j&a Cleo-gx, Lenox GX User Manual

-

G

WHIRLPOOL PEDICURE SPA
User’s Manual

Please read user’s Manual thoroughly
before using pedicure spa

X

Pedicure Spa

Copyright 2010 by J&A USA Inc.
Printed in USA

Table of Contents

Table of Contents

Introduction & Safety

Identify Parts & Description

Consideration

Specification

Dimension

Drainage Connection

Installation Summary

Maintenance ( Dura-Jet)

Maintenance (Magna-Jet (OPTIONAL)

Discharge Pump

Chair / Backrest attachment

Disinfecting Pedicure spa

User Recomendation

UL Certificate

Back Flow Prevention Device

Warranty

Thank you for choosing GX series , This finest Whirlpool Pedicure Spa has been develop by UPS (United
Pedicure Spa) a subsidiary of J&A USA Inc., to bring quality and exquisitely balanced design yet afford-ability and
dependability when properly use. Please read this entire manual thoroughly before installation and use

PLEASE TAKE TIME TO READ THIS MANUAL THOROUGHLY BEFORE USE. If you have any questions or
concerning with our pedicure spa, Please contact our customer service and technical support at 631-243-3336 ext 121,
Monday through Friday 9AM - 5PM or email us at [e-mail]

Important requirements

The MFG requires that you contact your local, licensed plumber and licensed electrician to install your new spa. Installation MUST
be in compliance with all local and state building codes. Your pedicure spa can not operate efficiently or safely unless it is provided
with adequate electrical power, sufficient water pressure, proper water temperature, and required drainage capabilities. Contact your
local building inspector for information and local code compliance procedure that need to be followed when having your new pedicure
spa installed. Subsequent inspections and approvals that may be required are the responsibility of the purchaser.

Shipment Inspection

Examine the components immediately upon arrival to make sure no damages to the pedicure spa base and chair during the shipment. It
is very important that you notify the driver directly and notation should be on the face of the freight bill or bill of lading of any
damage. Failure to note damage on the bill of lading may prevent any claims you may have against the carrier.

If concealed or damage is found, you MUST notify the carrier at once and request an inspection. DO NOT DISCARD THE
SHIPPING CARTON If receiver sign the carrier clean receipt of goods that have been damaged in transit .Do so at your own risk

and expense.

Precaution

- Do not stand in the basin of the spa.

- Excessive water temperature is dangerous and should be checked before use. Maximum water Temperature should not exceed
100F (38C).

- Always enter and exit the spa slowly and carefully.

- Never bring or operate any electrical device near pedicure spa.

- The unit has a weight capacity of 250 pounds.

Health Warning

Individuals whose feet or legs are inflamed or have open wounds should not be allowed to use the pedicure spa at any time. The
technician should advise clients to consult their physician before using the spa if there is any sign of fungal infection, swelling,
fracture, or persistent pain. In some cases diabetics may experience improved circulation in their feet, but should first consult their
physician prior to receiving a pedicure.

If the client experiences any pain or discomfort, discontinue the use of the pedicure spa

immediately.

Identification

Back Mechanism
Cover

Remote Controller
Pouch

-

G

X

Comfort Pillow

Backrest Cover

Easy Access Up & Down
Armrest

Dual Functional
Shower Sprayer

Three Stage
Adjustable FootRest

Basin

Three Stage
Adjustable FootRest

Standard Pipeless Motor
(D3)

Drain Plug

Granule Bowl

Hygienize functional
Drain Handle

FRP Constructed Body

Non Slip Bumpon

A

US

A

J&

Standard Pipless Motor
(D3)

Seven Sequential light

Optional Pipeless Motor
(MG)

Important Considerations

Electrical Service

110V, 60Hz, 15Amp GFCI protected grounded circuit MUST be used to supply power each individual pedicure spa.
And the main circuit breaker MUST be at 25Amp. For maximum of two units per each electrical outlet.

Water Supply

All plumbing connections must conform to local codes.
Water supply to the spa should be provided with adequate water pressure and water temperature.

Water pressure

To fill the basin correctly up to level, Normal water pressure of 30 to 80 P.S.I is required.

