Jackson / Dalton Dishwasher AJ-66CE Service Manual

Download

Page 1

EE RR VV

AJ-66 SERIES RACK CONVEYOR DISHMACHINES

(ELECTRICALLY HEATED)

MODELS COVERED IN THIS MANUAL:

AJ-66CE AJ-66CEL

NN UU

March 7, 2001 P/N 7610-002-43-23 (Revision A)

www.jacksonmsc.com

Page 2

TABLE OF CONTENTS

SECTION DESCRIPTION PAGE

I. GENERAL SECTION

Specifications 1

II. INSTALLATION & OPERATION SECTION

Installation Instructions 2 Operation Instructions 3

AJ-66 Sequence of Operation 4 III. TROUBLESHOOTING SECTION 6 IV. DIMENSIONS

AJ-66 (Left to Right) Dimensions 8

AJ-66 (Right to Left) Dimensions 9 V. PARTS SECTION

AJ-66 Single Phase Control Box Assembly 10

AJ-66 Three Phase Control Box Assembly 12

Heater Box Assembly 14

Heater Box Covers/Thermostats 17

Wash Section Incoming Plumbing Assembly 18

Prewash Section Incoming Plumbing Assembly 19

Solenoid Valve Repair Parts 20

AJ-66 (Left to Right) Drain Plumbing Assembly 21

AJ-66 (Right to Left) Drain Plumbing Assembly 22

Drain Handle Weldment Assembly/Frame Weldment 23

Motors/Motor Support Bracket Assembly 24

Wash Pump Assembly 25

Wash Pump Weldment 26

Prewash Pump Weldment 27

Replacing Pump Gasket and Seal 28

Assorted Gaskets 29

Wash Heaters/Hood Weldments/Tub Weldments 30

Wash Manifold, Prewash Manifold & Strainer Support Weldments 31

Upper Wash Arm Assembly 32

Lower Wash Arm Assembly 33

Prewash Arm Assembly 34

Final Rinse Assembly 35

Drive Assembly 36

AJ-66 (Left to Right) Rack Rail Assembly 40

AJ-66 (Right to Left) Rack Rail Assembly 41

Actuator Assemblies 42

Wash Door and Vent Cowl Assembly 43

Miscellaneous Door Assemblies 44

Pawl Bar Roller Bracket 45

AJ-66 Pawl Bar Assembly 46

Miscellaneous Parts and Weldments 47

Strainers 50

Float Switch Assembly/Dress Panel 51

Curtains 52

Rinse Tray Assembly 53

208 Volt - 230 Volt, 60 Hz, Single Phase Schematic 54

208 Volt - 230 Volt, 60 Hz, Three Phase Schematic 55

460 Volt, 60 Hz, Three Phase Schematic 56

Page 3

SPECIFICATIONS

Page 4

INSTALLATION INSTRUCTIONS

Jackson MSC Inc. provides technical support for all of the dishmachines detailed in this manual. We strongly recommend that you refer to this manual before making a call to our technical support staff. Please have this manual with you when you call so that our staff can refer you, if necessary, to the proper page. Technical support is avaliable from 8:00 a.m. to 5:00 p.m. (EST), Monday through Friday. Technical support is not available on holidays. Contact technical support toll-free at 1-888-800-5672. Please remember that technical support is available for service personnel only. Non-service personnel should refer to the list of provided service agencies in this manual for local service support.

VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indicator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away the container. The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new, undamaged condition. However, rough handling by carriers or others may result in there being damage to the unit while in transit. If such a situation occurs, do not return the unit to Jackson; instead, contact the carrier and ask them to send a representative to the site to inspect the damage to the unit and to complete an inspection report.. You must contact the carrier within 48 hours of receiving the machine. Also, contact the dealer through which you purchased the unit.

UNPACKING THE DISHMACHINE: Once the machine has been removed from the container, ensure that there are no missing parts from the machine. This may not be obvious at first. If it is discovered that an item is missing, contact Jackson immediately to have the missing item shipped to you.

LEVEL THE DISHMACHINE: The dishmachine is designed to operate while being level. This is important to prevent any damage to the machine during operation and to ensure the best results when washing ware. The unit comes with adjustable bullet feet, which can be turned using a pair of channel locks or by hand if the unit can be raised safely. Ensure that the unit is level from side to side and from front to back before making any connections.

PLUMBING THE DISHMACHINE: All plumbing connections must comply with all applicable local, state, and national plumbing codes. The plumber is responsible for ensuring that the incoming water line is throroughly flushed prior to connecting it to any component of the dishmachine. It is necessary to remove all foreign debris from the water line that may potentially get trapped in the valves or cause an obstruction. Any valves that are fouled as a result of foreign matter left in the water line, and any expenses resulting from this fouling, are not the responsibility of the manufacturer.

CONNECTING THE DRAIN LINE: The drain for the models covered in this manual are gravity disharge drains. All piping from the 1-1/2” MNPT connection on the waste accumulator must be pitched (1/4” per foot) to the floor or sink drain. All piping from the machine to the drain must be a minimum 1-1/2” I.P.S. and shall not be reduced. There must also be an air gap between the machine drain line and the floor sink or drain. If a grease trap is required by code, it should have a flow capacity of 30 gallons per minute.

WATER SUPPLY CONNECTION: Ensure that you have read the section entitled “PLUMBING THE DISHMACHINE” above before proceding. Install the water supply line (3/4” pipe size minimum) to the dishmachine line strainer using copper pipe. It is recommended that a water shut-off valve be installed in the water line between the main supply and the machine to allow access for service. The water supply line is to be capable of 25 PSI “flow” pressure at the recommended temperature indicated on the data plate.

-ponent is not present on your machine. Do not confuse static pressure with flow pressure. Static pressure is the

line pressure in a “no flow” condition (all valves and services are closed). Flow pressure is the pressure in the fill line when the fill valve is opened during the cycle.

It is also recommended that a shock absorber (not supplied) be installed in the incoming water line. This prevents line hammer (hydraulic shock), induced by the solenoid valve as it operates, from causing damage to the equipment.

PLUMBING CHECK: Slowly turn on the water supply to the machine after the incoming fill line and the drain line have been installed. Check for any leaks and repair as required. All leaks must be repaired prior to placing the machine in operation.

ELECTRICAL POWER CONNECTION: Electrical and grounding connections must comply with the applicable portions of the National Electrical Code ANSI/NFPA 70 (latest edition) and/or other electrical codes.

Disconnect electrical power supply and place a tag at the disconnect switch to indicate that you are working on the circuit.

The dishmachine data plate is located on the right side and to the front of the machine. Refer to the data plate for machine operating requirements, machine voltage, total amperage load and serial number.

To install the incoming power lines, open the control box. Install conduit into the pre-punched holes in the back of the control box. Route power wires and connect to power block and grounding lug. Install the service wires (L1, L2, and L3 (3 phase only)) to the appropriate terminals as they are marked on the terminal block. Install the grounding wire into the lug provided. Tighten the connections. It is recommended that “DE-OX” or another similar anti-oxidation agent be used on all power connections.

VOLTAGE CHECK: Ensure that the power switch is in the OFF position and apply power to the dishmachine. Check the incoming power at the terminal block and ensure it corresponds to the voltage listed on the data plate. If not, contact a qualified service agency to examine the problem. Do not run the dishmachine if the voltage is too high or too low. Shut off the service breaker and mark it as being for the dishmachine. Advise all proper personnel of any problems and of the location of the service breaker. Replace the control box cover and tighten down the screws.

VENTILATION OF DISHMACHINE: The dishmachine should be located with provisions for venting into an adequate exhaust hood or ventilation system. This is essential to permit efficient removal of the condensation exhaust. Ensure that the exhaust system is acceptable in accordance with all applicable codes and standards.

NOTE: Damage caused by steam or moisture due to improper venti lation is NOT covered under the warranty.

This units covered in this manual have the following exhaust requirements: Load End: 200 CFM

Unload End: 400 CFM The exhaust system must be sized to handle this volume for the dishma-

chine to operate as it was designed to. ELECTRIC HEAT: The thermostats for the machines covered in this man-

ual are factory set. They should not be adjusted except by an authorized service agent.

In areas where the water pressure fluctuates or is greater than the recommended pressure, it is suggested that a water pressure regulator be installed. The models covered in this manual do not come with water pressure regulators as standard equipment. Please notify Jackson if this com

Page 5

INSTALLATION INSTRUCTIONS (CONTINUED)/OPERATING INSTRUCTIONS

CHEMICAL FEEDER EQUIPMENT: The AJ-66CEL is designed to operate with a third party chemical injection system. Jackson does not endorse any particular chemical injection system. The

system selected must be able to provide detergent and sanitizer in the required concentrations. The minimum chlorine concentration for proper sanitization is 50 PPM. Furthermore, the selected feeder needs to be able to operate against a head of 25 PSI and deliver 7.38 ml of a 10% chlorine sanitizer per minute.

Detergent may be introduced into the unit through the removal of the bulk head plug in the rear of the tub and replacing it with the third party detergent injection fitting. Remove the bulkhead plug in the side of the tub to install the detergent concentration probe.

For more information concerning detergent concerns, please refer to the page entitled “Detergent Control”.

The 1/8” brass plugs on the incoming plumbing rinse injector may be removed to install sanitizer and rinse aid injection fittings.

All wires for the chemical injectors should be routed through the back of the control box.

Terminals in the control box marked “CVS” provide a constant voltage signal whenever the drive motor is operating.

Terminals in the control box marked “DET” provide a voltage signal whenever the wash motor is operating.

DELIMING OPERATIONS: In order to maintain the dishmachine at its optimum performance level, it will be required to remove lime and corro sion deposits on a frequent basis. A deliming solution should be available from your detergent supplier. Read and follow all instructions on the label of the deliming solution.

To proceed with the deliming operation, fill the dishmachine and add the correct amount of deliming solution as recommended by the deliming solution manufacturer. The water capacity of the various tanks of the dishmachine can be verified on the specification sheet(s) of this manual.

Perform the following operations to delime the dishmachine:

1. Turn the NORMAL/DELIME switch on the back of the control box to the DELIME position.

2. Disconnect or turn off all chemical feeder pumps.

3. Close all doors (after adding the deliming solution).

4. Run the machine for the recommended period of time.

5. Turn the unit off and open the doors.

1. Close door(s) on dishmachine.

2. Close the drain valve(s).

POWER UP: To energize the unit, turn on the power at the service breaker. The voltage should have been previously verified as being correct. If not, the voltage will have to be verified.

FILLING THE WASH TUB: Ensure that the delime switch is in the NOR MAL position, and place the power switch into the ON position. The machine should fill automatically and shut off when the appropriate level is reached (just below the pan strainer). The wash tub must be completely filled before operating the wash pump to prevent damage to the component. Once the wash tub is filled, the unit is ready for operation.

WARE PREPARATION:Proper preparation of ware will help ensure good results and less re-washes. If not done properly, ware may not come out clean and the efficiency of the dishmachine will be reduced. It is important to remember that a dishmachine is not a garbage disposal and that simply throwing unscrapped dishes into the machine simply defeats the purpose altogether of washing the ware. Scraps should be removed from ware prior to being loaded into a rack. Pre-rinsing and pre-soaking are good ideas, especially for silverware and casserole dishes. Place cups and glasses upside down in racks so that they do not hold water during the cycle. The dishmachine is meant not only to clean, but to sanitize as well, to destroy all of the bacteria that could be harmful to human beings. In order to do this, ware must be properly prepared prior to being placed in the machine.

DAILY MACHINE PREPARATION: Refer to the section entitled “PREPA RATION” at the top of this page and follow the instructions there. Afterwards, check that all of the chemical levels are correct and/or that there is plenty of detergent available for the expected workload.

WASHING A RACK OF WARE: To wash a rack, simply slide a rack of soiled ware into the load end of the machine. Once the the machine is started, it should pull the rack through the machine and push it out the unload end. Once a rack has started through, you may put another rack in.

OPERATIONAL INSPECTION:Based upon usage, the pan strainers may become clogged with soil and debris as the workday progresses. Operators should reguarly inspect the pan strainers to ensure they have not become clogged. If the strainers do, they will reduce the washing capability of the machine. Instruct operators to clean out the pan strainers at regular intervals or as required by work load.

NOTE: On units equiped with prewash sections (AJ-66 and AJ-80), operators should also take the time to inspect the prewash section strainers and clean them as required by workload.

SHUTDOWN AND CLEANING: At the end of the workday, place the power switch in the OFF position and open the door(s). Open the drain valves and allow the machine to drain completely. Remove the pawl bar assembly (clean as required). Remove the

6. Wait five minutes, then inspect the inside of the machine. If the machine is not delimed, run another time cycle as per the deliming solution’s instructions.

7. When clean, drain and re-fill the machine.

8. Run in MANUAL for 10 minutes to remove residual deliming solution.

9. Drain and re-fill the machine.

OPERATING INSTRUCTIONS

PREPARATION:Before proceeding with the start-up of the unit, verify the

following:

pan strainers and, if equiped, the prewash strainers, run off sheets and scrap basket strainer. Remove the wash and, if equipped, the prewash arms and verify that the nozzles and arms are free from obstructions. Flush the arms with fresh water. Remove the pump suction strainers and clean out as required. Remove the rinse tray assembly and clean. Remove the curtains and scrub with a mild detergent and warm water. Wipe out the inside of the unit and then reassemble with the components previously removed.

Page 6

AJ-66 SEQUENCE OF OPERATION

REFER TO WIRING DIAGRAMS FOR ELECTRICAL FUNCTION AND REFERENCE DESIGNATIONS.

1. The prewash and wash tank doors are closed. A. Door switches (S2 and S3) close.

2. Power switch (S1) is turned to the “ON”. A. Power light (E1-Red) comes on.

3. Machine starts to fill automatically: A. Door safety switch (R9) is energized. B. Wash/Fill solenoid (WFS) and prewash fill solenoid (PWFS) valves open. C. Wash float switches (WFSW1 & WFSW2) close when correct water level is reached. D. Prewash float switches (PWFSW1 & PWFSW2) close. E. Wash tank fill relay (R7) and prewash tank fill relay (R8) are energized. F. Wash/Fill (WFS) and prewash (PWFS) solenoid valve close. G. Heat contactor (R1) is energized which activates wash tank heaters (H1).

4. Slide Dish Rack into machine: A. Prewash pump switch (S7) closes energizing prewash pump motor (R5) B. Drive motor contactor (R2) is energized starting the conveyor drive motor (M1) C. Prewash pump motor contactor (R5) closes starting prewash pump motor (M3) and drive motor contactor (R2).

5. As the dish rack moves into the wash tank area: A. Wash pump switch 1 (S4) closes energizing wash pump motor contactor (R3). B. Wash pump motor (M2) starts

6. As the dish rack continues to move through the wash tank. A. Prewash pump switch (S7) opens de-energizing prewash pump contactor (R5). B. Prewash pump motor (M3) stops. C. Wash pump switch 2 (S5) closes maintaining power to wash pump drive motor (R3) and conveyor drive motor con

-tactor (R2).

D. Wash pump switch (S4) opens

7. Dish rack moves into final rinse area: A. Final rinse switch (S6) closes energizing final rinse relay (R4) maintaining power to conveyor drive motor contactor

(R2). B. Contact closes energizing rinse solenoid (RS) and rinse aid signal relay (R6). C. R6 contact closes signaling rinse aid dispenser (provided by others). D. Wash pump switch 2 (S5) opens de-energizing wash pump motor contactor (R3). E. Wash pump motor (M2) stops.

8. Dish rack exits machine: A. Final rinse switch (S6) opens. B. Final rinse relay (R4) is de-energized. C. R4 contact opens de-energizing final rinse solenoid (RS) and rinse aid signal relay (R5). D. Drive motor contactor (R2) is de-energized which stops conveyor drive motor (M1).

9. If dish racks are fed into the dishwasher continuously the foregoing sequence of operation will continue In this type of operation

all devices required to wash the ware will continue without stopping.

10. If the water level in the wash tank falls too low: A. The wash float switch 2 (WFSW2) opens. B. Wash tank fill relay (R7) is de-energized. C. Heat contactor (R1) is de-energized. D. Wash heater (H1) is de-energized. E. Wash fill solenoid (WFS) opens allowing water to fill tank. When water level reaches correct height. F. Wash float switch 1 (WFSW1) closes. G. Wash tank fill relay (R7) is energized. H. Heat contactor (R1) is energized. I. Wash heater (H1) is energized. J. Wash fill solenoid valve (WFS) closes.

Page 7

AJ-66 SEQUENCE OF OPERATION (CONTINUED)

The foregoing cycle will continue whenever the water level in the wash tank falls below optimum operating level. As long As the dishwasher is in operation the water level will be maintained.

11. If the water level in the Prewash tank falls below preset operating level: A. The prewash float switch 2 (PWFSW2) opens. B. Prewash tank fill relay (R8) is de-energized. C. Prewash fill solenoid (PWFS) opens allowing water to fill tank when the water level reaches correct height. D. Prewash float switch 1 (PWFSW1) closes. E. Prewash tank fill relay (R8) is energized. F. Wash fill solenoid valve (PWFS1) closes.

The foregoing cycle will continue whenever the water level in the prewash tank falls below optimum operating level. As long as the dishwasher is in operation the water level will be maintained.

12. Door safety switches (S2 or S3) will de-energize all hazardous functions whenever the doors are opened. Operation will resume

when doors are closed.

A. Door safety switch (S2 or S3) opens de-energizing the following:

• Door safety switch relay (R9).

• Drive motor contactor (R2).

• Wash pump motor contactor (R3)

• Final rinse relay (R4).

• Prewash pump contactor (R5).

B. When this occurs all machine functions except wash and prewash tank fills plus wash heater (H1) are stopped until

door(s) are closed.

C. Unit will automatically resume operation when the door(s) are closed.

13. (If the unit is equipped with an optional cold water thermostat) The water temperature in the prewash tank will be maintained at

between 110 to 140 degrees F. through the cold water thermostat.

A. When water temperature goes above 140 degrees F. the cold water thermostat (CWTS) opens. B. The cold water valve (CWV) is de-energized allowing cold water into the prewash tank. C. When the pre-set temperature is reached the cold water thermostat (CWTS) closes. D. Cold water valve (CWV) is energized shutting off the cold water to the prewash tank.

14. If the unit is equipped with a table limit switch (TLS). This item is mounted on the unload (clean) table edge to shut-down the

dishwasher when tripped by the racks of clean dishes.

A. Table limit switch (TLS) opens B. The following controls are de-energized:

• Door safety switch relay (R9).

• Drive motor contactor (R2).

• Wash pump motor contactor (R3).

• Final rinse relay (R4).

• Prewash pump contactor (R5).

C. When the above controls are de-energized all machine functions except wash heater (H1), wash and prewash tank

fill valves are stopped until the rack(s) are removed from the unload (clean) table.

D. Dishwasher will automatically resume operation when the rack(s) are removed.

Page 8

TROUBLESHOOTING SECTION

Problem: Nothing on dishmachine operates. The power switch is ON and the power indicator light is OFF.

Possible causes:

1. Machine is not wired correctly to incoming power source. Have an electrician verify wiring.

2. Machine circuit breaker is tripped. Reset the circuit breaker. If it trips again, contact an electrician to verify the machine amp draw.

3. Service breaker is tripped. Reset the service breaker. If it trips again, contact an electrician to verify the machine amp draw.

Problem: Machine will not fill. The power switch is ON and the power indicator light is ON.

Possible causes:

1. No water supply to machine. Verify that water lines have been connected to the machine.

2. Dishmachine doors are not closed. Close doors completely.

3. Incoming water solenoid valve damaged/faulty. Verify that the valve is operating. If not, replace.

4. Tank floats faulty. Verify the wiring of the floats. Verify that no debris is jamming the floats. Replace if necessary.

Problem: Machine fills, but fill is weak.

Possible causes:

1. Low incoming water pressure. Verify that incoming water pressure during fill is 20 PSI.

2. Incoming water solenoid is clogged. Verify that debris is not entrapped in valve. If so, remove debris.

Problem: Low wash tank temperature.

Possible causes:

1. Low incoming water temperature. Verify that the incoming water temperature matches what is indicated on the machine data plate.

2. Heater not energizing. Verify that the wash tank heater is operating. If not, replace.

3. Low incoming voltage. Have an electrician verify that the power coming to the machine is the same as indicated on the data plate.

Problem: Low wash arm pressure, poor spray pattern.

Possible causes:

1. Clogged wash arm nozzles. Verify that nozzles are not clogged with debris. If so, remove debris.

2. Clogged wash tank or wash pump strainers. Clean out strainers if necessary.

3. Worn wash pump impeller. Verify status of impeller, replace if necessary.

Problem: Low prewash arm pressure, poor spray pattern.

Possible causes:

1. Clogged prewash arm nozzles. Verify that nozzles are not clogged with debris. If so, remove debris.

2. Clogged prewash tank or prewash pump strainers. Clean out strainers if necessary.

3. Worn prewash pump impeller. Verify status of impeller, replace if necessary.

Problem: Inadequate rinse.

1. Low incoming water pressure. Verify that incoming water pressure during fill is 20 PSI.

2. Incoming water solenoid is clogged. Verify that debris is not entrapped in valve. If so, remove debris.

Problem: Pawl bar moves with no load, but does not move when loaded.

1. Clutch on drive assembly is out of adjustment. Adjust as required.

Problem: Pawl bar does not move.

1. Failed or broken overload spring. Replace spring if necessary.

2. No power to the drive motor/failed drive motor. Verify power and wiring connections to the motor. If necessary, replace the motor.

3. Pawl bar not properly installed. Verify that the pawl bar is installed correctly.

Page 9

TROUBLESHOOTING SECTION (CONTINUED)

Problem: Racks go through the machine, but results are poor.

1. Verify that detergent is being dispensed into the machine at the appropriate quantities for the water volume. If not, get detergent to

appropriate level and review results of washing ware.

2. Clogged strainers/scrap basket. Clean out strainers and scrap basket and replace.

3. Ware not being properly prescrapped. Review paragraph entitled ‘Ware Preperation” in Operating Instructions.

4. Wash or rinse arms missing end plugs or caps. Verify and replace as required.

5. Low tank heat (see previous page).

6. Inadequate rinse (see previous page).

7. Incorrect voltage coming to the machine. Verify that the voltage matches that on the machine data plate.

8. Wash pump cavitation due to low water level. Verify that the drains are shut and that the water level is correct.

Problem: Sotting of silverware, glasses and dishes.

1. Incorrect final rinse temperature. Verify that the rinse water temperature matches that which is listed on the machine data plate.

2. Clogged wash and/or rinse nozzles and arms. Remove the arms and verify that they and their nozzles are from debris.

3. Excessively hard water. Install a water softener to reduce hardness.

4. Loss of water pressure due to clogged/obstructed wash pump. Turn the power off to the machine at the source. Drain the wash tank

of water and verify that the pump intake is free from debris.

5. Improper scrapping procedures. Review the paragraph entitled “Ware Preperation” in Operating Instructions.

6. incorrect detergent/chemcial concentrations. Verify that the detergent/chemical concentrations are correct for the associated water

volume.

TORQUE SETTINGS

When replacing components either in the control box or the heater box area, the manufacturer has suggestions on how much to torque the screws and nuts used in securing items to the machine. Refer to the table below for the torque specifictions:

ITEMS TORQUE SPEC

Relays 16 In/lbs Heater Contactor 35 In/lbs Heater Nuts 16 In/lbs Terminal Block 50 In/lbs

Page 10

AJ-66 (LEFT TO RIGHT) DIMENSIONS

LEGEND: A - INCOMING WATER

HOOKUP

B- PREWASH INCOMING PLUMBING

HOOKUP

Page 11

AJ-66 (RIGHT TO LEFT) DIMENSIONS

LEGEND: A - INCOMING WATER

HOOKUP

B- PREWASH INCOMING PLUMBING

HOOKUP

Page 12

3, 4, 5

4, 9, 10

AJ-66 SINGLE PHASE CONTROL BOX ASSEMBLY

4, 7, 10, 11, 12

10, 18

21, 22

21, 23

13, 21

19, 20

Page 13

AJ-66 SINGLE PHASE CONTROL BOX ASSEMBLY (CONTINUED)

ITEM QTY DESCRIPTION MFG No.

1 1 Electrical Box Weldment 5700-041-88-50 2 1 Decal, L1-L2-L3 9905-101-12-66 3 1 Terminal Block 5940-011-48-27 4 6 Lockwasher, #10 5311-273-02-00 5 2 Screw, 10-32 x 3/4" Long Phillips Trusshead 5305-011-62-17 6 1 Light, Amber 5945-111-44-44 7 1 Wire Lug, 2 AWG to 14 AWG 5940-200-76-00 8 1 Light, Red 5945-111-44-45

MISCELLANEOUS PARTS NOT SHOWN: Grommet, 1/2” OD x 3/8” ID 5325-011-46-73

Bushing, Heyco SB100 5975-210-09-00 Plug, Heyco 2700 G-875 5975-011-47-81 Control Box Cover 5700-031-89-42 Control Box Cover Hinge Weldment 5700-021-68-57 Control Hinge Rod 5700-011-68-58 Washer, Flat, S/S, 1/4” ID 5311-174-01-00 Cotter Pin 5315-011-68-56 MANUAL/DELIME Switch (located on rear of control box) 5930-301-22-18 MANUAL/DELIME Switch Decal (located on rear of control box) 9905-011-74-61 Copper Conductors Only Decal 9905-011-47-35 Control Box Leg 5700-011-71-47 Bolt, 1/4”-20 x 2-1/2” Long Hex Head 5306-011-83-52 Locknut, 1/4”-20 with Nylon Insert 5310-374-01-00 Component Mounting Plate (located inside the control box) 5700-031-67-03

Page 14

3, 4, 5

4, 9, 10

AJ-66 THREE PHASE CONTROL BOX ASSEMBLY

4, 7, 10, 11, 12

20, 21

24, 25, 26

26, 27

22, 23

26, 27

26, 28

13, 26

26,32

Page 15

AJ-66 THREE PHASE CONTROL BOX ASSEMBLY (CONTINUED)

ITEM QTY DESCRIPTION MFG No.

1 1 Electrical Box Weldment 5700-041-88-50

2 1 Decal, L1-L2-L3 9905-101-12-66

3 1 Terminal Block 5940-011-48-27

4 6 Lockwasher, #10 5311-273-02-00

5 2 Screw, 10-32 x 3/4" Long Phillips Trusshead 5305-011-62-17

6 1 Light, Amber 5945-111-44-44

7 1 Wire Lug, 2 AWG to 14 AWG 5940-200-76-00

8 1 Light, Red 5945-111-44-45

9 1 Din Rail 5700-021-72-75 10 3 Screw, 10-32 x 1/2" Long Phillips Trusshead 5305-011-39-36 11 1 Washer, Flat, 1/4" ID 5311-174-01-00 12 1 Decal, Ground 9905-011-86-86 13 1 Terminal Board 5940-021-70-70 14 3 Motor Contactor 5945-111-68-38 15 1 Circuit Breaker (208/230 Volt Models Only) 5925-011-68-34 16 1 Overload (2.5 - 4 RTIK) 5945-111-68-41 17 1 Switch, ON/FILL & OFF/DRAIN 5930-011-49-55 18 1 Overload (5.5 - 7.5 RTIM) 5945-111-68-40 19 1 Overload (1.0 - 1.5 RTIG) 5945-111-68-39 20 1 Heater Contactor 5945-002-24-70 21 2 Screw, 10-32 x 3/8" Long Phillips Trusshead 5305-173-12-00 22 1 Transformer 5950-011-68-35 23 4 Locknut, 10-24 with Nylon Insert 5310-373-01-00 24 1 Fuse Holder (460 Volt Models Only) 5920-011-72-89 25 1 Fuse (460 Volt Models Only) 5920-011-72-88 26 12 Screw, 6-32 x 3/8" Long Phillipshead 5305-171-02-00 27 3 Control Relay 5945-111-35-19 28 1 Relay 5945-111-72-51 29 1 Thermometer, 48" Lead 6685-111-68-48 30 2 Thermometer, 96" Lead 6685-111-68-49 31 1 Decal, AJ-66 Gauge 9905-021-72-30 32 1 Terminal Board 5940-021-89-41

MISCELLANEOUS PARTS NOT SHOWN: Grommet, 1/2” OD x 3/8” ID 5325-011-46-73

Page 16

13, 15

HEATER BOX ASSEMBLY

AJ-66 TUB

12, 14

3, 4, 5

12, 14

1, 2

10, 11

Page 17

HEATER BOX ASSEMBLY (CONTINUED)

ITEM QTY DESCRIPTION MFG No.

1 1 See Page Entilted "Wash Heaters" N/A 2 1 Heater Gasket 5330-200-02-70 3 6 Washer, Flat, 5/16" 5311-175-01-00 4 6 Lockwasher, 5/16" 5311-275-01-00 5 6 Nut, 5/16"-18 5310-275-01-00 6 1 Thermostat, Wash Regulating 5930-121-67-72 7 1 Thermostat, High Limit Control 5930-121-71-36 8 1 Float Switch (Wash Tank) 6680-121-70-71

9 1 Float Switch (Prewash Tank) 6680-121-70-16 10 1 Heater Box Weldment (AJ-44 Only) 5700-031-66-81 10 1 Heater Box Weldment (AJ-66/AJ-80 Only) 5700-031-71-66 11 6 Locknut, 1/4"-20 with Nylon Insert 5310-374-01-00 12 3 Reed Switch (All Models) 5930-111-68-44 13 1 Reed Switch (AJ-66 and AJ-80 Models Only) 5930-111-68-44 14 3 Reed Switch Bracket (All Models) 5700-021-71-18 15 1 Reed Switch Bracket (AJ-66 and AJ-80 Models Only) 5700-021-71-18

The wash tank heater system is electrically connected in the circuit so that they are dependent upon the dishwasher being properly filled with and maintaining a safe water level, two thermostats (mounted in the heater box behind the dress panel), float switch (mounted in the wash tank), and the heater relay (mounted in control box) with the heater being activated by the thermostats.

Once the dishwasher has been filled to the correct level, the heater should operate automatically. Should the tank heat be too high, too low or no indication of temperatures at all, the following checkout should be made.

Note: The following checkout should be made by either a qualified service person or electrician. A.- Checkout of the heater system

1.- If the temperature is too high, adjust thermostat using instructions on the page entitled “Thermostats”.

2.- If temperature is too low, adjust thermostat as above, then: a.- Turn off power to machine by placing customer’s circuit breaker in the “OFF” position. Turn off machine circuit

breaker located on right side of control box. b.- Remove cover from control box on top of dishwasher. c.- Make sure water temperature is below 140 degrees F.(preferably about 130 degrees F.). d.- Turn on both circuit breakers. Observe heater relay (R1) while the power switch is turned “ON” and “OFF”. If relay

contacts move in and out, the heater relay is operating correctly: if not proceed to ”C”.

B.- If heater relay (R1) closes:

1.- Check power supply at incoming terminal board L1, L2 & L3. It should be the same voltage as indicated on the machine data plate.

2.- Check power at connections on heater relay (R1). The voltage should agree with the voltage on the machine data plate. If not, check wires for breaks or bad connections.

3.- Check power at terminals of heater which should agree with the data plate. If not check wires for breaks or bad con

-nections.

4.- Temperatures should rise as explained in “C-1”, and amperage may be checked according to those instructions. Replace any defective elements.

C.- If heater relay (R1) does not close.

1.- There is an insulated movable insulated movable bar on relay across the top. With an insulated probe, depress this bar and observe the thermometer: the temperature should rise noticeably in a minute or two. If it moves slowly, it would indicate that the element is faulty. If it moves constantly higher at a good rate, elements should be good.

Note: A check with an amp probe at heater relay (R1) terminals should be made to verify the amp draw on each leg. This should be appropriate for the voltage and phase indicated on the data plate.

Page 18

HEATER BOX ASSEMBLY (CONTINUED)

ITEM QTY DESCRIPTION MFG No.

1 1 Terminal Board 5940-021-70-70 2 2 Locknut, 6-32 with Nylon Insert 5310-373-03-00 3 1 Thermostat Bracket 5700-011-73-72

HEATER PROTECTION & AUTOMATIC FILL

This control is activated when the power switch is turned “ON”. The primary function is to automatically energize the wash tank heat circuit. It will also cutoff the wash tank heat circuit should the water be accidently drained from the machine with the power switch still “ON”. The power switch should always be turned-off before draining the unit.

This water level control consists of two (2) floats that operate when the power switch is turned on and works in conjunction with the thermostats and heater relays.

When the power switch is turned “ON” water starts to enter the dishmachine. When it reaches the proper level the normally open contacts in the water level float switch close activating the heating circuit for tank heat.

If the water level below the correct level while power is still on, the float switch will sense the lack of water and de-activate the heater.

Page 19

THERMOSTATS:

HEATER BOX COVER/THERMOSTATS

AJ-66 Heater Box Cover

5700-031-71-70

Secured with Screw, 10-32 x 3/8” Long Phillips Trusshead

5305-173-12-00

This unit has a probe-direct sensing type thermostat with fixed set point and adjustable range for both wash and booster tank heat regulating. The same type thermostat is used as the high limit sensor for the wash tank heater. It operates a precision single double throw switch through a lever for close tolerance narrow differential switching capability. The unit has screw driver adjustment and front connect terminals and is mounted by 7/16”-24 thread, Loxit fitting for easy removability and serviceability.

The thermostat range is from 140 to 240 degrees F. with a maximum bulb exposure temperature of 300 degrees F. Unit is listed at 12.5 amps at 24/120 VAC.

There are two (2) thermostats on the dishwasher. One monitors the wash tank temperature, the second monitors the rinse water temperature. Although all are identical in appearance there are different replacement part numbers depending on the function of the thermostat.

Calibration:

Wash Thermostat:

Set Point --165 degrees F. Adjustable range.

Hi-LImit Thermostat:

Fixed set point--210 degrees F. non-adjustable

The hi-limit thermostat is used to protect the heater element in the event of a run away regulating thermostat or a dry fire situation. It is set for 210 degrees F. +0 or -10 degrees F. with a fixed set point. This part is not adjustable.

The wash tank regulating thermostat will maintain the correct wash water temperature to meet NSF requirements. These specify that the wash be no lower than 160 degrees F. It is set at the factory to energize the tank heater at 165 degrees F. and de-energze at 177 degrees F.

The rinse tank regulating thermostat will maintain the correct rinse water temperature to meet NSF requirements. It is factory set to energize the rinse tank heater at 195 degrees F. and de-energize at 200 degrees F.

To order decals that go with the thermostats: Decal, Thermostat Regulating 9905-011-84-31

Decal, High Limit 9905-011-84-32

Page 20

WASH SECTION INCOMING PLUMBING ASSEMBLY

121Tube, Copper, 3/4" x 2.63"

5700-011-72-71

2 3

4 8 6

7 8

17 6

13 3

ITEM QTY DESCRIPTION MFG No.

1 1 Rinse Injector Manifold Weldment 5700-021-67-98 2 3 Plug, Brass, 1/8" NPT 4730-209-07-37 3 2 Vacuum Breaker, 3/4" NPT 4820-300-08-00 4 3 Elbow, Street, 3/4" NPT 4730-206-04-34 5 1 Plug 4730-209-01-00 6 2 Union, Brass, 3/4" 4730-212-05-00 7 2 Solenoid Valve, 3/4" 4810-100-53-00 8 4 Nipple, Close, Brass, 3/4" NPT 4730-207-34-00

9 2 Fitting, 3/4" Male to Slip Copper 4730-401-11-01 10 1 Tube, Copper, 3/4" x 3.44" 5700-011-72-70 11 1 Fill Injector 5700-011-67-99

21 12

18 18 9

Page 21

WASH SECTION INCOMING PLUMBING ASSEMBLY (CONTINUED)

71Nipple, Brass, 6" Long

5700-001-26-74

13 1 Gauge, Pressure, 0-100 PSI 6685-111-59-66 14 1 Valve, Ball, Test Cock, 1/4" NPT 4810-011-72-67 15 1 Tube, Copper, 3/4" x 3" 5700-000-54-85 16 2 Tee, 3/4" x 1/2" x 3/4" 4730-411-03-01

2 Adapter, 1/2" to 1/4" FNPT 4730-401-41-01

17 1 Elbow, Brass, 90 Degree, 3/4", Copper 4730-406-42-01 18 2 Tube, Copper, 3/4" x 2-13/16" 5700-011-72-72 19 1 "Y"-Strainer, 3/4" 4730-717-02-06 20 1 Nipple, Brass, 6" Long 5700-001-26-74 21 1 Tee, 3/4", CU x CU x CU 4730-411-46-01

PREWASH SECTION INCOMING PLUMBING ASSEMBLY

1 2

ITEM QTY DESCRIPTION MFG No.

1 1 "Y"-Strainer, 3/4" 4730-717-02-06

2 2 Nipple, Close, Brass, 3/4" NPT 4730-207-34-00

3 1 Solenoid Valve, 3/4" 4810-100-53-00

4 1 Fill Injector 5700-011-67-99

5 2 Elbow, Street, 3/4" 4810-100-53-00

6 1 Vacuum Breaker, 3/4" 4820-300-08-00

3 2 5

Page 22

Data Plate

Valve Bonnet

Diaphragm

Retainer

SOLENOID VALVE REPAIR PARTS

Screw

Spring position is moved for clarity. Goes below Item 3.

Screen Retainer

Valve Body

Order the entire solenoid valve using part number 4810-100-03-18.

Mesh Screen

ITEM QTY DESCRIPTION MFG No.

1 1 Coil, 3/4" Valve, 220 Volt 4810-200-02-18 2 1 Spring 4810-200-04-18 3 1 Plunger 4810-200-04-18 4 1 O-Ring 4810-100-10-18 5 1 Diaphragm 4810-100-10-18

Page 23

AJ-66 (LEFT TO RIGHT) DRAIN PLUMBING ASSEMBLY

1Entire Assembly

5700-041-69-71

1 1

9 10910

ITEM QTY DESCRIPTION MFG No.

1 6 Adapter, Male to Female, 1-1/2" 4730-401-25-01 2 3 No Hub Connector 4720-604-06-00 3 3 Tee, Brass, 1-1/2" FNPT x 1-1/2" FNPT x 1-1/2" FNPT 4730-011-69-93 4 2 Valve, Ball, 1-1/2" FNPT 4820-011-71-46 5 2 Nipple, Brass, Close, 1-1/2" NPT 4730-207-40-00 6 2 Elbow, Brass, 90 Degree, 1-1/2" FNPT 4730-011-73-77 7 1 Elbow, Brass, Street, 1-1/2" NPT 4730-206-32-00 8 1 Rinse Nipple Weldment 5700-021-84-61

9 2 Tube, Copper, 1-1/2" x 4-3/4" Long 5700-011-70-08 10 2 Tube, Copper, 1-1/2" x 4-1/4" Long 5700-011-70-07 11 2 Tube, Copper, 1-1/2" x 8-1/4" Long 5700-021-70-06 12 1 Nipple, Brass, 1-1/2" NPT x 3" Long 4730-011-87-04 13 2 Valve Handle Weldment Assembly 5700-021-84-74

4 4

Page 24

AJ-66 (RIGHT TO LEFT) DRAIN PLUMBING ASSEMBLY

3 3

2 2

8 8

4 45

7 7

3 3 3

ITEM QTY DESCRIPTION MFG No.

1 1 Elbow, 1-1/2" NPT, Brass, Street 4730-206-32-00 2 2 Valve, Ball, 1-1/2" FNPT 4820-011-71-46 3 6 Adapter, Male to Female, 1-1/2" 4730-401-25-01 4 2 Tube, Copper, 1-1/2" x 4-1/4" Long 5700-011-88-40 5 3 Tee, Brass, 1-1/2" x 1-1/2" x 1-1/2" 4730-011-69-93 6 2 Nipple, Brass, 1-1/2" NPT, Close 4730-207-40-00 7 2 Tube, Copper, 1-1/2" x 4-3/16" Long 5700-021-70-08 8 2 Tube, Copper, 1-1/2" x 8-1/8" Long 5700-021-70-06

9 2 Elbow, 1-1/2" FNPT, 90 Degree, Brass 4730-011-73-77 10 3 Connector, No Hub, 1-1/2" 4720-604-06-00 11 1 Nipple, Brass, 1-1/2" NPT x 3" Long 4730-011-87-04 12 1 Rinse Nipple Weldment 5700-021-84-61 13 2 Valve Handle Weldment Assembly 5700-021-84-74

1 Entire Assembly 5700-031-75-00

Page 25

DRAIN HANDLE WELDMENT ASSEMBLY/FRAME WELDMENT

ITEM QTY DESCRIPTION MFG No.

1 1 Ball Valve Handle Weldment 5700-021-70-45 2 1 Locknut, 1/4"-20 with Nylon Insert 5310-374-01-00 3 1 Spacer 5700-000-01-52 4 1 Screw, 1/4"-20 x 2" Long Hex Head 5306-011-84-72

1 Entire Assembly 5700-021-84-74

Item 1: Model Left to Right P/N Right to Left P/N AJ-66CE/CEL 5700-002-32-01 5700-031-68-09 Item 2: Bullet Feet (4 per model) - order using part number 5340-011-71-74.

FRAME WELDMENT

Page 26

MOTORS/MOTOR SUPPORT BRACKET ASSEMBLY

1Entire Assemby

5700-021-73-42

Start

Capacitor

Single Phase Motor

The chart below details the part numbers for the various models covered in this manual. Refer to the machine data plate for voltage and phase information.

