Přenosný video monitor
Portable Video Monitor
CZ
MZZ56200
OBSAH
CZ
VLASTNOSTI VIDEO MONITORU ............................................................................... 3
INSTALACE SYSTÉMU .............................................................................................6
NASTAVENÍ VIDEO MONITORU .................................................................................11
ŘEŠENÍ VZNIKLÝCH ZÁVAD ....................................................................................13
EN
FEATURES OF VIDEO MONITOR .............................................................................. 16
INSTALLATION OF THE SYSTEM .............................................................................. 19
VIDEO MONITOR SETTING .................................................................................... 24
TROUBLESHOOTING ........................................................................................... 26
1716
ENEN
MZZ56200MZZ56200
Wireless Receiver
Receiver Cradle (charging base)
Wireless Camera
RCA Cable
Power Adaptor for Camera
Power Adaptor for Receiver
Rechargeable Accumulator
RECEIVER
a) Front of the Receiver
1. Receiver Antenna – Should not be close to the
metallic parts.
2. Power and Audio Level LEDs – The green LED
indicates the receiver power is ON. The red
LEDs indicate the received audio levels (low to
high).
3. LCD Screen – Displays video from the camera.
4. MENU Button – Press to access the receiver
menu. Press the button again to exit the menu.
5. Navigation Controls and OK Button – Setting
of parameters in viewing mode and moving in
the menu.
Viewing Mode (= live video): The arrow controls are
used while watching live video from the camera:
Press the UP/DOWN arrows to increase or
decrease the volume.
Menu: Use the UP/DOWN/LEFT/RIGHT
arrows to move in Menu. Press the OK button to
conrm the selected option in the menu.
6. SCAN Button – When the SCAN button is pressed, the LCD screen is turned off but the camera
continuously watches the given space. If any sound is detected by the camera above the preset
audio level, the receiver will beep and display the picture from the monitored area for 5 seconds. The
receiver will return to scan mode about 5 seconds after activation by sound. To exit scan mode press
any button except the OK button on the front panel of the receiver. The scan feature can be used for
the following two reasons:
a) during the night to prevent the user from being disturbed by the bright LCD screen (i.e. when sleeping),
b) to prolong the viewing period when battery powered (one charging).
7. Speaker – for sound reproduction.
8. Belt Clip and Wall Mount – Use the belt clip to enable the carrying of the receiver with you or you can
use the wall mount hole to hang the receiver on a wall (screw not included).
9. Stand – when you take the plastic stand away from the receiver, you can place it on a flat surface.
When battery charging is needed, use the receiver cradle.
PORTABLE DIGITAL WIRELESS VIDEOMONITOR SYSTEM
Thank you very much for the purchase of CMD 6129S Tiny product. We wish you pleasant pictures
whenever the Tiny is on.
FEATURES OF THE TINY VIDEO MONITOR
Digital wireless technology provides excellent image quality and clarity
An interference-free, secure and private signal
Up to 450 ft (150 m) wireless transmission range (maximum open-space transmission range).
The actual range is dependent upon building construction and other objects, materials and other
obstructions in the path of the wireless signal.
Listening-in with exceptional sound clarity
Safety warning feature noties you when out of range
Camera (baby unit):
High resolution camera
Automatic night vision for low light viewing up to 15 feet / 4.5 meters (Under ideal conditions. Objects at
or beyond this range may be partially or completely obscured, depending on the camera application.)
Built-in microphone
Camera can be mains powered or powered from accumulator (recharged when the adaptor is plugged in)
Receiver (parents’ unit):
2.4” color LCD monitor with superior image quality
Video and audio output for viewing on TV or recording
Rechargeable lithium polymer battery for true portability
Convenient receiver cradle and belt clip included
Audio level indicator
GETTING STARTED
The system comes with the following components:
Please check your package contents to conrm that you
have received the complete system, including all the components
shown below. If anything is missing, please contact your distributor.
1918
ENEN
MZZ56200MZZ56200
b) Bottom of the Receiver
10. Pair Button – This button is not used for Tiny monitor.
c) Side of the Receiver
11. Night Light Button – Press to turn the night light ON or OFF remotely on the active camera.
12. Alarm +/- Button – To set the volume level of the transmitted sound and of the receiver beeping.
13. Power Button – Press to turn the receiver ON or OFF.
14. Audio and Video Output – The receiver can be connected with a TV, monitor or a recording device via
the included audio / video cable to view video from a camera. The same output is on the receiver cradle.
