SUMMER RAIN™ II
2 PERSON SHOWER SYSTEM
ONE WALL
INST ALLATION AND OPERATING INSTRUCTIONS
Jacuzzi Whirlpool Bath© BY82000 03/05
IMPORTANT SAFETY INFORMATION
Do not place or use electrically connected devices, such as television, radio, or stereo speakers, lights, hair
dryers, or telephones, within 1.5 m (5 feet) of shower.
Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical
installation according to codes are required for proper installation and user satisfaction. We recommend that
a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath
cover improper installation related problems.
©
products. Our warranty does not
CONTENTS
Specifications _________________________________________________________________________ 2
Enclosure Specifications ________________________________________________________________ 3
Rough-in Reference ____________________________________________________________________ 3
Component Identification ________________________________________________________________ 4
Base Installation _______________________________________________________________________ 5-7
Tower and Doors Installation _____________________________________________________________ 8-15
Operation ___________________________________________________________________________ 16-17
Maintenance __________________________________________________________________________ 18
Tower Fixture Repair Parts _______________________________________________________________ 19
Tower Plumbing Repair Parts _____________________________________________________________ 20
Warranty ____________________________________________________________________________ 23-24
Save These Instructions for Future Use.
Owner's Record
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Number _____________________________________________________________
Model ____________________________________________________________________
1
Jacuzzi Whirlpool Bath© BY82000 03/05
SPECIFICATIONS
Important: Read complete instructions before beginning installation.
Each unit arrives ready for installation, equipped with base, glass and associated hardware.
Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been
made.
Immediately upon receipt, inspect the base and other components before installing. Check all carton inserts for
parts and hardware. Should inspection reveal any damage or defect in any component, do not install the unit. Damage
or defect to any component claimed after the unit is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's
responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims
for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty
information packed with the product.
Jacuzzi Whirlpool Bath© is not responsible for any defect that could have been discovered, repaired, or avoided by
following this inspection.
BASE SPECIFICATIONS
DIMENSIONS
72"
27-11/16"
48"
21-1/16"
18-11/16"
PRODUCT WEIGHT (Base and Enclosure )
950 lb
(431 kg)
TOP VIEW
30-1/4"
1-1/2" TILE FLANGE
27-1/4"
FRONT VIEW
TOTAL WEIGHT/FLOOR LOADING
1266.6 lb (574.5 kg)
63.3 lb/sq. ft. (332.1 kg/m2)
1/2" FLEXIBLE
WATER SUPPLY
HOSES UNDER
BASE
(BOTH SIDES)
AIR SUPPLY HOSE
6-1/2"
4-1/2"
NOTE: MINIMUM WATER PRESSURE FOR THE SYSTEM IS 45 PSI WITH 3/4" HOT & COLD SUPPLY SERVICE.
2
Jacuzzi Whirlpool Bath© BY82000 03/05
ENCLOSURE SPECIFICATIONS
84"
72"
FRONT VIEW SIDE VIEW
ROUGH-IN REFERENCE
72"
1" TILE FLANGE
27-11/16"
48"
BLOWER MOTOR FOR
UNITS WITH AIR
AIR LINE FOR
UNITS WITH AIR
36"
48"
38-15/16"
TOP VIEW
3
Jacuzzi Whirlpool Bath© BY82000 03/05
COMPONENT IDENTIFICATION
WATER TOWER
CENTER SUPPORT RAIL
AIR TOWER
DOOR POST
DOOR POST
SIDE SUPPORT RAIL
WATER TOWER
GLASS SIDE PANEL
RAIL BRACKET
AND COVER CAP
WALL POST
SEAT
GLASS SIDE PANEL
GLASS DOORS
BASE
FRONT VIEW SIDE VIEW
WALL POST
GLASS SIDE PANEL
WATER TOWER
DOOR POST
GLASS SIDE PANEL
SEAT
BASE
DRAIN
DOOR POST
AIR TOWER
WALL POST
WATER TOWER
Jacuzzi Whirlpool Bath© BY82000 03/05
GLASS DOORS
(SUPPORT AND SIDE SUPPORT RAILS NOT SHOWN)
4
BASE INSTALLATION
SPREAD MORTOR OR LEVELING
COMPOUND ETC EVENLY OVER ENTIRE AREA
PRELIMINARY ROUGH-IN
The floor structure beneath the unit must be able to
support a total weight of the unit and bather. Refer
to page 2, SPECIFICATIONS, for weight specifications . Refer to COMPONENT IDENTIFICATION on
page 4 to help identify parts.
STEP 1
Provide an opening in the subfloor no less than 5" x 5"
square. This opening should be located on the center
lines of the shower base drain hole.
C
L
C
L
2" WASTE PIPE
5"X5" OPENING
(MIN. AS POSSIBLE)
INSTALLATION INSTRUCTIONS
STEP 2
Remove the stainless steel strainer from the drain
assembly. Disassemble the locknut and two gaskets
from the back of the drain assembly. Apply a 1/4" bead
of caulking (silicone) to the drain hole and insert the drain
assembly. Replace the rubber washer, fiber washer,
and lock nut in that order. Hand tighten the locknut.
Remove excess sealant from finished side.
Apply a lubricant (common household liquid soap
works well) to the inside of the rubber seal of the drain
assembly.
STRAINER
APPLY LUBRICANT
DRAIN
ASSEMBLY
SHOWER BASE
RUBBER WASHER
FIBER WASHER
SILICONE
SEALANT
NUT
CAUTION: A nonflammable protective barrier must
be placed between soldering work and base unit to
prevent damage to the base.
STUD
WALL
COPPER FITTINGS
AND TUBING
NOT PROVIDED
45° COPPER ELBOW
PROVIDED (2)
DETAIL 1
STEP 3
If the subfloor is level, no other preparation is necessary. You can proceed to install the shower base. If the
subfloor is not level, level the subfloor by spreading floor
leveling compound, mortar, plaster or minimal expansion structural foam with a minimum density of 5 lbs./
cubic feet EVENLY over ENTIRE area where base will
be installed. The compound used MUST make contact
with the entire bottom surface of the base. Both sides
of a joint or splice of subfloor should be level to each
other. Level and support waste pipe cutout area greater
than 5" x 5". The base is NOT to be supported by the tile
flange.
5
Jacuzzi Whirlpool Bath© BY82000 03/05
TIGHTEN SEALING NUT
TOOL
(INCLUDED)
BASE INSTALLATION
)
LOWER SEAT FRAME OVER
FLANGE ON BASE
APPLY
SEALANT
ON
FLANGE
BLOCKING
SEAT
FRAME
STEP 4
Before installing the base, make sure the 4 water
supply hoses are routed to seat area. If you have a with
Air unit also route the air supply hose to the seat area.
If you have a with Air unit also pull the 2 flow switch
cables and the control panel cable through base at this
time.
With the drain fitting passing over the center of the
drainpipe, lower the shower base carefully into place,
push down firmly until the base is in place.
You must check the level of the base in two directions.
Do not lift a corner of the shower base to level the base.
This will cause a loss of contact with the mortar and void
your warranty. Attach the shower base flange to the stud
wall and blocking with self-drilling screws (included).
Use a minimum of 3 screws per flange section.
FLOW
CONTROL
PANEL
CABLE*
POSITION BASE OVER CENTER OF
DRAIN PIPE AND SET INTO PLACE
* ONLY WITH AIR TOWER UNITS
SWITCH
CABLE*
(2X)
STEP 5
Before installing the seat frame, apply silicone sealant
around mating flange on base. Lower seat frame onto
flange and base. Attach the seat frame flange to the stud
wall and blocking with self-drilling screws (included).
Use a minimum of 3 screws per flange section. Clean up
any excess sealant.
NOTE: If there is any gap between seat frame flange
and stud or blocking, shims MUST be used to prevent distortion or cracking of the flange. See Shim
Instructions.
STEP 6
With a large screwdriver and the tool included with the
drain, tighten the inside compression nut to seal the
drain pipe connection. After drain is fully installed, test
for proper drainage. If the shower base does not drain
properly, rectify this condition before proceeding with
the installation. Jacuzzi Whirlpool Bath© is not re-
sponsible for removal and/ or reinstallation costs.
NOTE: If there is any gap between base flange and
stud or blocking, shims MUST be used to prevent
distortion or cracking of the flange. See Shim Instructions.
SHIM INSTRUCTIONS
TILE
FLANGE
GAP
USE
SCREWS
(PROVIDED)
STUD
INCORRECT
Jacuzzi Whirlpool Bath© BY82000 03/05
SHIM
TILE
FLANGE
USE
SCREWS
(PROVIDED
STUD
CORRECT
NOTE: Watertight installation of the drain is the
installer’s responsibility. Drain leakage is excluded
from the Jacuzzi Whirlpool Bath© warranty.
Replace the strainer and tape over the drain hole to
prevent finishing material from entering drain.
6
BASE INSTALLATION
STEP 7
Place cement board or equivalent on top of shower
base flange and secure to studwall.
Apply tile (or other finishing material) leaving a 1/8" gap
between the finishing material and the shower base
flange lip. Seal this gap with silicone sealant. Leave a
minimum 1/4" gap at the back and front corners of the
shower base to allow drainage from leakage through
unsealed tiled grout.
TILE
CEMENT
BOARD
TILE
ADHESIVE
STUD
FLANGE
SHIM IF
NECESSARY
TO FILL GAPS
BETWEEN STUD
AND FLANGE
STUD
1/8" GAP
BETWEEN
BASE &
TILE
CAULKING
DO NOT FILL
THIS AREA
ATTACH WITH
SCREWS PROVIDED
See Shim Instructions on page 6.
STEP 8
Filling the area marked DO NOT FILL will prevent
moisture from properly draining back into the base
through weep holes. This moisture is due to leakage
through the tile grout. Sealing the tile grout will reduce
or prevent this leakage.
CEMENT
BOARD
STUD
SHIM IF NECESSARY
DO NOT FILL
1-1/8" MAXIMUM
NO MINIMUM
TILE
GROUT
SILICONE
SEALANT
STEP 9
NOTE: ALLOW 24 HOURS DRYING TIME BEFORE
BEGINNING THE TOWER AND DOOR INSTALLATION.
CLEAN UP AFTER BASE INSTALLA TION
To avoid dulling and scratching the acrylic surface of the base, never use abrasive cleaners. A mild liquid detergent
and warm water clean soiled surfaces.
Remove spilled plaster with a wood or plastic edge. Metal tools scratch the surface. Spots left by plaster or grout
can be removed if lightly rubbed with detergent on a damp cloth or sponge.
Paint, tar, or other difficult stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing
alcohol).
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry
sandpaper. You can restore the glossy finish to the acrylic surface of the base with a special compound, Meguiar’s
#10 Mirror Glaze. If not available, use automotive rubbing compound followed by an application of automotive paste
wax.
Major scratches and gouges which penetrate the acrylic surface require refinishing. See your Jacuzzi Whirlpool
Bath© dealer for special instructions.
7
Jacuzzi Whirlpool Bath© BY82000 03/05
TOWERS AND DOORS INSTALLATION
WASHER (2)
BOLT 5/16" (2)
AIR SUPPY PIPE
AIR
TOWER
CONTROL
PANEL CABLE
THESE INSTRUCTIONS ARE FOR SUMMER RAIN
UNITS WITH AND WITHOUT AIR FEATURE OPTION.
REFER TO COMPONENT IDENTIFICATION ON PAGE
4 TO HELP IDENTIFY PARTS.
All wall finish tiling, trim, and sealing should be
completed before beginning this part of the installation.
WATER TOWER DETAIL
FLOW
SWITCH
CABLE*
BOLT (5/16")
STEP 1
Position each tower on mounting pad on base. For the
shower towers, feed hot and cold supply line through
appropriate holes in bottom of tower. For air feature,
feed air line through large hole on bottom cap of the air
tower. Check with a level when attaching towers to base.
Tighten tower base bolts after leveling (1 bolt per shower
tower and 2 bolts for air tower).
WASHER
SHOWER
TOWER (2X)
COLD HOT
* ONLY WITH AIR TOWER UNITS
STEP 2 (WITH AIR FEATURE ONLY)
Route control panel cable up through air tower and
connect to control panel.
Jacuzzi Whirlpool Bath© BY82000 03/05
BLACK LEAD
REAR OF CONTROLLER
STEP 3 (WITH AIR FEATURE ONLY)
Route flow switch cables up through water towers and
connect to flow switch on both shower towers.
FLOW
SWITCH
FROM
CONTROL
BOX
8
STEP 4
RAIL HOLD
DOWN BRACKET
(1 PER AIR TOWER)
SCREW (8 PER WATER TOWER)
(4 PER AIR TOWER)
(2 PER WATER TOWER)
TOWERS AND DOORS INSTALLATION
Take the side support rails and install a cover cap and wall bracket on each end. Place the center support rail into slot
on each tower. If rail does not readily fit into slots, it may be necessary to loosen the bolts holding towers to base (it
may only be necessary to loosen one tower). DO NOT FORCE CENTER RAIL INTO SLOTS. With center support rail
in position, install hold down brackets but do not tighten screws. Place the side support rails into the slot on each water
tower. With side rails in position install hold down brackets, but do not tighten screws. Check side support rails for
level and mark on the finished wall where to attach rail bracket. See DETAIL A. Drill 3/16" holes and secure bracket
with screws and wall anchors provided. Slide cover cap over rail bracket. If a tower bolt was loosened, retighten while
checking the plumb of the tower. Tighten screws on all hold down brackets.
COVER CAP (2)
SIDE SUPPORT RAIL (2)
HOLD DOWN BRACKETS (5)
RAIL BRACKET (2)
CENTER SUPPORT RAIL
DETAIL A
ATTACH RAIL
BRACKET TO WALL
SECURE RAIL TO
BRACKET (TURN CW
TO TIGHTEN)
MOVE COVER CAP
OVER BRACKET
WATER TOWER DOOR POST
WATER TOWER JAMB
9
Jacuzzi Whirlpool Bath© BY82000 03/05
TOWERS AND DOORS INSTALLATION
SHUT OFF
VALVES
(PROVIDED)
COLD
HOT
CAULK AROUND SUPPLY
PIPING AND INSIDE TOWER BASE
STEP 5
Two shut-off valves are provided per water tower. To
hook up supply lines, unscrew valves from braided line.
Using thread sealant, screw each valve to stub out at
bottom of tower. Then reconnect braided line using
provided gasket. Do not twist or kink supply lines when
connecting. Perform this step for both water towers.
STEP 4 (WITH AIR FEATURE ONLY)
Attach air supply pipe to air tower plumbing.
Jacuzzi Whirlpool Bath© BY82000 03/05
10
TOWERS AND DOORS INSTALLATION
LOCKING
NUT
ADJUSTING
SCREW (12mm)
DOOR POST
HINGE
BARREL
STEP 6
Move the door assembly to the door post on water tower
and slide the assembly into the door post. Locate the
base of the door into the slot of serrated door positioner
that positions the hinge barrel as shown.
WATER
TOWER
GLASS DOOR
BOTTOM OF
DOOR FRAME
SHOWER BASE
HINGE BARREL
STEP 7
Check that the magnetic mouldings on door and air
tower overlap. Insert adjusting bolt with locking nut into
fixed nut in top cap (See below). Adjust the door with
adjusting screw until the glass is parallel with shower
base and door moulding mates with water tower moulding. It may be necessary to reposition the door into
another slot (See STEP 6) which can be done without
removing door from wall post. To do so remove the
adjusting screw from wall post, lift the door slightly to
reposition. Reinsert adjusting screw and locking nut and
adjust glass door. After final adjustment, lock this position with locking nut. Repeat for other door.
STEP 8
Install cover cap by sliding over adjusting screw and
bracket.
COVER CAP
11
Jacuzzi Whirlpool Bath© BY82000 03/05
TOWERS AND DOORS INSTALLATION
STEP 9
Position the fixed glass wall post so that the glass side
panel will be parallel with the outside edge of the base.
The fixed glass wall post position may vary slightly due
to the anchored location of the water tower.
FINISH WALL
GLASS SIDE
PANEL MOUNTED
PARALLEL TO
EDGE OF BASE
EDGE
OF BASE
STEP 10
Level the post in its proper position and mark where
screw holes are to be drilled. Drill 3/16" holes and secure
with wall anchors and screws provided. Apply tape
(provided) firmly over screw heads.
STEP 11
Slide fixed glass panel all the way into wall post.
TAPE (3)
WALL POST
SCREWS (3)
Jacuzzi Whirlpool Bath© BY82000 03/05
12
TOWER AND DOOR INST ALLATION
WALL POST
GLASS
GLAZING GASKET
INSIDE OF
ENCLOSURE
APPLY SEALANT
STEP 12
Align the glass with glass jamb and insert. Repeat
STEPS 8 through STEP 10 for the other fixed glass
panel.
STEP 13
Install glazing gasket on fixed glass walls post and jambs
on the outside. Note orientation of gasket. Soapy water
may help to insert the glazing gasket.
