Page 1
User manualJABLOTRON 100
DESCRIPTION OF KEYPAD (Access module with segments)
For the most convenient control and status indication the JABLOTRON 100 system offers various types
of access modules. Controlling (setting, unsetting and other available functions) can be done just by pressing
one button on the two-button segments. Moreover, the buttons are backlit in order to clearly indicate the
segment status at fi rst sight. The segments can also be used to control various devices – heating, window
shutters, gates, etc. An arbitrary number of segments can be used as needed.
Continuous yellow
PARTIALLY SET
Flashes red
ALARM
Continuous green
EVERYTHING OK
Flashes green
CONTROL
Continuous yellow
FAULT
When controlling the system using buttons on segments the command must be confi rmed with
authorization. This can be done by applying an RFID card or by entering a code on a keypad. Authorisation
can be done by RFID cards / tags of the OASiS system, Azor system or any other one working with EM
125kHz. If a high security level is required, it can be set so that the card authorization must be confi rmed
by entering an access code on a keypad. On the other hand mainly for home automation usage the control
via segments can be simplifi ed by setting that for setting or controlling devices no authorization is required.
This feature can be used e.g. to control window shutters on the house using a keypad.
Another advantage of controlling the system using segments is the possibility to carry out multiple
commands at the same time – it is therefore possible to set the house section with one segment, set
the garden section alarm with the second one and unset the garage section with the third one. Only one
authorization is required after selecting all options via segment buttons.
The authorization code entered on a keypad can consist of up to seven characters. It includes a prefi x
(one to three digits) a separating star and a four-digit code. It can thus be for example 123*1234 or 1*1234.
This code can be simplifi ed for buildings with only a few users by omitting the prefi x. Only a four digit code
is then used.
Card reader Keypad with a reader
Keypad with a LCD display
and a reader
Access module
CARD READER / KEYPAD
Continuous red
SET / ON
Flashes red
ALARM / ALARM MEMORY
Continuous green
UNSET / OFF
Flashes green
ENTRY DELAY
Page 2
User manualJABLOTRON 100
ALARM SETTING
The command is executed:
The keypad acoustically indicates
an exit delay. When it becomes
silent, the given section is set 3).
I confi rm the command by
authorization:
By applying a card or a tag
or by entering a code on
a keypad ...
I want to set the alarm:
I press the segment button of
the corresponding section
which then starts fl ashing ...
The command is executed:
The segment LED turns permanently green to indicate an unset
section 3).
I confi rm the command by
authorization:
By applying a card or a tag or
by entering a code on
a keypad ...
ALARM UNSETTING
I want to unset the alarm:
When I enter the building, the
entrance delay is triggered. It is
indicated by an uninterrupted
beeping sound and repeated
fl ashing of the green LED on
the button. I press the fl ashing
button ...
COMMAND AUTHORIZATION EXECUTED
COMMAND AUTHORIZATION EXECUTED
Note: Sections with an entrance delay can be unset via a code or chip reading only without segment
button pressing. In the case of a requirement to unset the other sections, it is necessary to press segment
buttons before authorization.
Note: In standard settings, active detectors will by bypassed automatically, or depending on the installer
settings you can be asked to confi rm bypassing active sensors by double-pressing a segment button, or the
system can be refused to be set until the deactivation of detectors.
Page 3
User manualJABLOTRON 100
If enabled, partial setting which guards only with selected detectors can be set. You can thus guard for
example windows and doors overnight, while motion detectors ignore movement inside the guarded building.
The command is executed:
The keypad LED turns yellow to
indicate partial setting 3).
I confi rm the command by
authorization:
I authorize myself by applying a
card or a tag or by entering
a code on a keypad ...
I want to set the alarm partially:
I press the segment button
which starts fl ashing yellow ...
If we need complete setting (e.g. when leaving the building), it is necessary to press the button twice in the
fi rst step. When you press the button for the fi rst time, the LED starts fl ashing yellow and it turns red after the
second press. When the authorization is confi rmed, the system is set completely.
When the alarm is set partially (yellow LED lit), it can be set completely by repeating the setting procedure
one more time. Partial setting can be set without an authorisation request
3)
.
PARTIAL ALARM SETTING
TERMINATING A TRIGGERED ALARM
COMMAND AUTHORIZATION EXECUTED
COMMAND AUTHORIZATION EXECUTED
It may happen that you forget to unset the system and trigger an alarm. The keypad LED fl ashes red together
with an LED on the corresponding segment. You can terminate the alarm by unsetting the system. An LED on
the segment then indicates the alarm memory
3)
.
Page 4
User manualJABLOTRON 100
Using a keyfob
The button function is shown by the lock symbols. A closed lock button sets
the alarm while an open lock button unsets it. Concurrent pressing of both buttons
sends a panic alarm signal.
