Jackson AJ-64CS, aj-86ce, AJ-100CE, AJ-100CS, AJ-86CGP User Manual
...
INSTALLATION/OPERATION &
TECHNICAL MANUAL
FOR JACKSON MODELS:
AND ASSOCIATED OPTION PACKAGES INCLUDING:
SIDE LOADER
D226 EXTERNAL STEAM BOOSTER
Jackson MSC LLC.
P.O. Box 1060
Barbourville, KY. 40906
(606) 523-9795
Fax: (606) 523-9196
www.jacksonmsc.com
AJ-64 RACK CONVEYOR DISHMACHINE SERIES
September 29, 2007
P/N 7610-002-30-93 (Revision F)
AJ-64CE
AJ-64CS
AJ-86CE
AJ-86CGP
AJ-86CS
AJ-100CE
AJ-100CGP
AJ-100CS
ALL NEW JACKSON DISHWASHERS ARE WARRANTED TO THE ORIGINAL PURCHASER TO BE FREE FROM
DEFECTS IN MATERIAL OR WORKMANSHIP, UNDER NORMAL USE AND OPERATION FOR A PERIOD OF (1) ONE
YEAR FROM THE DATE OF PURCHASE, BUT IN NO EVENT TO EXCEED (18) EIGHTEEN MONTHS FROM THE DATE
OF SHIPMENT FROM THE FACTORY.
Jackson MSC agrees under this warranty to repair or replace , at its discretion, any original part which fails under normal use due to faulty
material or workmanship during the warranty period, providing the equipment has been unaltered, and has been properly installed, maintained and operated in accordance with the applicable factory instruction manual furnished with the machine and the failure is reported to
the authorized service agency within the warranty period. This includes the use of factory specified genuine replacement parts, purchased
directly from a Jackson authorized parts distributor or service agency. Use of generic replacement parts may create a hazard and void warranty certification.
The labor to repair or replace such failed part will be paid by Jackson MSC, within the continental United States, Hawaii and Canada, during
the warranty period provided a Jackson MSC authorized service agency, or those having prior authorization from the factory, performs the
service. Any repair work by persons other than a Jackson MSC authorized service agency is the sole responsibility of the customer. Labor
coverage is limited to regular hourly rates, overtime premiums and emergency service charges will not be paid by Jackson MSC.
Accessory components not installed by the factory carry a (1) one year parts warranty only. Accessory components such as table limit switches, pressure regulators, pre rinse units, etc. that are shipped with the unit and installed at the site are included. Labor to repair or replace
these components is not covered by Jackson MSC.
This warranty is void if failure is a direct result from shipping, handling, fire, water, accident, misuse, acts of god, attempted repair by unauthorized persons, improper installation, if serial number has been removed or altered, or if unit is used for purpose other than it was originally intended.
TRAVELLIMITATIONS
Jackson MSC limits warranty travel time to (2) two hours and mileage to (100) one hundred miles. Jackson MSC will not pay for travel time
and mileage that exceeds this, or any fees such as those for air or boat travel without prior authorization.
WARRANTY REGISTRATION CARD
The warranty registration card supplied with the machine must be returned to Jackson MSC within 30 days to validate the warranty.
REPLACEMENT PARTS WARRANTY
Jackson replacement parts are warranted for a period of 90 days from the date of installation or 180 days from the date of shipment from the
factory, which ever occurs first.
PRODUCT CHANGES AND UPDATES
Jackson MSC reserves the right to make changes in design and specification of any equipment as engineering or necessity requires.
THIS IS THE ENTIRE AND ONLY WARRANTY OF JACKSON MSC. JACKSON’S LIABILITY ON ANY CLAIM OF ANY KIND, INCLUDING
NEGLIGENCE, WITH RESPECT TO THE GOODS OR SERVICES COVERED HEREUNDER, SHALL IN NO CASE EXCEED THE PRICE
OF THE GOODS OR SERVICES OR PART THEREOF WHICH GIVES RISE TO THE CLAIM.
THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING FOR FITNESS OR MERCHANTABILITY, THATARE NOT SET
FORTH HEREIN, OR THAT EXTEND BEYOND THE DURATION HEREOF. UNDER NO CIRCUMSTANCES WILL JACKSON MSC BE
LIABLE FOR ANY LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, OR FOR THE DAMAGES IN THE NATURE OF PENALTIES,
ARISING OUT OF THE USE OR INABILITY TO USE ANY OF ITS PRODUCTS.
ITEMS NOT COVERED
This warranty does not cover cleaning or deliming of the unit or any component such as, but not limited to, wash arms, rinse arms or strain-
ers at anytime. Nor does it cover adjustments such as, but not limited to timer cams, thermostats or doors, beyond 30 days from the date
of installation. In addition, the warranty will only cover the replacement of wear items such as curtains, drain balls, door guides or gaskets
during the first 30 days after installation. Also, not covered are conditions caused by the use of incorrect (non-Commercial) grade detergents,
incorrect water temperature or pressure, or hard water conditions.
