JA-63 „Profi“
User manual
Alarm system JA-63 „Profi“ - 2 - MGK51504
Contents:
1 Limited warranty ........................................................................................................................... 2
2 Indicators....................................................................................................................................... 3
3 Controlling the system ................................................................................................................. 4
3.1 Arming ................................................................................................................................... 5
3.2 Disarming .............................................................................................................................. 6
3.3 Panic Alarm ........................................................................................................................... 6
3.4 To stop ALARM ..................................................................................................................... 6
3.5 Home arming ......................................................................................................................... 7
3.6 Door opening ......................................................................................................................... 7
3.7 Alarm memory reading .......................................................................................................... 7
3.8 Split system arming ............................................................................................................... 7
3.9 Subsystem arming ................................................................................................................. 8
3.10 Appliance control ................................................................................................................... 8
4 User’s settings .............................................................................................................................. 8
4.1 New master code .................................................................................................................. 8
4.2 User codes setting ................................................................................................................. 9
4.3 Internal clock setting .............................................................................................................. 9
4.4 Automatic arming / disarming .............................................................................................. 10
4.5 Bypass ................................................................................................................................. 10
5 Digital communicator ................................................................................................................. 11
5.1 JA-60GSM Dialer module .................................................................................................... 11
5.2 JA-65X Telephone communicator ....................................................................................... 11
5.2.1 Telephone numbers for voice message sending ........................................................ 11
5.2.2 Telephone communicator testing ............................................................................... 12
6 System testing ............................................................................................................................ 12
7 Battery replacement ................................................................................................................... 12
8 Enrollment of the control panel to UC-2xx modules ............................................................... 13
1 Limited warranty
Subject to the conditions of this Limited warranty Jablotron Ltd. warrants this product to
be free from defects in design, material and workmanship at the time of its original
purchase by a customer for a subsequent period of two (2) years. Should your Product
need warranty service, please return it to the dealer from whom it was purchased.
Conditions:
1. The warranty is valid only if the original receipt issue d to the original p urchaser by
the dealer, specifying the date of purchase, is presented with the Product to be
repaired or replaced. Jablotron reserves the right to refuse warranty service if this
information has been removed or changed.
2. This warranty does not cover any failure of the Product due to misuse, including
but not limited to use in other than the normal and customary manner, in
accordance with instructions for use and maintenance of the Product. Nor does
this warranty cover any failure of the product due to accident, modification,
adjustment, improper repair or acts of God.
3. This warranty does not apply to batteries nor modules of other suppliers (e.g. SIM
card of the GSM provider).
4. The warranty provided does not affect the consumer's statutory rights under
applicable national legislation in force, nor the consumer's rights against the
dealer arising from their sales / purchase contract.
Alarm system JA-63 „Profi“ - 3 - MGK51504
Note: features of this system can be substantially modified by programming
during installation. The installer should instruct the users how to operate and test
the system.
2 Indicators
The alarm system’s status is indicated on the keypad. There can be multiple
keypads in the system and in such a case all keypads will have identical functions.
A keypad’s LED indicators and display inform the user about the conditions of the
system.
LED indicators:
Alarm: alarm triggered by an intruder, smoke, gas etc
Tamper: opened cover, damaged detector, excessive
number of attempts to enter code, etc.
Fault: power loss, lost communication with a detector
etc., (view details by pressing N)
Battery: battery of the device specified on the display is
low. See battery replacement section.
