Jacuzzi Finestra FL61000, Finestra 6030, Finestra 6036 Installation & Operation Instructions
FINESTRA WALK-IN BATH
INSTALLATION / OPERATION INSTRUCTIONS
Save These Instructions for Future Use.
Complete and mail in the product registration card provided with your unit.
Write and save the model and serial number of your unit below.
Owner's Record
Date Purchased _________________________________________________________
Purchased From _________________________________________________________
Installed By _____________________________________________________________
Serial Number ___________________________________________________________
Model __________________________________________________________________
Installer: Leave this manual for homeowner.
Homeowner: Read this manual and keep for future reference.
ALSO FIND MANUAL ON-LINE AT JACUZZI.COM
Copyright © 2007 by Jacuzzi Whirlpool Bath FL61000B • October 2007
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY TO PERSONS
WARNING: When using this unit, basic precautions should always be followed, including the following.
WARNING: Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the
manufacturer.
DANGER: To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times.
WARNING: Never drop or insert any object into any opening.
CAUTION: Risk of Electric Shock: The Finestra Bath may have two power sources in which case two disconnect switches are
required to de-energize the unit before servicing.
INSTALLATION
NOTE: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation
according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the
installation of all Jacuzzi Whirlpool Bath products. Our warranty does not cover improper installation related problems.
NOTE: Install this unit in accordance with the Canadian Electrical Code, Part 1.
CAUTION: This equipment is intended for indoor use only. Install the equipment in accordance with these instructions. Use supply
wires that are suitable for 75°C, including the temperature rating of the supply conductors to be used.
This unit should be electrically grounded and installed by a licensed contractor, electrician, and plumber.
Building materials and wiring should be routed away from the motor/pump or blower or other heat producing components of this
unit.
A pressure wire connector is provided on the exterior of the motor/pump and heater to permit connection of an No. 8 AWG (8.4
mm) solid copper bonding conductor between this unit and all other electric equipment and exposed metal in the vicinity, as needed
to comply with local requirements.
WARNING: This unit must be connected only to a supply circuit that is protected by a 15 A ground fault circuit interrupter (GFCI).
Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button.
The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner,
the GFCI is defective. If the GFCI interrupts power to the bathtub without the test button being pushed, a ground current owing,
indicating a possibility of an electric shock. Do not use this hydromassage bathtub. Disconnect the hydromassage bathtub and
have the problem corrected by a qualied service representative before using.
WARNING: (For permanently connected units) A green-colored terminal (or a wire connector) marked “G,” “GR,” “GROUND,”
or “GROUNDING”) is provided within the terminal compartment. To reduce the risk of electric shock, connect the terminal or
connector to the grounding terminal of your electric service or supply panel with a conductor equivalent in size to the circuit
conductors supplying the equipment.
For built-in and drop-in units, install to permit access for servicing.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 2 FL61000B • 10/07
OPERATION
CAUTION: Test the ground fault circuit interrupter protecting this appliance periodically in accordance with manufacturer’s
instructions.
WARNING: Risk of hyperthermia and possible drowning: Water temperature in excess of 104°F (40°C) may be injurious to your
health. Check and adjust water temperature before use.
WARNING: Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of
the body reaches a level several degrees above the normal body temperature of 98.6°F. The symptoms of hyperthermia include an
increase in the internal temperature of the body, dizziness, lethargy, drowsiness and fainting. The effects of hyperthermia include:
• Failure to perceive heat
• Failure to recognize the need to exit the spa or hot tub
• Unawareness of impending hazard
• Fetal damage in pregnant women
• Physical inability to exit the spa or hot tub
• Unconsciousness resulting in danger of drowning
WARNING: Risk of fetal injury: Pregnant or possibly pregnant women should consult a physician before using a hydromassage
bathtub equipped with a heater.
WARNING: The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia. People using medications
or having an adverse medical history should consult a physician before using a hydromassage bathtub equipped with a heater.
WARNING: Risk of hyperthermia and possible drowning: Do not use a hydromassage bathtub equipped with a heater immediately
following strenuous exercise.
WARNING: Do not operate this unit without the guard over the suction tting.
WARNING: Keep body and hair a minimum of 6” (152 mm) away from suction tting at all times when the hydromassage system is
operating. Hair longer than shoulder length should be secured close to the head.
WARNING: Do not tamper with user-operated controls or such devices.
WARNING: Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the
manufacturers.
WARNING: To avoid injury, exercise caution when entering or exiting the hydromassage bathtub.
WARNING: Risk of electrical shock: Do not permit electrical appliances such as a hair dryer, lamp, telephone, radio or television)
within 60” (1.5 m) of this hydromassage bathtub.
• Do not operate hydromassage system unless the bath is lled with water to at least 1-2” (25-51 mm) above highest jet
• Do not immerse the control panel by overlling the bath
• Do not use oil-based bath additives in your hydromassage bath
• When cleaning your bath, do not use abrasive substances which will damage the bath’s surface
• To prevent discoloration of the acrylic nish, do not ll the bath with water in excess of 140°F (60°C)
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
The Company has obtained applicable code (standards) listings generally available on a national basis for products
of this type. It is the responsibility of the installer/owner to determine specic local code compliance prior to installation of the
product. The Company makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 3 FL61000B • 10/07
CONTENTS
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Framing and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Service Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Plumbing and Water Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Water Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Controlling Whirlpool Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Control Panel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Proper Door Closure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Rapid Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Vacuum Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
High Limit Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Pro3 Ozone Sanitation System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Cleaning the Bath . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Repairs to the Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Bath Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Purging the Whirlpool System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Systems Clean™ Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Ozone Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Suction/Intake Cover/Strainer Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Airbath Interconnection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Whirlpool Bath Interconnection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Salon Bath Interconnection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Authorized Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Warranty
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 4 FL61000B • 10/07
SPECIFICATIONS
DRAIN/OVERFLOW
A
B
BACK FRONTLEFT END RIGHT END
L
H
W
14"
1-1/2"
2"
6-1/2"
29-1/2"
16-3/4"
17-1/2"
13-3/4"
Service Access
Service
Access
Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly, heater, plumbing, and ttings
necessary for whirlpool operation. A rotary drain/overow kit is provided for installation on the bath, and an optional remote drain/
overow assembly is also available.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift
the bath by the plumbing at any time; handle by the shell only or the aluminum handles provided at the ends of the unit.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the nish, do not
install the bath. Damage or defect to the nish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool
Bath’s responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for
damage to the carrier. For denitions of warranty coverage and limitations, refer to the published warranty information packed with
the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping.
NOTE: Prior to installation, the bath must be lled with water and operated to check for leaks that may have resulted from shipping
damage or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or
avoided by following this inspection and testing procedure.
SPECIFICATIONS LH=Left Hand, RH=Right Hand
Model
Finestra™ 6030
LH, RH
Finestra™ 6036
LH, RH
Dimensions
60” (1524 mm) L
30” (762 mm) W
38-1/2” (952.5) H
60” (1524 mm) L
36” (914 mm) W
38-1/2” (952.5) H
11-11/16"
Drain/Overow
Dimensions
15” (381 mm) A
11-11/16” (297 mm) B
18” (457 mm) A
11-11/16” (297 mm) B
Cutout
See
below
See
below
Total Weight/Floor
Loading
1038 lb (472 kg),
41.5 lb/ft2 (202 kg/m2)
1177 lb (535 kg),
47.1 lb/ft2 (229 kg/m2)
Operating
Gallonage
55 gal (208 liter) min,
75 gal (284 liter) max
55 gal (208 liter) min,
85 gal (321 liter) max
11-11/16"
Product
Weight
See pages
6 to 11
See pages
6 to 11
Skirt/
Mounting Heater
Integral Factory
installed
Integral Factory
installed
* Add 1/4" to this dimension when roughing-in for 3-wall niche.
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit ( See page 7 to 12).
NOTE: 1. Measurements inside each unit represent cutout in oor to allow for drain/overow.
2. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
3. Service access dimensions given are minimum size.
4. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6.4 mm).
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 5 FL61000B • 10/07
SPECIFICATIONS
60"
30"
17-1/2"
5"
15"
6-5/8"
37"
13-3/4"
20"
4" x 16"
27" H x 24" L
Service Access
Motor
SeatFloor
FINESTRA™ 6030
*Heater
27" H x 9" L
Service Access
Door
Ordering Information
Product Code:
EU50 Finestra™ 6030 Walk-In 14" Seat Whirlpool Bath, LH
EU55 Finestra™ 6030 Walk-In 14" Seat Whirlpool Bath, RH
EY10 Finestra™ 6030 Walk-In 17” Seat Whirlpool Bath, LH
EY15 Finestra™ 6030 Walk-In 17” Seat Whirlpool Bath, RH
EV85 Finestra™ 6030 Walk-In 14" Seat Bath, LH
EV90 Finestra™ 6030 Walk-In 14" Seat Bath, RH
EY00 Finestra™ 6030 Walk-In 17” Seat Bath, LH
EY05 Finestra™ 6030 Walk-In 17” Seat Bath, RH
• Left and Right Hand drain locations
• Standard drain kit, No. FB48827
• Accessories / Hardware:
Remote Drain Kit: #FC30XXX
Pillow: #EK91959
• Trim Kit Finishes Available:
Standard Part No. BN21XXX
(827) – Chrome
(829) – Bright Brass
(898) – Brushed Chrome
(826) – Brushed Nickel
(845) – Oil-Rubbed Bronze
(805) – Platinum
(815) – Satin Nickel
Installation Notes
Refer to installation instructions included with fixture before
beginning installation. Please confirm product availability and
specifications before commencing with any installation work.
PRODUCT SPECIFICATIONS AND AVAILABILITY ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
Technical Specifications
Dimensions
60” L x 30” W x 38-1/2” H
(1524 mm) L x (762 mm) W x (977.9 mm) H
Drain/Overflow
A: 31-1/2” (800 mm) B: 11-11/16” (297 mm)
Cutout
NA
Total Weight
EU50, EU55: 340 lb. (154.5 kg)
EY10, EY15: 340 lb. (154.5 kg)
EV85, EV90: 310 lb. (141 kg)
EY00, EY05: 310 lb. (141 kg)
Operating Gallonage
Max: 75 U.S. Gal. (284 liters)
Min: 55 U.S. Gal. (208 liters)
Product Weight
EU50, EU55: 280 lb. (127 kg)
EY10, EY15: 280 lb. (127 kg)
EV85, EV90: 260 lb. (118 kg)
EY00, EY05: 260 lb. (118 kg)
Skirt Mounting
NA
Electrical Specifications (Models EU50, EU55, EY10, EY15 only)
Motor/Pump and RapidHeat™: 120 VAC, 20 AMP, 60 Hz.
Heater
RapidHeat™: (P/N BN60000) comes standard on;
*(Models EU50, EU55, EY10, and EY15 only)
Finestra™ 6030 Walk-In 14" Seat Whirlpool Bath Left Hand (EU50) shown.
* Measurements inside unit represent cutout in floor to allow for drain/overflow.
Minimum service access dimensions given.
16-3/4"
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 6 FL61000B • 10/07
29-1/2"
BACK FRONTLEFT END RIGHT END
13-3/4"
Service
Access
6-1/2"
L
17-1/2"
Service Access
2"
W
H
A
B
DRAIN/OVERFLOW
14" or 17"
1-1/2"
SPECIFICATIONS
60"
30"
17-1/2"
5"
15"
6-5/8”
37"
13-3/4"
20"
4" x 16"
Motor
SeatFloor
FINESTRA™ 6030
Blower
Heater
27" H x 24" L
Service Access
27" H x 9" L
Service Access
Door
Ordering Information
Product Code:
EW05 Finestra™ 6030 Walk-In 14" Seat Salon™ Spa
Bath, Left Hand
EW10 Finestra™ 6030 Walk-In 14" Seat Salon™ Spa
Bath, Right Hand
EY30 Finestra™ 6030 Walk-In 17" Seat Salon™ Spa
Bath, Left Hand
EY35 Finestra™ 6030 Walk-In 17" Seat Salon™ Spa
Bath, Right Hand
• Left and Right Hand drain locations
• Standard drain kit, No. FB48827
• Accessories / Hardware:
Remote Drain Kit: #FC30XXX
Pillow: #EK91959
• Trim Kit Finishes Available:
Standard Part No. BN21XXX
(827) – Chrome
(829) – Bright Brass
(898) – Brushed Chrome
(826) – Brushed Nickel
(845) – Oil-Rubbed Bronze
(805) – Platinum
(815) – Satin Nickel
Installation Notes
Refer to installation instructions included with fixture before
beginning installation. Please confirm product availability and
specifications before commencing with any installation work.
PRODUCT SPECIFICATIONS AND AVAILABILITY ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
Technical Specifications
Dimensions
60” L x 30” W x 38-1/2” H
(1524 mm) L x (762 mm) W x (977.9 mm) H
Drain/Overflow
A: 31-1/2” (800 mm) B: 11-11/16” (297 mm)
Cutout
NA
Total Weight
EW05, EW10: 360 lb. (163.5 kg)
EY30, EY35: 360 lb. (163.5 kg)
Operating Gallonage
Max: 75 U.S. Gal. (284 liters)
Min: 55 U.S. Gal. (208 liters)
Product Weight
EW05, EW10: 310 lb. (141 kg)
EY30, EY35: 310 lb. (141 kg)
Finestra™ 6030 Walk-In 14" Seat Salon™ Spa Bath Left Hand (EW05) shown.
* Measurements inside unit represent cutout in floor to allow for drain/overflow.
Minimum service access dimensions given.
16-3/4"
29-1/2"
BACK FRONTLEFT END RIGHT END
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 7 FL61000B • 10/07
13-3/4"
Service
Access
6-1/2"
Skirt Mounting
NA
Electrical Specifications
Requires two seperate GFCI protected circuits.
Motor/Pump and RapidHeat™: 240 VAC, 20 AMP, 60 Hz.
Blower: 120 VAC, 20 AMP, 60 Hz.
Heater (Standard)
RapidHeat™: P/N BN60000
L
17-1/2"
Service Access
2"
W
H
14" or 17"
1-1/2"
A
B
DRAIN/OVERFLOW
SPECIFICATIONS
60"
30"
17-1/2"
5"
15"
6-5/8"
37"
13-3/4"
20"
4" x 16"
SeatFloor
FINESTRA™ 6030
Blower
27" H x 24" L
Service Access
27" H x 9" L
Service Access
Door
Ordering Information
Product Code:
EV95 Finestra™ 6030 Walk-In 14" Seat Pure Air Bath,
Left Hand
EW00 Finestra™ 6030 Walk-In 14" Seat Pure Air Bath,
Right Hand
EY20 Finestra™ 6030 Walk-In 17" Seat Pure Air Bath,
Left Hand
EY25 Finestra™ 6030 Walk-In 17" Seat Pure Air Bath,
Right Hand
• Left and Right Hand drain locations
• Standard drain kit, No. FB48827
• Accessories / Hardware:
Remote Drain Kit: #FC30XXX
Pillow: #EK91959
• Trim Kit Finishes Available:
Standard Part No. BN21XXX
(827) – Chrome
(829) – Bright Brass
(898) – Brushed Chrome
(826) – Brushed Nickel
(845) – Oil-Rubbed Bronze
(805) – Platinum
(815) – Satin Nickel
Installation Notes
Refer to installation instructions included with fixture before
beginning installation. Please confirm product availability and
specifications before commencing with any installation work.
PRODUCT SPECIFICATIONS AND AVAILABILITY ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
Technical Specifications
Dimensions
60” L x 30” W x 38-1/2” H
(1524 mm) L x (762 mm) W x (977.9 mm) H
Drain/Overflow
A: 31-1/2” (800 mm) B: 11-11/16” (297 mm)
Cutout
NA
Total Weight
EV95, EW00: 320 lb. (145 kg)
EY20, EY25: 320 lb. (145 kg)
Operating Gallonage
Max: 75 U.S. Gal. (284 liters)
Min: 55 U.S. Gal. (208 liters)
Product Weight
EV95, EW00: 270 lb. (122 kg)
EY20, EY25: 270 lb. (122 kg)
Skirt Mounting
NA
Electrical Specifications
Requires a dedicated GFCI protected separate circuit.
Blower: 115 VAC, 15 AMP, 60 Hz.
Finestra™ 6030 Walk-In 14" Seat Pure Air Bath Left Hand (EV95) shown.
* Measurements inside unit represent cutout in floor to allow for drain/overflow.
Minimum service access dimensions given.