NOTE: The glazing is to be installed on the outside of
enclosure for both wall posts and tower jambs.
Clean any soapy residue off the glass and towers. On
the inside of enclosure, apply sealant to entire length
of glass and wall post as well as the entire length of
the glass and tower jamb.
GLASS
APPLY SEALANT
INSIDE OF
ENCLOSURE
13
GLAZING GASKET
JAMB
Jacuzzi Whirlpool Bath© BY82000 03/05
GLASS
DOOR
WASHERS
LARGE
WASHER
INTERIOR OF
SHOWER
DOOR
HINGE
TOWER COVER
INSERT THIS SIDE FIRST
TOWER COVER
TOWER TOP PLATE
TOWERS AND DOOR INSTALLATION
STEP 14
Install fixed glass cover cap on wall post.
COVER CAP
STEP 15
Install all towers' top cover
SCREWS
(2 PER TOWER
TOWER
TOP COVER
STEP 16
Install handles as shown. Note orientation of handle.
Hand tighten knob. Flat screw has a screw driver notch.
Do not over tighten either knob or flat screw as cracked
glass may result.
STEP 17
Turn on water supply and check for leaks. Correct any
leaks before continuing the installation.
STEP 18
Install all tower cover panels as shown. Align left side of
tower cover panel with inside seat in each tower. Begin
each panel's snap in at the top of the tower.
Jacuzzi Whirlpool Bath© BY82000 03/05
14
TOWERS AND DOOR INSTALLATION
STEP 19
Seal all around all bases of towers with sealant. Also seal the inside of both wall posts, jambs, door posts and bottom
of both glass side panels on the inside only.
APPLY SEALANT ALONG BASE AND
SIDE OF WALL POST AND GLASS AND
WALL POST (BOTH SIDES)
APPLY SEALANT
ALONG BASE
OF FIXED GLASS
(BOTH SIDES)
APPLY SEALANT ALONG SIDE OF JAMB
AND DOOR POST AND JAMB AND GLASS
(BOTH TOWERS)
APPLY SEALANT ALL AROUND
TOWER BASES (ALL 3 BASES)
(RAIL NOT SHOWN)
STEP 20
Remove tape over drain and any other masking or protective covers. Proceed with clean up.
CLEAN UP AFTER T OWERS AND DOOR INSTALLA TION
To avoid dulling and scratching the tower surfaces and support rails never use abrasive cleaners. Use a mild liquid
detergent and warm water clean soiled surfaces. Use a mild glass cleaner to clean glass panels and doors.
Paint, tar, or other difficult stains can be removed with normal glass and finish cleaners. Use caution when applying
these products to coated metal surfaces. Test in an inconspicuous place before using. Do not use abrasives, alcohol,
acetone, ammonia or other solvents on any tower component.
Scratches to towers and metal components may not buff or polish out requiring surface refinishing or replacement.
Consult your Jacuzzi Whirlpool Bath© dealer or visit our website at: http://jacuzzi.com/ for a list of authorized finish
contractors.
15
Jacuzzi Whirlpool Bath© BY82000 03/05
SHOWER TOWERS
Shower Head
OPERATION
Shower Head
There are three selectable positions: Jet, Normal Pulsating, and Aerated flow.
Body Sprays (2 Upper and 2 Lower)
To adjust the flow and intensity, turn as shown. The
spray can also be turned to change the direction of the
spray.
LESS FLOW AND INTENSITY
MORE FLOW AND INTENSITY
Body Sprays
(2 Upper & 2 Lower)
Diverter Control
STOP RELEASE
Temperature Valve
Diverter Control
To turn ON water, turn the inner knob clockwise and
adjust for more or less flow.
The outer knob will divert the water to body sprays,
shower head (position shown), and foot temperature
tester. Water flow is proportional to each function when
outer knob is positioned between main functions. When
outer knob is pointing to white line on outer dial face (half
way between main functions) water will be diverted
equally.
SHOWER
HEAD
BODY
SPRAY
OUTER
KNOB
FOOT
TEMPERATURE
TESTER
INNER
KNOB
Foot Temperature
Tester
Jacuzzi Whirlpool Bath© BY82000 03/05
Temperature Valve
The temperature of the mixed water is adjusted by
means of the graduated handle. This handle has as
safety stop set at 100o F (38oC). To increase the temperature, press the RED button to release the stop and
continue turning the handle.
Foot Temperature Tester
16
AIR TOWER
OPERATION
Air Jet (12)
Controller
AIR TOWER CONTROLS
ON/OFF
BUTTON
AIR FLOW LED
To turn ON press ON/OFF button or turn ON water at either shower tower.
The unit will then automatically go into a preheat cycle to heat the air
transmission pipes. There will be a 5 (five) minute pause while the system
preheats. During this time both LEDs will be ON. When ready for drying,
press the ON/OFF button. Heat and air flow will rise together (only at initial
start-up). After reaching the desired flow, the temperature may be decreased or increased using the Temperature button. The air flow may also
be adjusted.
INCREASE
TEMPERATURE
CONTROLLER
DECREASE
TEMPERATURE
AIR FLOWAIR TEMPERATURE LED AIR TEMPERATURE
Note: Temperature and air flow are factory set with a predetermined heat
and air speed.
17
Jacuzzi Whirlpool Bath© BY82000 03/05
MAINTENANCE
To remove any lime scale from the shower head and body sprays, rub with your finger the outer ring of nozzles on the
shower head and all nozzles on the body spray.
To clean the foot temperature tester, unscrew the nozzle and back flush the wire mesh filter. Do not use metal tools
(such as scissors or screwdrivers, etc.) to clean the body sprays, shower head or foot temperature tester.
To clean the base, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to
a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic
finishes. If Meguiar's is not available, an acrylic polish of equal quality or automotive paste wax is acceptable.
The glass can be cleaned with any glass-cleaning product available on the market.
Do not use abrasives, alcohol, acetone, ammonia or other solvents on any tower component.
The thermostatic valve has 2 screen filters that should be cleaned periodically. To remove the filters turn off hot and
cold supplies. Remove each water tower cover. Disconnect the supply hoses from the valve and remove filter from
the hose. Remove any debris. Reinstallation is the reverse of removal. Turn on hot and cold supply and check for
leaks before replacing tower cover.
Jacuzzi Whirlpool Bath© BY82000 03/05
18
TOWER FIXTURES REPAIR PARTS
1 (5X)
2 (5X)
(5X)
3
TOWER ASSEMBLY
6
7 (PART OF U547000)
4
5
8
9 (5X)
10
11 (4X)
12
13
14
15
16
PART OF D709827
1. C546000 Lock Nut, 1/2" NPT WP (5X)
2. G559000 Ring Compression SS (5X)
3. G560000 Washer Rubber (5X)
4. U546000 (Part of U547000) Nut Valve Transfer, Chrome
5. U566000 Gasket, 1.41 ID x .063 Thick
6. U547000 Valve, Mixer/Transfer Assembly
7. U550827 (Part of U547000) 567000 Nut, Mixer Valve, Chrome
8. U567000 Gasket, 1.9 ID x .063 Thick
9. G432000 Nipple, 1/2" Close
10. U217827 Shower Head, Chrome
11. U215827 Jet, Wall Body, Chrome
12. U219827 Face Plate, Transfer Valve, Chrome
13. U546827 Nut Transfer Valve, Chrome
14. U545827 Collar, Transfer Valve, Chrome
15. U544000 O-Ring, Transfer Valve
16. U543827 Knob, Flow Control, Chrome
17. U549827 Collar, Mixer Valve, Chrome
18. U548827 Knob, Mixer Valve Chrome
19. D709827 Fill Spout Assembly, Stubby, Chrome
17
18
WASHER (PART OF D709827)
19
19
Jacuzzi Whirlpool Bath© BY82000 03/05
TOWER PLUMBING REPAIR PARTS
ITEM
NO. QTY. PART NO. DESCRIPTION
1 1 Y221000 TOWER, 2 PERSON SHOWER
2 3 U401000 FTG, ELL, .50" FST x 10 mm BARB
3 4 Y724000 1/2" ELBOW, SLIP x THREAD, SCH 40
4 3 7164000 ELL, STREET, .50", 90
5 2 0455000 1/2" TEE
6 1 7269000 1/2" PIPE, FLEX 5 1/2" LG
7 1 7269000 1/2" PIPE, FLEX 5 1/2" LG
8 1 U547000 VALVE, MIXER/TRANSFER ASSEMBLY
9 1 Y723000 1/2" TEE, S x S x THREAD, SCH 40
10 1 7269000 1/2' PIPE, FLEX 13.75" LG
11 2 U405000 TUBING, PVC REINFORCED, 31.00" LG
12 1 7269000 1/2" PIPE, FLEX 5" LG
13 1 7269000 1/2" PIPE, FLEX 6" LG
14 1 7269000 1/2" PIPE, FLEX 8" LG
15 1 U137827 CAP, BOTTOM, TOWER, CH
16 2 U540000 1/2" FLEX HOSE, 38", FEMALE SWIVEL HEADS
17 2 GASKET GASKET SUPPLIED WITH HOSE
18 4 U421000 WASHER, FTG, .7 OD
2
1
18
19 1 U400000 FTG, STRAIGHT, 1/2" FTS x 10 mm BARB
5
4
4
11
7
o
18
19
8
11
18
2
10
3
9
6
14
3
5
4
12
13
3
16
18
2
15
Jacuzzi Whirlpool Bath© BY82000 03/05
17
20
21
Jacuzzi Whirlpool Bath© BY82000 03/05
r
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath© has obtained applicable code (standards) listings generally available on a national basis for products of
this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.
Jacuzzi Whirlpool Bath© makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath National Headquarters
P.O. Box 702168, Dallas, TX 75370-2168
Service Support: (800) 288-4002
Printed on Recycled Pape
Jacuzzi Whirlpool Bath© BY82000 03/05
Printed in U.S.A.
Jacuzzi Whirlpool Bath Limited Warranty
Designer Collection Shower Product
Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer
Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the
unit or its equipment in accordance with the following terms and conditions.
TWO YEAR LIMITED WARRANTY ON BATHS
Our limited warranty on Designer Collection Bath products is for two (2) years. Our warranty covers the unit and factory-installed components against
defects in material or workmanship. Warranty coverage begins on the date the unit was originally purchased by the user.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
Our warranty on options and accessories manufactured by the Company is for ninety (90) days for parts only. Our warranty covers options and accessories
manufactured by the Company against defects of material or workmanship. Warranty coverage begins on the date the option or accessory was originally purchased
by the user.
Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other person, or resulting from, without
limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.); modification of any type for any reason (including modification
to meet local codes); improper installation (including installation not in accordance with instructions and specifications provided with the unit); connections
supplied by the installer of the equipment; improper voltage supply or unauthorized electrical modification; misuse; incorrect operation, or lack of proper routine
maintenance; operation of the unit without specified minimum amount of water or at inappropriate water temperature; use of abrasive or improper cleaners; or
acts of God, such as lightning, floods, earthquakes, etc.
In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause
(e.g., water damage to carpet, ceiling, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts when pool and/or spa
chemicals are used in the unit; optional bath equipment not manufactured by the Company but supplied by Dealer, installer or the Company; the unit's prior usage
as an operational display; or defects that should have been discovered before installation. This limited warranty does not include: labor, transportation, or other
costs incurred in the removal and/or reinstallation of the original unit and/or installation of a replacement unit; any costs relating to obtaining access for repair;
or loss of use damage, including loss of sales, profit or business advantage of any kind under any circumstances. Bath units are excluded from any warranty coverage
if any addition, deletion, or modification of any kind whatsoever has been made to the unit (or to any component).
Warranty coverage is provided in the United States of America and Canada.
WARRANTY COVERAGE
WARRANTY LIMITATIONS
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO
THE FULL EXTENT ALLOWED BY LAW.
NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable
to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not be responsible for
any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature or specifications furnished
by the Company.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above
limitations and exclusions may not apply to you.
The attached Warranty Registration Card MUST be filled out by the purchaser within thirty (30) days from purchase and mailed to Jacuzzi Whirlpool Bath
in order for this warranty to become effective.
EXCLUSION OF IMPLIED WARRANTIES
RETURN OF WARRANTY CARD
Jacuzzi Whirlpool Bath
P.O. Box 702168
Dallas, TX 75370-2168
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are
RESPONSIBILITIES OF OTHERS
responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer
of this responsibility. In the event of a problem, the unit must not be installed. The Company is not responsible for failures or damage that could
have been discovered, repaired, or avoided by proper inspection and testing prior to installation.
Damage occurring in transit is the responsibility of the carrier. The user or installer MUST open the crate and inspect the unit for damage when it is delivered.
If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure of the carrier to respond should
be reported to the seller and the carrier. Your freight claims should be filed promptly thereafter.
It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs relating to
obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.
Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the
responsibility of the user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (Options and accessories manufactured by the Company are
warranted for ninety (90) days from the original date of purchase for parts only.)
The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these requirements at the
time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state building codes in
U.S.A. or municipal or provincial codes in Canada.
For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such firms are not agents
WARRANTY SERVICE
or representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered
by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Representative of the nature of the
problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure
occurred or was discovered within the warranty period; an authorized independent service person or Company representative has been permitted to inspect the
unit during regular business hours within a reasonable time after the problem was reported by the user.
In order to obtain warranty service, consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service Agent. Describe
the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service.
If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:
To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied by the Company,
call or write the above. Provide a description of the problem and proof of purchase. You will be instructed how to obtain replacements and where to return, at
your expense, the failed component(s), option(s), or accessory(ies).
All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender terminates the
Company's warranty obligation.
Limited Warranty
Accessory(ies)
Ninety-Day
Parts Only
On
Jacuzzi Whirlpool Bath
Warranty Service Department
P.O. Box 702168
Dallas, TX 75370-2168
Call: 1-(800) 288-4002
Jacuzzi Whirlpool Bath© BY82000 03/05
Accessory(ies)
BY82000
Limited Warranty
Ninety-Day
Parts Only
On
6. What is the current market value of this property?
10.Approximately how long have you lived in this home? ___________
12.Was your purchase process?
13.How technically aware were you of the patented Jacuzzi® jet system
( ) $40,000 to $49,999 ( ) $150,000 and Above
( ) Very easy ( ) Easy ( ) Difficult ( ) Very Difficult
prior to your purchase?
( ) Not aware ( ) Somewhat aware ( ) Very aware
11.Please indicate, approximately, the total annual income of your
( ) 1 month - 2 months
household.
( ) Up to $24,999 ( ) $50,000 to $74,999
( ) $25,000 to $29,999 ( ) $75,000 to $99,999
( ) $30,000 to $39,999 ( ) $100,000 to $149,999
9. How long did you shop before purchasing unit?
( ) 1 day ( ) 2 months - 6 months
( ) 2 - 7 days ( ) 6 months - 1 year
( ) 1 week - 2 weeks ( ) 1 year - 2 years
( ) 2 weeks - 4 weeks ( ) +2 years
7. What is the age of the head of the household? ____________ years
8. What other manufacturers did you consider?
Please estimate $ _______________________________________
( ) Eljer ( ) Lasco ( ) Price Pfister ( ) Aqua Glass
( ) Kohler ( ) American Standard ( ) Sterling
( ) Other (Specify) _____________________________________
4. Who finally decided which product you would buy?
5. Who installed? ( ) Already installed/New Home
( ) Self ( ) Spouse ( ) Self and Spouse Together
( ) Other Family Member ( ) Designer/Architect
( ) Builder/Plumber/Remodeler ( ) Already Installed
( ) Contractor/Plumber when remodeling
( ) Self/Spouse when remodeling
( ) Other _____________________________________________
3. What was the main reason for purchase?
( ) Other _____________________________________________
( ) Styling ( ) Warranty Service ( ) Product Features
( ) Brand Name ( ) Price ( ) Hydrotherapy
( ) Home Resale _______________________________________
2. Who first gave you specific information about this product (specifications,
prices, etc.)?
( ) Dealer/Plumbing Supplier ( ) Builder ( ) Remodeler
( ) Plumbing Contractor ( ) Retailer/Home Center Store
( ) Decorator/Architect ( ) Already Installed
( ) Builder/Plumber/Remodeler ( ) Decorator/Architect
( ) Visited Retailer/Home Center Store
( ) Word of Mouth . . . Friend/Relative/Acquaintance
( ) Other (Please Describe) _______________________________
This card must be filled out and returned to the address printed on the other
side within thirty (30) days from date of purchase in order for this warranty to
be come effective.
Purchaser's Name _________________________________________
Purchaser's Address________________________________________
City _____________________________ State ______ Zip ________
Date of Purchase __________________________________________
Model Name ______________________________________________
Serial Number ____________________________________________
Dealer's Name ____________________________________________
Dealer's Address___________________________________________
1. How did you first hear about this Jacuzzi® product?
( ) Advertisement ( ) Article in Magazine/Newspaper
( ) Visited Dealer/Plumbing Supplier ( ) Yellow Pages
Warranty
Registration Card
Loading...