information received from a wireless item or wireless
communication of the keypad in progress
Armed: continues = armed, slow blinking = exit delay,
fast blinking = entrance delay
Power: continues = AC power & back up battery O.K.,
blinking = failure (AC or back up battery), off = control
panel is not powered
88 display specifies event source:
wireless
detector 12
indicated event (Alarm, Tamper, Failure or
Battery) was caused by detector number 12
wired zone 2
indicated event (Alarm, Tamper, Failure or
Battery) was caused by wired zone number 2
wireless
controller 3
indicated event was caused by wireless
controller (remote control, keypad, Panic button)
number 3
Control panel
indicated event (Tamper or Failure) was caused
by the control panel
Wireless siren
indicated event (Tamper, Failure or Battery)
was caused by the outdoor wireless siren
Sub control
panel
indicated event (Alarm, Tamper, Failure or
Battery) was caused by the sub control panel
Alarm system JA-63 „Profi“ - 4 - MGK51504
Telephone line
indicated event (Tamper or Failure) was caused
by the telephone line
digital bus
indicated event (Tamper or Failure) was caused
by a device (keypad or PC) connected to the
digital bus
communication
failure
wireless keypad lost connection with the cont rol
panel
error self testing error – call installer
tab. 1
88 display specifies mode of the control panel:
user mode
authorized supervisor can test, bypass zones, change
batteries, record voice messages, program tel.
numbers and adjust internal clock in this mode
home arming
system is partially armed – particular detectors are
bypassed (someone remains in the house)
A section armed
A section is armed (split system)
B section armed
B section is armed (split system)
complete
arming
system is completely armed
bypass
warning that some detectors are bypassed –
indicated while arming
key pressed
waiting for more data to complete the entry
programming
mode
for installer programming and testing
tab. 2
3 Controlling the system
The system can by controlled by keypads, remote controls or by a PC with the
Comlink Software.
User codes
Can be used to arm and disarm the sy st em or to reset an ala rm. The re can b e up t o
14 different user codes for individual users. The system stores to its memory which
code was used for which operation as well as the time &date of usage. This data can
go to a Central monitoring station and can also be viewed using a PC with Comlink
software. All user codes are empty as a factory default and should be programm ed by
the supervisor (see section 4.2).
Alarm system JA-63 „Profi“ - 5 - MGK51504
Master code
Is an extra (15th) access code for the supervisor. It can operate the system and it
also allows for the programming of the other user codes and to enter the user mode
(see section 4).
Factory default master code is 1234. The supervisor should change it after
installation.
Service code
Is an extra code, used by the installer to enter the programming mode. End users
are not usually told this code.
If an invalid access code is entered more than four times in a given period of
time, it will trigger a Tamper alarm on the control panel.
3.1 Arming
On the keypad - enter your user code or press the fast arming button*.
On the remote control (RC-4x) – press the
button
system will beep once and the exit delay countdown will start
ARMED indicator will flash during exit delay
**
you should leave the protected area within the duration of the
exit delay
If there are 4 beeps while arming, the system is indicating an unusual situation
and the keypad will display the specific information:
ALARM and a zone number – the zone is not ready (opened door etc.),
check the indicated item.
b – some detectors are bypassed (done by supervisor, see part 4.5)
Note: supervisor can program an automatic arming for a desired time (for
example, the house will be armed automatically at 21:00 if left disarmed).
Automatic disarming is also programmable. See part 4.4 for details.
*
Fast arming (without access code) can be disabled by the installer
**
The JA-60F battery powered wireless keypad will stop indications 10sec after the most recent key
entry.
Alarm system JA-63 „Profi“ - 6 - MGK51504
3.2 Disarming
On the keypad - enter your user code
On the remote control (RC-4x) – press the button
system will beep twice
if there are 3 beeps, important information is indicated and will
be displayed on the keypad. Examples:
o FAILURE LED is flashing – press the N key to view the cause
o ALARM LED and zone number is flashing = alarm in the memory.
Be careful and check the house.
if you enter the premises when the system is armed, the entrance delay
countdown will start after you trigger a delayed detector (ARM LED will
flash and beeps will sound if programmed so
*
).
3.3 Panic Alarm
If you are in danger you can trigger the silent panic alarm to inconspicuously call
for help. While in Panic alarm mode the control panel can send a voice message,
an SMS message and data to a central monitoring station via a telephone line
(depends on installation settings).
Panic alarm can be triggered:
On the keypad - press the panic key and then enter your
access code.
On the remote control (RC-4x) - press the
and buttons
simultaneously. The remote control can be switched (by installer) to a
Panic mode, in which pressing of any button will trigger the Panic alarm.
By pressing this large sized panic button, the RC-22 (can be installed
on the wall, under a desk etc.).
