Jablotron JA85P User Manual

The JA-85P mini-size wireless motion detector

+

lithium

DIP switches

PCB

release

s

e

c

4 m

2.60m

1,

Internet: www.jablotron.com

Pod Skalkou 33

The JA-85P is a component of Jablotron’s Oasis 80 alarm system. The mini­size motion detector uses a PIR sensor and it is designed for indoor use in
buildings or in cars. The battery-powered detector communicates via OASIS
radio protocol.

u

r

e

d

(

C

L

I

C

K

)

battery

AA 3V

and the ignition key is turned off then detector triggering is indicated by a short
flash of the LED.

Battery replacement

The detector battery is regularly checked. If the battery has expired, then the
user or installer is informed. The detector continues to work and each
movement in front of the detector is shown by a brief LED flash. The battery
should be replaced within two weeks by a qualified technician.

After battery replacement the detector needs two minutes to stabilise during
which the LED is permanently lit. After battery replacement test the
functioning of the detector. An expired battery should not be thrown into the
garbage, but disposed of according to local regulations.

- see table

Detection characteristics

The detector can react to movements within a distance of up to 5 meters,
see the following diagram.

r = 3m

Installation

open here

AA 3V

Installation shall only be undertaken by technicians holding a certificate
issued by an authorized distributor. The detector can be installed on a wall or
on a ceiling. In a car it can be installed high on the interior vertical surface

r = 5m

between the front and rear doors. Within the detection range of the PIR
sensor avoid the presence of objects rapidly changing in temperature, such as
electrical heaters, gas appliances etc. Moving objects with a temperature close
to that of humans such as curtains moving above a radiator, and pets should
also be avoided. Detectors should not be near fast-moving air e.g. near
ventilation fans or open windows or doors. There should also be no obstacles
blocking the detector’s “view” of the protected area. Keep the detector away
from metal objects which could interfere with radio communication.

Warning:

The most frequent cause of false alarms is bad detector-

positioning.

Do not set (arm) this detector if there are any people or pets moving within
the protected area.

1.

Release the detector installation bracket

2.

Attach the bracket

to a desired place and reinstall the detector onto the

(by turning it clockwise).

bracket.

3. Open the detector

4. Remove the internal PIR module

5.

Set the detector DIP switches

6.

Return the PIR module in

7.

Leave the battery disconnected and the detector open

cover by pressing the tab.

held by an internal tab.

(see the “DIP switches” section below).

to the plastic cover.

and then follow
the receiver (or control panel or car alarm) manual. The detector enrolls by
connecting up its battery while the receiver is in enrollment mode.

8.

After detector enrollment, close its cover,

and then

test its functionality.

wait until its indicator turns off

To enroll a detector after having already connected a battery, first disconnect
the battery, wait 30 seconds and reconnect it.

DIP switches

# OFF ON

Increased immunity

1

slower reaction (car use)

2* Delayed
3**

Radio

supervision off

natural reaction

4*** 5 minute sleep

*

This DIP switch has an effect if the detector is used with a CA car alarm or

with a

Radio

time

Normal immunity

alarms (indoor use)

Instant

natural reaction

supervision on

1 minute sleep

time

to false

with an Oasis control panel which has a natural reaction assigned to the
JA-85P’s address. It also has no effect when used with a UC-8x or AC-8x
receiver.

** Radio communication supervision should be switched off if a detector

installed in a car is enrolled to an Oasis control panel in a house (to avoid
lost detector indication when the car drives away).

*** To save battery energy, the detector switches to battery-save mode 15

minutes after the cover is closed. During battery-save mode the PIR sensor
still always watches out for movement. The first movement detected is then
transmitted instantly, and for the next 5 minutes or 1 minute the PIR sensor
ignores any further movement. After this period, the PIR sensor then returns
to watching out for movement until re-triggered.

Testing the detector

15 minutes after closing the detector cover, the LED shows detector
triggering. The strength and quality of detector signals can be measured by an
Oasis control panel in Service mode. If the detector is enrolled to a car alarm

The JA-80P mini-size wireless motion detector 1 / 1 MHP52700_PTS_FCC

Car alarm co-operation

Several types of Jablotron’s car alarms allow for wireless detector
enrollment. A JA-85P detector, if enrolled, should be placed in the upper part
of car’s interior – e.g. fixed to the plastic part of the ceiling light, to side posts or
to the ceiling upholstery (this does not require the bottom handle to be used).
Always take the detection characteristic into consideration when positioning
the detector. Keep in mind that the spots behind mechanical obstacles (seats,
props) are invisible to the detector. Multiple detectors can be used
simultaneously – a detector has no effect to other detectors function.

The detector should
with a JA-85P enrolled

not be exposed to direct sunlight

all windows must be closed

to prevent false alarm

. When arming a car

caused by strong hot air blasts or by passing-by persons. However, this rule

can be omitted when partial arming is used and the detector belongs to the
INT group.

DIP switches No. 1 and 3 must be OFF

.

Technical specifications

Voltage Lithium battery type CR14505 (AA 3.0V)
Calculated battery lifetime approx. 3 years (sleep time 5 min.)
Communication band:
Communication range: approx. 100m (open area)
PIR sensor detection angle/detection range: 360° / 5 m
Operational environment according to EN 50131-1 II. internal space
Operational temperature range -10 to +55 °C
Dimensions 88 x 46 x 27mm
EN 50131-1, CLC/TS 50131-2-2, EN 50131-5-3 classification: grade 2
Complies with ETSI EN 300220, EN 50130-4, EN 55022, EN 60950­ANSI C63.4
Can be operated according to ERC REC 70-03, FCC Part 15

FCC ID VL6JA85P

Jablotron Ltd. hereby declares that the JA-85P is in compliance
with the essential requirements and other relevant provisions of
Directive 1999/5/EC and complies with part 15 of the FCC rules.
Operation is subject the the following two conditions: 1. This
device may not cause harmful interference, and 2. this device
must accept any interference received, including interference
that may cause undesired operation.. The original of the
conformity assessment can be found on the web site

www.jablotron.com, Technical Support section.

Changes or modifications no expressly approved by Jablotron could void
the user´s authority to operate the equipment

Note

local regulations. Although this product does not contain any
harmful materials we suggest you return the product to the dealer
or directly to the manufacturer after use.

868 MHz, Oasis protocol

: Dispose of batteries safely depending on battery type and

466 01 Jablonec nad Nisou
Czech Republic

Tel.: [phone]
fax: [phone]

CAUTION: