The “Athos” CA-1802 and CA-1803BT GSM pagers
Thank you very much for buying our CA-1802/CA-1803BT GSM pager. Now you will always be able
to find where you left your car. Jablotron s.r.o.
Alarm
When an alarm is triggered, warning SMS messages will be sent to all phones (TEL1 to TEL4)
and these phones will also be called with a siren sound
Remote control by SMS instructions
You can operate the car alarm remotely via SMS instructions sent from an authorized phone
(TEL1 to TEL4). Factory default instruction texts are shown in the following table. If an SMS is
sent from an unauthorized phone a valid user code must be entered before the instruction (e.g.
USER IMO).
In the case that you do not remember particular SMS instruction(s) you can
ask for help by sending a HELP instruction.
Remote control from an unauthorized phones
You can operate the car alarm via SMS instructions sent from arbitrary mobile phone, even an
unauthorized one. In that case, the user code must be inserted at the start of every SMS
instruction, separated by a space. Example: MYCODE STATUS. The factory default value of
user code is USER. The code can be modified by an instruction. See the table above or ask a
service center for help.
SMS instruction texts
Default Your text Description
IMO
UNIMO
STATUS
GPS
LOCATOR
HELP
CREDIT
AUX
parameter
UC xx...x
Only basic ASCII can be used in the SMS instruction texts.
Ask the installer to edit the SMS commands for you.
1
If a call is activated after an alarm has been triggered and you answer the call, you will hear a siren sound
from the receiver. If a hands-free set is installed, listening to the car will be triggered.
2
CA-1803BT only
3
Only applicable if supported by the GSM provider.
4
A qualified technician is required for setting up this function.
CA-1803BT, CA-1802 User manual – mode 3
STOP (immobilize) the vehicle (if installed)
Unblock (mobilize) the vehicle (if installed)
GSM pager will reply with status information
To obtain vehicle’s location via GPS
To obtain vehicle’s location from the GSM provider
GSM pager will reply with a brief list of SMS
To obtain the balance of a prepaid SIM card if used
To operate appliances
To change the user code (do this after installation).
- 1 - MHF57100
1
.
2
instructions.
xxx…x is the new user code, 4 to 8 characters (A –Z
& 0 – 9). The factory default user code is USER
3,4
4
...
LED indicator signals
Car location via
GPS
LED indicator is used to
show the status of the
alarm.
Warning! If the LED
indicator starts flashing
fast after the ignition is
switched off, it will not
be able to send any
messages nor call in the
case of an alarm.
LED state Meaning
OFF
Permanently ON
Flashing fast
Interrupted light
Flashes after
turning the
ignition key on
Ready
Connecting to a GSM network or a
phone call
GSM network is not available
Vehicle was stopped (immobilization)
The number of flashes corresponds
to the number of controllers enrolled.
Remote immobilization (IMO)
When the GSM pager receives the SMS command IMO it will reply with a confirmation SMS
and block (immobilize) the engine. If the ignition key is off, the immobilization will occur
immediately. If the ignition key is on when the car alarm receives the command IMO,
immobilization will occur as soon as the ignition key is switched off which will be
confirmed by SMS. Unblocking the car cannot be done by a key fob. It is only possible by the
SMS instruction UNIMO.
After receiving a GPS instruction, the GSM pager will respond with the GPS coordinates of
(CA-1803BT only)
the latest known location. If the current location is not available at the time of reception of
the instruction (as the case may be for the vehicle being in a deep-level garage), the latest
location stored in internal memory is sent. To monitor the vehicle temporarily, you can use
the GPS ON instruction which makes the GSM pager send information about location after
every 1 minute of time elapsed (limited to 15 messages).