Water temperature

The hot water supply temperature must not exceed 140 . Adjust your hot water accordingly. For hot and cold water supply
fittings and drain fittings location, see below diagram .Carefully connect the water supply line to the appropriate fittings
located on the rear of the pedicure spa.

Pressure / Temperature

Maximum Pressure: 150 psi (10 bars)
Minimum Pressure: 10 psi (69kPa)
Working Temperature: 33F to 140F constant; intermittent to 180f
(0.6C to 60C sustained; intermittent to 82.2C)
Recommended Flow: 1.5gpm

UL LISTED / CE CERTIFIED

Compliance with following Code (s): Uniform Plumbing Code, National Plumbing Code of Canada and international
Plumbing Code. Also, Compliance with following Standard (s): ASME A112.18.3M / A112.18.1M, CSA B125, NSF /
ANSI 61

ANSI - American National Institute, ASME - American Society of Mechanical Engineers, CSA - Canadian Standard
Association IAPMO - International Association of Plumbing and Mechanical Officials, UL - Underwriters Laboratory

All J&A USA products has been compliance with requirements for Whirlpool bath appliances contained in ASME / ANSI
A122.19.7M-1995, CSA C22.2 No. 68-69

** Vaccum Breaker

Due to Town and / or State requirement/s are varies in building code, if the Town and / or State requires
Vaccum Breaker, As the Plumber MUST provide Vaccum Breaker according to building code
requirement.

Drain Facilities

The pedicure spa Drain must meet local plumbing codes. Check valve for Drain (not Provided) Must be installed by a licensed
plumber. Also Pedicure spa must be securely fasten to the floor.

Installation Summary

The installation must comply with local, state, an d federal buildi ng, plumbing and e lectrical codes, where applicable. A
licensed plumber should complete the plumbing of the pedicure spa.

Note: Failure to comply with federal, state, or local codes and ordina nces will result i n warranty being n ullified and
void.

-

G

X

Specification

Dimen sion & Weight (Sh ipp ing)

Dimen sion & Weight (Ne t)

Capac ity of Tub

Switc h

Power S ource

Plumb ing Source

War ranty

Due to continuous improvements on all our products, specification, characteristics, packing, color, designs are subject to

Pedic ure Spa with M assage Cha ir
Stool

Pedic ure Spa & Mass age Chair

Cleo GX

Dedic ated 15Amp Wall Outl et Re quire
Pipe - le ss whirlpo ol motor
Disch arge Pump (O ptional)
Massa ge System

Hot Water
Cold Water
Drain

Unit
Optio nal Item

change without notice.

67L x 37W x 40H 275 lbs

20.25 L x 27.25W x 1 7H 19 l bs

55.25 L x 27.75W x 5 5H 22 5 lbs

5 U.S Gal lon

On / Off Air Activ ated Switc h

120Vac, 0.4 Am p. 60Hz,
115Vac, 3.2 Amp. 60H z
120Vac, 60H z

0.5 inc hes (Fitti ng Provide d)

0.5 inc hes (Fitti ng Provide d)

1.5 inc hes (See Plu mbing Inst ruc tion)

One Yea r
120 Day s

DIMENSIONS

-

G

X

45 1/4”

29 1/4”

5 ½”

2”

10”

3 ½”

Rear View

24 ½ ”

14 ½”

16 ½”

Open Tray
8”

21 1/2”

Front View

29 3/8”

Side View

54”

5 1/8”

14 7/8”

6 3/4”

27 3/8”

7 3/4”

-

G

X

DRAIN

Back Flow Prevention Device (Dual Check Valve)

Pedicure spa is/are equipped with the subject device as standard feature, sold to following state
Effective April 01 2005: AZ, CA, NE, NV, OR, TX and WA
Effective June 15 2005: IL, MN, WI and MI
Effective May 01 2007: CT
All J&A Products are Equipped with Backflow Protection (Dual Check Valves) as Standard
as indicated in the manual.

BASEMENT DRAIN CONNECTION

2”

5 ½”

3 ½”

16 ½”

15 ½”

WALL DRAIN CONNECTION

6”

10”

14 ½”

24 ½ ”

Rear View

Power Drain (An Optional At Request)
(See detailed power drain pump)

2 3/4”

41”

15 ½”

Installation Specifications Summary

Warning: Failure to comply with federal, state or local codes and ordinances will result in warranty being null and void.

As stated, the pedicure spa installation must comply with all plumbing and electrical codes. A licensed plumber and
licensed electrician must complete the applicable connections of the pedicure spa.

Location and support

Select a level location. The floor structure beneath the pedicure spa must be capable of supporting the occupied pedicure
spa.

For the seat back to fully recline, the pedicure spa base must be mounted as follow from the wall as shown below:

*** When chair slide all the way back – would require 20 inches from the wall***
*** When chair slide in the middle – would require 15 inches from the wall***
*** When chair slide all the way to the front – would require 12 inches from the wall***

Above measurement are based on with back cushion is all the way reclined

Due to continuous improvements on all our products, specification, characteristics, packing, color, designs are subject to

See Detailed info
on top of the page

change without notice.

Dura-Jet III

Safety Instructions

When using electrical equipment, basic safety precautions should alwa ys be followed to reduce the
risk of fire, electrical shock, and injury to persons, including the following:

1. Read and follow all instructions before using the equipment.

2. Keep the cord out of heavy traffic area. To av oid fire hazard NE VER put the cord und er the rugs, near heat generating
devices.

3. Always turn off the equipment be fore servicing .

4. Do not drop or insert any object into any openings.

5. Do not operate any equipment with a damage parts.

6. Any other use not re commended by the manufacturer may electrical shock or injury to persons.

7. Never use outdoors

8. Do not attempt to repair or adjust any electrical or me chanical funct ions on the unit.

A

S

U

A

&

J

Feature

1. Dual powerful massage jet-streams

2. Jet assembly can be attached from the pump for
quick cleaning and sanitizing.

3. Built-in electronic sensor for pump control.

4. AC motor (long lif e)

5. Extremely low power consumption .

Cleaning Instruction

1. Ensure the unit is off

2. Remove the front cover

3. Remove the impeller and impeller cover

4. Use anti-bacterial solution ( EPA r egistered) to cl ean all plastic parts.

5. Reassemble the front cover

DURA-JET III Specific ations

Model: DURA_JETIII -

120Vac, 0.4 Amp. 60Hz,

Pump: Dual Air Jet Fl ow

Mounting: Single 3.5” hole
Auto tighten Moun ting screws(4)

6. Manufactured in USA.

When us ing electr ical equip ment, Basi c safety precau tions must b e followed t o red uce the risk o f fire, electrical shock, and
injur y to Persons .

1. Read a nd follow al l instruct ions befor e using the eq uipment.

2. Keep e lectrica l cord out of he avy traffic area. To avoid fire h azard NEVE R place elec trical cor d under the ru g, near heat
Gener ating devi ces.

3. Always turn power off the equipment before service.

4. Do not d rop or inser t any object i nto any open ings.

5. Do not o perate any e quipment w ith damage d parts.

6. Any other use not recommended by the manufacturer may cause electrical shock or cause injury t o person/s .

7. Neve r use it outdo ors

8. Do not a ttempt to re pair or adju st any elect rical or mechanical.

Motor

Round
Magne tic Field (h ousing)

Magne tic
Jet Bas e

Magne tic
Impel ler

Magne tic
Whirl pool jet cov er

1. Hydr o dual massa ge jet strea m

2. Magn etic whirl pool jet cov er can be remo ve for quick
clean ing and sani tizing.

3. Buil t-In elect ronic sens or for pump co ntrol.

4. AC Whirlpool motor (long life)

5. Very l ow power con sumption ( 27W)

6. Manu factured i n USA.

1. Turn off the unit and wait until the motor is fully stops.

2. Hold H ydro whirl pool jet cov er firmly an d pull to sepa rate from th e round magnetic field.

3. Turn hydro whirlpool jet cover to left to open and pull out impeller.

4. Use Anti - Bacterial solution (EPA Registered) to clean all parts.

5. After sanitize all parts, place impeller and close hydro whirlpool jet cover to tu rn right to lo ck

6. Hold f irmly the wh irlpool co ver jet and ge ntly place it onto the round magnetic field. Do not release the hydro whirlpool jet cover until
Jet cov er is on the rou nd magneti c housing.