MANUFACTURERS WARRANTY
ONE YEAR LIMITED PARTS & LABOR WARRANTY
i
ii
STOP!
PARE!
ARRET!
CALL 1-888-800-5672 TO REGISTER THIS PRODUCT!
FAILURE TO DO SO WILL VOID THE WARRANTY!
LLAME AL 1-888-800-5672 PARA REGISTRAR ESTE PRODUCTO!
AL NO HACERLO LA GARANTIA SERA ANULADA!
S.V.P. APPELER 1-888-800-5672 POUR ENREGISTRER CE PRODUIT,
LA GARANTIE SERA ANNULEE POUR TOUT PRODUIT NON- ENREGISTREE
iii
REVISION
REVISION
DATE
MADEBYAPPLICABLE
ECN
DETAILS
D 04-06-05 MAW
6999, 7193
7217, 7064
7212, 7259
6685, 7096
6964, 7006
Updated drawings for limit switch actuators. Changed AJ-86 drain
plumbing copper lengths. Added rack rail stabilizer kit. Replaced
heater 04540-121-76-93 with 04540-002-29-82. Updated installation instructions. Added 3 instruction sheets for limit switches.
Added instruction sheet for curtains. Added AJ-86CGP & AJ100CGP models.
E 02-02-06 MAW 7600, 7558
Added gas exhaust fan schematic, updated electric exhaust fan
schematic, updated dimensions pages. Replace Drain Weldment
05700-021-68-28 with 05700-002-51-12.
F 05-02-06 MAW
7572, 7730
7634, 7743
7428, 7571
7554, 7475
7463, 7462
7367, 7789
Pawl bar for AJ-86 R-L unit with a side loader option. Updated
scrap basket drawings. Vent cowl assembly for a hooded side
loader. Service instructions for replacing wash/rinse motors.
Added prison pawl bar packages. Thermostat replacement kits,
updated drain quench assembly, replaced wash thermostat
05930-121-67-72 with 05930-003-13-65. Heater replacment
instructions. Updated steam booster schematic. Rinse fill motor
assembly . Wash, rinse & PSI decals. Update door assembly numbers. Drain quench kit.
PG. 116 04-19-07 MAW 7898 Added 09905-003-32-20 fan load decal.
5 thru 22, 104 09-29-2007 MAW N/A
Updated dimension pages. Removed alternate table limit switches.
iv
NOMENCLATURE FOR THE MODELS COVERED IN THIS MANUAL
Model:
Serial No.:
Installation Date:
Service Rep. Name:
Phone No.:
AJ-64CS
AJ = AJ series of rack conveyors
64 = 64” wide machine
86 = 86” wide machine
100 = 100” wide machine
CE = Electrically heated, hot water sanitizing machine
CS = Steam heated, hot water sanitizing machine
CGP = Gas heated, hot water sanitizing machine
Jackson MSC LLC. provides technical support for all
of the dishmachines detailed in this manual. We
strongly recommend that you refer to this manual
before making a call to our technical support staff.
Please have this manual with you when you call so
that our staff can refer you, if necessary, to the proper page. Technical support is available from 8:00
a.m. to 5:00 p.m. (EST), Monday through Friday.
Technical support is not available on holidays.
Contact technical support toll free at 1-888-800-
5672. Please remember that technical support is
available for service personnel only.
SECTION
DESCRIPTION PAGE
I. SPECIFICATION INFORMATION
Operating Characteristics 2
Electrical Requirements 3
D226 Steam Booster Parameters 4
AJ-64 Electric - Left to Right 5
AJ-64 Electric - Right to Left 6
AJ-64 Gas - Left to Right 7
AJ-64 Gas - Right to Left 8
AJ-64 Steam - Left to Right 9
AJ-64 Steam - Right to Left 10
AJ-86 Electric - Left to Right 11
AJ-86 Electric - Right to Left 12
AJ-86 Gas - Left to Right 13
AJ-86 Gas - Right to Left 14
AJ-86 Steam - Left to Right 15
AJ-86 Steam - Right to Left 16
AJ-100 Electric - Left to Right 17