The buttons can be blocked against unintentional pressing (child lock). For
more information see the keyfob manual.
Using the voice menu
The alarm can also be controlled using a mobile phone voice menu which guides you through the selection of functions. When you enter the menu, the fi rst
thing you are informed about is the alarm status. If voice menu access is enabled
for all telephone numbers, you are required to enter a code (on the phone keypad).
Another possibility is enabling access from authorized telephone numbers only (the
telephone contacts stored in the alarm memory).
When an alarm is triggered, the system informs you with a voice message 3).
Using SMSes and dialling-in
SMS commands can be used to control various devices – heating, sunblinds,
etc. in the same way as segments. The SMS text form is CODE COMMAND.
Command wording can be set according to the actual situation, e.g. SUNBLINDS
DOWN. It can be set that no code is required before the command. You can also
enable control by dialling-in from an authorized number. If preset then such a call
is rejected by the control panel, therefore it can be free of charge and the preset
command is automatically executed.
If there is an alarm, the system can send you an informative SMS
3)
.
Via the Internet
The alarm can also be controlled via the Internet using the web SELF SERVICE
interface which is accessible from www.jablonet.net. To be able to use this web
service previous one-time control panel registration is required. Please ask your
installer for more details.
OTHER MEANS OF CONTROL
- with a keyfob, by telephone and via the Internet
The system also indicates that there was an alarm while you were away in the same way. In such an event be
wary while inspecting the building or wait until the security agency response team arrives.
The segment keeps indicating the alarm memory until it is set again. The indication can also be terminated
by repeating the procedure above. Clearing this indication is possible on the internal menu of the LCD keypad.
Main menu – Clear alarm memory indication
.
Page 5
User manualJABLOTRON 100
KEYPAD WITH LCD - Main menu
2)
A user or the system administrator can do partial diagnostics using this keypad or make some small changes
to the system settings.
Main menu
Press ENTER. The display shows you the
Main menu
. Using buttons or select
the desired option. Confi rm your selection by pressing the ENTER button. Then authorisation will be requested. Do the authorisation using your access code or an RFID card
/ tag. The selected option can be changed according to your restriction level. Leave the
main menu by pressing the ESC button or let it be terminated automatically after the 5
minute time-out.
Clear alarm
memory
indication
Press ENTER. The display shows you the
Main menu
. Using buttons or
select
Clear alarm memory indication
and confi rm your selection by pressing
ENTER. Authorise yourself. The alarm memory will be cleared in all sections for which
you have access. Stop the activity by pressing ESC.
Section
control
Press ENTER. The display shows you the
Main menu
. Using buttons or select
Section control
and confi rm your selection by pressing ENTER. Authorise yourself.
By pressing buttons or select the section and by pressing ENTER the selected
section will be set. By repeated selection it is possible to set more sections. When
partial setting is allowed, press ENTER once to set the section partially, press ENTER
again to set fully. The set system status is shown on the display by the highlighted
numbers of particular sections. A non highlighted section is an unset section, an unfi lled
square around the number = partially set, a fi lled square around the number = fully set.
An exit delay or setting is executed immediately by selecting the section. By the same
procedure it is possible to perform unsetting. The section control menu is terminated by
pressing the ESC button (repeatedly).
Event
memory
Press ENTER. The display shows you the
Main menu
. Using buttons or select
Event memory
and confi rm your selection by pressing ENTER. Authorise yourself. By pressing buttons or you can read the basic list of the event memory.
In the upper status bar the time when the event occurred is visible. By pressing
ENTER on a selected event it shows a detailed log. In this detailed listing, use buttons
or to scroll through the details of other events. Terminate the event memory menu
by pressing the ESC button (repeatedly).
Active
detectors
Press ENTER. The display shows you the
Main menu
. Using buttons or select
Active detectors
and confi rm your selection by pressing ENTER. The LCD display
shows you a list of detectors which were active at the moment of pressing the ENTER
button. By pressing buttons or you can scroll through this list. The list shows you
the section to which the detector has been enrolled, its position and the name of the
detector. Terminate the active detectors menu by pressing the ESC button (repeatedly).
Bypassed
detectors
Press ENTER. The display shows you the
Main menu
. Using buttons or
select
Bypassed detectors
and confi rm your selection by pressing ENTER. The
LCD display shows you a list of detectors which were bypassed at the moment of
pressing the ENTER button. By pressing buttons or you can scroll through
this list. The list shows you the section to which the detector has been enrolled, its
position and the name of the detector. The system does not react to bypassed
detectors at all. (Turning the detector’s bypassing on and off can only be done by
a User with Admin authorization via the Settings menu). Terminate the Bypassed
detectors menu by pressing the ESC button (repeatedly).