Hydro -Massage D ual jet Flow

Diame ter

How to USE Magnetic jet !

WARNING: DO N OT RU N DRY, BASIN MU ST FI LLED WITH WATER TO LEVEL INDICATOR.

CAUTI ON: MAGNET IC JET COVER ASSEM BLY MUST ALIGN WITH D ISCHARGE P ORT
POSIT IONED AT 3/9 O’CL OCK.

WHEN RE ADY TO USE, MAKE S URE JET COVER IS PO SITIONED AT 3 /9 OCLOC K FOR
PROPE R WHI RLPOOL ACTI ON IN THE BASIN. IF J ET CO VER IS NOT ALIGN AT 3/9 O’CLOC K,
WATER WILL SPLASH OUT SIDE OF THE BASIN .

PROPER WAY TO USE MAGNETIC JET SYSTEM

1- FILL THE WATER TO WATER LEVEL INDICATOR.

2- HOLD MAGNETIC JET FIRMLY TO BRING CLOSER TO THE ROUND MAGNETIC FILED AND DO NOT RELEASE
THE MAGNETIC JET PREM ATURELY OR THIS WILL CAUSE IMPACTS ON THE J ET COVER AND THE ROUND
MAGNETIC FIELD(HOUSING) SHORTENING THE LIFE EXPECTANCY OF THE JET COVER . WHEN THE JET
COVER NEARS THE ROUND MAGNETIC FIELD, PLACE JET COVER ONTO THE FOUR DIMMPLE AREA (SEE
DIAGRAM). THE JET COV ER MUST ALIGN WITH DISCHARGE PORTS POSITIONED AT 3/9 O’CLOCK.

3- WHEN FINISHED WITH C LIENT, DO NOT REMO VE MAGNETIC JET UNTIL MO TOR IS FULLY STOPPED.

4- WHEN MOTOR IS FULLY STOPPED, REMOVE MAGNETIC J ET COVER FROM THE MOTOR AND REM OVE JET
COVER AND IMPELLER FOR SANITIZATION.

Motor

Bottom View of
Magnetic Jet Base

Magne tic
Jet Bas e

Magne tic
Impel ler

Magne tic
Whirl pool jet cov er

Round
Magne tic Field (h ousing)

-

G

X

Discharge Pump ( Optional):

Up to 4ft @ +/- 39 sec. with 1/2” Connection to main drain

Fastner

On/Off
Switch

Discharge (Drain) outlet MUST be 1/2” or 3/4”
for efficient drainage.

Check valve required

(SMALL Rubber Coupling)

LARGE Rubber Coupling

3/4” Elbow

3/4 PVC Pipe

3/4” PVC Pipe

HANNING DPO 40 - 020

Rubber Gasket

Elbow

(LARGE Rubber Coupling)

Air Check Valve

Clear Tubing 3/4 OD ½”ID

Poly Insert 90 Elb ½”

3/4” PVC Pipe

TEE 3/4 X 3/4 X ½

Installation Instruction

1. Make a hole ( size 1-3/8”) for the On/Off switch as shown (see fig 1). Pre-
drill required.

2. Placed a 1/8” clear hose into the rear of the switch and on/off switch into the
hole.

3. The discharge pump kit is made to fit onto the pedicure unit. (see fig 2)

4. Connect E-Z connector onto the drain elbow.

5. Plug discharge pump outlet into the two minute timer outlet

6. Plug two minute timer into the wall outlet.

7. It is very important that tip of the clear tub remain above the water Level with
one loop as shown.

** Please cut to fit 1” Flex hose to your size**

3/4 SLIP X ½” Male Adaptor

Power Plug
to wall outlet

Pipele ss Mo tor
Power Pl ug

2 Min.Timer
(D.pump)

3/8” Clear Tube from on/off for D/P pump
insert into 2 Min. Timer.
Make sure to push in tightly.

