Jacuzzi CETRA WITH INTEGRAL SKIRT, AMIGA, CETRA 532, CETRA 536, CETRA 536 WITH INTEGRAL SKIRT Installation And Operating Instructions Manual

BUILDER/COMFORT BATH SERIES

ELECTRONIC & MANUAL CONTROLS

INSTALLATION AND OPERATING INSTRUCTIONS

Save These Instructions for Future Use.

Owner's Record

Date Purchased ____________________________________________________________

Purchased From ____________________________________________________________

Installed By ________________________________________________________________

Serial Number _____________________________________________________________

Model_____________________________________________________________________

Installer: Leave this manual for homeowner.

Homeowner: Read this manual and keep for future reference.

©

2005 Jacuzzi Whirlpool Bath K272000AF 7/06

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

ENGLISH

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS

WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:

DANGER — TO REDUCE THE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS UNIT

UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES.
WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL. DO

NOT USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURER.

WARNING — NEVER DROP OR INSERT ANY OBJECT INTO ANY OPENING.
WARNING — DO NOT OPERATE THIS UNIT WITHOUT THE GUARD OVER THE SUCTION FITTING.
WARNING — THIS UNIT MUST BE CONNECTED ONLY TO A SUPPLY CIRCUIT THAT IS PROTECTED

BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI). SUCH A GFCI SHOULD BE PROVIDED BY
THE INSTALLER AND SHOULD BE TESTED ON A ROUTINE BASIS. TO TEST THE GFCI, PUSH THE
TEST BUTTON. THE GFCI SHOULD INTERRUPT POWER. PUSH THE RESET BUTTON. POWER
SHOULD BE RESTORED. IF THE GFCI FAILS TO OPERATE IN THIS MANNER, THE GFCI IS
DEFECTIVE. IF THE GFCI INTERRUPTS POWER TO THE BATHTUB WITHOUT THE TEST BUTTON
BEING PUSHED, A GROUND CURRENT FLOWING, INDICATING A POSSIBILITY OF AN ELECTRIC
SHOCK. DO NOT USE THIS HYDROMASSAGE BATHTUB. DISCONNECT THE HYDROMASSAGE
BATHTUB AND HAVE THE PROBLEM CORRECTED BY A QUALIFIED SERVICE REPRESENTATIVE
BEFORE USING.
WARNING — (FOR PERMANENTLY CONNECTED UNITS) A GREEN COLORED TERMINAL (OR A WIRE
CONNECTOR MARKED “G”, “GR”, “GROUND”, OR “GROUNDING”) IS PROVIDED WITHIN THE TERMINAL
COMPARTMENT. TO REDUCE THE RISK OF ELECTRIC SHOCK, CONNECT THE TERMINAL OR
CONNECTOR TO THE GROUNDING TERMINAL OF YOUR ELECTRIC SERVICE OR SUPPLY PANEL WITH
A CONDUCTOR EQUIVALENT IN SIZE TO THE CIRCUIT CONDUCTORS SUPPLYING THIS EQUIPMENT.

OPERATING INSTRUCTIONS

WARNING — PROLONGED IMMERSION IN HOT WATER MAY INDUCE HYPERTHERMIA. HYPER-

THERMIA OCCURS WHEN THE INTERNAL TEMPERATURE OF THE BODY REACHES A LEVEL SEV­ERAL DEGREES ABOVE THE NORMAL BODY TEMPERATURE OF 98.6°F. THE SYMPTOMS OF
HYPERTHERMIA INCLUDE AN INCREASE IN THE INTERNAL TEMPERATURE OF THE BODY, DIZZI­NESS, LETHARGY, DROWSINESS AND FAINTING. THE EFFECTS OF HYPERTHERMIA INCLUDE:

A) FAILURE TO PERCEIVE HEAT
B) FAILURE TO RECOGNIZE THE NEED TO EXIT THE SPA OR HOT TUB,
C) UNAWARENESS OF IMPENDING HAZARD,
D) FETAL DAMAGE IN PREGNANT WOMEN,
E) PHYSICAL INABILITY TO EXIT THE SPA OR HOT TUB, AND
F) UNCONSCIOUSNESS RESULTING IN DANGER OF DROWNING.

WARNING — THE USE OF ALCOHOL, DRUGS OR MEDICATION CAN GREATLY INCREASE THE
RISK OF FATAL HYPERTHERMIA.
WARNING — DO NOT TAMPER WITH USER-OPERATED CONTROLS OR SUCH DEVICES.

Jacuzzi Whirlpool Bath K272000AF 7/06

2

INSTALLATION INSTRUCTIONS

WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
DANGER — RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND

FAULT CIRCUIT INTERRUPTER (GFCI).
CAUTION — TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE
PERIODICALLY IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS.
WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL. DO NOT
USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURERS.

WARNING — TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE BATHTUB.
WARNING — KEEP BODY AND HAIR A MINIMUM OF 6" AWAY FROM SUCTION FITTING AT ALL TIMES

WHEN THE HYDROMASSAGE SYSTEM IS OPERATING. HAIR LONGER THAN SHOULDER LENGTH
SHOULD BE SECURED CLOSE TO THE HEAD.
WARNING — RISK OF ELECTRICAL SHOCK; DO NOT PERMIT ELECTRICAL APPLIANCES (SUCH AS HAIR DRYER,
LAMP, TELEPHONE, RADIO OR TELEVISION) WITHIN 60" (1.5 M) OF THIS HYDROMASSAGE BATHTUB.
WARNING — RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE DRUGS OR ALCOHOL
BEFORE OR DURING THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID
UNCONSCIOUSNESS AND POSSIBLE DROWNING.
WARNING — RISK OF FETAL INJURY; PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD
CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.
WARNING — RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; DO NOT USE A HYDROMASSAGE
BATHTUB EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.
WARNING — RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; WATER TEMPERATURE IN EXCESS
OF 104°F (40°C) MAY BE INJURIOUS TO YOUR HEALTH. CHECK AND ADJUST WATER TEMPERATURE
BEFORE USE.
WARNING — RISK OF HYPERTHERMIA; PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB
EQUIPPED WITH A HEATER.

ENGLISH

FOR BUILT-IN AND DROP-IN UNITS, INSTALL TO PERMIT ACCESS FOR SERVICING.
THIS UNIT SHOULD BE ELECTRICALLY GROUNDED AND INSTALLED BY A LICENSED CONTRACTOR,

ELECTRICIAN, AND PLUMBER.

BUILDING MATERIALS AND WIRING SHOULD BE ROUTED AWAY FROM THE MOTOR/PUMP OR

BLOWER OR OTHER HEAT PRODUCING COMPONENTS OF THIS UNIT.

A PRESSURE WIRE CONNECTOR IS PROVIDED ON THE EXTERIOR OF THE MOTOR/PUMP AND
HEATER TO PERMIT CONNECTION OF AN NO. 8 AWG (8.4 MM) SOLID COPPER BONDING CONDUCTOR
BETWEEN THIS UNIT AND ALL OTHER ELECTRIC EQUIPMENT AND EXPOSED METAL IN THE VICINITY,
AS NEEDED TO COMPLY WITH LOCAL REQUIREMENTS.

PRECAUTIONS

••

•

Do not operate the hydromassage system unless the bath is filled with water to at least 1" to 2" (2,5 - 5,08 cm) above the

••

highest jet.

••

•

Do not immerse the control panel by overfilling the bath.

••

••

•

Do not use oil-based bath additives in your hydromassage bath.

••

••

• When cleaning your bath, do not use abrasive substances which will damage the bath's surface.

••

••

•

To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).