AJ-100 Electric - Right to Left 18
AJ-100 Gas - Left to Right 19
AJ-100 Gas - Right to Left 20
AJ-100 Steam - Left to Right 21
AJ-100 Steam - Right to Left 22
Side Loader (Left to Right) Dimensions 23
Side Loader (Right to Left) Dimensions 24
Side Loader (Installed) Dimensions 25
D226 Steam Booster Dimensions 26
D226 Steam Booster Plumbing Line Drawings 27
Typical Electric and Gas Booster Dimensions 28
II. INSTALLATION & OPERATION INSTRUCTIONS
Installation Instructions 30
Deliming Operations 33
Curtain Installation Diagram 34
Side Loader Installation & Operation Instructions 35
D226 Steam Booster Installation & Operation Instructions 36
Gas Conveyor Hose Installation 38
Dishmachine Operating Instructions 40
Detergent Control 42
Striker Plate Limit Switch Installation Instructions 43
III. PREVENTATIVE MAINTENANCE
General Maintenance 45
D226 Maintenance 46
Lubrication Chart for Drive Gear 47
Drive Motor Gear Reducer Preventative Maintenance 48
IV. TROUBLESHOOTING SECTION
Common Problems 50
D226 Common Problems 52
TABLE OF CONTENTS
v
VI. PARTS SECTION
AJ-64 Control Box Assembly 54
AJ-86/AJ-100 Control Box Assembly 56
Motor Overload Chart 58
Heater Box Assembly 59
Heater Assembly 60
Frame Weldments/Front Dress Panels 62
Prewash Plumbing Assembly 63
Incoming Plumbing Assembly 64
Rinse Header Plumbing Assembly (CGP Models) 66
External Electric Booster Option Incoming Plumbing 67
External Electric Booster Option Outlet Plumbing 68
WPRK Plumbing Option 69
3/4” Solenoid Valve & 3/4” NPT Vacuum Breaker Repair Parts Kits 70
Steam Unit Wash Tank Coil Assembly 71
Steam Inlet Plumbing (Left to Right) 72
Steam Inlet Plumbing (Right to Left) 74
Steam Outlet Plumbing (Left to Right) 76
Steam Outlet Plumbing (Right to Left) 77
Gas Coil Assembly (CGP Models) 78
Rinse Booster Tank Assembly (CGP Models) 79
Recirculating Pump Assembly (CGP Models) 80
Hose Connections (CGP Models) 81
AJ-64 Series Drain Plumbing Assemblies 82
AJ-86 & AJ-100 Drain Plumbing Assemblies (Left to Right) 83
AJ-86 & AJ-100 Drain Plumbing Assemblies (Right to Left) 84
Drain Quench Assembly 85
Prewash & Wash Motor Assemblies 86
Prewash & Wash Pump Weldments 87
Prewash & Upper Wash Arm Assemblies 88
Lower Wash Arm Assembly 89
Upper & Lower Power Rinse Arm Assemblies 90
Final Rinse Assembly 91
Drive Assembly 92
Door Assemblies 94
Pawl Bar Roller Bracket 95
AJ-64 & AJ-86 Pawl Bar Assemblies 96
AJ-64 Rack Rail Assembly 97
Miscellaneous Parts & Weldments 98
Manifolds/Strainer Support Weldments 99
Strainers 100
Float Switch Components/Scrap Basket Assembly 101
Curtains/Tub Magnets 102
Vent Cowl Assembly/Vent Scoop Option 103
Exhaust Fan Control Option/Table Limit Switch Options 104
SIDE LOADER SECTION
Side Loader Track Assembly/Leg Replacements 105
Side LoaderPawl Bar Assemblies 106
Side Loader Vent Cowl Option 107
D226 STEAM BOOSTER SECTION
Control Box Assembly 108
Plumbing Assembly 109
Go*Box Components 111
Rinse Fill Motor Option 112
TABLE OF CONTENTS
PARTS
vi
VII. ELECTRICAL SCHEMATICS
AJ-64CE
208-230 Volt, 60 Hz, 1 Phase Primary Side 114
208-230 Volt, 60 Hz, 1 Phase Secondary Side 115
208-230 Volt, 60 Hz, 3 Phase Primary Side 116
208-230 Volt, 60 Hz, 3 Phase Secondary Side 117
460-575-600 Volt, 60 Hz, 3 Phase Primary Side 118
460-575-600 Volt, 60 Hz, 3 Phase Secondary Side 119