Model Volts Phase Prewash Motor P/N Wash Motor P/N Drive Motor P/N AJ-66CE/CEL 208 1 6105-021-70-55 6105-021-70-57 6105-121-70-53

AJ-66CE/CEL 230 1 6105-021-70-55 6105-021-70-57 6105-121-70-53 AJ-66CE/CEL 208 3 6105-121-70-56 6105-121-70-58 6105-121-70-54 AJ-66CE/CEL 230 3 6105-121-70-56 6105-121-70-58 6105-121-70-54 AJ-66CE/CEL 460 3 6105-121-70-56 6105-121-70-58 6105-121-70-54

The clamp used to secure the pump motor to the bracket may be ordered using part number 4730-002-32-15.

The locknuts (1/4”-20 Hex with Nylon Insert) used to secure the assembly to the tub bottom may be ordered using part number 5310-374-01-00.

Three Phase Motor

ITEM QTY DESCRIPTION MFG No.

1 1 Upper Pump Support Bracket Weldment 5700-021-73-68 2 1 Lower Pump Support Bracket Weldment 5700-021-73-71 3 1 Nut, Serrated, 1/4"-20, Hex 5310-011-66-49

Page 27

WASH PUMP ASSEMBLY

152Hose Clamp, 1-1/16" - 2"

4730-719-18-00

ITEM QTY DESCRIPTION MFG No.

1 1 See Page Entitled "Pump Support Bracket Assembly" N/A

2 1 Hose Clamp, 4-1/8" - 7", HSS104 4730-002-32-15

3 1 See Page Entitled "Motors" N/A

4 4 Nut, Hex, 3/8"-16, S/S 5310-276-01-00

5 1 Pump Plate 5700-021-71-83

6 1 Pump Seal 5330-011-71-98

7 4 Bolt, 3/8"-16 x 2" Long Hex Head 5305-011-74-98

8 1 Key, 3/16" x 1" Long 5700-011-89-17

9 1 Impeller (Wash) 5700-031-67-45 10 1 Impeller Washer 5700-011-71-95 11 1 Bolt, 1/4"-20 x 3/4" Long Hex Head 5305-274-04-00 12 1 Pump Manifold Hose 5700-002-18-17 13 1 See Page Entitled "Assorted Gaskets" N/A 14 1 See Page Entitled "Wash Pump Weldment" N/A

Page 28

WASH PUMP WELDMENT

Intake Suction Scoop Weldment

5700-021-87-60

The wash pump weldment is a single part. Separate pieces of the weldment are not available for purchase. The weldment is used for the wash pump in all models covered in this manual. The weldment may be ordered using part number 5700-041-68-88.

The gasket used to seal the weldment to the tub can be found on the page entitled “Assorted Gaskets”. The pump weldment is secured to the pump plate (through the actual tub wall) using the following fasteners:

Nut, Hex, 3/8”-16 P/N 5310-276-01-00 Washer, Flat, 3/8” P/N 5311-176-01-00 Lockwasher, Split, 3/8” P/N 5311-276-01-00

Please refer to the page entitled “Ordering Replacement Fasteners” for information concerning Jackson’s policy on minimum order quantities.

The pump weldment, gasket, and associated fasteners are not available as one assembly and must be ordered separately.

Page 29

PREWASH PUMP WELDMENT

To order the prewash strainer support bracket, refer to the pages enti tled “Miscellaneous Parts and Weldments”. Refer to part number 5700-021-74-94 for information concerning the bracket and the hardware used to secure it to the prewash pump weldment

Prewash Intake Strainer Weldment

5700-021-74-96

The prewash pump weldment is a single part. Separate pieces of the weldment are not available for purchase. The weldment is used for the wash pump in all models covered in this manual. The weldment may be ordered using part number 5700-002-10-62.

Nut, Hex, 3/8”-16 P/N 5310-276-01-00 Washer, Flat, 3/8” P/N 5311-176-01-00 Lockwasher, Split, 3/8” P/N 5311-276-01-00

Please refer to the page entitled “Ordering Replacement Fasteners” for information concerning Jackson’s policy on minimum order quantities.

The pump weldment, gasket, and associated fasteners are not available as one assembly and must be ordered separately. For a detailed breakdown of the prewash pump, refer to the page entitled “Wash Pump Assembly”. The differences between the wash

pump breakdown shown on that page and the prewash pump assembly are as follows: Item 9: The impeller for the prewash pump is ordered using part number 5700-031-71-78.

Item 12: The hose for the prewash pump is ordered using part number 5700-011-22-92. Item 14: The prewash pump weldment is ordered as per the instructions given above.

Page 30

REPLACING PUMP GASKET AND SEAL

The AJ series dishwashers utilize an internal self-draining pump and motor assembly. The motor shaft seal is located between the impeller and the motor mounting plate. The pump gasket is located between the motor mounting plate and the wall of the wash tank. The internal pump housing is assembled inside the wash tank with the mounting studs extended through the wall of the wash tank. The stud are used to mount the pump assembly to the pump housing.

A. Replacement of gasket and/or pump seal.

1. Remove the Power Source to the dishwasher by turning the customer’s circuit breaker or fused disconnect switch to the

“OFF” position.

2. Drain the dishwasher by opening the drain valve. NOTE: If the motor must be moved to a bench or table remove the wiring and conduit connections. If the motor is to remain attached to the machine, have a sturdy stand to support the motor after it is removed from the pump. Proceed

to step 3.

3. Remove the four (4) nuts holding the mounting plate in position.

4. Remove the band clamp holding the end of the motor.

5. Carefully pull the motor and mounting plate assembly outward, move the motor from side to side as you pull, this will help it to release from the tank wall. Set the motor on a stand or something solid to support the motor while working on it.

6. Remove and replace the gasket. (If pump seal is leaking move to step 7.)

7. Insert a large flat tip screwdriver into the blades of the impeller and use to hold the impeller so it does not turn. Use a wrench or socket with ratchet to remove the bolt in the end of the motor shaft. Lay the bolt and washer aside and pull the impeller up and off the shaft. (Be careful not to loose the woodruff key holding the impeller.) Set the impeller and woodruff key aside.

8. Remove the four (4) bolts holding the motor to the mounting plate.

9. Slide the mounting plate off the motor shaft, the pump shaft seal will come off with the mounting plate. Note: The pump shaft seal will have the following parts: A. A rubber seal with a ceramic ring set inside it, that will seat in the center of the mounting plate.

B. A rubber seal with a stainless steel outside, that seals the motor shaft and seats against the ceramic ring. C. A spring to support the impeller from the under side. D. A stainless steel spring cap to capture the top of the spring and hold it in place.

10. Turn the mounting plate over and push the rubber seal and ceramic out of the center, then turn the mounting plate back over.

11. Clean the hole where the seal and ceramic were removed.

12. Place the mounting plate back on the motor and install the four (4) bolts that attach the motor.

13. Lightly coat the seals with lubricant or dip in a soapy type liquid. Gently press the new seal and ceramic over the shaft and slide down into the mounting plate hole. Gently slide the shaft seal over the shaft and down against the mounting plate seal. Place the spring and cap down over the shaft.

14. Place the woodruff key back into the groove of the motor shaft and install the impeller, being careful to align the woodruff key with the slot in the impeller. Replace the bolt and washer and tighten.

15. Install the motor by placing it on the studs and sliding it forward until it is against the wash tank wall. Replace the nuts and washers, then tighten.

16. Replace the band clamp on the motor end and support bracket.

Page 31

ASSORTED GASKETS

Motor Mounting Gasket, P/N 5330-011-71-62

Rinse Assembly Vellumoid Gasket, P/N 5330-111-42-81

Heater Gasket, P/N 5330-200-02-70

Rinse Drain Plate Gasket, P/N 5330-011-72-27Pawl Bar Gutter Gasket, P/N 5330-011-68-55

Page 32

WASH HEATERS/HOOD WELDMENTS/TUB WELDMENTS

Order your wash heaters using the table below:

Model Volts Phase KW Part Number AJ-66CE/CEL 208 1 15 4540-121-68-45

AJ-66CE/CEL 230 1 15 4540-121-68-46 AJ-66CE/CEL 208 3 15 4540-121-68-45 AJ-66CE/CEL 230 3 15 4540-121-68-46 AJ-66CE/CEL 460 3 15 4540-121-68-47

The models covered in this manual each have different tub and hood weldments. The weldments, when ordered, do not come with any parts that attach separately to the machine (for example, curtain hooks in the case of the hood weldments are a seperate item and must be ordered independently of the hood weldments). To order these components, refer to the tables below:

HOOD WELDMENTS: Model Left to Right P/N Right to Left P/N AJ-66CE/CEL 5700-031-71-71 5700-031-80-66 Hood is a combination of a 44” wash section and a 22” prewash section welded together to form one component.

