JABLOTRON JA-151A-BASE-RB с электроникой беспроводной уличной сирены JA-151A JABLOTRON_100_JA-151A-BASE-RB_.pdf

JA-151A RB Wireless external siren

||

|

JABLOTRON ALARMS a.s.

Pod Skalkou 4567/33 46601 Jablonec n. Nisou

Czech Republic www.jablotron.com

The JA-151A RB is a component of the JABLOTRON 100
system. It is used for system alarm indication outside a building and
as a pre-sensing tamper detector. It can also be used for
supplementary acoustic signalling (PG activation, arming, chirps).
The siren is equipped with a backup battery which powers the siren
when the main power is disconnected.

by assembling two parts, the with the JA-151A-BASE-RB base PCB and
one of a few optional covers in the JA-1X1A-C-xx series. The covers are
supplied as a colour combination of cover and flasher.

The JA-151A RB is completed

The siren should
be installed by a trained technician with a valid certificate issued by
an authorized distributor.

For combinations of colour and cover material see the following table:

Cover type Colour and cover

JA-1X1A-C-GR

JA-1X1A-C-ST

JA-1X1A-C-WH

JA-1X1A-C-GR-B

JA-1X1-C-ST-B

JA-1X1A-C-WH-B

material

Grey plastic

Stainless steel sheet

White plastic

Grey plastic

Stainless steel sheet

White plastic

Strobe colour

Red

Blue

Installation

The siren should be installed on a vertical wall, with the flasher
facing downwards. Avoid installing the siren near the gutters and on
other places where there is a danger of ice accumulation.

Fig: 1 – hole for installing; 2 – piezo sounders; 3 – NiCd battery with reusable

battery strap; 4 – hole for cable; 5 – 12V DC power cable; 6 – PCB; 7 – spirit

level; 8 – hole for installation with tamper detection; 9 – front cover screw;

10 – string with clip connecting the front cover for easy installation

1. Push the power cable (5) through the hole (4) in the bottom part

and secure it using the plastic tabs.

2. Attach the siren onto a suitable place using 2 screws through the

holes (1) and (8). The spirit level can be used for easy
installation (7).

3. Connect the backup battery to the connector (13).

4. Connect the mains power cable to the terminals (11).

5. Proceed according to the control panel installation manual.

Basic procedure:
a. There must be a JA-110R radio module installed in in the

control panel.

b. When the power supply is connected, the yellow LED (14)

starts flashing to indicate that the siren has not been
enrolled into the system.

c. Go to the F-Link software, select the required position in the

Devices tab and launch the enrolment mode by clicking on
the Enroll option.

d.

Press the button marked LEARN (15) – the siren is thus
enrolled and the yellow LED indicator goes off.

6. Put back the siren cover and attach it using the screw (9).

Fig 2: 11- 12V DC power terminals; 12 – piezo siren connection (attention: high

voltage); 13 – backup battery connection; 14 – yellow fault indicator;

15 – LEARN (enrolment) button; 16 – external antenna connection;
17 – external antenna jumper; 18 – high intensity red LED flashers;

19 – production code

Internal settings of the siren

The siren properties can be set in the Devices window of the F-link
software. When at the siren position, use the Internal settings option
to open a dialog window where you can set: (default settings are
marked *):

Sections: to set for which sections the siren should indicate an
alarm, as well as setting the chirps. The default setting is

indication for all sections.

Reaction: defines whether the siren should indicate EW*

(external warning) or IW (internal warning); Alarm indication can also
be disabled completely (other functions remain enabled).

LED indication: Red* / Blue. According to the siren cover you
can choose the colour of the LED indicators.

Siren sound: interrupted*, uninterrupted.

Alarm indication length: 1, 2, 3*, 4, 5 minutes.

Chirps during section control YES / NO* if enabled, the siren

chirps once upon setting and twice upon unsetting and three times
upon unsetting after an alarm. The signalling only works for the
preset sections.

Siren flashing options: During alarms */ (flashes) 30 minutes
after an alarm. Extended flashing can be terminated by new system

setting or cancellation of alarm indication in the system (with a
keypad).

Flashes every 60 seconds: YES / NO* optional indication of
siren functioning.

PG output activity indication

The siren can indicate the activity of selected PG outputs with its
chirps.

Chirp 1 – slow chirping - 1 per second (for the whole period when
the PG is active)

Chirp 2 – rapid chirping - 2 per second (for the whole period when
the PG is active)

Chirp 3 - 1 chirp when the PG is activated, 2 chirps when the PG
is deactivated

Chirp 4 – a long 20 sec chirp when the PG is activated

Sound priorities

The siren sound has the highest priority, the control chirps have a
lower priority and the PG output activity indication has the lowest
priority (PG1 has a higher priority than PG2 etc). A chirp with a
higher priority always terminates a chirp with a lower priority.

Note: Acoustic power depends on battery charge level.

External antenna use

To improve the communication quality between the control panel
and the outdoor siren you can connect an external antenna (AN-80,
AN-81, AN-868-2PIN). Plug the antenna into the connector (16) on
the PCB. When an antenna is plugged in, disconnect the jumper
(17).

Caution: an external antenna has no protection against

tampering.

JA-151A RB Wireless external siren 1 / 2 MMG51107

JA-151A RB Wireless external siren

The system reports a low battery automatically. The control panel must
be in service mode before you start changing the battery otherwise a
tamper alarm will be triggered. Use a BAT-4V8 battery only.

Technical specifications

Backup battery replacement

Power 12 V DC

Communication frequency 868.1 MHz, JABLOTRON protocol
Communication range approx. 300 m (open area)
Backup battery / lifetime NiCd pack 4.8 V / 1800 mAh

Piezo electric siren 100 dB/m
Dimensions 200 x 300 x 70 mm
Classification security grade 2
According to EN 50131-1, EN 50131-4, EN 50131-5-3
Environmental class IV general outdoor -25 to +60°C
Security grade IP44
Also complies with ETSI EN 300 220-1, EN 50130-4,

Can be operated to ERC REC 70-03

230V AC/12 V DC optional adaptor (DE-06-12)

approx. 3 years

- minimum loaded voltage 4.0 V

(replace the battery when voltage drops down this value)

- maximum unloaded voltage 6.0 V

EN 55022, EN 60950-1, EN 50581

JABLOTRON ALARMS a.s. hereby declares that the JA-151A RB
is in a compliance with the relevant Union harmonisation legislation:
Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU.
The original of the conformity assessment can be found
at www.jablotron.com - Section Downloads.

Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer
or directly to the producer after use.

JA-151A RB Wireless external siren 2 / 2 MMG51107