NOTE: When the audio / video cable is connected the LCD screen turns off. The LCD screen will turn
back on when the audio / video cable is disconnected.
15. Power Input (9V DC) – For connecting of power adaptor (included in the kit).
d) Receiver Cradle Inputs
16. Audio and Video Output – Connect the included audio / video cable to view video from the receiver
on a TV, monitor or to record it (when docked).
NOTE: The Audio and Video Output function will not work if the cradle is not connected to the mains.
When the audio / video cable is connected, the LCD screen is switched off. It is switched on again
when the audio / video cable is disconnected.
17. Power Input (DC 9V) – Connect the included power adaptor (DC 9V) to the receiver cradle to power
the receiver or to charge the receiver accumulaor (when docked).
RECEIVER INSTALLATION
You can use the wireless receiver in the receiver cradle or you can connect the mains cable directly to
the receiver:
1. Carefully unpack the receiver and the receiver cradle.
2. Place the receiver cradle or receiver in a place that will have clear reception from your camera.
3. Plug the AC adaptor power cable into the input socket on the cradle or on the receiver and connect
it to the mains.
4. The receiver should be charged for 6 hours prior to rst usage so the built-in rechargeable battery
is fully charged. Do not remove the adaptor cable from the receiver or the cradle during the initial
charging process. After this, the receiver should be charged as required.
5. If you would like to view the video on a larger screen, connect the included AV cable to the cradle or
receiver, and connect the other end of the cable to the Video IN (yellow) and Audio IN (white) ports
on the TV or other device.
NOTE: The video resolution is set for VGA (640x480 pixels), so the picture might be grainy when
displayed on the larger screen. This is not a product defect. For best TV performance use the PIP
(Picture in Picture) TV function. This function allows you to view a TV program as well as the video from
the camera placed in a small window in the corner.
2120
ENEN
MZZ56200MZZ56200
CAMERA
a) Front & Back of the Camera
1. Camera Antenna – Should not be close to the metallic parts.
2. Night Light Switch – The button itself is used as a night light (press to switch the night light ON or
OFF). Alternatively you can use the button 11 on the receiver to switch the camera light ON or OFF
remotely.
3. Lens/IR LED Cover – Infrared LEDs enable better vision during low or no light.
4. Microphone – Hears all the sounds in the monitored room and transmits them to the wireless receiver.
5. Power (9V DC) – To connect the 9V DC power adaptor to the camera.
NOTE: The camera can also be powered by a rechargeable accumulator (included) or 4 AA batteries.
The batteries would only be used if there is no mains power. When powered from an AC adaptor,
inserted accumulator would be recharged.
6. Pair Button – This button is not used for Tiny monitor..
b) Side of the Camera
7. Volume Setting – To adjust the sound alarm sensitivity. The receiver will beep to alert the user when
the sound is above the preset sound level. Adjust the side wheel to increase or decrease the level.
8. Camera ON/OFF Switch – To switch the camera ON or OFF.
CAMERA INSTALLATION
Before you install the camera, carefully plan where and how it should be positioned, and where you will
route the cable of the power adaptor. It is also needed to check the image quality on the receiver before
the camera is installed permanently. The best is to place the wireless receiver on the most common
place where it will be used.
Installation Warnings
Place the camera to optimize the viewing area – select a location that provides a clear view of the area
you want to monitor, which is free from dust and is not in line-of-sight of a strong light source or direct
sunlight. Avoid installing the camera where there are thick walls or any obstructions between the camera
and the receiver.
Night Vision
The camera has built-in infrared LEDs, which provides the camera with the
ability to view a monitored space in poor light conditions. It is important
to use the provided power adaptor (and not the batteries) with the night
vision feature to prolong the viewing period in poor light conditions, as the
built-in IR LEDs will drain the battery more quickly than in regular daytime
use.
2322
ENEN
MZZ56200MZZ56200
INSTALLING THE CAMERA
1. Carefully unpack the camera and remove the foil on IR LED cover.
2. Mount the camera on a wall
Mark the position of the screw holes on the wall, drill the holes and
screw 2 screws into them, then rmly attach the camera to the
wall by placing the stand over the installed screws and pushing the
base downwards.
NOTE: The camera can also be simply placed on a flat surface
without any special installation needed.
3. Adjust the camera to monitor the requested area.
CONNECTING THE CAMERA TO THE POWER
The camera can be powered either by the provided power adaptor or using the included rechargeable
accumulator (or 4 AA batteries, not included).
