JABLOTRON JA-110G-CO для подключения Ei208W(D) детектора углекислого газа JA-110G-CO_EN_MNV51101_manual_inst_EN.pdf

The JA-110G-CO BUS module for carbon monoxide detectors Ei208(D)W

The JA-110G-CO is a plug-in module that can be connected
directly to the Ei208W / Ei208DW stand-alone carbon monoxide
detectors and will allow BUS connection to the JABLOTRON 100
system. It provides information about alarm activation
or deactivation and low battery status.

The module occupies one position in the system and should
be installed by a trained technician with a valid certificate issued
by an authorised distributor.

Installation

Select an appropriate installation place considering

the Ei208(D)W detector installation manual

Note: Enrolling the module to the system is possible by entering

the production code (4) via F-Link software. All digits
in the production code are required (1400-00-0000-0001).
The production code can be found on the sticker under the bar
code, glued on the PCB of the module.

To perform testing and normal operation see the Ei208(D)W

detector installation manual.

Technical specifications

Power from the control panel BUS 12 V (9…15 V)
Current consumption in standby mode 5 mA
Current consumption for cable choice 5 mA
Dimensions 48 x 19 x 14 mm
Environmental class II. indoor general (acc. EN 50131-1)
Operational temperature range -10 °C to +40 °C
Comply with EN 50130-4, EN 55022, EN 50581

JABLOTRON ALARMS a.s. hereby declares that the JA-110G­CO is in a compliance with the relevant Union harmonisation
legislation: Directives No: 2014/30/EU, 2011/65/EU. The original
of the conformity assessment can be found at www.jablotron.com

-Section Downloads.

Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer
or directly to the producer after use

.

a.s.

||

|

JABLOTRON ALARMS

Pod Skalkou 4567/33 46601 Jablonec n. Nisou

Czech Republic www.jablotron.com

Figure: 1 – Ei 208(D)W detector, 2 – connector to plug-in an Ei208(D)W

to a module, 3 – JA-100 system BUS terminal, 4 – production code,

5 – LED indicator

Installation procedure:

When connecting the module to the system
BUS, always firstly switch the power off.

1. Open the detector by turning anti-clockwise against

the mounting base

2. Use the supplied silicone pad for installation. The pad

eliminates unwanted airflow through the detector installation
holes. Airflow could have a negative influence on carbon
monoxide detection

3. Put the cable through the silicone pad and mounting base

(punch a hole through the prepared places)

4. Attach the mounting base to the wall. Make sure the detector

clings to the silicone pad reliably (possible leakage could have
a negative influence on detector measurement)

5. Connect the BUS wires to the module terminal (3)

6. Plug the module into the detector´s connector (2). Pay attention

to correct cable storage to avoid module extrusion from
the detector

7. When the system power has been turned on then the yellow

LED (5) flashes and it indicates the module is correctly
connected but has not been enrolled to the system yet.
The LED indicator shines through the front panel above
the ALARM indicator.

8. Using F-Link software, select the required position

in the Devices window and launch the enrollment mode
by clicking on the Enroll option.

9. Assemble the detector onto the mounting base and lock

it by turning clockwise. The module is thus turned on and
enrolled to the control panel simultaneously. The yellow LED
(5) goes off.

JA-110G-CO BUS module for carbon monoxide detectors Ei208(D)W 1/1 MNV51101