AJ-64CS
208-230 Volt, 60 Hz, 1 Phase Primary Side 120
208-230 Volt, 60 Hz, 1 Phase Secondary Side 121
208-230 Volt, 60 Hz, 3 Phase Primary Side 122
208-230 Volt, 60 Hz, 3 Phase Secondary Side 123
460-575-600 Volt, 60 Hz, 3 Phase Primary Side 124
460-575-600 Volt, 60 Hz, 3 Phase Secondary Side 125
AJ-86CE & AJ-100CE
208-230 Volt, 60 Hz, 1 Phase Primary Side 126
208-230 Volt, 60 Hz, 1 Phase Secondary Side 127
208-230 Volt, 60 Hz, 3 Phase Primary Side 128
208-230 Volt, 60 Hz, 3 Phase Secondary Side 129
460-575-600 Volt, 60 Hz, 3 Phase Primary Side 130
460-575-600 Volt, 60 Hz, 3 Phase Secondary Side 131
AJ-86CS & AJ-100CS
208-230 Volt, 60 Hz, 1 Phase Primary Side 132
208-230 Volt, 60 Hz, 1 Phase Secondary Side 133
208-230 Volt, 60 Hz, 3 Phase Primary Side 134
208-230 Volt, 60 Hz, 3 Phase Secondary Side 135
460-575-600 Volt, 60 Hz, 3 Phase Primary Side 136
460-575-600 Volt, 60 Hz, 3 Phase Secondary Side 137
AJ-86CGP & AJ100CGP
208-230 Volt, 60 Hz, 1 Phase Primary Side 138
208-230 Volt, 60 Hz, 1 Phase Secondary Side 139
208-230 Volt, 60 Hz, 3 Phase Primary Side 140
208-230 Volt, 60 Hz, 3 Phase Secondary Side 141
460-575-600 Volt, 60 Hz, 3 Phase Primary Side 142
460-575-600 Volt, 60 Hz, 3 Phase Secondary Side 143
Exhaust Fan Hook-Up Schematic 144
D226 Steam Booster/Drain Quench/Conveyor Side Loader Schematics 145
VIII. MAINTENANCE & REPAIR CENTERS 146
TABLE OF CONTENTS
ELECTRICAL SCHEMATICS
vii
1
SECTION 1:
SPECIFICATION INFORMATION
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: N/A
SECTION 1: SPECIFICATION INFORMATION
OPERATING CHARACTERISTICS
2
RACKS PER HOUR:
AJ-64-86-100CE/CS/CGP 287
DISHES OR GLASSES PER HOUR:
AJ-64-86-100CE/CS/CGP 7200
PREWASH TANK CAPACITY (GALLONS):
AJ-86CE/CS/CGP 16
AJ-100CE/CS/CGP 16
WASH TANK CAPACITY (GALLONS):
AJ-64-86-100CE/CS/CGP 15.4
POWER RINSE TANK CAPACITY (GALLONS):
AJ-86CE/CS/CGP 15.4
AJ-100CE/CS/CGP 15.4
PREWASH PUMP CAPACITY (GPM):
AJ-86CE/CS/CGP 120
AJ-100CE/CS/CGP 270
WASH PUMP CAPACITY
GALLONS PER MINUTE (ALL MODELS): 270
POWER RINSE PUMP CAPACITY
GALLONS PER MINUTE (ALL MODELS): 270
VENTING REQUIREMENTS (CFM)(100% CAP.):
INPUT END 200
OUTPUT END 400
TOTAL 600
CONVEYOR SPEED (FPM):
AJ-64-86-100CE/CS/CGP MACHINES 8.0
GALLONS PER RACK:
AJ-64-86-100CE/CS/CGP MACHINES .77
WATER TEMPERATURES:
AJ-64-86-100CE/CS/CGP MODELS:
WASH (MINIMUM) 150°F
POWER RINSE (MINIMUM) 160°F
FINAL RINSE (MINIMUM) 180°F
FLOW PRESSURE (PSI) 20±5
FLOWRATE (GPM):
AJ-64-86-100CE/CS/CGP 3.7
STEAM COIL TANK HEAT (CS MODELS ONLY):
STEAM INLET PRESSURE (PSIG) 10-20
STEAM CONNECTION NPT 3/4”
CONSUMPTION @ 15 PSIG (lbs/hr):
AJ-64-86-100CS/CSL 100
MOTOR ELECTRICAL CHARACTERISTICS:
DRIVE MOTOR HP 1/4
WASH MOTOR HP 2
POWER RINSE MOTOR HP 2
PREWASH MOTOR HP:
AJ-86 MODELS 1
AJ-100 MODELS 2
NOTE: Typical Electrical Circuit is based upon (1) 125% of
the full amperage load of the machine and (2) typical
fixed-trip circuit breaker sizes as listed in the NEC 2002
Edition. Local codes may require more stringent protection than what is displayed here. Always verify with your
electrical service contractor that your circuit protection is
adequate and meets all applicable national and local
codes. These numbers are provided in this manual simply for reference and may change without notice at any
given time.