RF detectors
without
response
Press ENTER. The display shows you the
Main menu
. Using buttons or select
RF detectors without response
and confi rm your selection by pressing ENTER.
The LCD display shows you a list of detectors from which the system has repeatedly not
received periodical transmissions. By pressing buttons or you can scroll through the
list. The list shows you the section to which the detector has been enrolled, its position
and the name of the detector. To fi x this problem, contact your installer. Terminate the
RF detectors without response menu by pressing the ESC button (repeatedly).
Page 6
User manualJABLOTRON 100
Detectors with
low battery
Press ENTER. The display shows you the
Main menu
. Using buttons or
select
Detectors with low battery
and confi rm your selection by pressing ENTER.
The LCD display shows you a list of detectors from which a low battery was reported.
By pressing buttons or you can scroll through the list. The list shows you the
section where the detector has been enrolled, its position and the name of the detector.
The batteries have to be changed within the next 14 days of the low battery report.
For battery changing it is necessary to bypass the particular detector. Then when
batteries have been changed cancel the bypasses (Settings – Devices). Terminate the
detectors with low battery menu by pressing the ESC button (repeatedly).
Active tampers
Press ENTER. The display shows you the
Main menu
. Using buttons or
select
Active tampers
and confi rm your selection by pressing ENTER. The LCD display
shows you a list of active tampers. By pressing buttons or you can scroll through
the list. The list shows you the section to which the detector has been enrolled, its
position and the name of the detector. To fi x this problem call the installer (installation
company). Terminate the active tampers menu by pressing the ESC button (repeatedly).
Faults
in the system
Press ENTER. The display shows you the
Main menu
. Using buttons or select
Faults in the system and confi rm your selection by pressing ENTER. The LCD display
shows you a list of detectors in which a fault was detected. By pressing buttons or
you can scroll through the list. The list shows you the section to which the detector
has been enrolled, its position and the name of the detector. To fi x this problem call
the installer (installation company). Terminate the Faults in the system menu by pressing the ESC button (repeatedly).
Settings
Press ENTER. The display shows you the
Main menu
. Using buttons or select
Settings
and confi rm your selection by pressing ENTER. Authorise yourself. The LCD
display shows you the
Users
and
Devices
settings (only for Administrator authorisation). Choose which settings you want to change (Users or Devices) and confi rm the
selection by pressing ENTER.
User settings
: The User name is displayed. By pressing buttons or select,
what you want to change: code, telephone number, access card no.1 or access card
no.2. By pressing ENTER on the selected option open the option to change the data
by numerical buttons. Changes can be saved by pressing ENTER. Other options are
changeable by the same procedure. Leave the menu after saving the data by repeatedly pressing ESC. You are then asked
Save settings?
Save or don’t save and give
confi rmation by ENTER and changes are updated in the system or cancelled.
A user with administrator authorization can change the settings of other users in
sections for which he has access privileges.
Devices settings
(only for Administrator authorisation): The display shows you the
position and the name of the device. Press the ENTER button and then using buttons or select the device for which you want to change the settings. By pressing
ENTER on the selected position open the option to program
Bypass
with settings
YES / NO
. Confi rm a change by pressing ENTER. When you choose
YES
, the device
is bypassed and the system will not react to it. A bypass can be cancelled if you
choose the opposite option NO. When changes are complete, you can leave the
menu by repeatedly pressing ESC. You are then asked to
Save
or
Don’t save
the
settings. Confi rm it by ENTER and the changes are updated in the system or cancelled.
Terminate the settings menu by pressing ESC (repeatedly).
Display
settings
Press ENTER. The display shows you the
Main menu
. Using buttons or select
Display settings
and confi rm your selection by pressing ENTER. The LCD display
shows you the list of parameters, which can be changed. By pressing buttons
or select the required option. By pressing the ENTER button on the selected parameter you open the parameter options.
Contrast
is selectable in the range 1 to 5.
LCD backlight
and
Keypad backlight
are selectable in the range 0 to 5. 0 = keypad
backlight is turned off.
Service
Only for installation companies.
Page 7
User manualJABLOTRON 100
1)
Possible for keypad fi rmware LU60x10 and higher and control panel fi rmware LJ60408 or MD60408 and
higher.
2)
The whole menu is available for keypad fi rmware LU60x10 and higher and control panel fi rmware LJ60408
or MD60408 and higher. Lower fi rmware only makes the menu partially available.
Firmware upgrades can be done by the installer.
3)
During installation it is possible to set different features. Change the above functional description together
with the installer in accordance with the actual settings.
NOTES:
Page 8
User manualJABLOTRON 100
For questions and further information contact your installer.
MLJ57102
NOTES:
Loading...