NOTE: If you plan to permanently mount the camera on a wall location, it is recommended to use the
included camera power adaptor to prevent interruptions to the image, as using battery power is only
intended as a temporary power solution.
Power Adaptor
Connect the power adaptor to the camera. Make sure the power adaptor is plugged into an outlet.
Rechargeable Accumulator
1. Remove the battery cover from the
base of the camera.
2. Insert the included rechargeable
accumulator into the battery
compartment. Make sure to
correctly line up the positive (+)
and negative (-) terminals of the
accumulator.
3. Put the battery cover back on.
NOTE: If the camera is connected to
the AC adaptor, the batteries will not
be used, although the accumulator
would be recharged. The accumulator
is intended for short term usage
only.
Connect the 9V adaptor to the Power
Input on the back side of the camera
VIEWING MODE
1. Signal Indicator –shows the strength of the signal being received from the camera. The number of
bars in the signal indicator shows the strength of the signal.
Signal Strength Indicator Warning
Perfect None
Good Nove
Fair Low Signal
Low Low Signal
No Signal No Signal
2. Channel Indicator – Displays the current channel
number. Press the RIGHT arrow on the receiver
to switch between available cameras.
Note: This option is not available for the Tiny monitor.
LOW SIGNAL AND NO SIGNAL WARNINGS
When the receiver is positioned too far from the camera, the following warning messages are displayed:
LOW SIGNAL: The "LOW SIGNAL" appears
when the receiver has one or two bars. You will
still get an image, however updating may be
less frequent.
NO SIGNAL: The "NO SIGNAL" message
means the receiver cannot access the camera.
Please reposition the camera, or check the
camera power.
Position the base holes over the
screws. Slide the base down to lock
the base in place.
2524
ENEN
MZZ56200MZZ56200
ACCESSING MENU OPTIONS OF THE RECEIVER
Press the MENU button on the receiver to enter the menu options. Use the navigating arrows to move
up/down/left/right in the menu, and press the OK button to conrm a selection.
Main Menu
The Main Menu contains 4 submenus:
1. PAIRING – For adding more cameras to the receiver.
NOTE: This option is not available for the Tiny monitor.
2. EV – Adjusts the exposure level of the camera.
3. POWER SAVING – Turns on the receiver
power save mode (when no activity on the camera is
detected, the LCD screen on receiver will switch off).
4. SETTING – Sets the AV output options and
resets the receiver to factory defaults (erases all
congurations).
Pairing Submenu
Function not available for Tiny monitor. The system
comes with a single camera that has already been
paired. When you switch on the receiver and the
camera, you are able to see the video immediately.
ADjUSTING THE RECEIVER VOLUME
The receiver volume can be adjusted by using the
UP/DOWN arrows while watching the video.
Press the DOWN arrow to decrease the volume
and the UP arrow to increase the volume. When
the volume is set to one bar (lowest setting), the
volume is muted.
The volume strength indicator is shown on
display while the volume is being adjusted and will
disappear 10 seconds after nal setting.
EV Menu
The EV Menu is used to adjust the exposure of the camera.
Use the LEFT and RIGHT arrows to change the bar from darkest (left) to lightest (right). Press the
OK button to accept the setting.
Power Saving Submenu
The Power Saving Menu is used to turn off the LCD
screen at a preset time to save the battery. This
function can be set from 1 minute to up to 10 minutes.
The Cancel option switches this feature off.
When the Power Saving option is on, the LCD screen
would only be switched on by activation by the preset
volume level or by pushing any button on the front
of the receiver.
When the LCD screen is activated by button
pushing, it will turn back to Power Saving mode
after the preset time expires. If it is activated by
sound in the monitored area, it will go back to
a black screen after 5 seconds.
Setting Submenu
The Setting Menu contains 2 submenus:
1. A/V Out – Changes the quality of the image sent
to the A/V receiving device (i.e. TV or monitor).
2. Default – Resets all menu settings to the factory
defaults.
A/V Out Menu
The A/V Out menu option is used to adjust the
resolution quality of the image for TV, monitor etc.
Use the UP and DOWN arrows to select a
resolution, and press OK to accept your option.
NOTE: It is strongly recommended to use the “High”
resolution to ensure the best image resolution
on a large screen (default setting).
Default Menu
The Default option is used to reset the receiver to
factory settings – all menu settings will be reset.
Use the UP and DOWN arrows to select YES,
and press OK to accept.
NOTE: Camera pairing will NOT be affected by a
rese t.