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: N/A
SECTION 1: SPECIFICATION INFORMATION
ELECTRICAL REQUIREMENTS
3
AJ-64CE MODELS
TYPICAL
TOTAL ELECTRICAL
VOL
TS PH HZ AMPS CIRCUIT
208 1 60 139 A 175 AMP
230 1 60 128 A 175 AMP
208 3 60 82 A 110 AMP
230 3 60 76 A 100 AMP
460 3 60 38 A 50 AMP
AJ-64CS MODELS
TYPICAL
TOTAL ELECTRICAL
VOL
TS PH HZ AMPS CIRCUIT
208 1 60 19 A 25 AMP
230 1 60 19 A 25 AMP
208 3 60 13 A 20 AMP
230 3 60 13 A 20 AMP
460 3 60 7 A 15 AMP
AJ-86CE MODELS
TYPICAL
TOTAL ELECTRICAL
VOL
TS PH HZ AMPS CIRCUIT
208 1 60 145 A 200 AMP
230 1 60 134 A 175 AMP
208 3 60 86 A 110 AMP
230 3 60 79 A 100 AMP
460 3 60 39 A 50 AMP
AJ-86CGP MODELS
TYPICAL
TOTAL ELECTRICAL
VOL
TS PH HZ AMPS CIRCUIT
208 1 60 26 A 35 AMP
230 1 60 26 A 35 AMP
208 3 60 17 A 25 AMP
230 3 60 17 A 25 AMP
460 3 60 9 A 15 AMP
AJ-86CS MODELS
TYPICAL
TOTAL ELECTRICAL
VOLTS PH HZ AMPS CIRCUIT
208 1 60 25 A 35 AMP
230 1 60 25 A 35 AMP
208 3 60 16 A 20 AMP
230 3 60 16 A 20 AMP
460 3 60 8 A 15 AMP
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: N/A
SECTION 1: SPECIFICATION INFORMATION
ELECTRICAL REQUIREMENTS (CONTINUED)/D226 STEAM BOOSTER PARAMETERS
4
AJ-100CE MODELS
TYPICAL
TOTAL ELECTRICAL
VOL
TS PH HZ AMPS CIRCUIT
208 1 60 148 A 200 AMP
230 1 60 136 A 175 AMP
208 3 60 88 A 110 AMP
230 3 60 81 A 110 AMP
460 3 60 41 A 60 AMP
AJ-100CGP
MODELS
TYPICAL
TOTAL ELECTRICAL
VOL
TS PH HZ AMPS CIRCUIT
208 1 60 28 A 35 AMP
230 1 60 28 A 35 AMP
208 3 60 19 A 25 AMP
230 3 60 19 A 25 AMP
460 3 60 10 A 15 AMP
AJ-100CS MODELS
TYPICAL
TOTAL ELECTRICAL
VOL
TS PH HZ AMPS CIRCUIT
208 1 60 28 A 35 AMP
230 1 60 28 A 35 AMP
208 3 60 18 A 25 AMP
230 3 60 18 A 25 AMP
460 3 60 9 A 15 AMP
NOTE: Always refer to the machine data plate for specific
electrical and water requirements. The material provided
on this page is for reference only and may be subject to
change without notice.
D226 STEAM BOOSTER
ELECTRICAL REQUIREMENTS:
VOLTAGE (V) 208-230
FREQUENCY (HZ) 60
PHASE SINGLE
WATER REQUIREMENTS:
INCOMING WATER TEMPERATURE (MINIMUM) 110°F
FLOW PRESSURE (PSI) 20±5
STEAM REQUIREMENTS:
INCOMING STEAM PRESSURE (PSIG) 15-25
HEAT EXCHANGER SPECIFICATIONS:*
TUBESIDE WORKING PRESSURE (PSI) 125
SHELLSIDE WORKING PRESSURE (PSI) 125
TUBESIDE HYDROSTATIC TEST PRESSURE (PSI) 250
SHELLSIDE HYDROSTATIC TEST PRESSURE (PSI)
188
MAXIMUM OPERATING TEMPERATURE 295°F
MAXIMUM SHELLSIDE STEAM PRESSURE (PSI) 125
* - Indicates typical design criteria but is subject to change
without notice. For more information, contact you authorized
Jackson service representative.
WATER OUTLET SAFETY VALVE
SET PRESSURE (PSI): 125
STEAM RELIEF VALVE SET PRESSURE (PSI): 50
Right Side
34 [864mm]
21 [533mm]
25 [635mm]
12 [307mm]
25 [635mm]
Table to Table
Overall
Dish Clearance
B
Left to Right
Drive
Unit
Left Side
66
1
2
[1692mm]
1
2
[15mm]
84 [2134mm]
With Doors Open
Rear of
Machine
Legend to Drawing
A - Machine water inlet 3/4" NPT,
180°F Hi-temp,
140°F Low-temp minimum
B - Electrical connection
C - Drain connection 1-1/2" NPT
D - Vent collar - Optional
E - Vent cowl standard
Note: All vertical dimensions are
+/- 1/2" from floor due to adjustable
bullet feet.
1 [25mm]
4" (102 mm) wide x 16" (406 mm)
long cutout in Vent Cowl/Splash
Shield. Shipped with Cover Plate.