••

NOTE: This is a professional grade product. A knowledge of construction techniques, plumbing and electri­cal installation according to codes are required for proper installation and user satisfaction. We recommend
that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does
not cover improper installation related problems.

PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.

The Company has obtained applicable code (standards) listings generally available on a national basis for products of this type.
It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. The
Company makes no representation or warranty regarding, and will not be responsible for any code compliance.

3

Jacuzzi Whirlpool Bath K272000AF 7/06

CONTENTS

Safety Instructions _____________________________________________________________________ 2-3

Contents _____________________________________________________________________________ 4

ENGLISH

Specifications _________________________________________________________________________ 5-9

Roughing-in __________________________________________________________________________ 10-17

Cutout ______________________________________________________________________________ 17

Installation Instructions __________________________________________________________________ 18-24

Framing and Support _________________________________________________________________ 18

Skirts ______________________________________________________________________________ 19

Service Access _____________________________________________________________________ 20

Electrical Connections ________________________________________________________________ 21

Plumbing and Water Supply ___________________________________________________________ 22

Undermount Installation Instructions _____________________________________________________ 23-24

Operation ____________________________________________________________________________ 25-26

Maintenance __________________________________________________________________________ 27

General Troubleshooting Guide ___________________________________________________________ 28

Authorized Service _____________________________________________________________________ 30

Warranty _____________________________________________________________________________ 31-32

NOTE: If you need a referral for a service company near you, or need assistance with operation or maintenance
related questions, please call our USA Service Support Department at 1-800-288-4002. Visit our web site at http:/
/www.jacuzzi.com/ for products and services.
To find service agent listings for:

Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF

Jacuzzi Whirlpool Bath K272000AF 7/06

4

L

1"

(25 mm)

H

W

SIDE VIEW

BATHS WITH INTEGRAL SKIRT

END VIEW

SPECIFICATIONS

Important: Read complete instructions before beginning installation.

Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings
necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the bath.

Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do

not lift the bath by the plumbing at any time; handle by the shell only.

Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do
not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi
Whirlpool Bath responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any
claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty informa­tion packed with the product.

All bath units are factory tested for proper operation and watertight connections prior to shipping. NOTE: Prior to installa-

tion, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage
or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or

avoided by following this inspection and testing procedure.

Not all tubs shown may be available as export units. Export tubs come with MANUAL controls and may come:

• with Pump/motor packaged

• with Pump/motor installed,

• with NO overflow cutout.

Because of the variety of export tub types some instructions may not apply to your unit. Disregard instructions that do not
apply to your specific tub.

RECTANGULAR BATHS

L

(51 mm)

separately,

W

2"

H

ENGLISH

SIDE VIEW

BATHS WITHOUT INTEGRAL SKIRT

L

SIDE VIEW

(25 mm)

1"

BATHS WITH 3-SIDED TILE FLANGE

SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand

MODEL

AMIGA™

LH & RH

AMIGA™
WITH INTEGRAL
SKIRT

LH & RH

©

BIANCA

LH

©

CETRA
WITH INTEGRAL
SKIRT
LH & RH

©

CETRA

532

LH & RH

CETRA© 536

LH & RH

DIMENSIONS

72" (1829 mm) L*
36" ( 914 mm) W

20-3/4" ( 533 mm) H

72" (1829 mm) L
36" ( 914 mm) W

20-3/4" ( 533 mm) H

72" (1829 mm) L*
48" (1219 mm) W

20-1/2" ( 521 mm) H

60" (1524 mm) L
32" ( 813 mm) W

20-1/2" ( 521 mm) H

60" (1524 mm) L*
31-7/8" ( 791 mm) W

21-1/4" ( 553 mm) H

60" (1524 mm) L
36" ( 914 mm) W

21-1/4" ( 553 mm) H

*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.

NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.

(Optional) RapidHeat

TM

: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.

Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.

DRAIN/OVERFLOW

16-7/8" (429 mm) A
14" (356 mm) B

16-7/8" (429 mm) A

*

14" (356 mm) B

16" (406 mm) A
8-1/2" (216 mm) B

17-7/8" (454 mm) A

*

9-3/8" (238 mm) B

18-1/2" ( 470 mm) A
9" ( 229 mm) B

18-1/2" ( 470 mm) A

*

9" ( 229 mm) B

END VIEW

H

DIMENSIONS

W

END VIEW

CUTOUT

70" x 34"

(1778 mm x

864 mm)

70" x 46"

(1778 mm x

1168 mm)

58" x 30-1/4"

(1473 mm x

768 mm)

58" x 34-1/4"

(1473 mm x

870 mm)

NA

NA

TOTAL WEIGHT/

FLOOR LOADING

772 lb

(351 kg)/

2

43 lb/ft

(210 kg/m2)

796 lb

(362 kg)/

2

44 lb/ft

(214 kg/m2)

993 lb

(451 kg)/

2

41 lb/ft

(200 kg/m2)

727 lb

(330 kg)/

2

55 lb/ft

(268 kg/m2)

697 lb

(317 kg)/

2

53 lb/ft

(259 kg/m2)

742 lb

(337 kg)/

2

50 lb/ft

(244 kg/m2)

5

OPERATING

GALLONAGE

50 U.S. gal

(186 liters)

50 U.S. gal

(186 liters)

73 U.S. gal

(276 liters)

46 U.S. gal

(174 liters)

43 U.S. gal

(163 liters)

48 U.S. gal

(181 liters)

A

B

DRAIN/OVERFLOW

HEATER READY

PRODUCT

WEIGHT

105 lb

(48 kg)

129 lb

(59 kg)

135 lb

(61 kg)

94 lb

(43 kg)

89 lb

(41 kg)

92 lb

(42 kg)

SKIRT &

MOUNTING

Optional,
U-Frame

Integral

Optional,
U-Frame

Integral

Optional

U-Frame

Optional

U-Frame

FOR FIELD

INSTALLATION

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Jacuzzi Whirlpool Bath K272000AF 7/06

SPECIFICATIONS

SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand

HEATER READY

PRODUCT

WEIGHT

92 lb

(42 kg)

80 lb

(36 kg)

100 lb

(45 kg)

90 lb

(41 kg)

95 lb

(43 kg)

95 lb

(43 kg)

104 lb

(47 kg)

114 lb

(52 kg)

100 lb

(45 kg)

110 lb

(50 kg)

97 lb

(44 kg)

SKIRT &

MOUNTING

IntegralNA

Optional,
U-Frame

Integral

Optional,
U-Frame

Integral

Not

Available

Not

Available

Integral

Optional,
U-Frame

Not

Available

Optional,
U-Frame

2

2

2

2

2

2

2

2

2

2

2

OPERATING

GALLONAGE

48 U.S. gal

(181 liters)

44 U.S. gal

(167 liters)

42 U.S. gal

(159 liters)

58 U.S. gal
(220 liters)

38 U.S. gal

(144 liters)

46 U.S. gal

(172 liters)

70 U.S. gal

(265 liters)

70 U.S. gal

(265 liters)

62 U.S. gal

(235 liters)

76 U.S. gal

(288 liters)

46 U.S. gal
(170 liters)

NA

NA

NALUXURA™ 530

NA

TOTAL WEIGHT/

FLOOR LOADING

742 lb

(337 kg)/

50 lb/ft

(244 kg/m2)

697 lb

(264 kg)/

52 lb/ft

(254 kg/m2)

700 lb

(318 kg)/

53 lb/ft

(259 kg/m2)

823 lb

(374 kg)/

53 lb/ft

(259 kg/m2)

662 lb

(301 kg)/

53 lb/ft

(259 kg/m2)

728 lb

(331 kg)/

42 lb/ft

(205 kg/m2)

937 lb

(423 kg)/

44 lb/ft

(215 kg/m2)

