recommended location(s) of the service access are
shown on the Rough-in drawings.
Provide adequate area around unit for air circulation
for cooling the motor and to supply sufficient air to the
jets. Do not insulate this area or around motor.
In some cases, access may not have been provided
because of the design of the bath environment and having full understanding that in this case, it may be necessary to remove the unit for service.
If this is the case, diagnosing a problem may not be
possible without complete access to the plumbing system. This would necessitate the removal of the unit.
Although this practice is not commonly implemented, it
is an acceptable method.
SERVICE ACCESS
FRONT
ALTERNATE
ACCESS
(WITHOUT SKIRT)
HEATER
12"
18"
MOTOR
12"
18"
PREFERRED
ACCESS
AREA
AREA
B
MOTOR
A
In some cases access may have been provided in
Area A but service is required in Area B which requires
the unit to be pulled for service and reinstalled.
If service access has not been provided, it is the
home owners responsibility to remove the bath and
provide the required access, should a repair become
necessary.
15
Jacuzzi Whirlpool Bath DE99000A 3/06
INST ALLA TION INSTRUCTIONS
Electrical Connections
Separate circuits for all (except the Fuzion 7260 Dual motor) tubs, each must be protected by a Ground Fault
Circuit Interrupter (GFCI), are required for the pump/motor and the RapidHeatTM Heater. The Fuzion 7260 Dual motor
tubs require two (2) separate circuits, each must be protected by a Ground Fault Circuit Interrupter (GFCI), for each
pump/motor and RapidHeatTM Heater combination.
ENGLISH
Refer to the electrical specification for each model on pages 6 - 7. Install duplex outlets to the studwall underneath
the bathtub, at least 4 inches (10,2 cm) above the floor or in accordance with local building or electrical codes. Duplex
outlets are not provided. Because these units are manufactured with an electronic control panel no remote switch or
timer is necessary .
Tubs with electronic control panels combine the electrical requirements of the pump/motor and electronic controls
into a control box. For these units the power supply cord from the pump/motor runs to the control box. The power
supply cord from the control box should be connected to the correctly rated amperage GFCI circuit.
Before installing electrical connections, inspect the pump/motor and heater nameplates and confirm you have 120
V AC, 20 AMP and 15 AMP or 230 VAC, 20 AMP service requirements. The GFCI circuit s must match these requirements. Care must be taken:
FOR 120 V AC unit s
Connect the 120 V AC, 20 AMP pump/motor or control box power cord ONLY to the 120 VAC, 20 AMP GFCI circuit
Connect the 120 V AC, 15 AMP heater power cord ONLY to the 120 VAC, 15 AMP GFCI circuit.
FOR 230 V AC unit s
Connect one 230 VAC, 20 AMP control box power cord controlling one pump/motor and heater set ONLY to one
230 V AC, 20 AMP GFCI circuit.
Connect the second 230 VAC, 20 AMP control box power cord controlling the other pump/motor and heater set
ONL Y to the other 230 VAC, 20 AMP GFCI circuit.
Do NOT switch power cords and GFCI circuits.
With a #8 solid copper wire (not provided), bond the heater to the house electrical panel or approved local bond. A
bonding lug is provided on the heater. With another #8 solid copper wire (not provided), bond the pump/motor to the
house electrical panel or approved local bond. A bonding lug is provided on the pump/motor.
At initial start-up and before each use thereafter with power ON, push the GFCI test button on each circuit. The
reset button should pop out. Push this button in to reset. If the interrupter fails to operate in this manner, there is a
ground current flowing or a device malfunction, indicating the possibility of electrical shock. Turn OFF power and do
not use the bath until the source of the problem has been identified and corrected.
DANGER: RISK OF ELECTRIC SHOCK. Connect only to a circuit protected by a Ground Fault Circuit Interrupter (GFCI).
CAUTION: Operating the motor/pump without enough water in the bath can cause leaking and permanent
damage to the pump. Before power is applied to the installation, make sure the switch is in the OFF position
to avoid pump damage.
ELECTRICAL CONNECTION 120 VAC ONLY
15 AMP, 3 PRONG PLUG
(Heater)
20 AMP, 3 PRONG PLUG
(Pump/Motor)
M
T
HEATER
* INSTALL SEPERATE
GFCI PROTECTED CIRCUITS,
DUPLEX RECEPTS NOT PROVIDED
DUPLEX
RECEPT.*
4" MIN.
OR IN
ACCORDANCE
WITH LOCAL
BUILDING OR
ELECTRICAL
CODES
ELECTRICAL CONNECTION - HEATER AND PUMP/MOTOR 230V
230V GFCI
PROTECTED
CIRCUIT*
4" MIN.