Floor Sink Or Drain
With 3" [76 mm]
Minimum Drain Line
25 [637mm]
64 [1626mm]
72 [1829mm]
80 [2032mm]
8 [204mm]
14 [355mm]
Scrap
Trough
Minimum
21 [535mm]
65
1
2
[1665mm]
A
Drive
Unit
Front View
75
1
2
[1915mm]
62
1
2
[1588mm]
29 [737mm]
6
1
2
[165mm]
10 [254mm]
7 [178mm]
D
E
C
4 [102mm]
8 [203mm]
14 [354mm]
Minimum
10" High
Table
Backsplash
Scrap
Trough
32
3
4
[833mm]
35 [891mm]
5 [127mm]
8
1
2
[218mm]
C
B
24
1
2
[622mm]
3/4" [19 mm]
Table Turndown
Flange 3/4" Max
21" [533 mm]
Rack Rail Height
Above Dishtable
1/4" [6mm] - 5/16" [8mm]
Rack Rail
Tub
Table
Use Silicone Sealer
Between Table and
Lip of Machine to
Prevent Leakage
Recommended Table Fabrication
Note: Tub Will Accept
a Table Flange
Up to 24 7/8"
[632 mm]
60
1
4
[1530mm]
SECTION 1: SPECIFICATION INFORMATION
AJ-64 ELECTRIC - LEFT TO RIGHT
5
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: 09-29-2007
Right Side
34 [864mm]
21 [533mm]
25 [635mm]
12 [307mm]
25 [635mm]
Table to Table
Overall
Dish Clearance
B
Right to Left
Drive
Unit
Left Side
66
1
2
[1692mm]
1
2
[15mm]
84 [2134mm]
With Doors Open
Rear of
Machine
Legend to Drawing
A - Machine water inlet 3/4" NPT,
180°F Hi-temp,
140°F Low-temp minimum
B - Electrical connection
C - Drain connection 1-1/2" NPT
D - Vent collar - Optional
E - Vent cowl standard
Note: All vertical dimensions are
+/- 1/2" from floor due to adjustable
bullet feet.
1 [25mm]
4" (102 mm) wide x 16" (406 mm)
long cutout in Vent Cowl/Splash
Shield. Shipped with Cover Plate.
Floor Sink Or Drain
With 3" (76 mm)
Minimum Drain Line
25 [637mm]
64 [1626mm]
72 [1829mm]
80 [2032mm]
8 [204mm]
21 [535mm]
65
1
2
[1665mm]
A
Drive
Unit
Front View
75
1
2
[1915mm]
62
1
2
[1588mm]
29 [737mm]
6
1
2
[165mm]
10 [254mm]
7 [178mm]
D
E
C
4 [102mm]
8 [203mm]
60
1
4
[1528mm]
32
3
4
[833mm]
35 [891mm]
5 [127mm]
8
1
2
[218mm]
C
B
24
1
2
[622mm]
3/4" (19 mm)
Table Turndown
Flange 3/4" Max
21" (533 mm)
Rack Rail Height
Above Dishtable
1/4" (6mm) - 5/16" (8mm)
Rack Rail
Tub
Table
Use Silicone Sealer
Between Table and
Lip of Machine to
Prevent Leakage
Recommended Table Fabrication
Note: Tub Will Accept
a Table Flange
Up to 24 7/8"
(632 mm)
SECTION 1: SPECIFICATION INFORMATION
AJ-64 ELECTRIC - RIGHT TO LEFT
6
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: 09-29-2007
Right Side
34 [864mm]
21 [533mm]
25 [635mm]
12 [307mm]
25 [635mm]
Table to Table
Overall
Dish Clearance
20
3
4
[527mm]
8
3
4
[222mm]
11
3
4
[298mm]
14
3
4
[375mm]
6 [154mm]
30 [763mm]
14 [357mm]
7
1
4
[185mm]
1
1
4
[35mm]
6 [152mm]
31
1
4
[795mm]
6
1
2
[165mm]
26
1
2
[673mm]
B
Left to Right
Drive
Unit
Left Side
66
1
2
[1692mm]
1
2
[15mm]
84 [2134mm]
With Doors Open
Rear of
Machine
Legend to Drawing
A - Machine water inlet 3/4" NPT, 180°F
Hi-temp,140°F Low-temp minimum
B - Electrical connection
C - Drain connection 1-1/2" NPT
D - Vent collar - Optional
E - Vent cowl standard
F - 3/4" NPT 180°F Water Inlet for wash tank
fill, final rinse, & tank heating. From gas
booster heater. Interconnecting hose
provided by manufacturer.
G - 3/4" NPT 140°F Water inlet for
gas booster heater.
H - 3/4" NPT 180°F Water Outlet
connection to line on dishmachine.
Connection hose provided by
manufacturer.
J - 3/4" NPT Gas Connection
K - 4" OD Vent pipe connection. Flue to
be installed to meet local codes by
installing contractor.
Note: All vertical dimensions are +/- 1/2" from
floor due to adjustable bullet feet.
1 [25mm]
K
J
H
G
3/4" (19 mm)
Table Turndown
Flange 3/4" Max
21" (533 mm)
Rack Rail Height
Above Dishtable
1/4" (6mm) - 5/16" (8mm)
Rack Rail
Tub
Table
Use Silicone Sealer
Between Table and
Lip of Machine to
Prevent Leakage
Recommended Table Fabrication
Note: Tub Will Accept
a Table Flange
Up to 24 7/8"
(632 mm)
F
4" (102 mm) wide x 16" (406 mm)
long cutout in Vent Cowl/Splash
Shield. Shipped with Cover Plate.