Electrical Con tro l Box
(Located left bo tto m
inside of base)

3/8” clear Tube
from On/Off Switch
for Part time control box

Light

T
ransf

o

PA

E

TIM

PART

FUL L TI ME

rm

RT T

e
r

IME

Operation Instruction

Warning ! DO NOT RUN DRY

1. Turn to open drain plug. 3 to 5 second for air to release from the pipe

2. Press On/Off switch to activate timer.

3. At any time, water drain completely from the basin. Press
On/Off switch to stop or built in two minute timer.

1-3/8” Hole
for On/Off Switch

Figure 1

Fastner

On/Off
Switch

Recliner Piston End Attachment Instruction

Bott om of Backrest

Recliner
Bracket

Recliner
Pi ston end

Cl evis pin
sp acer

A

B

C

Recliner pis ton
en d - Mu st be
Ho rizontal position

D

Lo ck ing
pi n

Cl evis Pin

1. Rem ove Clevis pin from recliner piston end and make sure it is in horizontal position.

2. Slowly raise u p the backrest to aligned with recliner piston.

3. Insert Clevis Pin into the backrest bracket through reclin er piston and secure with locking pin.

Recliner Piston End Attachment Instruction

Bott om of Backrest

Recliner
Bracket

Recliner
Pi ston end

Cl evis pin
sp acer

1. Rem ove Clevis pin from recliner piston end and make sure it is in horizontal position.

A

B

D

Recliner pis ton
en d - Mu st be
Ho rizontal position

Lo ck ing
pi n

C

Cl evis Pin

2. Slowly raise u p the backrest to aligned with recliner piston.

3. Insert Clevis Pin into the backrest bracket through reclin er piston and secure with locking pin.

DISINFECTING YOUR PEDICURE SPA

Note: Please be advised that it is responsibility of purchaser/user to adhere strictly to the following procedure.

Any non-compliance will be considered negligence of the purchaser/user.

The Bureau of barbering and cosmetology requires that salons using whirlpool pedicure spas use the following disinfecting
Procedures to ensure proper cleaning and maintenance of the equipment, and to prevent bacterial infection. For your clients
safety, always use the regulations as a minimum standard for cleaning and disinfecting.

Chair maintenance
Please see chair manual for Do and Don't

At the end of the day:

1. Remove the intake suction screen, All debris trapped behind the screen of each pedicure spa must be removed.
And the screen and the inlet shall be washed with soap or detergent and water

2. Before replacing the screen, Totally immersed the screen into an EPA- registered disinfectant with bactericidal,
Fungicidal, and virucidal activity.

3. Finally, flush the whirlpool system with low-suding detergent and warm OR an EPA - registered cleanser for
10 minutes. Rinse with clean fresh water and drain.

Note:

Cleaning or sanitizing is NOT disinfecting. According to the CDC and EPA, disinfecting occours only when there is a
reduction of pathogenic microbes at 99.999%. Sanitizing is a only reduction of 99.9%. Cleaning of whirlpool pedicure spa
requires surfactant and chelating detergents that are low foaming and have ability to remove body oils, organic oil
additives, mineral oil, skin cell, nail clippings, etc.. that can accumulate both in the basin and the jets which may become
fertile area for micro organism to grow.

Note:
The use of oil based products can build up in the whirlpool system causing clogging in the jet and build up onto the surface
of the basin. Adherence to the above cleaning will minimize build up thus the manufacturer recommend not to use mineral
oil based product.

USER RECOMMENDATION

PLEASE READ THE MANUAL THROUGHLY BEFORE USE TO ENSURE CORRECT
OPERATION.
THOSE UNDER A DOCTORS CARE OR WHO ARE EXPERIENCING ONE OR
MORE OF THE FOLLOWING DONDITIONS SHOULD CONSULT THEIR DOCTOR
BEFORE USE.

- You are receiving medical treatment or are feeling ill.

- Your body shows any cute symptoms.

- You have heart disease.

- You are pregnant or having a menstrual period.

- Your doctor has ordered you to rest.

- You have a back disorder resulting from an accident or disease.

- You have a high fever.

- You have sensory disorders.

- You have medical electrical device (e.g. pacemaker).

- You have service interruption in the circulation of the legs.

- You are diabetic.

FAILURE TO DO SO MAY RESULT IN ACCIDENTS AND HEALTH PROBLEMS.

Back Flow Protection Device
(Dual Check Valve)

May.1.2014

In accordance with applicable Local or State regulations,
J&A USA Inc., The manufacturer of the pedicure whirlpool spa certifies that the following models are
equipped with factory installed Dual Check Valve back flow preventer:

** Lenox Series
** Cleo Series
** Episode Series
** Pacific Series
** Petra Series
** Toepia Series

The specification of the installed device is as follows:

J&A USA Inc.

335 Crooked Hill Road
Brentwood, NY 11717
Tel: [phone]
Fax: [phone]

www.jausainc.com

DEVICE NAME

DEVICE
MANUFACTURER

DEVICE MODEL

DEVICE
SPECIFICATION

DEVICE
PRESSURE

DEVICE
TEMPERATURE

DUAL CHECK VALVE BACKFLOW PROTECTION

NEOPERL INC.
Waterbury CT.

Dual Check Valve 1/2” x /2”NPT

TESTED AND CERTIFIED TO MEET NSF/ASSI 61
Complies with ANSI/ASME A112.18.3M, A112.18.1M
AND CSA B125

MAXIMUM PRESSURE: 150 PSI (10 BAR)
SERVICE PRESSURE : 80 PSI

MAXIMUM TEMPERATURE : 150F
SERVICE TEMPERATURE : 90F

ALL MODELS OF PEDICURE SPA MENTIONED ABOVE ARE EQUIPPED WITH THE SUBJECT DEVICE
AS STANDARD FEATURE. As for your information, indicated State requires Vaccum Breaker.

** Effective April 01 2005:

ARIZONA, CALIFORNIA, NEBRASKA, NEVADA, OREGON,
TEXAS AND WASHINGTON

** Effective June 15 2005:
ILLINOIS, MINNESOTA, WISCONSIN, MICHIGAN

** Effective May 01 2007:
CONNECTICUT

For additional information, Please contact us at 631-243-5300
Very Truly yours,

Technical Support

Limited Warranty

Pedicure Spa

IMPORTANT

To validate the limited warranty, The Limited Warranty Registration Form MUST be filled out completely and return to J&A
USA within 30 days of original purchased date. This Limited Warranty is valid if J&A USA received registration form.

J&A USA Inc. Pedicure Spas has designed and manufactured with the highest standards and expressly warrant the pedicure spa as
follows:
To the original owner of the J&A USA Inc. Pedicure Spa may repair or replace, at its option, any pedicure spa found to be defective in
material or workmanship upon inspection by a authorized representative of J&A USA Inc. This limited warranty covers the following:

Base - Twenty four (24) month from date of shipment from J&A USA facility.
Components / Parts - Twenty four (24) month from date of shipment from J&A USA facility.
Stool - Ninety (90) days from date of shipment from J&A USA facility.
Shipping Costs - Twenty four (24) month from date of shipment. J&A USA will cover normal shipping costs associated with

replacement parts. Expedited shipping cost will incur an additional charge.
Labor - Twelve (12) month from date of shipping, J&A USA Inc will cover reasonable labor costs associated with the
installation of replacement parts found to be defective in material or workmanship upon inspection by authorized
representative of J&A USA INC.

No labor cost or replacement parts will be covered under this limited warranty if at the sole discretion of J&A USA
INC. it is determined a failure was caused by negligence, accident or improper use, improper installation or lack of
proper maintenance as in the Owner’s Manual.

NO CONSEQUENTIAL, INCIDENTAL, CONTINGENT, INDIRECT, SPECIAL OR OTHER DAMAGES WILL BE
ALLOWED. This warranty is null and void if the pedicure spa is removed from its original installation or is not installed accordance

with specifications of pedicure spa or national, state or local codes, regulation and ordinances. Furthermore, this limited warranty is
null and void if the pedicure spa is subjected to improper installation or maintenance, negligence, improper cleaning or any other
circumstance beyond J&A’s control. To validate limited warranty, pedicure spa must be installed by a licensed plumber and/or
electrician in accordance with local and / or State code and pedicure spa installation instructions.