3.4 To stop ALARM
If an alarm is triggered when you are present, you can stop it by entering your access
code or by pressing button
on the remote control.
Sending of voice and SMS messages will cease after the alarm is stopped. All
corresponding report codes (alarm triggering & stopping) will be sent to the
central monitoring station.
If user does not stop the alarm, it will stop automatically after the programmed
period and the alarm memory indicator will activate. The control panel will
return to the same mode as before the alarm.
Alarm system JA-63 „Profi“ - 7 - MGK51504
3.5 Home arming
The installer can program particular detectors so that they will be automatically
bypassed in the so called “Home” partial arming. This allows for people to stay in
the particular part of the house after arming. To arm partially:
On the keypad press home arming button
H will indicate the Home partial arming on the keypad.
To disarm a partially armed system - enter your user code or press the or
button on the remote control.
3.6 Door opening
An electrical door lock (if installed) can be controlled via the alarm system.
Press the door opening button on the keypad to release the
lock.
3.7 Alarm memory reading
All events (arming, disarming, alarms, failures…) are recorded into the control
panel’s memory along with the time and date. The complete system history can be
viewed using a PC with Comlink software. Alarms and failures can also be viewed
on the keypad by entering:
F 4 - will show the last recorded alarm or failure. Press key 4 multiple
times to go deeper in to the memory.
3.8 Split system arming
The system can be split by the installer into two independent sections (A,B) and
a shared section (corridors, stairs, a main door…). This allows for a particular user
to arm and disarm only a particular section of the house with his/her code or
remote control (exactly as in a non split system). Arming of sections A and B is
indicated by I I symbols on the keypad. The shared section will be armed
automatically when A and B sections are both armed.
With the master code the supervisor can arm and disarm both sections. If the
master code is entered, the system will arm (if completely disarmed) or disarm (if
any section is armed).
Entering F1 master code will control only section A and F2 master code only
section B (this is true only when fast arming is disabled by the installer).
Note: partial Home arming is not possible if the system is split.
Alarm system JA-63 „Profi“ - 8 - MGK51504
3.9 Subsystem arming
In a large building a sub control panel can be enrolled to the JA-63. The
subsystem reports all alarms and failures to the main system.
The installer can program if the systems will be armed and disarmed separately
(by their own codes and remote controls) or if the main control panel will rule the
sub control panel. Ask your installer for explanation on how to operate your
system if a sub control is panel installed.
3.10 Appliance control
The system can be used to control an electrical appliance (light, heating,
ventilation etc.). In such a case users can operate the device:
Locally with keypad* – entering F81 (ON) or F80 (OFF).
Remotely by phone keypad or by SMS messages – the control panel
must be equipped with GSM communicator for this feature
*
Installer can program that this feature will work only when the entry is followed by a user code.
4 User’s settings
Following section is designated for the system supervisor, who knows the
master code.
All programming sequences can be terminated before completed (by N key).
4.1 New master code
The master code is used by the supervisor. The factory default master code is
1234 and you should program your own four digits code. Code programming is only
possible when the system is disarmed.
To change an existing master code enter:
F 5 xxxx yyyy yyyy
where xxxx is the existing and yyyy is the new master code (new code must be
entered twice to avoid an error).
Example:
Existing code 1234 will change to 6723 entering: F 5 1234 6723 6723
Alarm system JA-63 „Profi“ - 9 - MGK51504
4.2 User codes setting
There can be up to 14 differen t user codes for ind ividual users. The syste m stores
to its memory which code was used for wh at event and when. Th is data can go to a
Central monitoring station as well and can also be viewed by a PC with Comlink
software.
All user codes are empty as a factory default and the supervisor should program
them entering:
F 6 xxxx yy zzzz
where xxxx is the master code, yy is the user code index (from 01 to 14) and
zzzz is the new user code.
Example:
If the master code is 1234 and the user 3 new code should be 5277 enter:
F 6 1234 03 5277
To delete a particular user code, enter 0000 as the new code (combination
0000 can not be used as a valid code).
