JABLOTRON JA-183MB малого размера, коричневый, JA-183M малого размера Jablotron_JA-183M_Installation_Manual_ENG_MLL51600_11762.pdf
JA-183M Wireless magnetic door detector
The JA-183M is a component of Jablotron’s alarm system. It is
designed to detect the opening of doors, windows etc. The batterypowered detector communicates via Jablotron radio protocol.
Installation
Installation shall only be undertaken by technicians holding a
certificate issued by an authorized distributor.
Choose the suitable place for detector’s installation. The
detector reacts to the removal of its magnet unit. The electronics should
be installed onto the non-moving part of windows or doors, and the
magnet onto the moving part. Avoid locating it directly on a metal frame
as metal influences the functioning of the magnetic sensor and radio
communication.
1. Open the detector cover by pressing the tab in. (Fig. 1)
Fig. 1 and 2
2. Screw the rear cover to the solid part of the door/window. The
marks A and B show the right position of the magnet. (Fig. 3)
4. Enroll the detector into the control panel (receiver). Check its manual
for more info. The enrollment signal is transmited when the battery is
inserted. Note: To enroll a detector after having already connected a
battery, first disconnect the battery, and press and release the tamper
sensor to discharge any remaining charge to get the device ready for
enrolment.
5. Set the detector’s reaction See settings chapter.
6. Mount the front cover onto the rear part
7. Test the detector’s function.
8. The tab can be fixed using supplied screw (Fig. 2).
Settings
The DEL position of the jumper provides entrance & exit delays
for detectors installed in a building entrance. INS position allows the
detector to instantly trigger alarm activation if the control panel is
armed.
Note: This DIP switch (INS/DEL) only has an effect if the
detector has a natural reaction assigned to its address in the
Jablotron control panel. It also has no effect when used with a
JA-182N or JA-180N receiver.
The detector has two differ ent modes. The mode is indicate d
by one or two short flash when the battery is ins e rt ed.
One flash means that it indicates both opening and closing the
door or window. The control panel knows the status of doors /
windows. Two flashes means the pulse mode in which the detector
indicates only opening the door or window.
The mode can be set (changed) when keeping the tamper
switch pressed while installing the battery for 3 to 5 seconds.
Testing the detector
15 minutes after closing the detector cover, the LED indicates
detector triggering. The strength and quality of detector signals can
be measured by the control panel in Service mode.
Fig. 3 and 4 - 1. mounting holes of the detector; 2. mounting holes of the
magnet A, 3. magnet A and B position marks; 4. serial number; 5. reed
contact; 6. battery CR123A; 7. tamper; 8. settings jumper
3. Attach the magnet to the moving part of the window. The standard
magnet in a plastic housing opposite the A arrow and the whorl
shape magnet against the B arrow. Its distance from the detector
should be as small as possible when the door/window is closed. In
the picture Fig. 5 and Fig. 6 are shown the reaction areas for
magnets in millimeters in three axes of movement and on the nonmagnetic / magnetic surface. Note: Use the supplied plastic part to
compensate the possible height difference for magnet A.
Battery replacement
The detector monitors its battery voltage and if too low, a report
is sent to the control panel to inform the installer or user. The
detector continues to function and shows each triggering of the
detector with a flash of its LED. Battery replacement should not be
delayed by more than two weeks. This should be done by a
qualified technician with the control panel in Service mode.
Note: If a partly discharged battery is inserted then the LED
start flashing for one minute. Then the detector will work but the
Lo Bat signal will be send to the control panel. Expired batteries
should not be thrown into the garbage, but disposed of according to
local regulations.
Removing the detector from the system
If a detector is removed, the control panel reports the removal.
The detector has to be deleted in the control panel before
intentional removal.
Technical parameters
Voltage: Lithium battery type CR123A (3,0V 1,5 Ah)
Typ. battery lifetime: approx. 3 years for max.20 daily activations
Communication band: 868.1 MHz, Jablotron protocol
Communication range: approx. 300m (open area)
Typical sensitivity range: see Fig. 5 and Fig. 6
Dimensions: transmitter part 75 x 31 x 23 mm
A magnet: 56 x 16 x 15 mm, B magnet: Ø10 x 4 mm
Operational environment according to EN 50131-1:
II. Indoor general
Operational temperature range: -10 to +40 °C
Classification: grade 2
according to: EN 50131-1, EN 50131-2-6, EN 50131-5-3
Complies with: ETSI EN 300220, EN50130-4,
EN55022, EN 60950-1
Can be operated according to: ERC REC 70-03
JABLOTRON ALARMS a.s. hereby declares that the
JA-183M is in compliance with the essential
requirements and other relevant provisions of Directive
1999/5/EC. The original of the conformity assessment
can be found at www.jablotron.com
.
Note: Although this product does not contain any
harmful materials we suggest you return the product to
the dealer or directly to the producer after use.
Fig. 5 and 6
JA-183M Bezdrátový magnetický detektor otevĜení 1 / 1 MLL51600
Loading...