Warranty Exclusion

1- Unauthorized repairs and/or modification or tampered in any way.
2- Damage due to freight, accident, natural disaster and /or abuse or misuse
3- Stain, fading or discoloration of seat, back cover, armrests ( Upholsteries), Tray or Footrest
4- Fading, discoloration or staining of basin or Any portion of surface of pedicure spa caused by water additive or improper
water treatment (such calcium built up) and/or cleaning agents/s
5- Damage or malfunction due to improper installation including but not limited to, failure to comply with all national, state
and local plumbing, electrical and building codes.
6- Magnetic jet assembly (base, impeller and cover) due to J&A provided an extra jet assembly to accommodates wear-tear.
7- Damage drain pump due to residue built up in drain pipe and / or due to the lack of maintenance.

Parts for which labor / Service is NOT COVERED - Following components are simple to replace and DO NOT require a service

technician. Therefore, though the part is covered under the guidelines of the warranty agreement.

1- Panel
2- Jet cover, impeller and / or jet assembly
3- Faucet Cartridge, Shower Head
4- Footrest
5- Air actuate On/Off Button
6- Drain Plug
7- Remote control

During the Limited Warranty period, J&A will, at its sole discretion, repair o r replace any defective component. All
component parts removed under this Limited Warranty become propert y of J&A USA Inc. And all replacement component
/s MUST be return to J&A USA I nc. within 20 days o f replacement. If not, replaced component/s will be charge as its cost/s.

This limited warranty is for the original owner and not transferable . The original o wner agrees by usi ng pedicure spa th e
obligation of J&A USA shall not extend to indirect or contingen t damage or injury. Furthermore, the obligations of J&A are
limited to those set forth herein. The limited warranty is the exclusive remedy and is in lieu of all other warranties, express
or limited, including but not limited to, any implie d warranty of fitn ess or merchantability for a particular purpose.
No distributor or other person has the right or authority to bind J&A USA INC to changes to this limited warranty.
Consequently, J&A USA INC is not responsible for such warranties or repres entations.

Limit ation of lia bility

TO THE EXTENT ALLOWED BY LOCAL LAW, EXCEPT FOR THE OBLIGATIONS SPECIFICALLY SET FORTH IN THIS WARRANTY
STATEMENT, IN NO EVENT WILL J&A OR ITS THIRD PARTY SU PPL IER S BE LI ABL E FOR ANY DAMA GED C AUS ED BY J&A’S PED ICU RE
SPA OR THE FAI LUR E OF J& A PEDI CUR E SPA INCL UDI NG ANY LOST PR OFI T OR SAVIN GS, B USI NES S INT ERR UPT ION , LOS S OF US E OR
ANY OT HER C OMM ERC IAL OR ECONOMIC LOSS OF ANY KI ND, O R SPE CIA L, IN CRE MEN TAL, OR CONSEQUENTIAL DA MAG ES. THIS
LIMITATION OF LIABILITY A PPL IES WHETHER DAMAGES ARE SOUGHT, OR A CLA IM MA DE, U NDE R THIS LIMITED WA RRA NTY OR AS A
TORT CLAIM, A CONTRACT CLAIM OR ANY OTHER CLAIM.

Limited Warranty Registration Form

IMPORTANT

To validate the limited warranty, The Limited Warranty Registration Form MUST be filled out completely and return to J&A
USA within 30 days of original purchased date. This Limited Warranty is valid if J&A USA received registration form.

Serial No.:

J

A

Your Salon E-Mail Address:

First Name : Last Name :

Salon Name :

Salon Address :

City :

State:

Name of Distributor :

Zip Code:

Tel (Salon)

Cell

Area Code:

Area Code:

Phone :

Phone :

Date of Purchase (mm/dd/yyyy):

City :

Completed Warranty Registration Form to : J&A USA Inc.
335 Crooked Hill Road Brentwood N.Y 11717
or Fax to 631-243-3339 or email to [e-mail]

Questionnaire ( We value your voice!)

1. Are you satisfy with Pedicure spa received?

2. Are you currently using J&A product/s? If so, How long?

2. If not, What other product ?

4. What is the most important features in choosing Pedicure Spa?

5. How long in business?

6. How often are you remodel Your Salon?

7. Would you purchase J&A product in the future?

State:

Yes : No :

Yes : No :

Brand
Price

Year/s

Year/s

Yes : No :

Zip Code:

Design

Other

Function

Year/s

Service

8. Do you want to receive a promotion by email ?

9. Any suggestion or Comment

Yes : No :