2726
ENEN
MZZ56200MZZ56200
Receiver Frequency Range 2.400 GHz~2.482 GHz
Data Rate 1.5 Mbps
Receiving Sensitivity -81 dBm
Demodulation Type GFSK with FHSS
Resolution H: 480 V: 240
Viewing Angle H: 50° V: 50°
A/V Output / Resolution VGA 640x320 / 15FPS, QVGA 320x240 / 30 fps
Alert volume 80 dB ±10 % / 1 m
Power Requirement 9 V DC ±5%
Power Consumption 400mA max without charging, 800mA with charging
Battery operation up to 3 hours (according the condition)
Battery parameters LiPO 7.4 V / 950 mAh (MLP 563450)
Operating Temp Range 14°F ~ 140°F / -10°C ~ +60°C
Max. Operating Humidity 85% RH
TROUBLESHOOTING
If any difculties with the video monitor occur, please see the possible solutions below:
Symptoms Solution
No picture from a camera
1. Check the AC adaptor of the camera – whether it is connected
to the camera and plugged into the mains.
2. Make sure that the camera and receiver are both ON.
3. Make sure that the camera is in range of the receiver.
4. If using the accumulator, check the capacity or replace the batteries
if needed.
The picture is dropping out
1. The signal from the camera may be too low. Move the camera closer
to the receiver.
2. Try repositioning the camera, receiver or both to improve the reception.
Audio problems
1. Ensure that the volume on the receiver is turned up.
2. Make sure that there is no disturbing sound within range of the
camera microphone.
3. If the unit emits a loud screeching noise (feedback), move the camera or receiver farther apart.
The picture has become
choppy
The picture may become choppy when experiencing a lower
frame rate (refreshing less than 10 times a second).
Try moving the camera closer to the receiver. Remove
obstructions between the receiver and camera.
The picture appears to be
grainy when using the AV
output for viewing on a
large screen
The picture might be grainy as the camera video resolution is set to
VGA (640x480 pixels). This is not a product defect.
1. For best performance use the PIP (Picture in Picture)
function on the TV.
2. Check if the video resolution is set to the “high” option.
TECHNICAL SPECIFICATION – RECEIVER
Transmit Frequency Range 2.400 GHz~2.482 GHz
Can be operated according to ERC REC 70-03
Data Rate 1.5 Mbps
Transmitting Power 14 dBm (TYP)
Modulation Type GFSK with FHSS
Communication Range 150 m (Line of Sight)
Image Sensor Type 1/4” Color CMOS Image Sensor
Effective Pixels H: 640 V: 480
Image Processing Motion jPEG
Image Resolution / Frame Rate H: 640 V: 480 / 30FPS Max.
White Balance Yes
Audio parameters AEG 0 dB ~ 24 dB
Lens 4.9 mm / F2.8
Viewing Angle (Diagonal) 60°
Minimum Illumination 2.5 LUX (IR off), 0 LUX (IR on)
IR LED / Night Vision Range 8 LEDs / 840nm 5m (with IR LED)
Power Requirement 9V DC ±5%
Power Consumption
360mA MAX (w/ Night Light) / 300mA (without Night Light)
Battery operation up to 3 hours (according the condition)
Battery parameters NiMH 6 V / 750 mAh (BP 610)
Operating Temperature 14°F ~ 104°F (-10°C ~ +40°C)
Max. Operating Humidity 85 %
Environmental Rating 14°F ~ 140°F (-10°C ~ +60°C)
Dimensions / (W x D x H) 2.6” x 5.7” x 3.3” / 66mm x 145mm x 84mm
TECHNICAL SPECIFICATION – CAMERA
JABLOTRON ALARMS a.s. hereby declares that the CMD 6129S Tiny
is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC and complies with part 15 of the
FCC rules. Operation is subject to the following two conditions: 1. This
device may not cause harmful interference, and 2. This device must
accept any interference received, including interference that may cause
undesired operation.
Caution: Changes or modications not expressly approved by Jablotron
could void the user´s authority to operate the equipment. The original of the
conformity assessment can be found on the web site www.jablotron.com.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.
SERVICE PROVIDED BY:
JABLOTRON ALARMS a.s.
Pod Skalkou 4567/33
466 01 Jablonec nad Nisou
Czech Republic
tel: +420 483 559 956
e-mail: nanny@jablotron.cz
web: www.jablotron.com
1177
FCC ID Sj8CA610
Nanny watches
over your treasure
Jednoduché
ovládání
Certifikované
zdravotnické
zařízení
Včasné
varování
Easy
operation
Medical
device
Early
warning
certification
OUR RECOMMENDATION
Loading...