TUB WELDMENTS: Model Left to Right P/N Right to Left P/N AJ-66CE/CEL 5700-041-68-83 5700-041-68-84 Tub weldment includes the 44” wash section and a 22” prewash section (with attached scrap basket weldment; actual scrap basket

and scrap basket lid are seperate items listed below).

MISCELLANEOUS ITEMS: Bolt, 1/4”-20 x 3/4” Long Hex Head 5305-274-04-00

Bolt, 1/4”-20 x 5/8” Long Hex Head 5305-274-24-00 Bolt, 1/4”-20 x 1/2” Long Hex Head 5305-274-02-00 Locknut, 1/4”-20 with Nylon Insert 5310-374-01-00 Washer, Flat, S/S, 1/4” ID 5311-174-01-00 (Note: Jackson MSC may require minimum quantities when ordering fasteners)

Scrap Basket Handle 5700-011-70-89 Scrap Basket Weldment 5700-041-92-24 Scrap Basket Lid 5700-021-71-43 Screw, 6-32 x 1/8” Long Truss Head 5305-002-23-21 (Note: Jackson MSC may require minimum quantities when ordering fasteners)

Curtain Hooks 5700-011-83-54

Page 33

WASH MANIFOLD, PREWASH MANIFOLD & STRAINER SUPPORT WELDMENTS

Prewash Manifold Weldment 5700-031-69-70

Secured to the Hood Weldment with:

Washer, Flat, S/S, 1/4” ID

5311-174-01-00

Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Wash Manifold Weldment

5700-031-71-13

AJ-66 Wash Strainer Seperator Weldment

Secured with Locknuts, 1/4”-20 with Nylon Insert

5700-031-84-38

5310-374-01-00

Page 34

UPPER WASH ARM ASSEMBLY

1Entire Assembly

5700-031-74-99

2 3

SERVICE NOTE: When replacing the 10-32 screws in the End Caps, it is recommended that a thread locking fluid be used to ensure that the screws do not back out during normal operation.

ITEM QTY DESCRIPTION MFG No.

1 3 Screw, 10-32 x 1/2" Truss Head 5305-011-39-36 2 3 Lanyard 5340-011-72-46 3 3 Locknut, 10-24 with Nylon Insert 5310-373-01-00 4 3 End Cap 5700-011-67-11 5 1 Upper Wash Arm Manifold Weldment 5700-031-67-34 6 1 Cap, Wash Tube 5700-021-69-68

Page 35

LOWER WASH ARM ASSEMBLY

1Entire Assembly

5700-031-74-66

2 3 5

SERVICE NOTE: When replacing the 10-32 screws in the End Caps, it is recommended that a thread locking fluid be used to ensure that the screws do not back out during normal operation.

ITEM QTY DESCRIPTION MFG No.

1 6 Screw, 10-32 x 1/2" Truss Head 5305-011-39-36 2 6 Lanyard 5340-011-72-46 3 6 Locknut, 10-24 with Nylon Insert 5310-373-01-00 4 6 End Cap 5700-011-67-11 5 1 Lower Wash Arm Manifold Weldment 5700-031-67-29 6 1 Manifold Quick-Release Key 5700-011-94-45

Page 36

PREWASH ARM ASSEMBLY

The enitre assembly may be ordered using part number 5700-021-74-65. SERVICE NOTE: When replacing the 10-32 screws in the End Caps, it is recommended that a thread locking fluid be used to ensure

that the screws do not back out during normal operation.

ITEM QTY DESCRIPTION MFG No.

1 1 Prewash Tube Weldment 5700-001-16-89 2 1 Screw, 10-32 x 3/8" Long Phillips Pan Head 5305-173-26-00 3 1 End Cap 5700-011-67-11 4 1 Lanyard 5340-011-72-46 5 1 Locknut, 10-24 with Nylon Insert 5310-373-01-00

Page 37

FINAL RINSE ASSEMBLY

Upper Rinse Arm Assembly

Lower Rinse Arm Assembly

ITEM QTY DESCRIPTION MFG No.

1 1 Final Rinse Manifold Weldment 5700-031-74-88 2 1 Upper Rinse Arm with Nozzles 5700-021-74-89 3 4 Upper Rinse Arm Nozzles 5700-011-78-82 4 1 Lower Rinse Arm with Nozzles 5700-021-74-90 5 4 Lower Rinse Arm Nozzles 5700-011-78-79 6 2 O-Ring (Not Shown) 5330-011-74-55 7 1 Vellumoid Gasket (Between Manifold and Hood) 5330-111-42-81

Page 38

DRIVE ASSEMBLY

13 14

ITEM QTY DESCRIPTION MFG No.

1 3 Bolt, 1/4"-20 x 3/4" Long Hex Head 5305-274-04-00 2 4 Locknut, 1/4"-20 with Nylon Insert 5310-374-01-00 3 1 Drive Rod Plate 5700-021-67-42 4 1 Adjuster Crank Assembly 5700-021-69-95 5 1 Adjuster Skotch Yoke Weldment 5700-021-69-76 6 2 Coupling & Expansion Leg Weldment 5700-021-67-50 7 1 Pawl Bar Drive Linkage Casting 9515-021-87-73 8 3 Lockwasher, 1/4", Spring 5311-274-01-00

9 1 Spacer Plate 5700-011-67-58 10 2 Bolt, 1/4"-20 x 1-1/4" Long Hex Head 5305-274-22-00 11 4 Washer, 1/4", Flat 5311-174-01-00 12 4 Locknut, 3/8"-16 with Nylon Insert 5310-376-02-00 13 2 Pillow Block 3120-021-71-87 14 2 Shaft Collar 3120-011-71-91 15 1 Drive Socket 5700-021-67-39

Page 39

DRIVE ASSEMBLY (CONTINUED)

13 10

ITEM QTY DESCRIPTION MFG No.

1 1 Drive Plate and Rod Weldment 5700-021-67-44 2 3 Lockwasher, 1/4", Spring 5311-274-01-00 3 3 Bolt, 1/4"-20 x 3/4" Long Hex Head 5305-274-04-00 4 4 Bolt, 3/8"-16 x 1-1/4" Long Hex Head 5305-276-10-00 5 8 Lockwasher, 3/8" 5311-276-01-00 6 4 Washer, 1/4", Flat 5311-174-01-00 7 4 Locknut, 1/4"-20 with Nylon Insert 5310-374-01-00 8 1 Drive Spring 5315-011-71-89

9 2 Pillow Block 3120-021-71-87 10 4 Bolt, 3/8"-16 x 3/4" Long Hex Head 5306-011-71-60 11 4 Lockwasher, 3/8" 5311-276-01-00 12 4 Locknut, 3/8"-16 with Nylon Insert 5310-376-02-00 13 2 Shaft Collar 3120-011-71-91 14 1 Drive Motor Mounting Bracket 5700-031-73-56 15 1 Adjuster Spring 5315-011-71-90

Page 40

DRIVE ASSEMBLY (CONTINUED)

4 5

Page 41

DRIVE ASSEMBLY (CONTINUED)

ITEM QTY DESCRIPTION MFG No.

1 1 Bolt, 10-32 x 3/8" Long, Hex Head 5306-011-62-45 2 1 Adjusting Handle Weldment 5700-021-72-28 3 4 Nut, 3/8"-16", Hex 5310-276-01-00 4 1 Drive Motor See Motors Page 5 1 Gear Drive 6105-121-70-54 6 8 Lockwasher, 3/8" 5311-276-01-00 7 1 Bolt, 1/2"-13 x 1-3/4" Long Hex Head 5305-011-71-94 8 2 Washer, 1/2", Flat 5311-011-71-93 9 1 Set Screw 5305-011-71-51

10 1 Roller Bearing 3120-011-71-81 11 1 Drive Hub 5700-011-67-97 12 1 Key 5700-011-71-52

Drive Motor Cover Front Weldment

5700-031-69-39

Secured with Screw, 10-32 x 3/8”

Long Phillips Trusshead

5305-173-12-00

Drive Motor Cover Rear Weldment

5700-031-69-38

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

PB Bolt Spacer (Not Shown)

5700-000-29-40

Page 42

AJ-66 (LEFT TO RIGHT) RACK RAIL ASSEMBLY

2 3

The opposite rack rail for this model (AJ-66 Left to Right) can be ordered using part number 5700-041-71-37.

ITEM QTY DESCRIPTION MFG No.