Floor Sink Or Drain
With 3" (76 mm)
Minimum Drain Line
25 [637mm]
64 [1626mm]
72 [1826mm]
80 [2032mm]
8 [204mm]
14 [355mm]
Scrap
Trough
Minimum
21 [535mm]
36 [914mm]
K
J
H
G
65
1
2
[1665mm]
A
Drive
Unit
Front View
75
1
2
[1915mm]
62
1
2
[1588mm]
29 [737mm]
6
1
2
[165mm]
10 [254mm]
7 [178mm]
D
E
C
4 [102mm]
8 [203mm]
14 [354mm]
Minimum
10" High
Table
Backsplash
Scrap
Trough
60
1
4
[1530mm]
32
3
4
[833mm]
35 [891mm]
5 [127mm]
8
1
2
[218mm]
C
24
1
2
[622mm]
SECTION 1: SPECIFICATION INFORMATION
AJ-64 GAS - LEFT TO RIGHT
7
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: 09-29-2007
Right Side
34 [864mm]
21 [533mm]
25 [635mm]
12 [307mm]
25 [635mm]
Table to Table
Overall
Dish Clearance
B
Drive
Unit
Left Side
66
1
2
[1692mm]
1
2
[15mm]
84 [2134mm]
With Doors Open
Rear of
Machine
1 [25mm]
4" (102 mm) wide x 16" (406 mm)
long cutout in Vent Cowl/Splash
Shield. Shipped with C over Plate.
64 [1626mm]
72 [1829mm]
80 [2032mm]
65
1
2
[1665mm]
A
Drive
Unit
Front View
75
1
2
[1915mm]
62
1
2
[1588mm]
29 [737mm]
6
1
2
[165mm]
10 [254mm]
7 [178mm]
D
E
C
4 [102mm]
8 [203mm]
32
3
4
[833mm]
35 [891mm]
5 [127mm]
8
1
2
[218mm]
C
B
24
1
2
[622mm]
3/4" (19 mm)
Table Turndown
Flange 3/4" Ma x
21" (533 mm)
Rack Rail Height
Above Dishtable
1/4" (6mm) - 5/16" (8mm)
Rack Rail
Tub
Table
Use Silicone Sealer
Between Table a nd
Lip of Machine to
Prevent Leakage
Recommended Table Fabrication
Note: Tub Will Accept
a Table Flange
Up to 24 7/8"
(632 mm)
Floor Sink Or Drain
With 3" (76 mm)
Minimum Drain Line
25 [637mm]
8 [204mm]
21 [535mm]
60
1
4
[1530mm]
Right to Left
Legend to Drawing
A - Machine water inlet 3/4" NPT, 180°F
Hi-temp,140°F Low-t emp minimum
B - Electrical connection
C - Drain connection 1-1/2" NPT
D - Vent collar - Optional
E - Vent cowl standa rd
F - 3/4" NPT 180°F Water Inlet for wash tank
fill, final rinse, & tank heating. From gas
booster heater. Interconnecting hose
provided by manufacturer.
G - 3/4" NPT 140°F Water inlet for
gas booster heater.
H - 3/4" NPT 180°F Water Outlet
connection to line on dishmachine.
Connection hose provided by
manufacturer.
J - 3/4" NPT Gas Connection
K - 4" OD Vent pipe connection. Flue to
be installed to meet local codes by
installing contractor.
Note: All ver t i cal dimensions are +/- 1/2" fro m
floor due to adjustable bullet feet.
20
3
4
[527mm]
8
3
4
[222mm]
11
3
4
[298mm]
14
3
4
[375mm]
6 [152mm]
30 [763mm]
14 [357mm]
7
1
4
[185mm]
1
1
4
[35mm]
K
J
H
G
16 [407mm]
26
1
2
[672mm]
6
1
2
[163mm]
36 [914mm]
31
1
4
[794mm]
K
J
H
G
A
SECTION 1: SPECIFICATION INFORMATION
AJ-64 GAS - RIGHT TO LEFT
8
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: 09-29-2007
Right Side
34 [864mm]
21 [533mm]
25 [635mm]
12 [307mm]
25 [635mm]
Table to Table
Overall
Dish Clearance
B
Drive
Unit
Left Side
66
1
2
[1692mm]
1
2
[15mm]
84 [2134mm]
With Doors Open
Rear of
Machine
1 [25mm]
3/4" (19 mm)
Table Turndown
Flange 3/4" Max
21" (533 mm)
Rack Rail Height
Above Dishtable
1/4" (6mm) - 5/16" (8mm)
Rack Rail
Tub
Table
Use Silicone Sealer
Between Table and
Lip of Machine to
Prevent Leakage
Recommended Table Fabrication
Note: Tub Will Accept
a Table Flange
Up to 24 7/8"
(632 mm)
4" (102 mm) wide x 16" (406 mm)
long cutout in Vent Cowl/Splash
Shield. Shipped with Cover Plate.
