The JA-110Z - BUS splitter with tamper protection
The JA-110Z BUS splitter serves for splitting the JABLOTRON
100 system BUS. It is protected against tampering by a pair
of tamper contacts. It is supplied with a JA-190PL box/housing for
which this module has been designed. It also includes a couple of
4 input/output terminal blocks to be used as an auxiliary for
the connection of usual wired zones.
It occupies one position in the system. The product can only
be installed by a trained technician with a valid certificate issued
by an authorised distributor.
Installation
The splitter should be installed into the JA-190PL supplied box.
For the tamper contacts, functioning and measuring the voltage
loss on the system BUS the module has to be enrolled
to the system.
b. Go to the F-Link software, select the required position
in the Devices tab window and launch enrollment mode
by clicking on the Enroll option.
c. By pressing the front tamper contact (4) the module is thus
enrolled to the system and the yellow LED (1) indicator
goes off.
Note: The module can also be enrolled to the system by entering
its production code (6) in the F-Link software (1400-00-0000-0001).
The production code can be found on the sticker under the bar
code, glued on the PCB of the module.
If a module will not be enrolled to the system then it is going
to work as a usual splitter with no tamper protection and no voltage
loss measuring.
Setting the module properties
The module properties can be set in the Devices window
of the F-Link software. When at the module position, use
the Internal settings option to open the dialogue window where
you can set the following options (*factory default settings):
Lower/rear tamper: Enabled* / disabled (7).
Note: Optical indication is according to the JA-100 system
standard.
Yellow LED (1) – flashes when the module is not enrolled
in the system yet, permanent light represents a Fault.
Red LED (2) – LED represents activation of the tamper
contacts. Blinks when their status is changed
(activation / deactivation).
1. Attach the JA-190PL box (with a splitter inside) to the required
place. When the splitter is placed out of the protected area it’s
necessary to use a JA-110T BUS isolator. Or when one
of the branches is directed out of the protected premises then
install the JA-110T BUS isolator onto this specific leg to protect
it against tampering (shorting) without influencing to the rest
of the BUS.
2. Connect the BUS cable to the terminals (3). The BUS terminals
are connected in parallel so no terminal is determined
||
|
as an input or output.
Figure 1: 1 – yellow LED indicator; 2 – red LED indicator;
3 – BUS terminals; 4 – front tamper contact; 5 – auxiliary terminals;
6 – production code
Figure 2: 7 – lower/rear tamper contact
When connecting the module to the
system BUS, always switch the power off.
Technical specifications
Power from the control panel BUS 12 V (9…15 V)
Current consumption (in standby mode) 5 mA
Current consumption (for cable choice) 5 mA + connected detectors
Dimensions 76 x 54 x 30 mm
Classification according to EN 50131-1, EN 50131-3 Grade II
Operational environment according to EN 50131-1 II. Indoor general
Operational temperature range -10 to + 40 °C
Comply with EN 50130-4, EN 55022
JABLOTRON ALARMS a.s. hereby declares that the JA-110Z
is in a compliance with the relevant Union harmonisation legislation:
Directives No:
of the conformity assessment can be found at www.jablotron.com Section Downloads.
Note: Although this product does not contain any harmful materials
we suggest you return the product to the dealer or directly
to the producer after use.
2014/30/EU, 2011/65/EU. The original
JABLOTRON ALARMS a.s.
Pod Skalkou 4567/33 46601 Jablonec n. Nisou
Czech Republic www.jablotron.com
If the module is placed out of the
protected area, it is necessary to protect
the system BUS using a JA-110T isolator.
3. Proceed according to the control panel installation manual.
Basic procedure:
a. When the system is switched on, the yellow LED (1) starts
flashing repeatedly to indicate that the module has not
been enrolled into the system yet.
The JA-110Z – BUS splitter with tamper protection 1 / 1 MLV51102
Loading...