13-3/4"
Service
Access
16-3/4"
29-1/2"
BACK FRONTLEFT END RIGHT END
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 8 FL61000B • 10/07
6-1/2"
L
17-1/2"
Service Access
2"
W
H
14" or 17"
1-1/2"
A
B
DRAIN/OVERFLOW
SPECIFICATIONS
60"
36"
17-1/2"
5"
18"
6-5/8"
37"
13-3/4"
26"
4" x 16"
Motor
SeatFloor
FINESTRA™ 6036
*Heater
27" H x 24" L
Service Access
27" H x 9" L
Service Access
Door
Ordering Information
Product Code:
EU60 Finestra™ 6036 Walk-In 14" Seat Whirlpool Bath, LH
EU65 Finestra™ 6036 Walk-In 14" Seat Whirlpool Bath,
RH
EY50 Finestra™ 6036 Walk-In 17" Seat Whirlpool Bath, LH
EY55 Finestra™ 6036 Walk-In 17" Seat Whirlpool Bath, RH
EW15 Finestra™ 6036 Walk-In 14" Seat Bath, LH
EW20 Finestra™ 6036 Walk-In 14" Seat Bath, RH
EY40 Finestra™ 6036 Walk-In 17" Seat Bath, LH
EY45 Finestra™ 6036 Walk-In 17" Seat Bath, RH
• Left and Right Hand drain locations
• Standard drain kit, No. FB48827
• Accessories / Hardware:
Remote Drain Kit: #FC30XXX
Pillow: #EK91959
• Trim Kit Finishes Available:
Standard Part No. BN21XXX
(827) – Chrome
(829) – Bright Brass
(898) – Brushed Chrome
(826) – Brushed Nickel
(845) – Oil-Rubbed Bronze
(805) – Platinum
(815) – Satin Nickel
Installation Notes
Refer to installation instructions included with fixture before
beginning installation. Please confirm product availability and
specifications before commencing with any installation work.
PRODUCT SPECIFICATIONS AND AVAILABILITY ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
Technical Specifications
Dimensions
60” L x 30” W x 38-1/2” H
(1524 mm) L x (762 mm) W x (977.9 mm) H
Drain/Overflow
A: 31-1/2” (800 mm) B: 11-11/16” (297 mm)
Cutout
NA
Total Weight
EU60, EU65: 360 lb. (163.5 kg)
EY50, EY55: 360 lb. (163.5 kg)
EW15, EW20: 340 lb. (154.5 kg)
EY40, EY45: 340 lb. (154.5 kg)
Operating Gallonage
Max: 85 U.S. Gal. (322 liters)
Min: 70 U.S. Gal. (265 liters)
Product Weight
EU60, EU65: 310 lb. (141 kg)
EY50, EY55: 310 lb. (141 kg)
EW15, EW20: 290 lb. (132 kg)
EY40, EY45: 290 lb. (132 kg)
Skirt Mounting
NA
Electrical Specifications (Models EU60, EU65, EY50, EY55 only)
Motor/Pump and RapidHeat™: 120 VAC, 20 AMP, 60 Hz.
Heater
RapidHeat™: P/N BN60000
*(Models EU60, EU65, EY50, EY55 only)
Finestra™ 6036 Walk-In 14" Seat Whirlpool Bath Left Hand (EU60) shown.
* Measurements inside unit represent cutout in floor to allow for drain/overflow.
Minimum service access dimensions given.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 9 FL61000B • 10/07
16-3/4"
29-1/2"
BACK FRONTLEFT END RIGHT END
13-3/4"
Service
Access
6-1/2"
L
17-1/2"
Service Access
2"
W
H
A
B
DRAIN/OVERFLOW
14" or 17"
1-1/2"
SPECIFICATIONS
60"
36"
17-1/2"
5"
18"
6-5/8"
37"
13-3/4"
26"
4" x 16"
Motor
SeatFloor
FINESTRA™ 6036
Blower
Heater
27" H x 24" L
Service Access
27" H x 9" L
Service Access
Door
Ordering Information
Product Code:
EW35 Finestra™ 6036 Walk-In 14" Seat Salon™ Spa
Bath, Left Hand
EW40 Finestra™ 6036 Walk-In 14" Seat Salon™ Spa
Bath, Right Hand
EY70 Finestra™ 6036 Walk-In 17" Seat Salon™ Spa
Bath, Left Hand
EY75 Finestra™ 6036 Walk-In 17" Seat Salon™ Spa
Bath, Right Hand
• Left and Right Hand drain locations
• Standard drain kit, No. FB48827
• Accessories / Hardware:
Remote Drain Kit: #FC30XXX
Pillow: #EK91959
• Trim Kit Finishes Available:
Standard Part No. BN21XXX
(827) – Chrome
(829) – Bright Brass
(898) – Brushed Chrome
(826) – Brushed Nickel
(845) – Oil-Rubbed Bronze
(805) – Platinum
(815) – Satin Nickel
Installation Notes
Refer to installation instructions included with fixture before
beginning installation. Please confirm product availability and
specifications before commencing with any installation work.
PRODUCT SPECIFICATIONS AND AVAILABILITY ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
Technical Specifications
Dimensions
60” L x 30” W x 38-1/2” H
(1524 mm) L x (762 mm) W x (977.9 mm) H
Drain/Overflow
A: 31-1/2” (800 mm) B: 11-11/16” (297 mm)
Cutout
NA
Total Weight
EW35, EW40: 370 lb. (168 kg)
EY70, EY75: 370 lb. (168 kg)
Operating Gallonage
Max: 85 U.S. Gal. (322 liters)
Min: 70 U.S. Gal. (265 liters)
Product Weight
EW35, EW40: 320 lb. (145 kg)
EY70, EY75: 320 lb. (145 kg)
Finestra™ 6036 Walk-In 14" Seat Salon™ Spa Bath Left Hand (EW35) shown.
* Measurements inside unit represent cutout in floor to allow for drain/overflow.
Minimum service access dimensions given.
16-3/4"
29-1/2"
BACK FRONTLEFT END RIGHT END
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 10 FL61000B • 10/07
13-3/4"
Service
Access
6-1/2"
Skirt Mounting
NA
Electrical Specifications
Requires two seperate GFCI protected circuits.
Motor/Pump and RapidHeat™: 230 VAC, 20 AMP, 60 Hz.
Blower: 120 VAC, 15 AMP, 60 Hz.
Heater (Standard)
RapidHeat™: P/N BN60000
L
17-1/2"
Service Access
2"
W
H
14" or 17"
1-1/2"
A
B
DRAIN/OVERFLOW
SPECIFICATIONS
60"
36"
17-1/2"
5"
18"
6-5/8"
37"
13-3/4"
26"
4" x 16"
SeatFloor
FINESTRA™ 6036
Blower
27" H x 24" L
Service Access
27" H x 9" L
Service Access
Door
Ordering Information
Product Code:
EW25 Finestra™ 6036 Walk-In 14" Seat Pure Air Bath,
Left Hand
EW30 Finestra™ 6036 Walk-In 14" Seat Pure Air Bath,
Right Hand
EY60 Finestra™ 6036 Walk-In 17" Seat Pure Air Bath,
Left Hand
EY65 Finestra™ 6036 Walk-In 17" Seat Pure Air Bath,
Right Hand
• Left and Right Hand drain locations
• Standard drain kit, No. FB48827
• Accessories / Hardware:
Remote Drain Kit: #FC30XXX
Pillow: #EK91959
• Trim Kit Finishes Available:
Standard Part No. BN21XXX
(827) – Chrome
(829) – Bright Brass
(898) – Brushed Chrome
(826) – Brushed Nickel
(845) – Oil-Rubbed Bronze
(805) – Platinum
(815) – Satin Nickel
Installation Notes
Refer to installation instructions included with fixture before
beginning installation. Please confirm product availability and
specifications before commencing with any installation work.
PRODUCT SPECIFICATIONS AND AVAILABILITY ARE SUBJECT TO
CHANGE WITHOUT NOTICE.
Technical Specifications
Dimensions
60” L x 30” W x 38-1/2” H
(1524 mm) L x (762 mm) W x (977.9 mm) H
Drain/Overflow
A: 31-1/2” (800 mm) B: 11-11/16” (297 mm)
Cutout
NA
Total Weight
EW25, EW30: 350 lb. (159 kg)
EY60, EY65: 350 lb. (159 kg)
Operating Gallonage
Max: 85 U.S. Gal. (322 liters)
Min: 70 U.S. Gal. (265 liters)
Product Weight
EW25, EW30: 300 lb. (136 kg)
EY60, EY65: 300 lb. (136 kg)
Finestra™ 6036 Walk-In 14" Seat Pure Air Bath Left Hand (EW25) shown.
* Measurements inside unit represent cutout in floor to allow for drain/overflow.
Minimum service access dimensions given.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 11 FL61000B • 10/07
16-3/4"
29-1/2"
BACK FRONTLEFT END RIGHT END
13-3/4"
Service
Access
6-1/2"
Skirt Mounting
NA
Electrical Specifications
Requires a dedicated GFCI protected separate circuit.
Blower: 115 VAC, 15 AMP, 60 Hz.
L
17-1/2"
Service Access
2"
W
H
14" or 17"
1-1/2"
A
B
DRAIN/OVERFLOW
INSTALLATION
Framing and Support
The drain/overow of the bath extends below the bottom of
the bath. Note that this requires a cutout in the oor.
The oor structure beneath the bath must be able to
support a total weight of bath, water, and bather. For the
total weight of the unit, please refer to the specication
sheet for your model (pages 5 to 11). The unit must be
supported from the bottom of the bath and not from the bath
rim or tile ange. If the suboor is level and a continuous
surface, no other preparation is necessary. You can proceed
to install the bath. If the suboor is not level, you MUST make
sure that the level legs are making contact with the suboor
and that the unit is perfectly leveled. Both sides of a joint
or splice of suboor should be level to each other. When
attaching baths with anges to stud wall, use shims to ll
any gaps between the bath ange and studs, please refer
to gure below, Optional Tile Flange Kit.
The rim of the bath is not designed to support weight. If nish
material is to overlap or contact the bath, the added weight
must be fully self-supporting.
Motor or
adhesive
Sub-oor
Sealant
Tile
Flashing
Flange
Nail or
screw
The protective lm liner inside the bath is used to
prevent damage to the nish during installation. Before
installation, remove liner to inspect for any defects,
reapply and do not remove until nal cleanup.
IMPORTANT: If a skirt is to be used, it must be installed at the
time of unit installation – refer to skirt installation instructions.
Install optional trim parts when all installation has been
completed.
In some cases, access may not have been provided because
of the design of the bath environment and having full
understanding that in this case, it may be necessary to remove
the unit for service.
If this is the case, diagnosing a problem may not be possible
without complete access to the plumbing system. This would
necessitate the removal of the unit. Although this practice is
not commonly implemented, it is an acceptable method.
If service access has not been provided, it is the home owners
responsibility to remove the bath and provide the required
access, should a repair become necessary.
Finishing material
Mortar
Cement board
Plastic
ller
Silicone
sealant
Bath
rim
Service Access
Allow for access to service connections. It is
the installer's responsibility to provide sufcient
service access. The recommended minimum
18 inches allowable for service to the bath are
shown in the "Service Access" illustration.
Provide adequate area around unit for air
circulation for cooling the motor and to supply
sufcient air to the jets. Do not insulate this area
or around motor.
1 x 4” (Not
for support)
SEMI-SUNKEN
Stud
wall
1 x 4” (Not
for support)
OPTIONAL TILE
FLANGE KIT
Stud
Flange
Shim if
necessary to ll
gaps between
stud and ange
Caulking
1/8”
Gap
Tile
Cement
board
Tile
adhesive
Attach
with
screws
provided
Flange
Stud
Stud
Flange
Shim if
necessary to ll
gaps between
stud and ange
Caulking
1/8”
Gap
Tile
Stud
INTEGRAL SKIRTED VERSION DROP-IN (3-Wall tile ange)
Cement
board
Tile
adhesive
Attach
with
screws
provided
Flange
1 x 4”
(Not for
support)
Walls (3 Sides)Tile Flanges (3 Sides)
18 in
Service Access Required
THREE-WALL NICH (Top View)
WITH SERVICE ACCESS
CAUTION: When installing Finestra in a
three-wall niche, an approved tile ange kit
must be used or a factory-installed ange.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 12 FL61000B • 10/07
LEVEL ADJUSTMENT
Nut (Top)
Rail
Threaded
Levelintg
Leg
(Floor)
Foot
Nut (Bottom)
The Finestra comes factory pre-leveled however the oor may require a need to make
adjustment. The leveling legs operate in a manner as those in a washer-dryer.
NOTE: It is important check the level prior to water testing. The unit must be level for
water testing as this helps with the door seal alignment.
If it is necessary to level the bath, start by leveling the outside four legs, then move to
the two legs on the door. The unit is preleveled prior to shipment and should not be
tampered with if not required.
CAUTION: Under no circumstances will it be necessary to remove the levelling feet.
Leveling Legs
ELECTRICAL CONNECTIONS
All circuits must be protected by a dedicated Ground Fault Circuit Interrupter (GFCI). Refer to the electrical specication for each
model on pages 5-11. Install duplex outlets to the studwall underneath the bathtub, at least 4 inches (102 mm) above the oor or in
accordance with local building or electrical codes. Duplex outlets are not provided. Because these units are manufactured with an
electronic control panel, no remote switch or timer is necessary.
With a #8 solid copper wire, bond the heater to the house electrical panel or approved local bond. A bonding lug is provided on the
heater. With another #8 solid copper wire, bond the pump/motor to the house electrical panel or approved local bond. A bonding
lug is provided on the pump/motor.
At initial start-up and before each use thereafter with power ON, push the dedicated GFCI test button on each circuit. The reset
button should pop out. Push this button in to reset. If the interrupter fails to operate in this manner, there is a ground current
owing or a device malfunction, indicating the possibility of electrical shock. Turn off power and do not use the bath until the
source of the problem has been identied and corrected.
DANGER: RISK OF ELECTRIC SHOCK. Connect only to a circuit protected by a dedicated Ground Fault Circuit Interrupter
(GFCI).
CAUTION: Operating the motor/pump without enough water in the bath can cause leaking and permanent damage to the pump.
Before power is applied to the installation, make sure the switch is in the OFF position to avoid pump damage.
It is necessary to install separate dedicated GFCI protected circuits for both duplex receptacles (not provided).
ELECTRICAL CONNECTION
1. The motor is connector the the Control Box.
2. The Control Box is connected to the Ozone unit.
3. The Ozone unit is connected to the power receptacle.
NOTE: The heater is conected independently.
Blower
Ozone unit
Blower
Motor
Power
connector
Motor
Right side of unit
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 13 FL61000B • 10/07
Rapid heater
Control box
Left side of unit
PLUMBLING AND WATER SUPPLY
Drain Information
A drain/overow assembly provided with the tub must be installed on the bath, water tested, and connected to the sanitary system
of the house. After opening the carton, inspect for damage and verify that the kit is of the proper nish. In the Jacuzzi Whirlpool
Bath drain/overow kit, note that the waste ange, strainer, overow cover and cover screws are packaged in a separate package
within the kit to protect the trim nish. Follow the installation instructions provided with the drain/overow kit. After the drain is fully
installed, test for proper drainage. If the unit does not drain properly, rectify this condition before proceeding with the installation.
Jacuzzi Whirlpool Bath is not responsible for removal or reinstallation costs.
NOTE: Watertight installation of the drain is the installer’s responsibility. Drain leakage is excluded from the Jacuzzi Whirlpool Bath
warranty of this product.
Plumbing
Pump, jets, and suction ttings for the whirlpool system are factory plumbed in schedule 40 PVC piping.
All Jacuzzi Whirlpool Bath products are factory tested for proper operation and watertight connections prior to shipping. If leaks are
detected, notify your Jacuzzi Whirlpool Bath dealer. Do not install the unit.
Anti-Siphon Valve
Optional Anti-Siphon valve installation. Anti-Siphon valve is not supplied with the tub. Consult your local plumbing code
requirements for the minimum height above the tub rim.
Water Supply
Consult local authorities for plumbing code requirements in your area.
IMPORTANT: Proper installation of the ll spout plumbing and compliance with local codes are the responsibility of the installer.
Jacuzzi Whirlpool Bath does not warrant connections of water supply ttings and piping, ll systems, or drain/overow systems.
Nor is it responsible for damage to the bath which occurs during installation.
CAUTION: A nonammable protective barrier must be placed between soldering work and bath unit to prevent damage to the bath.
Shower Information
Because of the Walk-In baths’ unique design, a rigid shower door cannot readily be installed. If a shower is desired, we
recommend a hand-held shower be installed in conjunction with a shower curtain, as this will allow the user to control the direction
of the spray.
NOTE: Proper installation of a shower is the responsibility of the installer. Jacuzzi Whirlpool Bath is not responsible for damage to
the unit or for water damage which might occur due to its installation.