Example of an SMS response with a
GSM pager reports: Location: (GMT:3.12.10:35)
50*43.495N;15*11.253E;515;50, Time:3.12.05 11:35
(GMT:3.12.10:35) Greenwich Mean Time (prime meridian)
50*43.495N;15*11.253E latitude and longitude
515 altitude (approximated)
50 current velocity
Time:3.12.05 11:35 current local time
GPS
location:
Location via the LOCATOR service
If you use a SIM card which enables for an approximate car location via the GSM network,
you can send a
Example of an SMS response sent from the GSM network:
+420603012345 Kraj: Jihocesky, Okres: Jindrichuv Hradec, Nazev: Nova Ves nad
Luznici. Vzdalenost asi 5.4 km. E14*52'1"@ N48*50'24", + -200m 15:23:01 18.09.06
Internet remote access and maintenance
The web site www.gsmlink.cz enables pager’s remote control (to users) and setting (to
installers). After a registration of the GSM pager you get a secure password protected
access. You can check the pager’s state, modify it or change settings for phone numbers
and texts. In addition, it is possible to get a listing of event records (with time, source, and
type information) as well as the vehicle motion history
When it is necessary to change the settings of the GSM pager, you mostly do not need go out for
a service. Instead, you can call and ask a service engineer to perform the setting remotely.
CA-1803BT, CA-1802 User manual – mode 3
LOCATOR
SMS instruction to obtain the car location3.
3
.
- 2 - MHF57100
Phone calls by an installed hands free set
If the HF-03 hands free set is installed, it is possible to receive and make phone calls via the car
alarm. In addition to hands free calling, the set allows you to listen-in after an alarm has been
triggered.
Incoming calls
while the GSM pager is disarmed. The set allows you to receive a call from any phone
number but only when the ignition key is turned on.
To make a call
pressing one of the buttons of the RC-8x controller you will dial the corresponding number
(preprogrammed by the installer). Each button can be assigned to a phone number.
To terminate a call –
When armed, all incoming calls are automatically rejected. If the vehicle is blocked (by the IMO instruction)
all calls are automatically answered (it is then possible to listen to and to speak to the vehicle remotely).
– to answer them, press any button on the RC-8x key fob remote control
– you can call up to 4 preprogrammed numbers while you are driving. By
4
press any button on the RC-8x controller.
Additional features
Car battery low voltage reporting
The built-in voltage drop detector can trigger an alarm if an electrical device in the GSM pager is
turned on. Also the pager checks the voltage of the vehicle’s battery (the threshold limit is 10.5V).
The pager can be backed up by a BB-02 battery. Except for the acoustic siren, the BB-02 backsup all the functions of the car alarm. After discharging or disconnecting the main battery supply
an SMS will be sent with corresponding information.
Remote control of another appliances
If connected with another car’s appliances (e.g. independent heating), the GSM pager allows you
to operate them via the RC-8x controller or by sending an SMS instruction AUX. If you use the
RC-8x key fob for operation, press the buttons
instruction see the table below for a detailed description. In addition, SMS operation allows you to
determine the requested impulse duration to activate an appliance.
Instruction Status
AUXA (B) Relay switches on for 1 second
AUXA ON (OFF)
AUXB ON (OFF)
AUXA xxM or xxxS
AUXB xxM or xxxS
You can replace AUX with HEATING or any other word which will suit you.
ON – switch on permanently (ON can be replaced by 1)
OFF – switch off permanently (OFF can be replaced by 0)
Maximum switch-on (switch-off) time is 60 minutes.
xxM – requested duration of the relay to be switched on, in minutes
xxS – as above, in seconds
Roaming
If you travel abroad and your SIM card supports roaming, the pager’s functionality remains
unrestricted except for the LOCATOR and CREDIT functions which might be not available.
Central monitoring station communication
The car alarm allows central monitoring via GPRS data protocol. Please ask your supplier for details.
Your installer’s contact details:
Jablotron s.r.o. ▪ Pod Skalkou 33 ▪ Jablonec nad Nisou ▪ 483 559 911 ▪ www.jablotron.cz
CA-1803BT, CA-1802 User manual – mode 3
a together. If you operate via the AUX SMS
Troubleshooting
Contact the company responsible for the car alarm
installation. You can also contact the manufacturer
directly.
- 3 - MHF57100
Notes:
CA-1803BT, CA-1802 User manual – mode 3
- 4 - MHF57100
Loading...