947 lb

(430 kg)/

45 lb/ft

(220 kg/m2)

866 lb

(394 kg)/

50 lb/ft

(244 kg/m2)

993 lb

(451 kg)/

47 lb/ft

(229 kg/m2)

722 lb

(328 kg)/

41 lb/ft

(200 kg/m2)

MODEL

CETRA© 536
WITH INTEGRAL
SKIRT

ENGLISH

LH & RH

LUXURA™ 5
WITH INTEGRAL
3-SIDED TILE
FLANGE
LH & RH

LUXURA™ 5
WITH INTEGRAL
SKIRT
LH & RH

LUXURA™ 5.5

LH & RH

WITH INTEGRAL
SKIRT
LH & RH

MAJORA© 5

LH & RH

MAJORA© 6

LH & RH

©

6

MAJORA
WITH INTEGRAL
SKIRT
LH & RH

©

5

MITO

LH & RH

MITO© 6

LH & RH

©

5

NOVA

LH & RH

DIMENSIONS

60" (1524 mm) L*
36" ( 914 mm) W

21-1/4" ( 553 mm) H

60" (1524 mm) L
32" ( 813 mm) W

20-1/4" ( 514 mm) H

60" (1524 mm) L
32" ( 813 mm) W
20-1/4" ( 514 mm) H

66" (1676 mm) L
34" ( 864 mm) W

20" ( 508 mm) H

60" (1524 mm) L*
30" ( 762 mm) W

20-1/4" ( 483 mm) H

60" (1524 mm) L*
42" (1067 mm) W

19-1/2" ( 495 mm) H

72" (1829 mm) L*
42" (1067 mm) W

19-3/4" ( 502 mm) H

72" (1829 mm) L
42" (1067 mm) W

19-3/4" ( 502 mm) H

60" (1524 mm) L
42" (1067 mm) W

21" ( 533 mm) H

72" (1829 mm) L*
42" (1067 mm) W

21-1/2" ( 546 mm) H

60" (1524 mm) L
42" (1067 mm) W

18-1/2" ( 470 mm) H

DRAIN/OVERFLOW

DIMENSIONS

18-1/2" ( 470 mm) A
9" ( 229 mm) B

*

15-1/4" (387 mm) A
8-1/4" (210 mm) B

15-1/4" (387 mm) A
8-1/4" (210 mm) B

*

15-1/4" (387 mm) A
8-3/8" (213 mm) B

16-3/4" (425 mm) A
9-1/4" (235 mm) B

15" (381 mm) A
8-3/4" (222 mm) B

15-5/8" (397 mm) A
10-1/2" (267 mm) B

15-5/8" (397 mm) A

*

10-1/2" (267 mm) B

17-1/2" (445 mm) A

*

11-7/8" (302 mm) B

17-1/2" (445 mm) A
11-7/8" (302 mm) B

14-3/4" (375 mm) A

*

8-1/2" (216 mm) B

CUTOUT

Molded-in

Tile Flange

64" x 32"

(1626 mm x

813 mm)

58" x 40"

(1473 mm x

1016 mm)

70" x 40"

(1778 mm x

1016 mm)

58" x 40"

(1473 mm x

1016 mm)

70" x 40"

(1778 mm x

1016 mm)

58" x 40"

(1473 mm x

1016 mm)

FOR FIELD

INSTALLATION

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(U395000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.

NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.

(Optional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.

Jacuzzi Whirlpool Bath K272000AF 7/06

6

SPECIFICATIONS

SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand

MODEL

©

5

NOVA
WITH INTEGRAL
3-SIDED TILE
FLANGE
LH & RH

©

NOVA

5
WITH INTEGRAL
SKIRT
LH & RH

©

6

NOVA

LH & RH

©

NOVA

536

LH & RH

©

536

NOVA
WITH INTEGRAL
SKIRT
LH & RH

©

636

NOVA
WITH INTEGRAL
SKIRT
LH & RH

©

SIGNA

5

LH & RH

©

5 WITH

SIGNA
INTEGRAL SKIRT,
FRONT RIGHT
MOTOR/PUMP
LH & RH

SIGNA© 5
WITH INTEGRAL
3-SIDED TILE
FLANGE
RH

SIGNA© 6

LH & RH

DIMENSIONS

60" (1524 mm) L*
42" (1067 mm) W

18-1/2" ( 470 mm) H

60" (1524 mm) L*
42" (1067 mm) W

18-1/2" ( 470 mm) H

72" (1829 mm) L
42" (1067 mm) W

20-1/2" ( 521 mm) H

60" (1524 mm) L
36" ( 914 mm) W

19-1/4" ( 489 mm) H

60" (1524 mm) L*
36" ( 914 mm) W

19-1/4" ( 489 mm) H

72" (1829 mm) L
36" ( 914 mm) W

19" ( 483 mm) H

60" (1524 mm) L*
42" (1067 mm) W

22" ( 559 mm) H

60" (1524 mm) L
42" (1067 mm) W

22" ( 559 mm) H

60" (1524 mm) L
42" (1067 mm) W

22" ( 559 mm) H

72" (1829 mm) L*
42" (1067 mm) W

22" ( 559 mm) H

DRAIN/OVERFLOW

DIMENSIONS

14-3/4" (375 mm) A
8-1/2" (216 mm) B

15-7/8" (403 mm) A
9-1/4" (235 mm) B

14-3/4" (375 mm) A

*

8-1/2" (216 mm) B

15-1/8" (384 mm) A

*

9" (229 mm) B

14-5/8" (372 mm) A
9" (229 mm) B

14-5/8" (372 mm) A

*

9-3/8" (238 mm) B

17-1/2" (445 mm) A
12-1/2" (318 mm) B

17-7/8" (451 mm) A

*

12-3/4" (330 mm) B

*

17-1/2" (445 mm) A
12-1/2" (318 mm) B

16-7/8" (429 mm) A
14" (356 mm) B

TOTAL WEIGHT/

CUTOUT

Molded-in

Tile Flange

70" x 40"

(1778 mm x

1016 mm)

58" x 34"

(1473 mm x

863 mm)

58" x 40"

(1473 mm x

1016 mm)

70" x 40"

(1778 mm x

1016 mm)

FLOOR LOADING

NA

NA

NA

NA

NA Yes

NA

722 lb

(328 kg)/

41 lb/ft

(200 kg/m2)

737 lb

(335 kg)/

42 lb/ft

(205 kg/m2)

876 lb

(398 kg)/

42 lb/ft

(205 kg/m2)

683 lb

(310 kg)/

46 lb/ft

(224 kg/m2)

698 lb

(317 kg)/

47 lb/ft

(229 kg/m2)

824 lb

(375 kg)/

45.8 lb/ft

(223 kg/m2)

708 lb

(321 kg)/

40 lb/ft

(195 kg/m2)

723 lb

(329 kg)/

41 lb/ft

(200 kg/m2)

708 lb

(321 kg)/

40 lb/ft

(195 kg/m2)

826 lb

(375 kg)/

39 lb/ft

(190 kg/m2)

2

2

2

2

2

2

2

2

2

2

OPERATING

GALLONAGE

46 U.S. gal

(174 liters)

45 U.S. gal

(174 liters)

62 U.S. gal
(235 liters)

42 U.S. gal

(159 liters)

42 U.S. gal
(159 liters)

56 U.S. gal
(223 liters)

42 U.S. gal
(159 liters)

42 U.S. gal

(159 liters)

42 U.S. gal

(159 liters)

55 U.S. gal

(208 liters)

PRODUCT

WEIGHT

97 lb

(44 kg)

112 lb

(51 kg)

110 lb

(50 kg)

83 lb

(38 kg)

98 lb

(45 kg)

108 lb

(49 kg)

108 lb

(49 kg)

123 lb

(56 kg)

108 lb

(49 kg)

118 lb

(54 kg)

SKIRT &

MOUNTING

Not

Available

Integral

Optional,
U-Frame

Not

Available

Integral

Integral

Optional,
U-Frame

Integral

Optional,
U-Frame

Not

Available

HEATER READY

(S750000 HEATER KIT)

(S750000 HEATER KIT)

(S750000 HEATER KIT)

(S750000 HEATER KIT)

(S750000 HEATER KIT)

(S750000 HEATER KIT)

(U395000 HEATER KIT)

(S750000 HEATER KIT)

(S750000 HEATER KIT)

FOR FIELD

INSTALLATION

Yes

No

Yes

Yes

Yes

Yes

Yes

Yes

Yes

ENGLISH

*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.

NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.

(Optional) RapidHeat

TM

: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.

Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.

7

Jacuzzi Whirlpool Bath K272000AF 7/06

RIMLESS OVAL BATHS

DRAIN/OVERFLOW

A

B

END VIEW

H

W

SIDE VIEW

L

2"

(51 mm)

LUNA

SPECIFICATIONS

END VIEW

W

W

3-1/2"

(89 mm)

L

2'' (51 mm)

SIDE VIEW

8"

(203 mm)

W

H

END VIEW

MILANO

2''

(51 mm)

L

7-1/2"

H

ENGLISH

(191 mm)

2"

(51 mm)

SIDE VIEW

FRESCO

L

H

SIDE VIEW

GALLERY 5 OVAL & GALLERY 6 OVAL

RIVA 5 & RIVA 6

END VIEW

SPECIFICATIONS (Oval) LH = Left Hand, RH = Right Hand

HEATER READY

FOR FIELD

INSTALLATION

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

Yes

(S750000 HEATER KIT)

MODEL

©

FRESCO

LH & RH

GALLERY™ 5
OVAL

LH & RH

GALLERY™ 6
OVAL

LH & RH

GALLERY™ 6
OVAL

UNDERMOUNT

LH & RH

LUNA™

RH

MILANO™

LH & RH

OPALIA™

LH & RH

©

5

RIVA

LH & RH

RIVA© 6

LH & RH

DIMENSIONS

71-1/2" (1816 mm) L
42" (1067 mm) W
27-1/4" ( 692 mm) H*

62" (1575 mm) L
43" (1092 mm) W
19" ( 483 mm) H

72" (1829 mm) L
42" (1067 mm) W
20-1/2" ( 521 mm) H

72" (1829 mm) L
42" (1067 mm) W
20-1/2" ( 521 mm) H

72" (1829 mm) L
42" (1067 mm) W
23" ( 584 mm) H

72" (1829 mm) L
40" (1016 mm) W
20-3/4" ( 527 mm) H

72" (1829 mm) L
44" (1118 mm) W
22-1/4" ( 565 mm) H

62" (1575 mm) L
43" (1092 mm) W
19" ( 483 mm) H

72" (1829 mm) L
42" (1067 mm) W
20-1/2" ( 521 mm) H

DRAIN/OVERFLOW

DIMENSIONS

20-1/8" (511 mm) A
11-3/4" (299 mm) B

14-3/4" (375 mm) A
9-1/2" (241 mm) B

16" (406 mm) A
11-1/2" (292 mm) B

16" (406 mm) A
11-1/2" (292 mm) B

19-1/8" (486 mm) A
11" (279 mm) B

18-1/2" (470 mm) A
11" (279 mm) B

18-3/4" (476 mm) A
12" (305 mm) B

14-3/4" (375 mm) A
9-1/2" (241 mm) B

16" (406 mm) A
11-1/2" (292 mm) B

CUTOUT

Template
Provided

P/N

P188000

Template
Provided

P/N

P186000

Template

Provided

P/N

P186000

Template

Provided

P/N

X302000

Template
Provided

P/N

P819000

Template

Provided

P/N

P188000

Template

Provided

P/N

P186000

Template

Provided

P/N

P186000

Template

Provided

P/N

P186000

TOTAL WEIGHT/
FLOOR LOADING

921 lb

(419 kg)/

2

44 lb/ft

(220 kg/m2)

746 lb

(339 kg)/

2

40 lb/ft

(195 kg/m2)

871 lb

(395 kg)/

2

42 lb/ft

(205 kg/m2)

871 lb

(395 kg)/

2

42 lb/ft

(205 kg/m2)

1221 lb

(555 kg)/

2

58 lb/ft

(283 kg/m2)

893 lb

(406 kg)/

2

45 lb/ft

(220 kg/m2)

978 lb

(445 kg)/

2

45 lb/ft

(220 kg/m2)

746 lb

(339 kg)/

2

40 lb/ft

(195 kg/m2)

871 lb

(396 kg)/

2

42 lb/ft

(205 kg/m2)

OPERATING

GALLONAGE

63 U.S. gal

(239 liters)

48 U.S. gal

(182 liters)

62 U.S. gal
(235 liters)

62 U.S. gal
(235 liters)

96 U.S. gal
(364 liters)

60 U.S. gal

(227 liters)

70 U.S. gal
(265 liters)

48 U.S. gal
(182 liters)

62 U.S. gal
(235 liters)

PRODUCT

WEIGHT

146 lb

(66 kg)

96 lb

(44 kg)

105 lb

(48 kg)

105 lb

(48 kg)

121 lb

(55 kg)

143 lb

(65 kg)

145 lb

(66 kg)

96 lb

(44 kg)

105 lb

(48 kg)

SKIRT &

MOUNTING

Not

Available

Not

Available

Not

Available

Not

Available

Not

Available

Not

Available

Not

Available

Not

Available

Not

Available

* For Fresco™ models H551, H549, and H550 this height is 23-3/4"

NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.

(Optional) RapidHeat
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.

Jacuzzi Whirlpool Bath K272000AF 7/06

TM

: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.

8

CORNER BATHS

SPECIFICATIONS

2"

(51 mm)

DRAIN/OVERFLOW

SIDE VIEW

H

END VIEW

CORNER BATH

1"

(25 mm)

H

FRONT VIEW

CAPELLA 55, CAPELLA 60, & TARA WITH INTEGRAL SKIRT

H

FRONT VIEW

CAPELLA SPACESAVER WITH INTEGRAL SKIRT

SIDE VIEW

1"
(25 mm)

SPECIFICATIONS (Corner) LH = Left Hand, RH = Right Hand

MODEL

©

CAPELLA

RH

CAPELLA
WITH INTEGRAL
SKIRT RH

CAPELLA
SPACESAVER
WITH INTEGRAL
SKIRT RH

CAPELLA
FRONT LEFT
MOTOR/PUMP
LH

CAPELLA© 60

LH & RH

CAPELLA
WITH INTEGRAL
SKIRT RH

GALLERY™
CORNER

LH & RH

TARA™

LH & RH

TARA™
WITH INTEGRAL
SKIRT RH

55

©

55

©

©

60

©

60

DIMENSIONS

55" (1397 mm) L
55" (1397 mm) L
20-1/4" ( 514 mm) H

55" (1397 mm) L
55" (1397 mm) L
20-1/2" ( 521 mm) H

60" (1524 mm) L
60" (1524 mm) L
20-1/2" ( 521 mm) H

60" (1524 mm) L
60" (1524 mm) L
20-1/2" ( 521 mm) H

60" (1524 mm) L
60" (1524 mm) L
20-1/2" ( 521 mm) H

60" (1524 mm) L
60" (1524 mm) L
20-1/2" ( 521 mm) H

60" (1524 mm) L
60" (1524 mm) L
22-1/2" ( 572 mm) H

60" (1524 mm) L
60" (1524 mm) L
20-3/4" ( 527 mm) H

60" (1524 mm) L
60" (1524 mm) L
20-3/4" ( 527 mm) H

DRAIN/OVERFLOW

DIMENSIONS

17-1/2" (445 mm) A
9-5/8" (245 mm) B

18" (457 mm) A
12-1/8" (308 mm) B

18" (457 mm) A
12-3/8" (308 mm) B

18" (457 mm) A
12-1/8" (308 mm) B

18" (457 mm) A
12-1/8" (308 mm) B

18" (457 mm) A
12-1/8" (308 mm) B

18-1/8" (451 mm) A
12" (305 mm) B

16" (406 mm) A
12-3/8" (314 mm) B

16" (406 mm) A
12-3/8" (314 mm) B

CUTOUT

Template

Provided

P/N

DA24000

NA

NA

See

Page 17

See

Page 17

NA

See

Page 17

See

Page 17

NA

TOTAL WEIGHT/
FLOOR LOADING

791 lb

(360 kg)/

2

38 lb/ft

(185 kg/m2)

1025 lb

(466 kg)/

2

48.8 lb/ft

(238 kg/m2)

880 lb

(400 kg)/

2

35 lb/ft

(171 kg/m2)

870 lb

(395 kg)/

2

35 lb/ft

(171 kg/m2)

870 lb

(395 kg)/

2

35 lb/ft

(171 kg/m2)

880 lb

(400 kg)/

2

35 lb/ft

(171 kg/m2)

984 lb

(447 kg)/

2

39 lb/ft

(244 kg/m2)

984 lb

(447 kg)/

2

39 lb/ft

(190 kg/m2)

999 lb

(454 kg)/

2

40 lb/ft

(195 kg/m2)

OPERATING

GALLONAGE

51 U.S. gal

(193 liters)

54 U.S. gal

(204 liters)

60 U.S. gal

(227 liters)

60 U.S. gal

(227 liters)

60 U.S. gal

(227 liters)

60 U.S. gal

(227 liters)

74 U.S. gal
(280 liters)

74 U.S. gal

(280 liters)

74 U.S. gal

(280 liters)

PRODUCT

WEIGHT

116 lb

(53 kg)

125 lb

(57 kg)

130 lb

(59 kg)

120 lb

(54 kg)

120 lb

(54 kg)

130 lb

(59 kg)

118 lb

(54 kg)

118 lb

(54 kg)

133 lb

(61 kg)

NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.

(Optional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.

SKIRT &

MOUNTING

Optional

Integral

Integral

Not

Available

Not

Available

Integral

Not

Available

Optional

Integral

A

B

SIDE VIEW

(S750000 HEATER KIT)

(S750000 HEATER KIT)

(S750000 HEATER KIT)

HEATER READY

FOR FIELD

INSTALLATION

Yes

No

No

No

No

No

Yes

Yes

No

ENGLISH

9

Jacuzzi Whirlpool Bath K272000AF 7/06

ROUGHING-IN REFERENCE (RECTANGULAR)

*60"

32"

CETRA™ W/INTEGRAL SKIRT, Left Hand

15-5/8"

2"

10" x 4"

9-3/8"

5-11/16"

Motor

9"

CETRA™ 532, Right Hand

12" x 4"

Motor

2"

5-3/4"

12" H x 18" L

Service Access

Opt. Service Access

*60"

32"

16"

9"

CETRA™ 536 WITH INTEGRAL SKIRT, Left Hand

*60"

36"

17-3/8"

12" x 4"

2"5-3/4"

Motor

"

*72''

Motor

ROUGHING-IN

*72''

*72''

18''

Motor

16'' x 4''

36''

ENGLISH

11-1/8''

2''

14''

AMIGA™, Left Hand

Motor

*72''

16'' x 4''

2''

14-1/2''

AMIGA™ WITH INTEGRAL SKIRT,

Right Hand

*60"

10" x 4"

32"

Motor

2"

9-3/8"

CETRA™ W/INTEGRAL SKIRT, Right Hand

*60"

Opt. Service Access

15-5/8"

5-11/16"

17-3/8''

36''

11-1/8''

12" H x 18" L

Service Access

12" H x 18" L

Service Access

24"

48"

8-1/2"

32"

16"

5-3/4"

9"

16'' x 4''

Opt. Service Access

AMIGA™, Right Hand

*72"

13-1/2" x 4"

Motor

2"

13-3/4"

(Left-hand only as shown)

BIANCA™

*60"

12" x 4"

2"

CETRA™ 532, Left Hand

2''

14''

Motor

*60"

18''

11-1/8''

Opt. Service Access

Opt. Service Access

36''

12" H x 18" L

Service Access

12" H x 18" L

Service Access

17-3/8"

Motor

16'' x 4''

36''

11-1/8''

2''

14-1/2"

AMIGA™ WITH INTEGRAL SKIRT,

Left Hand

12" x 4"

36"

Motor

18"

5-3/4"

2"

9"

Opt. Service Access

CETRA™ 536, Left Hand

*60"

17-3/8"

5-3/4"

36"

12" x 4"

Motor

2"

9"

CETRA™ 536 WITH INTEGRAL SKIRT, Right Hand

*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).

2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.

3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.

4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.

5. Not all export units come with pre-installed Pump/Motor.

Jacuzzi Whirlpool Bath K272000AF 7/06

12" H x 18" L

Service Access

12" H x 18" L

Service Access

Opt. Service Access

16"

32"

2-1/2"

5-1/4"

12" x 4"

Motor

2" 5-3/4"

CETRA™ 536, Right Hand

*60"

8-1/4"

12" x 5"

Motor

2-1/2"

Opt. Service Access

LUXURA™ 5, Left Hand

10

36"

18"

9"

*60"

8-1/4"

16"

32

2-1/2"

5-1/4"

12" H x 18" L

Service Access

12" H x 18" L

Service Access

Opt. Service Access

15" x 5"

Motor

2-1/2"

LUXURA™ 5, Right Hand

"

s

O

ROUGHING-IN REFERENCE (RECTANGULAR)

12" x 5"

2-1/2"

*66"

17"

34"

8-3/8"

LUXURA™ 5.5, Left Hand

Motor

12" H x 18" L

Service Access

Opt. Service Access

2-1/2"

5-3/8"

LUXURA™ 530 WITH INTEGRAL SKIRT, Right Hand

2-1/2"

*60"

14-3/8"

30"

12" x 5"

9-1/4"

Motor

2-1/2"

5-7/8"

MAJORA™ 6, Left Hand

42"

*72"

12" x 4"

21"

2"

10-1/2"

Motor

12" H x 18" L

Service Access

Opt. Service Access

4-3/8"

*60"

8-1/4"

15-3/8"

2-1/2"

5-1/4"

LUXURA™ 5 WITH INTEGRAL SKIRT, Left Hand

12" x 5"

2-1/2"

*66"

Motor

8-3/8"

32"

32"

LUXURA™ 5 WITH INTEGRAL SKIRT, Right Hand

ROUGHING-IN

*60"

8-1/4"

12" x 5"

Motor

2-1/2"

*60"

9-1/4"

15-3/8"

2-1/2"

5-1/4"

ENGLISH

12" H x 18" L

Service Access

Opt. Service Access

8-3/4"

21"

42"

12" H x 18" L

Service Access

12" x 5"

Motor

2-1/2"

LUXURA™ 5.5, Right Hand

*60"

2"

10" x 4"

Motor

4-3/8"

Opt. Service Access

MAJORA™ 5, Left Hand

*72"

2"

12" x 4"

Motor

17"

34"

2-1/2"

5-3/8"

12" H x 18" L

Service Access

10-1/2"

21"

42"

14-3/8"

12" x 5"

Motor

30"

2-1/2"

5-7/8"

2-1/2"

LUXURA™ 530 WITH INTEGRAL SKIRT, Left Hand

*60"

8-3/4"

2"

21"

12" H x 18" L

Service Access

Opt. Service Access

10" x 4"

Motor

4-3/8"

42"

MAJORA™ 5, Right Hand

8-1/2"

*72"

2"

20-1/2"

12" x 4"

Motor

42"

42"

*72"

12" x 4"

Motor

2"

8-1/2"

20-1/2"

Opt. Service Access

4-3/8"

MAJORA™ 6, Right Hand

12" H x 18" L
Service Access

Opt. Service

Access

*60"

10" x 4"

42"

Motor

2"

11-7/8

5-3/8"

30"

MITO™ 5, Left Hand

*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).

2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.

3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.

4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.

5. Not all export units come with pre-installed Pump/Motor.

4-3/8"

MAJORA™ 6 W/INTEGRAL SKIRT, Left Hand

pt. Service

*60"

Access

10" x 4"

Motor

11-7/8"

2"

30"

MITO™ 5, Right Hand

11

12" H x 18" L
Service Acces

42"

5-3/8"

4-3/8"

MAJORA™ 6 W/INTEGRAL SKIRT, Right Hand

12" H x 18" L
Service Access

Opt. Service

Access

*72"

10" x 4"

42"

Motor

5-3/8"

2"

36"

MITO™ 6, Left Hand

Jacuzzi Whirlpool Bath K272000AF 7/06

11-7/8"

ROUGHING-IN REFERENCE (RECTANGULAR)

"

s

NOVA™ 5, Right Hand

*60"

21"

42"

11" x 4"

Motor

12" H x 18" L
Service Access

Opt. Service Access

2''

8-1/2''

5-3/8''

NOVA™ 5 WITH INTEGRAL SKIRT, Left Hand

*60"

21"

42"

11" x 4"

9-1/4"

2''

5-1/4''

Motor

NOVA™ 6, Left Hand

*72"

21"

2"

42"

14" x 4"

8-1/2"

Motor

12" H x 18" L

Service Access

Opt. Service Access

6-7/8"

Opt. Service

Access

12" H x 18" L
Service Access

ENGLISH

11-7/8"

*72"

10" x 4"

2"

Motor

42"

ROUGHING-IN

*60"

21"

11" x 4"

Motor

12

H x 18" L

Service Acces

42"

36"

5-3/8"

MITO™ 6, Right Hand

12" H x 18" L
Service Access

21"

*60"

11" x 4"

42"

Motor

7''

8-1/2''

2''

Opt. Service Access

NOVA™ 5 W/3-SIDED TILE FLANGE, Left Hand

*60"

11" x 4"

21"

42"

Motor

2''

5-1/4''

9-1/4"

NOVA™ 5 WITH INTEGRAL SKIRT, Right Hand

5-3/8''

8-1/2''

12" H x 18" L
Service Access

2''

NOVA™ 5, Left Hand

Opt. Service Access

*60"

11" x 4"

21"

42"

Motor

Opt. Service Access

2''

7''

8-1/2''

NOVA™ 5 W/3-SIDED TILE FLANGE, Right Hand

*60"

18"

36"

4-5/8"

9"

10" x 4"

Motor

2"

Opt. Service Access

NOVA™ 536, Left Hand

12" H x 18" L

Service Access

12" H x 18" L

Service Access

Opt. Service Access

NOVA™ 536, Right Hand

*60"

10" x 4"

Motor

18"

36"

2"

4-5/8"

9"

*60"

18"

4-5/8"

10" x 4"

Motor

9"

2"

36"

NOVA™ 536 W/INTEGRAL SKIRT, Left Hand

*72"

14" x 4"

21"

42"

12" H x 18" L

Service Access

Opt. Service Access

*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).

2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.

3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.

4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.

5. Not all export units come with pre-installed Pump/Motor.

Jacuzzi Whirlpool Bath K272000AF 7/06

Motor

2"

NOVA™ 6, Right Hand

6-7/8"

8-1/2"

*60"

36"

10" x 4"

Motor

2"

NOVA™ 536 W/INTEGRAL SKIRT, Right Hand

*72"

9-3/8"

17-7/8"

6-7/8"

10" x 4"

Motor

2"

NOVA™ 636 W/INTEGRAL SKIRT, Left Hand

12

18"

4-5/8"

9"

*72"

36"

36"

10" x 4"

Motor

NOVA™ 636 W/INTEGRAL SKIRT, Right Hand

9-3/8"

2"

17-7/8"

6-7/8"

ROUGHING-IN REFERENCE (RECTANGULAR)

ROUGHING-IN

*60"

42"

12"

5"

12" H x 18" L

Service Access

Opt.

Service

Access

13" x 5"

Motor

4-1/4"

30"

SIGNA™ 5, Left Hand

*60"

4-1/4"

13" x 5"

Motor

30"

Opt.

Service

Access

42"

12"

5"

SIGNA™ 5 W/3-SIDED TILE FLANGE, Right Hand

*72"

42"

18-1/2" x 5"

Motor

12" H x 18" L

Service Access

12" H x 18" L

Service Access

*60"

42"

12"

5"

13" x 5"

Motor

4-1/4"

30"

SIGNA™ 5, Right Hand

*60"

42"

6-3/4"

16" x 5"

4-1/4"

Motor

30"

(Right hand only as shown)

SIGNA™ 5 W/INTEGRAL SKIRT

12" H x 18" L

Opt.

Service

Access

12-3/4"

*60"

13" x 5"

Motor

30"

Service Access

12" H x 18" L

Service Access

Opt.

Service

Access

SIGNA™ 5 W/3-SIDED TILE FLANGE, Left Hand

*72"

18-1/2" x 5"

12" H x 18" L

Service Access

Motor

12-1/2"

Opt.

Service

Access

36"

SIGNA™ 6, Left Hand

4-1/4"

11-

ENGLISH

42"

12"

5"

42"

1/4"

5"

1/4"

11-

5"

SIGNA™ 6, Right Hand

36"

12-1/2"

Opt.

Service

Access

*Add 1/4" (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).

2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.

3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.

4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.

5. Not all export units come with pre-installed Pump/Motor.

13

Jacuzzi Whirlpool Bath K272000AF 7/06

s

s

"

s

ROUGHING-IN

ROUGHING-IN REFERENCE (OVAL)

NOTE: These units have been provided with cutout templates included in shipping carton.

See CUTOUT information for each model on page 8.

ENGLISH

42"

12" H x 18" L
Service Access

12" x 4"

Motor

35-3/4"

71-1/2"

FRESCO™, Left Hand

4-1/2"

2"

4-1/2"

11-3/4"

11-3/4"

FRESCO™, Right Hand

62"

21-1/2"

12" x 4"

5"

9-1/2"

2"

GALLERY™ 5 OVAL, Left Hand

Motor

12" H x 18" L
Service Access

43"

43"

12" H x 18" L
Service Access

GALLERY™ 5 OVAL, Right Hand

2"

71-1/2"

62"

12" x 4"

Motor

12" x 4"

Motor

35-3/4"

2"

21-1/2"

5"

9-1/2"

42"

12" H x 18" L
Service Access

72"

72"

21"

6-7/8"

14" x 4"

Motor

2"

11-1/2"

GALLERY™ 6, Left Hand

12" H x 18" L
Service Access

42"

42"

12" H x 18" L
Service Access

GALLERY™ 6, Right Hand

14" x 4"

Motor

2"

21"

6-7/8"

11-1/2"

12-1/2"

2"

12" H x 18" L

Service Acces

14" x 4"

Motor

42"

21"

72"

GALLERY 6 UNDERMOUNT, Left Hand

72"

12" H x 18" L

13" X 6"

3"

Motor

11"

(Right-hand only)

LUNA™

36"

Service Acces

42

11"

20"

40"

71-1/2"

2"

12" x 4"

Motor

5"

MILANO™, Left Hand

NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).