1 1 Rack Rail Weldment (AJ-66 Left to Right) 5700-031-76-27 2 8 Bolt, 1/4"-20 x 1" Long Hex Head 5305-274-27-00 3 1 Actuator Limit Switch Assembly 5700-021-75-67 4 8 Rack Guide Spacer 5700-011-71-44 5 8 Locknut, 1/4"-20 with Nylon Insert (Low Profile) 5310-374-02-00 6 3 Actuator Limit Switch Assembly 5700-021-76-96

1 Entire Assembly 5700-041-75-03

4 5

Page 43

AJ-66 (RIGHT TO LEFT) RACK RAIL ASSEMBLY

The opposite rack rail for this model (AJ-66 Right to Left) can be ordered using part number 5700-041-69-54.

ITEM QTY DESCRIPTION MFG No.

1 1 Rack Rail Weldment (AJ-66 Right to Left) 5700-031-76-28

2 8 Locknut, 1/4"-20 with Nylon Insert Low Profile 5310-374-02-00

3 3 Limit Switch Actuator Assembly 5700-021-75-67

4 8 Rack Guide Spacer 5700-011-71-44

5 1 Limit Switch Actuator Assembly 5700-021-75-68

6 8 Bolt, 1/4"-20 x 1" Long Hex Head 5305-274-27-00

Page 44

ACTUATOR ASSEMBLIES

51Limit Switch Actuator Weldment

5700-021-74-63

Part Number 5700-021-76-96

Part Number 5700-021-75-67

Part Number 5700-021-75-68

ITEM QTY DESCRIPTION MFG No.

1 1 Limit Switch Actuator Weldment (Left to Right) 5700-021-76-97 2 1 Magnet Bar 5700-111-69-25 3 1 End Cap 5700-011-60-92 4 1 Limit Switch Actuator Weldment (Right to Left) 5700-021-72-39

Page 45

WASH DOOR & VENT COWL ASSEMBLY

101Switch Box Weldment (Prewash Door)

5700-002-31-83

ITEM QTY DESCRIPTION MFG No.

1 1 Door Handle Weldment (Wash Door) 5700-011-82-63 1 1 Door Handle Weldment (Prewash Door) 5700-011-80-45 2 1 Wash Door Weldment 5700-031-83-39 2 1 Prewash Door Weldment 5700-031-95-05 3 2 Door Glide 5700-111-70-92 4 2 Vent Cowl Cover 5700-001-03-65

8 Locknut, 1/4"-20 with Nylon Insert 5310-374-01-00

5 1 See Page Entitled "Tub and Hood Weldments" N/A 6 2 Vent Cowl 5700-031-67-00 7 1 Magnetic Reed Switch (Modified) 5700-011-73-67 8 2 Locknut, 1/4"-20 with Nylon Insert 5310-274-01-00 9 2 Screw, 8-32 x 3/4" Long Binder Phillipshead 5305-011-72-66

1 Magnetic Reed Switch 5930-111-68-44

10 1 Switch Box Weldment (Wash Door) 5700-002-32-25

2 3 5 6

Top Vent Cowl Gasket: 5330-031-83-47 Side Vent Cowl Gasket: 5330-031-83-48

Page 46

MISCELLANEOUS DOOR ASSEMBLIES

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Door Guide (Left) Weldment

5700-002-32-51

Door Guide (Right) Weldment

5700-031-76-44

Door Catch Weldment

5700-031-84-40

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Door/Hood Support Weldment

Secured with Locknuts, 1/4”-20 with Nylon Insert

5700-031-84-13 5310-374-01-00

Page 47

PAWL BAR ROLLER BRACKET

ITEM QTY DESCRIPTION MFG No.

1 1 Pawl Bar Bracket (with Studs) Weldment 5700-031-84-68 1 1 Pawl Bar Bracket (without Studs) Weldment 5700-031-92-36 2 10 Locknut, 1/4"-20 with Nylon Insert 5310-374-01-00 3 2 Roller, UHMW 5700-011-68-16 4 2 Bolt, 1/4"-20 x 3/4" Long 5305-274-10-00 5 2 Roller Shaft, 3/8" x 1-1/8" Long 5700-011-68-14

Page 48

AJ-66 PAWL BAR ASSEMBLY

1 2

The entire assembly may be ordered using part number 5700-041-74-64.

ITEM QTY DESCRIPTION MFG No.

1 18 Locknut, 3/8"-16 with Nylon Insert 5310-011-72-55 2 36 Pawl Bar Spacer 5700-011-71-45 3 1 Pawl Bar Weldment 5700-031-72-78 4 18 Pawl Bar Casting 9515-021-69-00 5 18 Bolt, 3/8"-16 x 1-3/4" Long Hex Head 5306-011-36-94

3 4

Page 49

MISCELLANEOUS PARTS & WELDMENTS

Rinse Drain Weldment

5700-021-68-28

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Wash Fill Tube Weldment

Secured with Locknut, 1/4”-20 with Nylon Insert

Pawl Bar Roller Bracket Weldment without Studs

5700-031-92036

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

5700-021-71-21

Vellumoid Gasket

5330-111-42-81

5310-374-01-00

Rinse Drain Plug

5700-011-68-59

Secured with Washer, Flat, 1/4”

5311-174-01-00

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Pawl Bar Gutter Weldment

5700-021-66-86

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Page 50

MISCELLANEOUS PARTS & WELDMENTS (CONTINUED)

Top Guide Block

5700-011-69-49

Right Rinse Pan Locator Bracket

5700-021-92-37

Bottom Guide Block

5700-011-69-50

Left Rinse Pan Locator Bracket

5700-021-92-38

Upper Wash Manifold Support Bracket

5700-021-73-97

Overflow Strainer Support

5700-001-96-48

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Lower Wash Arm Support Bracket

5700-011-71-20

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Conduit Bracket 5700-021-70-88

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Page 51

MISCELLANEOUS PARTS & WELDMENTS (CONTINUED)

Door Splash Guard

5700-021-85-31

Secured with Locknut, 1/4”-20 with Nylon Insert

Hole Direction Cover Weldment

5700-002-32-50

For gasket, see page entitled “Assorted Gaskets”

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Splash Shield Weldment

5700-031-85-16 5310-374-01-00

Rinse Arm Support Bracket

5700-011-71-19

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Pipe Clamp

5700-000-35-05

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Page 52

STRAINERS

Intake Suction Scoop Strainer Weldment

5700-021-87-60

Drain Guard Strainer Weldment

5700-002-09-15

Back Strainer Weldment

5700-021-85-11

Front Strainer Weldment

5700-021-85-10

Screen Strainer with Handle Weldment

5700-002-09-04

Page 53

FLOAT SWITCH ASSEMBLY/DRESS PANEL

Float Switch Nut (1/2”-13 Thread) 5310-011-72-58

Float Switch, 60” Lead 6680-121-70-16

Order the 1/2” Flat Washer using part number 5700-011-71-93.

Dual Float Switch 6680-121-70-71

Float Support Bracket

5700-021-85-15

Float Switch Cover

5700-021-75-71

AJ-66 Front Dress Panel Left to Right: 5700-031-71-85 Right to Left: 5700-031-72-42

(Left to Right Panel, Rear View Shown)

Page 54

CURTAINS

Curtain, 21” Long x 20.5” Wide

8415-131-73-45

Middle Curtain Hook

5700-011-72-65

Secured with Locknut, 1/4”-20 with Nylon Insert

5310-374-01-00

Curtain, 12” Long x 20.5” Wide

8415-131-73-44

Curtain Hook

5700-011-83-54

Secured with Locknut, 1/4”-20 with Nylon

Insert

5310-374-01-00

Curtain Rod

5700-021-73-43

Long Curtain Decal

9905-011-73-84

Short Curtain Decal

9905-011-73-82

Page 55

RINSE TRAY ASSEMBLY

41Rinse Tray Weldment

5700-031-66-75

Order the Rinse Tray Strainer Weldment using part number 5700-041-85-09.

ITEM QTY DESCRIPTION MFG No.

1 2 Locknut, 1/4"-20 with Nylon Insert 5310-374-01-00 2 2 Washer, 1/4" 5311-174-01-00 3 2 Rinse Drain Control Plate 5700-011-68-70

Page 56

AJ-66CE/CEL

ELECTRICAL DIAGRAM

208 V - 230 V - 60 HERTZ - SINGLE PHASE

Page 57

AJ-66CE/CEL

ELECTRICAL DIAGRAM

208V - 230V - 60 HERTZ - THREE PHASE

Page 58

AJ-66CE/CEL

ELECTRICAL DIAGRAM

480V - 60 HERTZ - THREE PHASE

Jackson / Dalton Dishwasher AJ-66CE Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual