Jacuzzi EV77959 User Manual

Refresh
Personal Hygiene System™

OWNER’S MANUAL

Round EU44959 — ROUND FRONT
Elongated EV77959 — ELONGATED FRONT

This manual contains important safety information.

Please read carefully before product installation or use.

EX93000 Refresh Installation Manual 10/06

Important Safeguards

CAUTION CAUTION

For safety reasons, please read this entire manual before installation or use.

Danger - Possibility of electric shock!

Use the correct voltage according to the specifications and
connect to a three-prong GFCI grounded outlet.

NOTE: This GFCI outlet
should be installed
prior to performing
this installation.

Please use caution and avoid spraying water directly on the
Refresh Personal Hygiene System™ or power cord. This could
result in electric
shock or fire.

Specifications

Model

Rated Power Source

Tap Water Pressure

Rated Power Consumption

Seat Temperature

EU44959 — ROUND FRONT

OFF: room temperature LOW: 97°F (35°C) MED: 100°F (38°C) HIGH: 104°F (40°C)

Do not use harsh brushes or abrasive detergents to clean
the Refresh Personal Hygiene System™. Use only mild soap
and a soft cloth
for cleaning.

Do not disassemble or modify the Refresh Personal Hygiene
System™. Only a authorized service representative should
perform repairs.

EV77959 — ELONGATED FRONT

120VAC , 15 Amp GFCI (1400W)

7–106 psi (0.5-7.5 kgf/cm)

1.5 kwh

Seat & Lid

Maximum Spray Volume

Water Temperature

Dryer Temperature

Electrical Safety Protection

Power Cord Length

Product Dimensions

Product Weight

Parts & Configuration

Refresh

Remote Control,
Mount Kit, Batteries

Soft Closing

0.2 gal/min (0.72 liter/min)

OFF: room temperature LOW: 97°F (35°C) MED: 100°F (38°C) HIGH: 104°F (40°C)

LOW / MED / HIGH

15mA – GFCI

4 ft (1.2m)

(383 mm W x 483 mm L x 153 mm H)

15"W x 19"L x 6"H

9.5 lbs (4.3 kg)

Filter

T-Valve with

Filter and Bidet Hose

Mounting plate

Installed
Configuration

Supply Line

15"W x 20.1"L x 6"H
(383 mm W x 511 mm L x 153 mm H)

9.7 lbs (4.4 kg)

GFCI

grounded

outlet

T-Valve

Water

Remote

Control

Remote

Mount

Front Nozzle

Back Nozzle

Heated Seat

Standard Mounting

Hardware

Alternate Mounting

Hardware

EX93000 Refresh Installation Manual 10/06

Universal Wrench

1

Water

Shut-Off

Valve

Bidet Hose

Typical install time: 30-60 minutes

Before Installation

Tools Needed

• Flat head screwdriver • Universal wrench (included)

• Phillips head screwdriver • Measuring tape

NOTE: The included Universal Wrench will work for most applications. Depending on your toilet
confi guration, an adjustable wrench may also be needed.

Alternate Mounting Hardware

Some toilets may not provide adequate access to the seat mounting holes preventing proper
installation of the Standard Mounting Hardware.

In this case you will need to use the Alternate Mounting Hardware and follow the enclosed instructions.

Check Water Supply Line

Check the line that connects the toilet tank to the water shut-off valve. If it is rigid pipe, you may need
to purchase a flexible hose to replace it before installing the Refresh Personal Hygiene System™. The
length of the hose and the size of the connectors will vary.

Installation

CAUTION CAUTION

Please read these carefully before installing the Refresh Personal Hygiene System™.

Failure to do so could result in flooding, leaking, or damage to the Refresh Personal Hygiene System™.

1) Remove Toilet Seat

Steps may vary by type of seat.

a) Lift hinge covers and use a screwdriver to

remove the mounting bolts.

b) Remove the toilet seat.

1a

2) Turn OFF Water and Flush Toilet

You may wish to place a container under the
tank to catch any leaking that could occur
during installation.

a) Turn water valve OFF completely. If the water valve

does not shut OFF completely, STOP. Repair the

water shut-off valve before proceeding.
b) Flush the toilet to empty the tank.
c) Disconnect water supply line from toilet tank.

IMPORTANT: Do not continue without completing these
steps! Failure to do so could result in flooding, leaking, or
damage to the Refresh Personal Hygiene System™.

3) Install Mounting Plate

NOTE: These instructions are for Standard Mounting Hardware. See
Alternate Mounting Hardware at the top of this page for further details.

1b

2b

2a

2c

3b

3a

a) Place Mounting Plate over mounting holes, flat side down,

curve toward the back of the toilet.
b) Insert bolts through the Mounting Plate and finger

tighten the wing nuts. Make sure the crush washer and

metal flat washer are put on in the correct order (see

graphic).

Crush Washer

Metal Flat Washer

2

Mounting Holes

EX93000 Refresh Installation Manual 10/06