Example:
If the master code is 1234 the user 3 code can be deleted by:
F 6 1234 03 0000
Notes:
You can program new codes only when the system is disarmed.
The supervisor should record the codes to the table on last page of this
manual (it should be kept hidden in a safe place).
If the system is split, the supervisor can change the user codes, but can
not change to which section the particular code belongs (only the installer
can change this).
4.3 Internal clock setting
The control panel has a built in real time clock. All events are stored to the event
memory including the time & date. The clock should be set after installation, but
the supervisor can set the clock while in the user mode.
To switch the control panel to the user mode enter F 0 master code. User
mode will be indicated by a U on the keypad. To set the clock enter:
4 hh mm DD MM YY
where: hh = hours; mm = minutes; DD = day; MM = month and YY = year
Example: at 21:30 on March 19. 2005 enter: 4 21 30 19 03 04
To exit user mode press N.
Alarm system JA-63 „Profi“ - 10 - MGK51504
Actions' table
a no splitting split
0 no action no action
1 arm all arm all
2 disarm disarm all
3 partial arming arm A
4 partial arming arm B
5 disarm disarm A
6 disarm disarm B
4.4 Automatic arming / disarming
The system can automatically arm and disarm for a requested period of a day.
While in the user more, up to ten instructions (time & action) can be programmed
in the period of one day.
To switch the control panel to the user mode enter F 0 master code. User
mode will be indicated by a U on the keypad. To program automatic arming enter:
64 n a hh mm
where: n = instruction number from 0 to 9
a = action (see the actions' table)
hh = hours (from 00 to 23)
mm = minutes (from 00 to 59)
Example: to program an automatic complete
arming of the system at 21:15 everyday
enter: 64 0 1 21 15
Notes:
If any automatic action is selected, it will be preformed everyday at the
programmed time, following the internal control panel clock.
The automatic arming and disarming can be overridden manually anytime
(by a user code or a remote control)
If the control panel is in the requested arming mode before the action
time, the programmed action will not change the arming
Factory default setting - all instructions are set for no action
To exit user mode, press the N key.
4.5 Bypass
The supervisor can bypass (switch off) particular zones (potential sources of
alarms) while in the user mode. If a zone is bypassed, it can’t trigger an alarm.
To switch the control panel to the user mode enter F 0 master code. User
mode will be indicated by a U on the keypad.
To set up bypass:
1. Press key 1 to open the bypass menu.
2. With key 1 and 7 you can scroll all potential alarm sources (wireless
detectors are distinguished with the symbol
).
3. Select the source (detector, wired input…) which you want to bypass and:
a. either press key 2 for 2 seconds to bypass the source for the next
arming period (confirmed by flashing Battery LED);
b. or press key 3 for 2 seconds to bypass the source permanently
(confirmed by the Battery LED being permanently lit);
Alarm system JA-63 „Profi“ - 11 - MGK51504
c. multiple pressing and holding of the keys (2 or 3) will switch the
bypass on – off – on – off …
4. By repeating step 3. you can bypass all required alarm sources.
To close the Bypass menu press the N key. If anything is bypassed when
arming, four beeps will sound and b will be displayed on the keypad during the
exit delay (and partial arming will be recorded to the memory).
All bypasses selected with key 2 (next arming period bypasses) will switch off
automatically with the first following disarming.
The existing bypass setting can be checked or modified in the bypass menu.
All bypasses can be deleted by key 4 in the b ypass menu. They can also be
deleted by the programming mode opening or if the control panel is
disconnected from the power completely (AC & back up battery).
To exit user mode press N.
5 Digital communicator
5.1 JA-60GSM Dialer module
If the control panel is equipped with a JA-60GSM communicator, please look at
the JA-60GSM user manual for details about user’s setting.
5.2 JA-65X Telephone communicator
If the control panel is equipped with a JA-65X telephone communicator and if
the installer enabled the supervisor to modify the communications settings, only
then will the following programming be possible.
5.2.1 Telephone numbers for voice message sending
Up to 4 telephone numbers can be programmed in the user mode. To switch the
control panel to the user mode enter F 0 master code. User mode will be
indicated by a U on the keypad.
Store telephone numbers for voice message by entering:
7 xx... xx F y
where xx...xx = telephone number
y = memory number from 1 to 4
A telephone number can have a maximum of 16 digits. A dialing pause can be
entered with F0
Note: enter a pause (F0) after the last digit of a number, which is calling a
mobile phone. This way the number will be called only once and the dialer will
not check the line signals (some mobile phone systems do not generate standard
telephone line signals).
Alarm system JA-63 „Profi“ - 12 - MGK51504
Example: to store tel. number 0 123456 to memory no. 2 enter: 7 0 F0 12345 F2
To delete a telephone number enter:
7 F0 Fy
where y is a memory number from 1 to 4
To exit user mode, press the N key.
5.2.2 Telephone communicator testing
Testing is possible in the user mode. To switch the control panel to the user
mode enter F 0 master code. User mode will be indicated by a U on the keypad.
Entering 89 will cause the communicator to send voice message number 2 to all
programmed telephone numbers. It will also send an SMS message if
programmed. The telephone line signals will be audible from the control panel’s
built in speaker during the test (if the dialer is triggered by an alarm in normal
operation, it will call silently). Testing can be terminated with the N key.
Notify the people who will be called before testing!
To exit user mode, press the N key.
6 System testing
The supervisor should test the system monthly. For testing the control panel
should be in the user mode. Enter F0 master code to switch to th e user mode (U
will be indicated on the keypad).
No alarm can be triggered while in the user mode and any triggering of a
detector, a remote control or a panic button will be indicated on the keypad.
Note: some detectors (for example the wireless motion detector) in normal mode can not
send the next triggering information until 5 minutes after t he previ ous tri ggering w as sent. It
is possible to switch such a detector to the testing mode by opening and closin g its cover.
See the particular product manual for more details.
If anything does not work during testing, call the installer.
To exit user mode press N.
7 Battery replacement
All the battery-powered items perform regular battery testing. If the lifetime of the
battery is near the end, the system will indicate the need for battery replacement
(Battery indicator and the item address will be shown on the keypad).
When any detector or keypad asks for new batteries, they should be replaced in
a week. To replace batteries either call the installer or do the following:
switch the control panel to the user mode (entering F0 master code)
Alarm system JA-63 „Profi“ - 13 - MGK51504
open the cover of the detector (keypad)
replace its batteries with new ones (use only corresponding size and good
quality alkaline batteries). Wait for approximately 20 seconds before
inserting batteries
close the device’s cover and test its function.
to exit User mode, press the N key on the keypad
Note: normal battery life in wireless items is about 1 year. Exposure to a very cold
temperature, frequent triggering or low initial battery capacity can shorten the
battery life.
Recommendations: the system should be annually inspected by a professional
installer. The control panel and the outdoor siren back up batteries should be
replaced with new ones after 5 years.
8 Enrollment of the control panel to UC-2xx modules
The wireless control panel can send data to UC–216, UC–222 and UC-260 output
modules. To enroll the JA-63 control panel to the UC-2xx:
switch the control panel to the user mode (entering F0 master code)
switch the UC-2xx to learning mode (see its manual)
enter 299 on the ala rm system keypa d – the control panel will enroll
press the N key on the keypad to exit User mode,
Alarm system JA-63 „Profi“ - 14 - MGK51504
User codes and controllers
code
index
user name
section
notes
A B
0.
Master code - supervisor
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
c1
c2
c3
c4
c5
c6
c7
c8
Telephone communicator setting
memory calling to tel. number notes
1.
2.
3.
4.
5. Pager
Timers
exit delay sec
entrance delay sec
alarm duraton min
Notes:
Alarm system JA-63 „Profi“ - 15 - MGK51504
Detectors
position location in the house
detectors
type
reaction*
section
A B S
WIRELESS DETECTORS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
WIRED INPUTS
1.
2.
3.
4.
*
I – instant D – delayed F – fire P – panic T – tamper N – next delayed
Alarm system JA-63 „Profi“ - 16 - MGK51504
Notes:
Loading...