OR IN
ACCORDANCE
WITH LOCAL
BUILDING OR
ELECTRICAL
M
T
HEATER
SUPPLIED POWER CORD
FROM JUNCTION BOX TO
GFCI PROTECTED
CIRCUIT
CODES
*(NOT PROVIDED)
16
Jacuzzi Whirlpool Bath DE99000A 3/06
Plumbing and Water Supply
Plumbing
All Jacuzzi Whirlpool Bath products are factory tested for
proper operation and watertight connections prior to shipping.
If leaks are detected, notify your Jacuzzi Whirlpool Bath dealer.
Do not install the unit.
Water Supply
Consult local authorities for plumbing code requirements
in your area.
IMPORTANT: Proper installation of the fill spout plumbing and compliance with local codes are the responsibility of the installer . Jacuzzi Whirlpool Bath does not warrant connections of water supply fittings and piping, fill
systems, or drain/overflow systems. Nor is it responsible
for damage to the bath which occurs during installation.
CAUTION: A nonflammable protective barrier must be
placed between soldering work and bath unit to prevent
damage to the bath.
Faucet Installation
NOTE: Selecting a faucet for rim mounting:
The combined thickness at the rim of the tub shell and the
wood trim is 2" (50,8 mm) nominal. The length of the
faucet tailpiece(s) must be long enough to extend past
this dimension and have ample clearance to assemble any
hardware (i.e. locknut, water supply fittings, etc.) necessary for installation. For undermount units, the combined
thickness of the tub shell is 1/2" (12, 7 mm) nominal and
the undermount deck should not exceed the length of the
faucet tailpiece(s) including any assembly hardware.
Drain Overflow (supplied)
A drain/overflow assembly must be installed on the bath,
water tested, and connected to the sanitary system of the house.
After opening the carton, inspect for damage or missing parts.
NOTE: The overflow fitting (supplied) of the drain/overflow assembly MUST be installed before the wood frame
or (for undermount tubs) the counter is installed.
Overflow Fitting Installation
Remove and open the overflow fitting from the drain kit
(supplied). Remove washers and nuts from the overflow fitting.
Place a small bead of plumbers putty, silicone, or similar
approved sealant around the underside of the top flange.
Place the overflow fitting into the overflow hole of the tub.
From the underside of the unit, place the rubber washer
then locknut on the fitting and tighten securely. Be careful
not to over tighten.
The overflow fitting accepts 1-1/2" (38 mm) slip joint type
drain line connections. Assemble in accordance with local
plumbing or building codes.
After the drain is fully installed, test for proper drainage. If
the unit does not drain properly, rectify this condition before
proceeding with the installation. Jacuzzi Whirlpool Bath is
not responsible for removal and or reinstallation costs.
NOTE: Watertight installation of the drain is the inst aller's
responsibility. Drain leakage is excluded from the Jacuzzi
Whirlpool Bath warranty of this product.
OVERFLOW
FITTING
ENGLISH
Anti-Siphon Valve or Equivalent Backflow
Preventer
Optional backflow prevention installation. Anti-Siphon
valves or Equivalent Backflow Preventers are not supplied
with the tub. Consult your local plumbing code requirements
for the minimum height above the tub rim.
FLAT RUBBER WASHER
LOCKNUT
SLIP JOINT WASHER/NUT
Clean-Up After Installation
Acrylic Surfaces
To avoid dulling and scratching the acrylic surface of the bath, never use abrasive cleaners. A mild liquid detergent and warm
water will clean soiled surfaces.
Remove spilled plaster with a wood or plastic edge. Metal tools will scratch the surface. S pot s lef t by plaster or grout can be
removed if lightly rubbed with detergent on a damp cloth or sponge.
CAUTION: Use of chemicals and/or chemical cleaners may be hazardous to your health.
Paint, tar , or other dif ficult surface stains can be removed with p aint thinner, turpentine, or isopropyl alcohol (rubbing alcohol).
NOTE: use these chemicals only on ACRYLIC SURFACE stains.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper.
You can restore the glossy finish to the acrylic surface of the bath with a special compound, Meguiar's #10 Mirror Glaze. If that
is not available, use automotive rubbing compound followed by an application of automotive paste wax.
Major scratches and gouges which penetrate the acrylic surface will require refinishing. Ask your Jacuzzi Whirlpool Bath
dealer for special instructions or visit our web site at http://www.jacuzzi.com/. To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
Wood Surfaces
Cleaning
Your teak/wenge wood is dissolved by strong or corrosive cleaners, so always use the mildest cleaner. NOTE: DO NOT
USE HARSH CLEANERS ON WOOD SURFACES.
CAUTION: Use of chemicals and/or chemical cleaners may be hazardous to your health.
A 75/25 mixture of liquid laundry detergent and chlorine bleach may be adequate. Apply this mixture with a stiff brush,
scrubbing lightly with the grain. Leave it on the wood for several minutes to give the detergent time to suspend the dirt and
the bleach time to lighten the wood, then rinse the wood thoroughly, brushing it to clear the grain. Allow to dry.
PUTTY/SEALANT
(NOT PROVIDED)
TIGHT
LOOSE
17
Jacuzzi Whirlpool Bath DE99000A 3/06
WOOD FINISH
Finishes
Wood frames are factory finished with a clear satin spar varnish. Periodic maintenance for the spar varnish is required.
Clean wood frame with mild household detergent. NOTE: Do not use harsh chemicals or cleaners.
CAUTION: Use of chemicals and/or chemical cleaners may be hazardous to your health.
ENGLISH
Repairs to damaged finish should be made by a qualified wood refinisher, contact a professional furniture refinisher.
OPERATING INSTRUCTIONS
OPERATION
NOTE: These instructions pertain to all bath products manufactured by Jacuzzi Whirlpool Bath. Not all features discussed in this instruction pamphlet apply to all baths.
All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained
after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold
water continuously like pools or spas. If you want a unit designed to continuously hold water, see your Jacuzzi Whirlpool Bath
dealer for the complete line of whirlpool spas available.
Once the bath is installed, remove any residue or foreign materials left over from construction. Paint, tar , or other difficult surface
stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol). NOTE: Use these chemicals only on
SURFACE stains. Other dirt can be cleaned off with a mild liquid detergent on a damp cloth. Scrape off plaster with a wooden or
plastic edge; do not use metal scrapers, wire brushes or other metal tools, as they will damage the bath's surface.
Water Level
Close the drain and fill the bath until water is at least 1" to
2" (2,5 - 5,08 cm) above the highest jet (see water line indicated in the illustration). Do not turn on the whirlpool sys-
tem at any time if the jets are not completely immersed in
water. Do not immerse the control panel by overfilling
the bath. Running the whirlpool system when there is insuf-
ficient water in the bath could result in water spraying outside
the bath area. Running the whirlpool system without water
will damage the recirculating pump.
IMPORTANT: When exiting the bath, the water level will drop
below the jets which could result in water being sprayed out
of the unit. To prevent this, you must turn unit off before
exiting bath.
FILL TO AT LEAST
1" - 2" ABOVE HIGHEST JET
1" - 2"
Controlling Whirlpool Action
The whirlpool action in your bath is influenced by three
factors – direction of flow, force of water, and force of air. All
baths manufactured by Jacuzzi Whirlpool Bath are equipped
with fully adjustable PowerPro® jets, which are adjustable for
all three factors. Some baths have additional directionally
adjustable jets which can be adjusted for direction and flow of
air only.
Direction: T o change the direction of the water flow , swivel
the jet nozzle to the desired angle. The jets can be directed
individually toward any location on your body to provide a
hydromassage. The jets can also be adjusted so that they all
point in the same direction (clockwise or counterclockwise)
to circulate the water in a circular motion around the bath,
causing a total whirlpool effect.
Water Force: The high volume, fully adjustable jets can
be adjusted to control the force of the water coming into the
bath. For robust action, increase the force of the flow by rotating the jet handles to the left (counterclockwise). For a
more gentle effect, rotate the handles to the right (clockwise).
Customize water force by lowering water volume of one (1)
jet(s) to increase water force in another jet(s). Never run the
whirlpool system with all the jets closed.
Force of Air: The intensity of the hydromassage whirl-
pool action is determined by the amount of air inducted into
the water. As the amount of air is increased, the hydromassage action increases. For maximum air induction, increase
the amount of air using the Air Flow Increase buttons on the
control panel. For fewer air bubbles, decrease the amount of
air using the Air Flow Decrease buttons on the control panel.
When the knobs are turned to the smallest circles, only water
is being circulated.
Jacuzzi Whirlpool Bath DE99000A 3/06
18
OPERATING INSTRUCTIONS (cont'd)
Electronic Control Panel Operation (with optional Chromotherapy/Illumatherapy
All tubs in this product line come with electronic controls and standard Chromotherapy or IllumatherapyTM. Read and follow
the operation instructions for the control system of your unit.
General Functions
This Jacuzzi tub is equipped with a seven button electronic control panel. The seven button panel controls a two speed pump/
motor, Chromotherapy or IllumatherapyTM lighting, air controls, and wave control. LED lights (in the control panel) indicate function
levels. When switching between functions, the LED for the inactive functions will dim and the active function will brighten.
The bath is equipped with a water level sensor(s). When the water level is below the sensor, the pump/motor can not be
activated. If the ON/OFF pump/motor button is pressed at this time, the pump/motor will not operate. When the water goes
above the water level sensor, the pump/motor can be activated. If the water level drops below the level sensor, the pump/motor
will shut OFF. To restart the pump/motor after the water level goes above the level sensor, the ON/OFF pump/motor button must
be pressed. The pump/motor will automatically shut off 30 minutes after the pump/motor was turned on.
NOTE: Ensure the water level sensor located inside the bath is free of any soap or dirt buildup.
TM
lighting)
ENGLISH
Normal Operation (with the bath filled to the proper level)
Pump/Motor Switch (ON/OFF )
Pressing the button will turn ON the two speed pump/
motor at HIGH speed. Pressing a second time will turn OFF
the pump/motor. To change speeds use the Toggle buttons.
Pump/Motor Status LED
When the pump/motor is ON at HIGH speed all four LED
indicator lights will be lit. When the pump/motor is ON at
LOW speed the bottom LED indicator light will be lit.
Left Air Valve Switch
Pressing this button will acitvate the left air valves use
the Toggle buttons to increase/decrease air flow to the left set
of jets. The air flow can be adjusted from no air to maximum
air.
Left Air Valve Status LED
The Left Air Valve Status LED will show four LED lights at
maximum air and only one LED light when the air is turned
OFF. Each additional LED indicates more air flow.
Right Air Valve Switch
Pressing this button will acitvate the right air valves. Use
the Toggle buttons to increase/decrease air flow to the right
set of jets. The air flow can be adjusted from no air to maximum air.
Right Air Valve Status LED
The Right Air Valve Status LED will show four LED lights at
maximum air and only one LED light when the air is turned
OFF. Each additional LED indicates more air flow.
Bath Light Switch (ON/OFF )
Pressing this button will turn ON the white bath light(s).
Pressing the Toggle buttons at this time will increase or decrease light intensity. Pressing the button a second time will
access the saved favorite color. To cycle lighting colors use
the Toggle button. Pressing the Toggle button again will stop
the light cycling. The color displayed when the cycle has been
stopped will be saved as your favorite color. Pressing the
button a third time to turn OFF the light.
NOTE: When switching between functions, the LED for
the inactive functions will dim and the active function will
brighten.
Bath Light
Wave Function
Right Air Valve
Toggle Switches
Right Air Valve
Status LED
Left Air Valve
Status LED
Pump/Motor
Status LED
Left Air Valve
ON/OFF
Pump/Motor
Wave Function Switch (ON/OFF )
Pressing this button activates wave action by opening
and closing both right and left air valves. Pressing a second
time will turn OFF the wave action.
T oggle Buttons
The T oggle buttons, up and down , act on each of the
other buttons to increase, decrease, or modify functionality.
Use the up arrow to increase and the down arrow to decrease.
• Pressing a toggle button after pressing the Pump/Motor
button will increase or decrease speeds on the Pump/Motor. If the pump/motor is on HIGH speed press the down
arrow to select LOW speed. If the pump/motor is on LOW
speed press the up arrow to select HIGH speed.
• Pressing an up or down toggle button after pressing the
Bath Light button once will increase or decrease the white
light brightness. Pressing an up or down toggle button
after pressing the Bath Light button twice will begin cycling
the light colors. Leave the colors cycling or press the same
toggle button again to stop the color cycling. With the lights
stopped on a color pressing the Bath Light button a third
time will turn OFF the light. (A favorite color will be saved
ONLY when the cycling has been stopped on that color
and then turned OFF.)
19
Jacuzzi Whirlpool Bath DE99000A 3/06
PUSH TO RESET
OVER HEAT
PROTECTION
HIGH LIMIT RESET
HEATER ON
HEATER ON
OPERATING INSTRUCTIONS (cont'd)
RapidHeat
TM
Operation
Once the heater is installed and the whirlpool pump is operating, the heating
function is totally automatic. The heater will help maintain the temperature of the
ENGLISH
water in the bath.
Vacuum/Pressure Switch
The heater is equipped with a preset vacuum/pressure switch which will not allow the heater to turn ON if the pump is not running with water flowing through the
whirlpool system.
High-Limit Switch
The heater includes an exclusive High-Limit switch. This safety circuit will not false trip from hot tap water. It will only turn of f
the heater if the thermostat fails. To reset, press the button. If the high-limit trips frequently, contact your Authorized Electrical/
Mechanical Service Provider. Visit our web site at http://www.jacuzzi.com/.
To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
Jacuzzi Whirlpool Bath DE99000A 3/06
20
E
MAINTENANCE INSTRUCTIONS
Cleaning the Bath
To clean your bath, simply use a mild, nonabrasive liquid
detergent solution on the acrylic surfaces. To clean the wood
surfaces, follow the wood finish manufacturer's maintenance
and cleaning instructions.
You can protect and restore the gloss to a dulled acrylic
surface by applying Meguiar's #10 Mirror Glaze, a product
specifically designed for use on acrylic finishes. If Meguiar's
is not available, an acrylic polish of equal quality or automotive paste wax is acceptable.
Never use abrasive household cleaners on any Jacuzzi
Whirlpool Bath product.
Repairs to the Surface
Minor scratches which do not penetrate the acrylic color
finish can be removed by lightly sanding with 600-grit wet/dry
sandpaper. Restore the gloss using Meguiar's Mirror Glaze
or automotive paste wax.
Major scratches and gouges which penetrate the acrylic
surface will require refinishing. Ask your Jacuzzi Whirlpool
Bath dealer for special instructions.
Minor scratches which do not penetrate the wood finish
can be repaired using the manufacturer's recommendations.
Major scratches and gouges which penetrate the wood
surface will require refinishing.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED
AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the whirlpool system, it is recommended that a whirlpool bath be
purged at least twice a month. For best results, however, we
recommend that you purge your whirlpool bath after each use
using our exclusive two-part plumbing system cleaner made
specifically for whirlpool baths. Systems Clean™ is available
through an authorized Jacuzzi Whirlpool Bath Distributor or by
calling us direct at 1-800-288-4002. Instructions for use:
Immediately after bathing and exiting the whirlpool bath, leave
the bath water in the tub and add hot water, if necessary, so the
water is at least 1" to 2" (25,4 mm to 50,8 mm) above the
highest jet. Turn on the unit without the aerator. Pour the
contents of the Systems Clean Packet 1 (taking care not to get
the material on yourself) into the bath near the intake for the
circulation pump. Repeat same process with Systems Clean
Packet 2. It is important to use Packet 1 before Packet 2
to avoid a strong odor. Run the bath for 5 to 10 minutes.
Drain completely and rinse any residue.
If you have followed the standard purging instructions
above and still have an excess accumulation of bath residue
and desire an alternative cleaning mechanism, we recommend SUPER SYSTEMS CLEAN PLUS manufactured by
Stearns Packaging to rectify this condition. This may be
obtained by contacting us at l-800-288-4002. It is recommended that you follow the instructions provided by the
manufacturer with the product. Repeated use may be necessary. SUPER SYSTEMS CLEAN PLUS does not replace the
necessity to regularly purge your whirlpool system with Systems Clean as recommended.
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.
If you want to use any kind of bath additive, use only a small
amount of low-foaming powder or crystal substance; the
whirlpool action intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath additives may increase the level of accumulations of bath residue
in the whirlpool system. If excess accumulations persist, you
should discontinue use of these products.
Spinning Jets Maintenance
(Models equipped with spinning jets)
If hair or other kind of debris gets caught in the bearings of
these jets, it could cause them to stop spinning. This may
require disassembly and cleaning. To do this, simply grab the
nozzle and pull straight out of the jet housing. The bearing
casing will be attached to the nozzle. These can be separated
by holding the casing and pushing the nozzle out from the rear
of the casing. After cleaning, reassemble in reverse.
PUSH FROM REAR
TO REMOVE
NOZZLE
NOZZL
BEARING CASING
ENGLISH
21
Jacuzzi Whirlpool Bath DE99000A 3/06
NOTCH
GASKET
COVER STRAINER
SCREW
SUCTION
FITTING
SUCTION COVER/STRAINER ASSEMBLY
MAINTENANCE INSTRUCTIONS
Suction Cover/Strainer Maintenance
Clean the suction cover/strainer of hair and debris when
necessary. To do this, remove the center screw and detach
the square cover. Clean the cover by backflushing debris
from the holes. Replace the suction cover immediately after
cleaning. When reinstalling, orient the cover/strainer with the
small notch at the bottom. The gasket must be inserted into
ENGLISH
the groove of the cover/strainer before reinstalling onto the
suction fitting.
CAUTION: Keep hair a minimum of 6 inches (15,2 cm)
away from the suction fitting at all times when the whirlpool system is operating. Hair longer than shoulder length
should be secured close to the head, or a bathing cap
should be worn. Do not operate the whirlpool system
with the suction cover removed! It is a safety device and
must always be in place on the suction fitting to minimize the potential hazard of hair and body entrapment.
Chromotherapy Lighting
If your unit has Chromotherapy (LED) lighting and the lights
fail to function contact your Jacuzzi Whirlpool Bath dealer.
There are no customer serviceable components on the Chromotherapy lighting.
Replacement fixtures are available from your Jacuzzi
Whirlpool Bath dealer.
IllumatherapyTM Lighting
If your unit has IllumatherapyTM (fiberoptic) lighting and
the lights fail to function contact your Jacuzzi Whirlpool Bath
dealer. There are no customer serviceable components on
the Illumatherapy lighting.
Replacement fixtures are available from your Jacuzzi
Whirlpool Bath dealer.
LED LIGHT ASSEMBLY
LOCKING NUT
LIGHT BEZEL
SHELL
JET WITH FIBEROPTIC LIGHTS
DIN BOX (MOUNTED
ONTO FIBERGLASS SHELL)
LOCKING NUT
LIGHT BEZEL
FIBEROPTIC CABLE
(ROUTED TO WHIRLPOOL
CONTROL BOX)
Jacuzzi Whirlpool Bath DE99000A 3/06
SHELL
FIBEROPTIC CABLES
ROUTED FROM JET TO DIN BOX
22
General Whirlpool Bath Troubleshooting Guide
Pump/Motor does not start.
PROBABLE CAUSES PROBLEM REMEDY
No power to pump/motor.
Pump/motor not plugged in.
Reset GFCI.
Insert plug fully into outlet.
ENGLISH
Pump/Motor operates but no fully
adjustable jets are functioning.
Pump/Motor operates but air is not
injected into water.
Pump/motor does not shutoff.
Pump/motor faulty.
Electronic Control Panel and/or
Control Box defective.
Jets are closed.
Suction cover may be clogged.
Air valves closed.
Electronic Control Panel and/or
Control Box defective.
Electronic Control Panel and/or
Control Box defective.
Replace pump/motor assembly.
Electronic Control Panel/Control Box
wiring disconnected. Check all wiring
and ensure all devices are properly
connected.
Replace Control Panel and/or Control
Box.
Open jets by rotate counterclockwise.
With motor turned off, remove safety
cover and remove any debris. Re-
place suction cover before operating.
Check all wiring and ensure all devices
are properly connected. Replace air
valve(s).
Electronic Control Panel/Control Box
wiring disconnected. Check all wiring
and ensure all devices are properly
connected.
Replace Control Panel and/or Control
Box.
Check all wiring and ensure all devices
are properly connected. Replace
Control Panel and/or Control Box.
If a wall timer is used, the timer is
defective
Water leakage from pump unions.
Pump/motor shuts off by itself or with
wall timer, before set time elapses.
NOTE: If unit is within the warranty period, contact Jacuzzi Whirlpool Bath Service Support at 1 - (800) 288-4002 with bath's serial
number before work is started. The Serial Number is located on the Specification/Serial Number Plate. See page 24.
Overtightened, O-ring may be
pinched or improperly seated, under
tightened.
Motor thermal protection has deactivated pump/motor due to overheating. (Supply voltage low.)
GFCI tripped.
Inadequate supply wiring.
Replace timer.
Untighten unions check and reseat Oring. Lightly coat the O-Rings with
baby-oil or mineral oil. If O-ring has
been pinched out of shape, replace
(refer to number below). When
tightening union nuts, hand tighten
only.
Let motor cool; thermal protection will
reset. Check for proper ventilation.
(Check supply voltage.)
Reset GFCI. If it continues to trip do
not use this unit. Disconnect the unit
and have the problem corrected by a
licensed electrician before using.
Consult a licensed electrician to correct
wiring to unit.
23
Jacuzzi Whirlpool Bath DE99000A 3/06
AUTHORIZED SERVICE
r
If you need a referral for a service company near you, or need assistance with operation or maintenance related
questions, please call our Service Support Department at 1-800-288-4002. Visit our web site at http://www.jacuzzi.com/
for products and services.
To find service agent listings for:
ENGLISH
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
When requesting service or technical assistance please have available both the model and serial number of
your unit. This information can be obtained from the product registration card provided with your unit. If the card
has been misplaced, this information can be obtained from the specification/serial number label on the unit itself
(for location of specification/serial number label see below).
BATH PRODUCTS
Whirlpool baths: The label is located on the wall of the bath near the pump/motor.
Non-jetted baths: The label is located next to the overflow .
SPECIFICATION/SERIAL NUMBER PLATE
CORE NUMBER - SERIAL NUMBER
YOU WILL FIND YOUR
SERIAL NUMBER HERE.
XXXX - XXXXXX
MODEL # XXXXXXX
NAME XXXXX
COLOR XXXXX
MFG # XXXXX
SER # XXXXXX
THIS PRODUCT MEETS OR EXCEED
THE FOLLOWING STANDARDS
BATH & SPA xxxx xxxx.x
SHOWER BASES xxxx xxxx.x
Appropriate Safety Compliance Logos for your unit.
Applicable Electrical Specifications for your unit.
ELECTRICAL SPECIFICATIONS
PRINTED IN THIS AREA
MADE IN
USA
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of
this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
14801 Quorum Dr., Suite 400, Dallas, TX 75254
Printed on Recycled Pape
Jacuzzi Whirlpool Bath DE99000A 3/06
Jacuzzi Whirlpool Bath
Service Support: (800) 288-4002
Printed in the U.S.A.
24
Jacuzzi Whirlpool Bath Limited Warranty
Fuzion Series Bath Product
Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool
Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair
or replace, at its option, the unit or its equipment in accordance with the following terms and conditions.
TWO YEAR LIMITED WARRANTY ON BATHS
Our limited warranty on Designer Collection Bath products is for two (2) years. Our warranty covers the unit and factory-installed
components (e.g., pump, motor) against defects in material or workmanship. Warranty coverage begins on the date the unit was originally
purchased by the user.
FIVE YEAR (PARTS ONLY) LIMITED WARRANTY ON PUMP AND MOTOR
Our limited warranty on the pump and motor is for five (5) years for parts only. Warranty coverage begins on the date the unit was originally
purchased by the user.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
Our limited warranty on options and accessories manufactured by the Company is for ninety (90) days for parts only. Our warranty covers
options and accessories manufactured by the Company (e.g., fill spout kits, trim kits, skirts) against defects in materials or workmanship. Warranty
coverage begins on the date the option or accessory was originally purchased by the user.
Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other person, or resulting
from, without limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.); modification of any type for any reason
(including modification to meet local codes); improper installation (including installation not in accordance with instructions and specifications
provided with the unit); connections supplied by the installer of the equipment; improper voltage supply or unauthorized electrical modification;
misuse; incorrect operation, or lack of proper routine maintenance; operation of the unit without specified minimum amount of water or at
inappropriate water temperature; use of abrasive or improper cleaners; or acts of God, such as lightning, floods, earthquakes, etc.
In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any
cause (e.g., water damage to carpet, ceiling, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts
when pool and/or spa chemicals are used in the unit; optional bath equipment not manufactured by the Company but supplied by Dealer, installer
or the Company; the unit's prior usage as an operational display; or defects that should have been discovered before installation. This limited
warranty does not include: labor, transportation, or other costs incurred in the removal and/or reinstallation of the original unit and/or installation
of a replacement unit; any costs relating to obtaining access for repair; or loss of use damage, including loss of sales, profit or business advantage
of any kind under any circumstances. Bath units are excluded from any warranty coverage if any addition, deletion, or modification of any kind
whatsoever has been made to the unit (or to any component).
Warranty coverage is provided in the United States of America and Canada.
EXCLUSION OF IMPLIED WARRANTIES
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR
TO THE FULL EXTENT ALLOWED BY LAW.
NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties
applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company
will not be responsible for any statements or representations made in any form that go beyond, are broader than or are inconsistent with any
authorized literature or specifications furnished by the Company.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages,
so the above limitations and exclusions may not apply to you.
The attached Warranty Registration Card MUST be filled out by the purchaser within thirty (30) days from purchase and mailed to Jacuzzi
Whirlpool Bath in order for this warranty to become effective.
WARRANTY COVERAGE
WARRANTY LIMITATIONS
RETURN OF WARRANTY CARD
Jacuzzi Whirlpool Bath
14801 Quorum Dr., Suite 400
Dallas, TX 75254
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are
RESPONSIBILITIES OF OTHERS
responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer
of this responsibility. In the event of a problem, the unit must not be installed. The Company is not responsible for failures or damage that could
have been discovered, repaired, or avoided by proper inspection and testing prior to installation.
Damage occurring in transit is the responsibility of the carrier. The user or installer MUST open the crate and inspect the unit for damage when
it is delivered. If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure
of the carrier to respond should be reported to the seller and the carrier. Your freight claims should be filed promptly thereafter.
It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs
relating to obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.
Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter
is the responsibility of the user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (Options and accessories manufactured by the
Company are warranted for ninety (90) days from the original date of purchase for parts only.)
The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these
requirements at the time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city,
county, or state building codes in U.S.A. or municipal or provincial codes in Canada.
For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such
WARRANTY SERVICE
firms are not agents or representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or
type covered by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department
Representative of the nature of the problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided
to the foregoing by the user proving that the failure occurred or was discovered within the warranty period; an authorized independent service person
or Company representative has been permitted to inspect the unit during regular business hours within a reasonable time after the problem was
reported by the user.
In order to obtain warranty service, consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service
Agent. Describe the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service.
If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:
To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied
by the Company, call or write the above. Provide a description of the problem and proof of purchase. You will be instructed how to obtain
replacements and where to return, at your expense, the failed component(s), option(s), or accessory(ies).
All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender
terminates the Company's warranty obligation.
Limited Warranty
Accessory(ies)
Ninety-Day
Parts Only
On
Jacuzzi Whirlpool Bath
Warranty Service Department
14801 Quorum Dr., Suite 400
Dallas, TX 75254
Call: (800) 288-4002
©
2005 Jacuzzi Whirlpool Bath DE99000A 3/06
10.Approximately how long have you lived in this home? ___________
Limited Warranty
Accessory(ies)
Ninety-Day
Parts Only
12. Was your purchase process?
13.How technically aware were you of the patented Jacuzzi
( ) $40,000 to $49,999 ( ) $150,000 and Above
( ) Very easy ( ) Easy ( ) Difficult ( ) Very Difficult
prior to your purchase?
( ) Not aware ( ) Somewhat aware ( ) Very aware
11.Please indicate, approximately, the total annual income of your
( ) 2 weeks- 4 weeks ( ) +2 years
( ) 1 month- 2 months
household.
( ) Up to $24,999 ( ) $50,000 to $74,999
( ) $25,000 to $29,999 ( ) $75,000 to $99,999
( ) $30,000 to $39,999 ( ) $100,000 to $149,999
On
JACUZZI WHIRLPOOL BATH
®
DE99000A
jet system
9. How long did you shop before purchasing unit?
( ) Other (Specify) _____________________________________
( ) 1 day ( ) 2 months- 6 months
( ) 2-7 days ( ) 6 months- 1 year
( ) 1 week- 2 weeks ( ) 1 year- 2 years
Please estimate $ _______________________________________
( ) Eljer ( ) Lasco ( ) Price Pfister ( ) Aqua Glass
( ) Kohler ( ) American Standard ( ) Sterling
5. Who installed? ( ) Already installed/New Home
( ) Contractor/Plumber when remodeling
( ) Self/Spouse when remodeling
( ) Other _____________________________________________
6. What is the current market value of this property?
7. What is the age of the head of the household? ____________ years
8. What other manufacturers did you consider?
Dealer's Address __________________________________________
4. Who finally decided which product you would buy?
( ) Self ( ) Spouse ( ) Self and Spouse Together
( ) Other Family Member ( ) Designer/Architect
( ) Builder/Plumber/Remodeler ( ) Already Installed
3. What was the main reason for purchase?
( ) Styling ( ) Warranty Service ( ) Product Features
( ) Brand Name ( ) Price ( ) Hydrotherapy
( ) Home Resale _______________________________________
( ) Other _____________________________________________
2. Who first gave you specific information about this product (specifications,
( ) Word of Mouth . . . Friend/Relative/Acquaintance
( ) Other (Please Describe) _______________________________
prices, etc.)?
( ) Dealer/Plumbing Supplier ( ) Builder ( ) Remodeler
( ) Plumbing Contractor ( ) Retailer/Home Center Store
( ) Decorator/Architect ( ) Already Installed
1. How did you first hear about this Jacuzzi
( ) Advertisement ( ) Article in Magazine/Newspaper
( ) Visited Dealer/Plumbing Supplier ( ) Yellow Pages
( ) Builder/Plumber/Remodeler ( ) Decorator/Architect
( ) Visited Retailer/Home Center Store
®
product?
This card must be filled out and returned to the address printed on the other
side within thirty (30) days from date of purchase in order for this warranty to
be come effective.
Purchaser's Name _________________________________________
Purchaser's Address _______________________________________
City _____________________________ State ______ Zip ________
Date of Purchase __________________________________________
Model Name ______________________________________________
Serial Number ____________________________________________
Dealer's Name ____________________________________________
Warranty
Registration Card
Loading...