2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.

3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.

4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.

5. Not all export units come with pre-installed Pump/Motor.

2"

12" H x 18" L

Service Acces

42"

14" x 4"

Motor

72"

GALLERY 6 UNDERMOUNT, Right Hand

71-1/2"

12" x 4"

12" H x 18" L

Service Access

12" H x 18" L

Service Access

Motor

MILANO™, Right Hand

12-1/2"

21"

2"

5"

11"

20"

40"

Jacuzzi Whirlpool Bath K272000AF 7/06

14

ROUGHING-IN

ROUGHING-IN REFERENCE (OVAL)

NOTE: These units have been provided with cutout templates included in shipping carton.

See CUTOUT information for each model on page 8.

72"

72"

ENGLISH

44"

Motor

12" H x 18" L
Service Access

21-1/2"

5"

9-1/2"

21"

13" X 4"

3"

4"

4-11/16"

OPALIA™, Left Hand

62"

12" x 4"

Motor

2"

RIVA™ 5, Left Hand

72"

14" x 4"

Motor

36"

12" H x 18" L
Service Access

32"

12"

42"

43"

32"

12"

43"

13" X 4"

3"

4-11/16"

36"

OPALIA™, Right Hand

12" x 4"

Motor

12" H x 18" L
Service Access

RIVA™ 5, Right Hand

42"

62"

4"

14" x 4"

Motor

2"

72"

44"

Motor

12" H x 18" L
Service Access

21-1/2"

5"

9-1/2"

21"

6-7/8"

2"

11-1/2"

RIVA™ 6, Left Hand

12" H x 18" L
Service Access

12" H x 18" L
Service Access

RIVA™ 6, Right Hand

2"

11-1/2"

6-7/8"

NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).

2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.

3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.

4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.

5. Not all export units come with pre-installed Pump/Motor.

15

Jacuzzi Whirlpool Bath K272000AF 7/06

ROUGHING-IN REFERENCE (CORNER)

"

CAPELLA™ 60, Right Hand

27"

46-5/8"

27"

60"

43-1/8"

6"

60"

34-15/16"

14" X 4"

33-1/2"

Motor

Service
Access

Opt.

Service

Access

GALLERY™ CORNER, Right Hand

60"

24"

24"

34"

47-3/4"

19" X 4"

7-1/2"

13"

34"

60"

50-1/4"

Motor

Service
Access

Opt.

Service

Access

ROUGHING-IN

ENGLISH

36 1/2"

27"

34-15/16"

43-1/8"

55"

27"

- 2" x 4" Stud

(Right-hand only as shown)

33-1/2"

60"

12" x 4"

Motor

39 1/2"

CAPELLA™ 55

14" X 4"

46-5/8"

55"

6"

12" H x 18" L
Service Access

27"

36 1/2"

44 1/2"

60"

27"

12" H x 18" L

Service Access

Opt.

Service

Access

61-1/2

Ref.

29-3/8"

12" H x 18" L

Service

Access

34-15/16"

32-1/4"

55"

Motor

16" X 4"

26"

9-7/8"

40-7/16"

- Junction Box

(Right-hand only as shown)

CAPELLA™ 55 WITH INTEGRAL SKIRT

Opt.

Service

Access

33-1/2"

60"

Motor

14" X 4"

27"

6"

43-1/8"

46-5/8"

55"

26"

32-1/2"

43-7/8"

60"

27"

60"

14" X 4"

25-1/4"

- Junction Box

(Right-hand only as shown)

CAPELLA™ SPACESAVER

33-13/16"

Motor

6"

49"

60"

25-1/4"

Opt.

Service

Access

Service
Access

33-13/16"

41-9/16"

CAPELLA 60 w/FRONT LEFT MOTOR/PUMP,

Left Hand

33-1/2"

60"

Motor

60"

14" X 4"

27"

6"

46-5/8"

27"

34-15/16"

43-1/8"

- Junction Box

(Right-hand only as shown)

CAPELLA™ 60 WITH INTEGRAL SKIRT

NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).

2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.

3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.

4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.

5. Not all export units come with pre-installed Pump/Motor.

Jacuzzi Whirlpool Bath K272000AF 7/06

Service
Access

Opt.

Service

Access

47-3/4"

CAPELLA™ 60, Left Hand

34"

60"

19" X 4"

Motor

24"

34"

50-1/4"

GALLERY™ CORNER, Left Hand

16

60"

7-1/2"

24"

13"

ROUGHING-IN REFERENCE (CORNER)

- 2" x 4" Stud

TARA™ WITH INTEGRAL SKIRT

- Junction Box

27-1/4"

35"

44"

60"

60"

46"

27-1/4"

35"

14" x 4"

Motor

(Right-hand only as shown)

ROUGHING-IN

Opt.

Service
Access

Service

Access

27-1/4"

35"

44"

60"

Motor

14" x 4"

46"

- 2" x 4" Stud

60"

27-1/4"

35"

27-1/4"

35"

60"

Motor

14" x 4"

46"

- 2" x 4" Stud

60"

27-1/4"

TARA™, Left Hand

TARA™, Right Hand

NOTE: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).

2. Service Access dimensions given are minimum. Service access is still required for units that do not have pre-installed Pump/Motor.

3. Measurements inside each unit represent cutout in floor to allow for drain/overflow.

4. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.

5. Not all export units come with pre-installed Pump/Motor.

CUTOUT

CUTOUT- CORNER BATHS

58"

(1473 mm)

59"

Ref.

Overflow

90˚

25-1/2"

(648 mm)

CAPELLA 60 W/ FRONT LEFT MOTOR/PUMP

(Motor/Pump position not shown.)

58"

(1473 mm)

22-5/8"

m

Overflow

)

GALLERY CORNER,

90˚

(575 m

Drain

45-9/16"

(1157 mm)

CAPELLA 60 &

3" RADIUS
CORNERS
(5 PLACES)

Drain

50"

(1270 mm)

Right Hand

(1473 mm)

Motor

58"

(1473 mm)

25-1/2"

(648 mm)

58"

22-5/8"

(575 mm)

90˚

90˚

57"

Ref.

Service

35"

44"

57"

Ref.

Opt.

Access

Service
Access

(1473 mm)

90˚

22-5/8

(575 mm)

59"

Ref.

90˚

25-1/2"

(648 mm)

58"

Motor

"

GALLERY CORNER,

58"

(1473 mm)

Overflow

TARA CORNER CUTOUT

3" RADIUS
CORNERS
(5 PLACES)

Drain

50"

(1270 mm)

Left Hand

Drain

45-9/16"

(1157 mm)

Right Hand

Motor

58"

(1473 mm)

Overflow

58"

(1473 mm)

25-1/2"

(648 mm)

90˚

22-5/8"

(575 mm)

90˚

ENGLISH

59"
Ref.

90˚

25-1/2"

(648 mm)

58"

(1473 mm)

Motor

TARA CORNER CUTOUT

45-9/16"

(1157 mm)

Left Hand

17

Drain

(1473 mm)

Overflow

58"

25-1/2"

(648 mm)

90˚

Jacuzzi Whirlpool Bath K272000AF 7/06

Framing and Support

INSTALLATION INSTRUCTIONS

The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor.

The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. Refer to the table under total

weight for your model. The unit must be supported from the bottom of the bath and not from the bath rim or tile flange. If the subfloor is level

and a continuous surface, no other preparation is necessary. You can proceed to install the bath. If the subfloor is not level, you MUST level the
entire surface prior to installing the bath. The use of materials that provide a level installation are allowed provided the method used will insure
a level bath that is supported from the bottom. Materials that may be used are a floor leveling compound, mortar, plaster or minimal expansion
structural foam having a density of a minimum of 5 lbs./cubic ft.; however the bath must remain level in order for it to drain properly and all foam
feet must make full contact with the leveling material. Both sides of a joint or splice of subfloor should be level to each other. When attaching

ENGLISH

baths with flanges to stud wall, use shims to fill any gaps between the bath flange and studs.

The rim of the bath is not designed to support weight. If finish material is to overlap or contact the bath, the added weight must be fully self-

supporting.

The protective film liner inside the bath is used to prevent damage to the finish during installation. Before installation, remove

liner to inspect for any defects, reapply and do not remove until final cleanup.

Important: If a skirt is to be used, it must be installed at the time of unit installation – refer to skirt installation instructions. Install

optional trim parts when all installation has been completed.

TYPICAL INSTALLATIONS

MORTAR OR ADHESIVE

FLASHING

TILE

MORTAR OR ADHESIVE

SEALANT

SEALANT

TILE

PLASTER

FILLER

FLANGE

FINISHING
MATERIAL

MORTAR

CEMENT
BOARD

BATH RIM

NAIL
OR
SCREW

STUD
WALL

SILICONE
SEALANT

1" X 4" (NOT FOR
SUPPORT)

OPTIONAL TILE FLANGE KIT

1" X 4" (NOT FOR SUPPORT)

FLUSH TO WALL

SUB-FLOOR

FLASHING

1" X 4" (NOT FOR SUPPORT)

SEMI-SUNKEN

NOTE: ON the Riva 5 and Riva 6, the discharge plumbing extends slightly beyond the bath rim. When installing either bath as semi­sunken, lower the pump/motor side in first into the cutout.

TYPICAL FLANGE MOUNTING DETAIL

SHIM IF
NECESSARY
TO FILL GAPS
BETWEEN
STUD
AND FLANGE

STUD

CAULKING

FLANGE

1/8" GAP

TILE

CEMENT
BOARD

TILE
ADHESIVE

ATTACH WITH
SCREWS
PROVIDED

STUD

FLANGE

SHIM IF
NECESSARY
TO FILL GAPS
BETWEEN
STUD
AND FLANGE

STUD

CAULKING

FLANGE

1/8" GAP

TILE

CEMENT
BOARD

TILE
ADHESIVE

ATTACH WITH
SCREWS
PROVIDED

STUD

FLANGE

1"X 4"
(NOT FOR
SUPPORT)

UNDERMOUNT INSTALLATION OPTIONS

The undermount gives the opportunity to be flexible in the design and location of the bath. Examples are shown for possible
installations. Refer to pages 23-24 for undermount installation instructions.

Jacuzzi Whirlpool Bath K272000AF 7/06

FREE STANDINGCORNER NICHE

18

SUPPORT FOR CORNER BATHS

H

2" x 4" STUD

APPLY
ADHESIVE

(50,8 mm x 101,6 mm)

T

INSTALLATION INSTRUCTIONS

Skirts

INTEGRAL SKIRT MOUNTING DETAIL

FINISHING

MATERIALS

CAULKING BEAD

SKIRT
PANEL

Corner Baths with Skirt

If an optional skirt is used on a corner bath, additional support is
necessary in the front of the unit. Measure the height from the floor
to the underside of the bath rim. Cut two 2" x 4" studs, apply adhe­sive to both ends and install (See specifications in ROUGHING-IN
REFERENCE

(CORNER)).

ENGLISH

U FRAME SKIRT MOUNTING DETAIL

FINISHING MATERIALS

SECURE SHELL CLIP
UNDER CENTER
BATH RIM

FILLER (Optional)

SKIRT
PANEL

SECURE BOTTOM OF FRAME TO FLOOR

CAULKING
BEAD

SKIRT
FRAME

Removable Skirt Panel

Removal and Installation

To remove panel, grab a top corner of access panel and pull outward
to release the first Dual Lock fastener. Then work around the
perimeter pulling access panel outward to release the remaining
dual Lock fasteners.
To reinstall, align access panel such that the Dual Lock fasteners
on the access panel match to the Dual Lock fasteners on the tub
skirt. Engage each Dual Lock pair until all are snapped into place.

PEEL BACK CORNER

O BEGIN DISCONNECTING

DUAL LOCK™ FASTENER

19

Jacuzzi Whirlpool Bath K272000AF 7/06

MOTOR

AREA

A

AREA

B

FRONT

INSTALLATION INSTRUCTIONS

Service Access

For partially or fully sunken installations, allow for access to ser­vice connections. It is the installer's responsibility to provide suffi­cient service access. The recommended minimum dimensions al­lowable for service to the bath are shown in the "Service Access"
illustration and on the ROUGH-IN drawing for that tub.

ENGLISH

Provide adequate area around unit for air circulation for cooling
the motor and to supply sufficient air to the jets. Do not insulate this
area or around motor.

Optional RapidHeatTM Service Access

Where tubs have been ordered with the optional RapidHeat
heater consider an additional service access.

If service access has not been provided, it is the home owners
responsibility to remove the bath and provide the required
access, should a repair become necessary.

Service Access with Skirt

An optional skirt fits along the side of the bath for above-floor
installations and is also an access panel for servicing. Allow a space
of at least 8 inches away from the bath for skirt removal.

The skirt is designed to accommodate the added height of the
tile, linoleum, or other floor coverings up to 1-1/4" (31,75 mm) above
the floor, and will be flush with the floor when installed.

More detailed instructions on skirt installation are provided with
the optional skirt assembly.

SERVICE ACCESS

18"

(45,7 cm)

RIGHT HAND UNIT SHOWN

A - Preferred access
B - Acceptable alternative if access A is not possible
C - Additional access for equipment (Optional)

NOTE: Left hand unit access is on the opposite
side (mirror Image).

(CORNER BATHS)

C

36"

(91,4 cm)

A

24"

(60 cm)

B

20"

(50,8 cm)

Service Access with Integral Skirt

SERVICE ACCESS

TM

SERVICE ACCESS

the design of the bath environment and having full understanding
that in this case, it may be necessary to remove the unit for service.

without complete access to the plumbing system. This would ne­cessitate the removal of the unit. Although this practice is not com­monly implemented, it is an acceptable method.

Service access is through the removable skirt panels.

(WITH INTEGRAL SKIRT)

REMOVABLE SKIRT
ACCESS PANELS

FRONT

ALTERNATE
ACCESS

In some cases, access may not have been provided because of

If this is the case, diagnosing a problem may not be possible

ACCESS AREA

(WITHOUT SKIRT)

12"

(30,5 cm)

18"

(45,7 cm)

MOTOR

PREFERRED
ACCESS

MOTOR

18"

(45,7 cm)

12"

(30,5 cm)

SERVICE ACCESS

(BG55, CAPELLA 60 FRONT LEFT MOTOR CORNER BATH ONLY)

12"

(30,5 cm)

18"

(45,7 cm)

Preferred access area

Jacuzzi Whirlpool Bath K272000AF 7/06

In some cases access may have been provided in Area A but
service is required in Area B which requires the unit to be pulled for
service and reinstalled.

If service access has not been provided, it is the homeowner's
responsibility to remove the bath and provide the required
access, should a repair become necessary.

20