Clean-Up After Installation
To avoid dulling and scratching the surface of the bath, never use abrasive cleaners. A mild liquid detergent and warm water will
clean soiled surfaces. Remove spilled plaster with a wood or plastic edge. Metal tools will scratch the surface. Spots left by plaster
or grout can be removed if lightly rubbed with detergent on a damp cloth or sponge.
NOTE: Paint, tar, or other difcult surface stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing
alcohol).
Minor scratches which do not penetrate the color nish can be removed by lightly sanding with 600-grit wet/dry sandpaper. You
can restore the glossy nish to the acrylic surface of the bath with a special compound, Meguiar’s #10 Mirror Glaze. If that is not
available, use automotive rubbing compound followed by an application of automotive paste wax.
Major scratches and gouges which penetrate the acrylic surface will require renishing. Ask your Jacuzzi Whirlpool Bath dealer for
special instructions or visit our web site at http://www.jacuzzi.com/.
Drain Kits
Rotary Drain Kit. A PVC Rotary Drain Kit comes with a 43 inch cable length, please see the manufacturer's instructions included
with the kit.
Remote Drain Kit. An optional PVC Remote Drain Kit comes with a 50 inch cable length, please see the manufacturer's instructions
included with the kit. A template will be provided.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 14 FL61000B • 10/07
1" - 2"
FILL TO AT LEAST
1" - 2" ABOVE HIGHEST JET
DIRECTIONALLY
ADJUSTABLE
FULLY
ADJUSTABLE
JETS
OPERATION
NOTE: These instructions pertain to all bath products
manufactured by Jacuzzi Whirlpool Bath. Not all features
discussed in this instruction pamphlet apply to all baths.
the handles to the right (clockwise). Customize water force by
lowering water volume of one (1) jet(s) to increase water force
in another jet(s). In units with 2 speed motors the water force
can be increased or decreased using the electronic control.
Never run the whirlpool system with all the jets closed.
All baths manufactured by Jacuzzi Whirlpool Bath are
designed for “ll and drain,” which means the bath should
be drained after each use and lled with fresh water by the
next bather. This is a health precaution, as these baths are
not designed to hold water continuously like pools or spas.
If you want a unit designed to continuously hold water, see
your Jacuzzi Whirlpool Bath dealer for the complete line of
whirlpool spas available.
Once the bath is installed, remove any residue or foreign
materials left over from construction.
NOTE: Use these chemicals only on SURFACE stains. Other
dirt can be cleaned off with a mild liquid detergent on a damp
cloth. Scrape off plaster with a wooden or plastic edge; do
not use metal scrapers, wire brushes or other metal tools,
as they will damage the bath’s surface.
FORCE OF AIR: For units with electronic controls the Force
of Air is controlled electronically. Refer to the Electronic Control
Panel instructions for details in adjusting Force of Air. Units
with manual controls are discussed on page 22.
Water Level
Close the drain and ll the bath until water is at least 1” to 2”
(2.5 to 5.08 cm) above the highest jet (see water line indicated
in the illustration). Do not turn on the whirlpool system at any
time if the jets are not completely immersed in water. Do not
immerse the control panel by overlling the bath. Running
the whirlpool system when there is insufcient water in the
bath could result in water spraying outside the bath area.
Running the whirlpool system without water will damage the
recirculating pump.
IMPORTANT: When exiting the bath, the water level will drop
below the jets which could result in water being sprayed out
of the unit. To prevent this, you must turn unit off before
exiting bath.
CONTROL PANEL OPERATION
All tubs in this product line come with electronic controls and
standard Chromotherapy. Read and follow the operation
instructions for the control system of your unit.
Controlling Whirlpool Action
The whirlpool action in your bath, controlled manually and
electronically, is inuenced by three factors – direction of ow,
force of water, and force of air. Every bath manufactured by
Jacuzzi Whirlpool Bath that is equipped with fully adjustable
PowerPro® jets, are manually adjustable for direction and
water force. Some baths have additional jets which can be
adjusted for direction only. Baths equipped with 2 speed
motors and electronic controls can also inuence water force
and force of air.
DIRECTION: To change the direction of the water ow, swivel
the jet nozzle to the desired angle. The jets can be directed
individually toward any location on your body to provide a
hydromassage. The jets can also be adjusted so that they all
point in the same direction (clockwise or counterclockwise)
to circulate the water in a circular motion around the bath,
causing a total whirlpool effect.
WATER FORCE: The high volume, fully adjustable
PowerPro® jets can be manually adjusted to control the
force of the water coming into the bath. For robust action,
increase the force of the ow by rotating the jet handles to
the left (counterclockwise). For a more gentle effect, rotate
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 15 FL61000B • 10/07
General Functions
This Jacuzzi tub is equipped with an electronic control panel.
The seven button panel controls a two speed pump/motor,
Chromotherapy lighting, air controls, wave control, and in
some units the blower. LED lights (in the control panel)
indicate function levels. When switching between functions,
the LED for the inactive functions will dim and the active
function will brighten.
The bath is equipped with a water level sensor(s). When the
water level is below the sensor, the pump/motor can not be
activated. If the ON/OFF pump/motor button is pressed at
this time, the pump/motor will not operate. When the water
goes above the water level sensor, the pump/motor can be
activated. If the water level drops below the level sensor, the
pump/motor will shut OFF. To restart the pump/motor after
the water level goes above the level sensor, the ON/OFF
pump/motor button must be pressed. The pump/motor will
automatically shut off 30 minutes after the pump/motor was
turned on.
NOTE: Ensure the water level sensor located inside the bath
is free of any soap or dirt buildup.
Pump/Motor Switch (ON/OFF )
Pressing the button will turn ON the two speed
pump/motor at HIGH speed. Pressing a second
time will turn OFF the pump/motor. To change
speeds use the Toggle buttons.
Pump/Motor Status LED
When the pump/motor is ON at HIGH speed all
four LED indicator lights will be lit. When the
pump/motor is ON at LOW speed the bottom LED
indicator light will be lit.
Left Air Valve Switch
Pressing this button will activate the left air valves
using the Toggle buttons to increase/decrease
air ow to the left set of jets. The air ow can be
adjusted from no air to maximum air.
Left Air Valve Status LED
The Left Air Valve Status LED will show four LED
lights at maximum air and only one LED light
when the air is turned OFF. Each additional LED
indicates more air ow.
Right Air Valve Switch
Pressing this button will activate the right air
valves. Use the Toggle buttons to increase/
decrease air ow to the right set of jets. The air
ow can be adjusted from no air to maximum air.
Right Air Valve Status LED
The Right Air Valve Status LED will show four
LED lights at maximum air and only one LED light
when the air is turned OFF. Each additional LED
indicates more air ow.
Bath Light Switch (ON/OFF )
Pressing this button will turn ON the white bath
light(s). Pressing the Toggle buttons at this time
will increase or decrease light intensity.
Pressing the button a second time will access
the saved favorite color. To cycle lighting colors
use the Toggle button. Pressing the Toggle
button again will stop the light cycling. The color
displayed when the cycle has been stopped will be
saved as your favorite color.
Pressing the button a third time to turn OFF the
light.
Wave Function Switch (ON/OFF )
Pressing this button activates wave action by
opening and closing air valves. Pressing a second
time will turn OFF the wave action.
When pressing this button after pressing the
Pump/Motor button or the Air Valve button, the
wave action will work on both Right and Left Air
valves.
NOTE: When switching between functions, the LED for
the inactive functions will dim and the active function will
brighten.
Control Panel Switches
Left air valve,
Status LEDs
status LEDs
Left air
valve
On-Off
Pump/
Motor
Bath
light
Wave
function
Air Bath Switch
Pressing this button will activate the blower using
the Toggle buttons to increase/decrease air ow
from the blower. Blower air can be adjusted from
low air to maximum air.
Air Bath Status LED
The Air Bath Status LED will show four LED lights
at maximum air and only one LED light when the
air is turned OFF. Each additional LED indicates
more air ow.
Toggle Switches
The Toggle buttons, up and down , act on each of
the other switches to increase, decrease, or modify
functionality. Use the up arrow to increase and the
down arrow to decrease.
• Pressing a toggle button after pressing the
Pump/Motor button will increase or decrease
speeds on the Pump/Motor. If the pump/motor
is on HIGH speed press the down arrow to
select LOW speed. If the pump/motor is on
LOW speed press the up arrow to select HIGH
speed.
• Pressing an up or down toggle button after
pressing the Bath Light button once will
increase or decrease the white light brightness.
Pressing an up or down toggle button after
pressing the Bath Light button twice will begin
cycling the light colors.
Leave the colors cycling or press the same
toggle button again to stop the color cycling.
With the lights stopped on a color pressing the
Bath Light button a third time will turn OFF the
light. (A favorite color will be saved ONLY when
the cycling has been stopped on that color and
then turned OFF.)
(Continued)
Right air
valve
Toggle
switches
Right air
valve,
Status LEDs
Air bathPump/Motor
Blower
status
LEDs
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 16 FL61000B • 10/07
(Continued)
• Pressing a toggle button after pressing both
the Pump/Motor button rst and then the Wave
Function button will increase or decrease wave
action on both air valves.
Pressing a toggle button after pressing either
Air Valve buttons increase or decrease wave
action on that air valve.
• Pressing a toggle button after pressing the Air
Bath Switch increase or decrease the air ow
through the bottom air channels
The rubber strip with a double seal will prevent leakage and
also provide a visual check before lling the bath with water.
The gure shows the rubber strip in a fully closed position. The
view shows the rubber seal from the top.
NOTE: The rubber strip has a double seal. When the door is
open the seals are open (left); with the door closed, the seals
are closed (right).
RAPIDHEAT™
These units have a RapidHeat™ heater installed on the
intake or discharge lines. The heater will help maintain the
temperature of the water in the bath. RapidHeat™ requires
a separate dedicated 120 VAC, 15 A GFCI receptacle.
NOTE: When switching between functions, the LED for
the inactive functions will dim and the active function will
brighten.
PROPER DOOR CLOSURE
The door uses a magnetic seal with a handle to fasten the
door and a rubber strip with a double seal. The following
instructions provide details on how to make sure the proper
seal is achieve and on the use of the door handle. Proper
closure will will prevent any water leakage.
WARNING: The equipment uses a magnetic seal on the
door that is capable of pinching your ngers in the door.
The magnetic door is perfectly safe, but may affect a heath
device as a pacemaker if either the edge of the door or the
inside edge of the door frame come in direct contact with the
immediate area of the device.
The door opens towards the inside of the bath. Note the open
and closed positions of the door handle are illustrated. Use
the handle to fasten the door to reinforce proper closure. The
magnetic strip along the edge of the door and the inside edge
of the door frame is unseen, and ensures a proper seal.
Open
position
Closed
position
Operation
With the heater installed and the whirlpool pump is operating,
the heating function is totally automatic. No user control
required.
Vacuum/Pressure Switch
The heater is equipped with a preset vacuum/pressure switch
which will not allow the heater to turn ON if the pump is not
running with water owing through the whirlpool system.
High-Limit Switch
The heater includes an exclusive High-Limit switch. This
safety circuit will not false trip from hot tap water. It will only
turn off the heater if the thermostat fails. To reset, press the
button.
Reset switch Heater ON indicator
HEATER ON
rapid heat
Use of Door Handle
Door open Door closed
Double seals
fully closed
Door is closed (see detail at right
Detail of double seals closed
Check Seal Closure
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 17 FL61000B • 10/07
OVERHEAT
PROTECTION
PUSH TO RESET
Rapid Heat Controls
If the high-limit trips frequently, contact your Authorized
Electrical/Mechanical Service Provider. Visit our web site at
http://www.jacuzzi.com/.
To nd service agent listings for:
Electrical or Mechanical Repairs visit
http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit
http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit
http://jacuzzi.com/pdf/MPD.PDF
PrO3 Ozone Sanitation System
The unit has a PrO3 Ozone Sanitation System installed. The
ozone generator is set to operate as follows.
At the time the power is initiated, the ozone operates for thirty
minutes, and then it will automatically shut off. Thereafter,
every four hours, the ozone will operate for thirty minutes
automatically and continuously.
NOTE: A soft noise is produced by the pump during operation
of the equipment.
To Set Timer
Determine the best time for the ozone generator to operate.
The ozone generator should be programmed to operate when
the air bath is not in use. Six hours before use, interrupt the
power to the air bath at the dedicated GFCI circuit breaker. Be
sure to observe all safety precautions. When the dedicated
GFCI circuit comes back on, the system is activated and the
ozone timer is set to begin a regular cycle as scheduled.
CAUTION: In the event of a power outage, the timer period will
need to be reset.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 18 FL61000B • 10/07
MAINTENANCE
Cleaning the Bath
To clean your bath, simply use a mild, nonabrasive liquid
detergent solution. You can protect and restore the gloss to a
dulled acrylic surface by applying Meguiar’s #10 Mirror Glaze,
a product specically designed for use on acrylic nishes. If
Meguiar’s is not available, an acrylic polish of equal quality or
automotive paste wax is acceptable.
Never use abrasive household cleaners on any Jacuzzi
Whirlpool Bath product.
Repairs to the Surface
Minor scratches which do not penetrate the color nish can be
removed by lightly sanding with 600-grit wet/dry sandpaper.
Restore the gloss using Meguiar’s Mirror Glaze or automotive
paste wax.
Major scratches and gouges which penetrate the acrylic
surface will require renishing. Ask your Jacuzzi Whirlpool
Bath dealer for special instructions.
Bath Additives
NOTE: Do not use oil or oil-based bath additives.
If you want to use any kind of bath additive, use only a small
amount of low-foaming powder or crystal substance; the
whirlpool action intensies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath additives
may increase the level of accumulations of bath residue in the
whirlpool system. If excess accumulations persist, you should
discontinue use of these products.
Purging the Whirlpool System
NOTE: The Whirlpool System should be purged at least twice
a month.
To remove accumulations of bath residue from the whirlpool
system, it is recommended that a whirlpool bath be purged
at least twice a month. For best results, however, we
recommend that you purge your whirlpool bath after each
use using, Systems Clean™, our exclusive two-part plumbing
system cleaner made specically for whirlpool baths.
Systems Clean™ is available through an authorized Jacuzzi
Whirlpool Bath distributor or by calling us direct at 1-800-288-
4002.
Systems Clean™ Instructions
Refer to the instructions on the Systems Clean™ packet.
CAUTION: Do not use while bathing! Use extreme caution
when handling this product!
Immediately after bathing and exiting the whirlpool bath,
leave the bath water in the tub and add more hot water. The
water level in the tub must be at least 2” (5,08 cm) above the
highest jet.
NOTE: Inducted air from the hydromassage system will cause
the Systems Clean™ contents to foam increasing odor.
Turn OFF the whirlpool air control or turn it to the lowest
setting and pour in the entire contents of PACKET #1 ONLY
directly into the bath water. For best results, pour the System
Clean into the tub near the intake for the circulation pump and
be sure to avoid contact with your skin. Allow the whirlpool
to run for 30 seconds and then add PACKET #2 ONLY. It is
important to use Packet #1 before Packet #2 to avoid a
strong odor. Allow the bath to run for 5 to 10 minutes then
drain the tub completely. Rell the tub with cold water and run
for 2 to 3 minutes. Drain completely and rinse off any residue.
Remember to reset the air valves to your bathing comfort
level.
DANGER: Harmful if swallowed. Eye irritant. Protect your
eyes, skin and mucus membranes from contact with this
product or its concentrated solution. A strong alkaline product
can cause severe burns to the eyes and skin.
If you have followed the standard purging instructions above
and still have an excess accumulation of bath residue and
desire an alternative cleaning mechanism, we recommend
SUPER SYSTEMS CLEAN™ PLUS manufactured by Stearns
Packaging to rectify this condition. This may be obtained by
contacting us at 1-800-288-4002. It is recommended that
you follow the instructions provided by the manufacturer
with the product. Repeated use may be necessary. SUPER
SYSTEMS CLEAN™ PLUS does not replace the necessity to
regularly purge your whirlpool system with Systems Clean™
as recommended.
Ozone Maintenance
The PrO3 Ozone Sanitation System is a maintenance-free
system. All that is required is the regular system cleaning
using the Systems Clean™ as directed.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 19 FL61000B • 10/07
MAINTENANCE
NOTCH
GASKET
COVER STRAINER
SCREW
SUCTION
FITTING
SUCTION COVER/STRAINER ASSEMBLY
Suction/Intake Cover/Strainer Maintenance
Clean the suction/intake cover/strainer of hair and debris
when necessary. To do this, remove the center screw and
detach the square cover. Clean the cover by backushing
debris from the holes. Replace the suction/intake cover
immediately after cleaning. Be careful not to overtighten the
screw. When reinstalling, orient the cover/strainer with the
small notch at the bottom. The gasket must be inserted into
the groove of the cover/strainer before reinstalling onto the
suction tting.
CAUTION: Keep hair a minimum of 6 inches (15.2 cm) away
from the suction/intake tting at all times when the whirlpool
system is operating. Hair longer than shoulder length should
be secured close to the head, or a bathing cap should be
worn. Do not operate the whirlpool system with the suction/
intake cover removed! It is a safety device and must always
be in place on the suction tting to minimize the potential
hazard of hair and/or body entrapment.
Interconnection of Airbath, Whirlpool, and
Salon Baths
The interconnection of the airbath, whirlpool bath, and salon
bath is shown in the following gures.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 20 FL61000B • 10/07
AIRBATH INTERCONNECTION DIAGRAM
The Airbath equipment is shown in the following gure. It
shows the only acceptable manner in which the system
components may be interconnected for efcient and safe
operation. If the equipment is not congured as shown in
the gure, the equipment may not operate or it may result
in damage to the equipment
MODEL NUMBERS
EV95, EW00, EW25, EW30,
EY20, EY25, EY60, and EY75
See Specications for details
ELECTRICAL SPECS
Requires a separate dedicated GFCI protected circuit
Blower: 115 VAC, 15 A, 60 Hz
A
B
D
E
C
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 21 FL61000B • 10/07
F
LEGEND
A Water sensors
B Blower
C Ozone system
D Control panel
E Control box
F GFCI Plug, 15 A
WHIRLPOOL BATH INTERCONNECTION DIAGRAM
The Whirlpool bath equipment is shown in the following
gure. It shows the only acceptable manner in which the
system components may be interconnected for efcient and
safe operation. If the equipment is not congured as shown
in the gure, the equipment may not operate or it may result
in damage to the equipment
MODEL NUMBERS
EU50, EU55, EU60, EU65,
EY10, EY15, EY50, and EY55,
See Specications for details
ELECTRICAL SPECS
Requires a separate dedicated GFCI protected circuit
RapidHeat, 120 VAC, 20 A, 60 Hz
PN BN60000 (EU60, EU65, EY50, and EY55 only)
A
H
G
B
C
D
E
F
LEGEND
A Heater
B Pump/motor
C Control panel
D Control box
E Chromatherapy light
F Electronic air switch
G GFCI Plug, 20 A
H Ozone system
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 22 FL61000B • 10/07
H
J
I
MODEL NUMBERS
EW05, EW10, EW30, EW35, EW40,
EY30, EY35, EY70, and EY75
See Specications for details
ELECTRICAL SPECS
Requires two separate dedicated GFCI protected separate circuits
Motor/Pump and RapidHeat, 230 VAC, 20 A, 60 Hz RapidHeat,
PN BN60000
B
G
D
F
E
K
dedicated GFCI receptacle
I Fuse box
J RapidHeat™
K Electronic air switch
L Water sensors
----------
protected breaker
*PLug into separate
**Plug into separate GFCI
SALON BATH INTERCONNECTION DIAGRAM
The Salon bath equipment is shown in the following gure.
It shows the only acceptable manner in which the system
components may be interconnected for efcient and safe
operation. If the equipment is not congured as shown in
the gure, the equipment may not operate or it may result
in damage to the equipment
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 23 FL61000B • 10/07
C
A
L
LEGEND
A Blower
B GFCI Receptacle, 15 A*
C Ozone system
D Control panel
E Pump/motor
F Chromatherapy light
G Control box
H GFCI Plug, 230 V, 20 A**
TROUBLESHOOTING GUIDE
PROBLEM PROBABLE CAUSES REMEDY
Pump/motor does not start No power to pump/motor Reset dedicated GFCI
Pump/motor not plugged in Insert plug fully into the control box motor connector
Pump/motor faulty Replace pump/motor assembly
Jets are closed Open jets by rotating counterclockwise
Control panel cable disconnected Check the control cable between the control panel
Dirty water sensor Damage or disconnected cable at water sensor, water
and the control box. Reconnect if necessary
too pure
Pump/motor operates but no fully
adjustable jets are functioning
Pump/motor operates but air is not
injected into water
Water leakage from pump unions Overtightened; O-ring may be pinched or
Pump/motor shuts off by itself before
set time elapses
Control panel not responding No power to control box Power down the system by either unplugging the unit or
Suction cover may be clogged With motor turned off, remove safety cover and
Air valves are closed Use electronic controls to open air valves. Reset air
improperly seated; under tightened
Motor thermal protection has deactivated pump/
motor due to overheating (Supply voltage low)
Dedicated GFCI tripped Reset dedicated GFCI. If it continues to trip, do not
Inadequate supply wiring Consult a licensed electrician to correct wiring to unit
remove any debris. Clean thoroughly before
replacing. Replace suction cover before operating
valves to allow air ow
Untighten unions to check and reseat O-ring. If
O-ring has been pinched out of shape, replace (see
phone number below. When tightening union nuts,
hand tighten only
Let motor cool; thermal protection will reset. Check
for proper ventilation (Check supply voltage)
use this unit. Disconnect the unit and have problem
corrected by a licensed electrician before using
shutting off the power at the house breaker panel. Wait
15 seconds then power back up. Retry the system by
activating the feature that was not responding
Lighting does not work Cable disconnected or broken Unplug and reconnect cable from the control box to
Door does not seal properly Door is not properly closed Make sure the latches are engaged
Improperly leveled legs Make sure bath is level
Seal is dirty or particles are on the seal Clean seal with a non-alcohol cleaner
NOTE: If unit is within the warranty period, contact Jacuzi Whirlpool Bath Service Support at 1-800-288-4002 with bath’s serial
number before work is started. The serial number is located on the specication/serial number plate (see Page 25)
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 24 FL61000B • 10/07
the light. Replace the cable
MODEL # XXXXXXX
NAME XXXXX
COLOR XXXXX
MFG # XXXXX
SER # XXXXXX
MADE IN
USA
THIS PRODUCT MEETS OR EXCEED
THE FOLLOWING STANDARDS
BATH & SPA xxxx xxxx.x
SHOWER BASES xxxx xxxx.x
SPECIFICATION/SERIAL NUMBER PLATE
YOU WILL FIND YOUR
SERIAL NUMBER HERE.
XXXX - XXXXXX
Applicable Electrical Specifications for your unit.
Appropriate Safety Compliance Logos for your unit.
CORE NUMBER - SERIAL NUMBER
ELECTRICAL SPECIFICATIONS
PRINTED IN THIS AREA
AUTHORIZED SERVICE
If you need a referral for a service company near you, or need assistance with operation or maintenance related questions, please
call our Service Support Department at 1-800-288-4002. Visit our web site at http://www.jacuzzi.com/ for products, services, and
an on-line copy of these Installation and Operation Instructions.
To nd service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
When requesting service or technical assistance please have available both the model and serial number of your unit. This
information can be obtained from the product registration card provided with your unit. If the card has been misplaced, this
information can be obtained from the specication/serial number label on the unit itself (for location of specication/serial number
label see below).
BATH PRODUCTS
Whirlpool baths: The label is located on the wall of the bath near the pump/motor.
Non-jetted baths: The label is located next to the overow.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this
type. It is the responsibility of the installer/owner to determine specic local code compliance prior to installation of the product.
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 25 FL61000B • 10/07
Jacuzzi Whirlpool Bath
14525 Monte Vista Avenue
Chino, California 91710
THIS PAGE INTENTIONALLY LEFT BLANK
Jacuzzi Whirlpool Bath: Finestra Walk-in Bath Page 26 FL61000B • 10/07
Limited Lifetime Warranty
on Jacuzzi Branded Baths for the Comfort, Comfort Plus,
Pure Air®, Luxury, SalonTM Spa, and Pure Air® II Collections
WARRANTY COVERAGE
Jacuzzi Whirlpool Bath (the “Company”) offers the following expressed limited lifetime warranty to the original purchaser of any Jacuzzi® Whirlpool Bath
products provided in the Company’s Comfort, Comfort Plus, Pure Air®, Pure Air® II, and Luxury™ collections ("Bath") who purchases the Bath for personal
or single family residential use (“user”): The Company will repair or replace, at its sole option, the Bath or its equipment in accordance with the following
terms and conditions. The warranty does not apply to non-branded Bath products manufactured by the Company.
LIFETIME WARRANTY ON BATHS
The Company extends to the user of the Bath a non-transferable limited lifetime warranty that the shell will maintain its structural integrity and conguration
and be free of water loss due to a defect in the tub shell. This warranty covers only the tub shell and the manufacturer installed pump, jets, controls, and
blower against defects in material or workmanship. This warranty does not apply to any display models or to any options or accessories which are covered
under our limited ninety (90) day warranty set forth below. Warranty coverage begins on the date the unit was originally purchased by the user and upon
receipt by the Company of a completely lled out Warranty Registration Card as described below.
2 YEAR LABOR WARRANTY FOR ALL FACTORY INSTALLED COMPONENTS:
Our limited labor warranty is for a period of Two (2) Years from the date the unit was originally purchased by the user, but not more than Three (3) Years
from date of manufacture. All factory installed components (e.g., pump, motor, blower, and plumbing) are covered under our labor warranty against failure
due to defects in materials and workmanship.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
Our limited warranty on options and accessories is for ninety (90) days for parts only. Our warranty covers options and accessories manufactured
(e.g., ll spout kits, trim kits, skirts, video monitors, plasma television screens, CD and MP3 players, and other music and video devices and optional
heaters) against defects in material or workmanship. Warranty coverage begins on the date the option or accessory was originally purchased by the
user. These items may be covered by a manufacturer’s warranty which may have a longer duration than this limited warranty. Please conrm with the
manufacturer the duration of the appropriate warranty for Options and Accessories.
WARRANTY LIMITATIONS
Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other persons, pets, or rodents, or resulting
from, without limitation, any of the following: careless handling (lifting unit by plumbing, abrading nish, etc.) including its own negligence; modication
of any type for any reason (including modication to meet local codes); improper installation (including installation not in accordance with instructions
and specications provided with the unit); connections supplied by the installer of the equipment; improper voltage supply or unauthorized electrical
modication; misuse; incorrect operation, or lack of proper routine maintenance; operation of the unit without specied minimum amount of water or at
inappropriate water temperature; use of abrasive or improper cleaners; or acts of God, such as lightning, oods, earthquakes, etc.
In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause
(e.g., water damage to carpet, ceiling, tiles, marble, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts
when pool and/or spa chemicals are used in the unit or hard water conditions; optional bath equipment not manufactured by the Company but supplied by
Dealer, installer or the Company; the unit's prior usage as an operational display; or defects that should have been discovered before installation.
This limited warranty does not include: labor, transportation, or other costs incurred in the removal and/or reinstallation of the original unit and/or installation
of a replacement unit; any costs relating to obtaining access for repair; or loss of use damage, including loss of sales, prot or business advantage of any
kind under any circumstances. Bath units are excluded from any warranty coverage if any addition, deletion, or modication of any kind whatsoever has
been made to the unit (or to any component). Warranty coverage is provided in the United States of America and Canada only.
EXCLUSION OF IMPLIED WARRANTIES
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO THE
FULLEST EXTENT ALLOWED BY LAW.
Jacuzzi Whirlpool Bath
14525 Monte Vista Avenue
Chino, California 91710
NOTICE: This warranty gives you specic legal rights, and you may also have other rights which vary from state to state. There are no warranties
applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not
be responsible for any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature
or specications furnished by the Company.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusions may not apply to you.
RETURN OF WARRANTY CARD
The attached Warranty Registration Card MUST be lled out by the purchaser within thirty (30) days from purchase and received by Jacuzzi Whirlpool Bath
in order for this warranty to become effective.
RESPONSIBILITIES OF OTHERS
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for
ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility.
In the event of a problem, the unit must not be installed. The Company is not responsible for failures or damage that could have been discovered,
repaired, or avoided by proper inspection and testing (including proper water testing) prior to installation. Damage occurring in transit is the responsibility
of the carrier. The user or installer MUST open the crate and inspect the unit for damage when it is delivered. If damage is discovered, it must be
reported immediately to the seller and the carrier in writing, and an inspection requested. Failure of the carrier to respond should be reported to the
seller and the carrier. Your freight claims should be led promptly thereafter.
It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs relating
to obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.
Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the
responsibility of the user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer except as provided above and shall not extend to or apply to
any replacement parts for the Options and accessories. Any replacement parts shall be covered by the original equipment manufacturer.
The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these requirements
at the time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state
building codes in U.S.A. or municipal or provincial codes in Canada.
WARRANTY SERVICE
For the customer's benet, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such rms are
not agents or representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type
covered by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of
the nature of the problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user
proving that the failure occurred or was discovered within the warranty period; an authorized independent service person or Company representative has
been permitted to inspect the unit during regular business hours within a reasonable time after the problem was reported by the user.
In order to obtain warranty service, contact the nearest Jacuzzi Whirlpool Bath Authorized Service Agent (http://www.jacuzzi.com/trade/bath_product_
support/repairs/) for listing. Describe the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service.
If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:
Jacuzzi Whirlpool Bath
Warranty Service Department
14525 Monte Vista Avenue
Chino, California 91710
Call: 1-(800) 288-4002
Limited Warranty
Accessory(ies)
Parts Only
On
To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and
Ninety-Day
supplied by the Company, call or write the above. Provide a description of the problem and proof of purchase. You will be instructed how
to obtain replacements and where to return, at your expense, the failed component(s), option(s), or accessory(ies).
All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the
tender terminates the Company's warranty obligation.
Limited Warranty
Accessory(ies)
Parts Only
Ninety-Day
On
Please note that the Registration Card may be completed on-line at Jacuzzi.com
( ) 1 day ( ) 2 months- 6 months
( ) 2-7 days ( ) 6 months- 1 year
( ) 1 week- 2 weeks ( ) 1 year- 2 years
( ) 2 weeks- 4 weeks ( ) +2 years
( ) 1 month- 2 months
10. Approximately how long have you lived in this home? _________________
11. Please indicate, approximately, the total annual income of your household.
( ) Up to $24,999 ( ) $50,000 to $74,999
( ) $25,000 to $29,999 ( ) $75,000 to $99,999
( ) $30,000 to $39,999 ( ) $100,000 to $149,999
( ) $40,000 to $49,999 ( ) $150,000 and Above
12. Was your purchase process?
( ) Very easy ( ) Easy ( ) Difcult ( ) Very Difcult
13. How technically aware were you of the patented Jacuzzi® jet system prior to
( ) Not aware ( ) Somewhat aware ( ) Very aware
your purchase?
JACUZZI WHIRLPOOL BATH
FL61000B
( ) Brand Name ( ) Price ( ) Hydrotherapy
( ) Home Resale _____________________________________________
( ) Other ___________________________________________________
4. Who nally decided which product you would buy?
( ) Self ( ) Spouse ( ) Self and Spouse Together
( ) Other Family Member ( ) Designer/Architect
( ) Builder/Plumber/Remodeler ( ) Already Installed
5. Who installed? ( ) Already installed/New Home
( ) Contractor/Plumber when remodeling
( ) Self/Spouse when remodeling
( ) Other ___________________________________________________
6. What is the current market value of this property?
Please estimate $ _____________________________________________
7. What is the age of the head of the household? __________________ years
8. What other manufacturers did you consider?
( ) Eljer ( ) Lasco ( ) Price Pster ( ) Aqua Glass
( ) Kohler ( ) American Standard ( ) Sterling
( ) Other (Specify) ____________________________________________
9. How long did you shop before purchasing unit?
Model Name ___________________________________________________
Serial Number __________________________________________________
Dealer's Name __________________________________________________
Dealer's Address ________________________________________________
1. How did you rst hear about this Jacuzzi® product?
( ) Advertisement ( ) Article in Magazine/Newspaper
( ) Visited Dealer/Plumbing Supplier ( ) Yellow Pages
( ) Builder/Plumber/Remodeler ( ) Decorator/Architect
( ) Visited Retailer/Home Center Store
( ) Word of Mouth . . . Friend/Relative/Acquaintance
( ) Other (Please Describe) _____________________________________
2. Who rst gave you specic information about this product (specications, prices,
( ) Dealer/Plumbing Supplier ( ) Builder ( ) Remodeler
( ) Plumbing Contractor ( ) Retailer/Home Center Store
( ) Decorator/Architect ( ) Already Installed
3. What was the main reason for purchase?
( ) Styling ( ) Warranty Service ( ) Product Features
etc.)?
City _________________________________ State _______ Zip _________
Date of Purchase ________________________________________________
This card must be lled out and returned to the address printed on the other side
within thirty (30) days from date of purchase in order for this warranty to be come
effective.
Purchaser's Name _______________________________________________
Purchaser's Address _____________________________________________
Warranty
Registration Card
Loading...