Floor Sink Or Drain
With 3" (76 mm)
Minimum Drain Line
25 [637mm]
64 [1626mm]
72 [1829mm]
80 [2032mm]
8 [204mm]
14 [355mm]
Scrap
Trough
Minimum
21 [535mm]
65
1
2
[1665mm]
A
Drive
Unit
Front View
75
1
2
[1915mm]
62
1
2
[1588mm]
29 [737mm]
6
1
2
[165mm]
10 [254mm]
7 [178mm]
D
E
C
4 [102mm]
8 [203mm]
14 [354mm]
Minimum
10" High
Table
Backsplash
Scrap
Trough
60
1
4
[1528mm]
32
3
4
[833mm]
35 [891mm]
5 [127mm]
8
1
2
[218mm]
C
Left to Right
Legend
A - Machine water inlet 3/4" NPT 180°F
Hi-temp,140°F Low-temp minimum
B - Electrical connection
C - Drain connection 1-1/2" NPT
D - Vent collar - Optional
E - Vent cowl standard
F - 3/4" NPT Steam connection
G - 3/4" NPT Condensate return
H - Steam electrical connection
J - 1" NPT Steam connection
K - 3/4" Condensate connection
L - 3/4" NPT Incoming 110°F water
connection
M - 3/4" NPT 180°F water to dishmachine.
Note: All vertical dimensions are +/- 1/2"
from floor due to adjustable bullet feet.
12
1
2
[316mm]
F
17
1
2
[442mm]
6
1
2
[162mm]
11
1
2
[295mm]
15
3
4
[400mm]
16
1
2
[417mm]
43 [1092mm]
11
1
4
[285mm]
13
1
2
[345mm]
23
3
4
[604mm]
38 [966mm]
6
1
4
[159mm]
5
3
4
[148mm]
4
1
4
[110mm]
8
1
2
[218mm]
H
J
L
M
K
L
H
J
M
F
B
10 [255mm]
G
10
1
2
[264mm]
24
1
2
[622mm]
SECTION 1: SPECIFICATION INFORMATION
AJ-64 STEAM - LEFT TO RIGHT
9
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: 09-29-2007
Right Side
34 [864mm]
21 [533mm]
25 [635mm]
12 [307mm]
25 [635mm]
Table to Table
Overall
Dish Clearance
B
Right to Left
Drive
Unit
Left Side
66
1
2
[1692mm]
1
2
[15mm]
84 [2134mm]
With Doors Open
Rear of
Machine
1 [25mm]
4" (102 mm) wide x 16" (406 mm)
long cutout in Vent Cowl/Splash
Shield. Shipped with Cover Plate.
64 [1626mm]
72 [1829mm]
80 [2032mm]
65
1
2
[1665mm]
A
Drive
Unit
Front View
75
1
2
[1915mm]
62
1
2
[1588mm]
29 [737mm]
6
1
2
[165mm]
10 [254mm]
7 [178mm]
D
E
C
4 [102mm]
8 [203mm]
32
3
4
[833mm]
35 [891mm]
5 [127mm]
8
1
2
[218mm]
C
B
24
1
2
[622mm]
Legend
A - Machine water inlet 3/4" NPT 180°F
Hi-temp,140°F Low-temp minimum
B - Electrical connecti on
C - Drain connection 1-1/2" NPT
D - Vent collar - Optional
E - Vent cowl standard
F - 3/4" NPT Steam connection
G - 3/4" NPT Condensate return
H - Steam electrical connection
J - 1" NPT Steam connection
K - 3/4" Condensate connection
L - 3/4" NPT Incoming 110°F water
connection
M - 3/4" NPT 180°F water to dishmachine.
Note: All vertical dimensions are
+/- 1/2" from floor due to
adjustable bullet feet.
3/4" (19 mm)
Table Turndown
Flange 3/4" Max
21" (533 mm)
Rack Rail Height
Above Dishtable
1/4" (6mm) - 5/16" (8mm)
Rack Rail
Tub
Table
Use Silicone Sealer
Between Table and
Lip of Machine to
Prevent Leakage
Recommended Table Fabrication
Note: Tub Will Accept
a Table Flange
Up to 24 7/8"
(632 mm)
Floor Sink Or Drain
With 3" (76 mm)
Minimum Drain Line
25 [637mm]
8 [204mm]
21 [535mm]
11
1
4
[285mm]
13
1
2
[345mm]
23
3
4
[604mm]
38 [966mm]
6
1
4
[159mm]
5
3
4
[148mm]
4
1
4
[110mm]
8
1
2
[218mm]
H
J
L
M
K
F
60
1
4
[1530mm]
12
1
2
[316mm]
F
17
1
2
[445mm]
6
1
2
[162mm]
11
1
2
[295mm]
15
3
4
[400mm]
16
1
2
[417mm]
43 [1092mm]
L
H
J
M
SECTION 1: SPECIFICATION INFORMATION
AJ-64 STEAM - RIGHT TO LEFT
10
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: 09-29-2007
Loading...